MAINT REPAIR TO PLUMBING SANITARY FITTING FLOORING MASONARY JOINERY INCL CERTAIN BR WORKS AND REPAIR REPLACEMENT OF GAUDIAN LIGHTS LT UG CABLE UNDER GE I GOS

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off premises complete all as specified and directed

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment.

M & L coloured vitrified tiles Light shade 10 mm thick (square/rectangular) polish area of each tiles n exc 0.36 Sqm coloured cut to required size set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles as in floor incl 15 mm thick screed bed in CM 1:4 ,complete all as specified and directed .

M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Demolition of cement concrete un reinforced in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring average 25 mm thick surface finished even and rough (as in levelling course) to receive the topping layer complete all as specified and directed.

Taking down cement or cement lime plaster, of any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on RCC ceiling surface and finished even and smooth with out using extra cement complete all as specified and directed .

M&L for applying 2mm thick Birla / JK Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper ,complete all as specified and directed .

M&L for applying two coats of oil bound distemper on wall or concrete surfaces over & including a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and apply three coat of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceilings and apply three coat of white wash complete all as specified and directed.

M & L for two coats of cement based paint over a coat of primer on new plastered surface of walls including preparation of surface complete all as specified and directed.

M&L for Complete removal of existing treatment and applying two coats of OBD over a coat of alkali resistant primer on wall complete all as directed by Engineer-in-Charge.

M&L for preparation of old decorated surfaces of wall with complete removal of existing treatment and applying two coat of cement based paint over a coat of primer complete all as specified and directed.

M&L applying two coats Cement based paint on old decorated wall surfaces, includes complete removal of existing wall finish of any type with wire brush, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc complete all as specified and directed.

M&L applying two coats of acrylic exterior weather proof emulsion paint over a coat of exterior primer on newly plastered wall surfaces/ old decorated wall surfaces, in case of old decorated wall surfaces includes complete removal of existing wall finish of any type with wire brush, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc complete all as specified and directed.

M&L preparation of old painted surfaces and applying one coat of oil bound distemper on walls complete all as directed.

M&L for preparation of old wood or wood based surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of old decorated wooden painted surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old steel surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation of old decorated Steel painted surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for two coats synthetic enamelled paint to new steel surfaces after preparation over a coat of red oxide primer area over exc 10cm in width or girth etc complete all as specified and directed.

M & L for two coats of distempering with 1st quality washable plastic acrylic distemper (ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification after preparation of plastered surface including a coat of primer on prepared surfaces including, rubbing with sand paper and applyingn.

Taking down chowkhat or frames n exc 1.50 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed

Taking down chowkhat or frames exc 1.50 Sqm and n exc 4 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories.) (Area not exceeding 2.00 sqm)

S & F Powder coated three track Aluminium sliding window with frame not less than 1.8 mm thick excluding aluminium grill and including 4 mm thick tinted glass, beading & necessary rubber packing, locking & opening arrangement, all fitting and fixture complete all as specified and directed.

S&F 7mm thick aluminium grills of make "Decogrill' model DG 104 surrounded by aluminium 'C' channel with mesh size 75 X 75mm all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and averagewidthof aperture1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet re-inforced with MS square tube in opening as per specification and shown on drg SSR Part-II 2010 ,complete all as specified and directed .

S&F, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain cover PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rails lock rail and bottom rail on either side & as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement , as per specification and shown on drawing in SSR Part-II (2020) ,complete all as specified and directed .

Taking down shutter of any description area exceeding 1 sqm but n exc 2 sqm each and removing to store complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F Flush shutters 35 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sidescomplete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Taking down shutter of any description not exceeding 1 sqm each leaf and refixing, in same opening after easing and adjusting building hard ware etc complete all as specified and directed

Taking down shutter of any description exceeding 1 sqm but not exiding 2 Sqmeach leaf and refixing, in same opening after easing and adjusting building hard ware etc complete all as specified and directed

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and directed.

S&F 100 mm long aluminium handles cast type, anodized complete all as specified and directed

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed

S&F in repair 100 mm long aluminium anodized handles fabricated type complete all as specified and directed

S&F in repair 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and directed.

S&F in repair 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed

S&F in repair 75 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed

S&F in repair 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed

S&F in repairs 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Hacking out old broken glass (any thickness, size quality or description) form wooden frames or stone, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and gazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed.

S&F 3 mm thick figured glass pin headed type and gazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed.

S&F in repairs aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed.

S&F in repairs 18/19 mm thick high density PVC/ WPC solid fibre board with prelaminated PVC sheet as Almarh cupboard and frame including taking down the old cupboard shutters and removing to store complete all as specified and directed.

S&F continuous (piano) hinges of width of flaps (when open) 30 mm, mild steel, bright finish or electrogalvanised complete all as specified and directed

S & F magnetic catcher catcher with nut and screw of mild steel bright finish all as specified and directed

S & F 40 mm dia cupboard knobs fixed with nuts screw and washer of mild steel bright finish complete all as specified and directed.

S & F in repair 40 mm dia cupboard knobs fixed with nuts screw and washer of mild steel bright finish complete all as specified and directed.

S & F in repair hasp and stapple safety type aluminium anodised 75 mm long with mild steel hinge pin including bolt to hinge plate fixed with screw complete all as specified and directed.

S&F in repairs 15 mm dia Curtain rods, mild steel, chromium plated with fixing brackets complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodised, over all length of cover plate 140 mm with hard drawn steel spring fixed in door etc complete all as specified and directed.

S & F in repair sheet Glass Shelf assembly consisting of 5.5 mm glass sheet shelf 12 cm wide with cromium plated bracket guard and railing 60 cm long complete all as specified and directed..

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade (ISI marked) with all fittings fixed complete to walls, ceilings or laid in floors of 15 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade (ISI marked) with all fittings fixed complete to walls, ceilings or laid in floors of 20 mm bore of pipe complete all as specified and directed.

Supplying and laying as in repair of CPVC pipes 25mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified or laid in floors concealed or open of any length including taking down or up existing GI tubing & connections ,complete all as specified and directed .

Supplying and laying as in repair of CPVC pipes 32mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified or laid in floors concealed or open of any length including taking down or up existing GI tubing & connections ,complete all as specified and directed .

Refixing old steel tubing and connections in new or old position (wall, floor, ceiling etc) of 15 mm bore of pipe complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (wall, floor, ceiling etc) of 20 mm bore of pipe complete all as specified and directed.

S&F in repair Chromoium plated Bib cock with flanges Quarter turn 15 mm bore complete all as specified and directed. Make-Jaquar , Cera & equivalent as approved by GE and Engineer in Charge.

Taking down bib tap /wash basin tap/pillar tap/stop cock/mixture tap and refixing the same after repair and replacement of washer only for 15 mm bore size without replacing spindles complete all as specified and directed.

Taking down bib tap /wash basin tap/pillar tap/stop cock/mixture tap and refixing the same after repair and replacement of spindles for 15 mm bore size complete all as specified and directed.

S&F in repair Chromoium plated angular stop cock for 15 mm bore complete all as specified and directed. Make-Jaquar , Essco, Cera & equivalent as approved by GE and Engineer in Charge.

S&F in repair Chromoium plated Two-way angular stop cock for 15 mm bore complete all as specified and directed. Make-Jaquar , Essco, Cera & equivalent as approved by GE and Engineer in Charge.

S&F in repair, 15 mm bore stop cock, cast copper alloy with long shank and cup (concealed type) fancy type chromium plated screwed down high pressure with crutch & butterfly handle screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair 15 mm bore stop cock, cast copper alloy screwed down high pressure with crutch & butterfly handle fancy type chromium plated screwed both ends for iron pipe and fixed complete all as specified and directed .

S&F in repair pillar tap cast copper alloy with capstan head chromium plated crewed down high pressure with or without lettered hot or cold with long screwed sharks and ply nuts 15 mm dia complete all as specified and directed

S & F in repair bottle trap chromium plated for WHB as per approved quality all as per specified and directed.

S&F in repair PVC waste pipe for WHB etc all as specified and directed.

S&F in repairs 32 mm bore dia waste coupling of (min weight 32 mm-45 gm of PTMT) (half or full threaded) etc complete all as specified and directed

S&F in repair CP grating 100 mm dia with waste hole (minimum weight 40 gm) complete all as specified and directed

S & F in repair CP Jet spray for 15 mm bore all as specified and directed.

S & F in repairs Hand shower (Health faucet) with 1 mtr long Easy flex tube in crome finish & wall hook ,complete all as specified and directed .

M&L in repairs for vitreous china wash basin, white,flat back, size 550 x 400 mm including supply & fixing of brass chromium plated coupling 32 mm etc complete all as specified and directed.

M&L in repair Wash down water closet vitreous china white pedestal pattern with 'P' or 'S' trap including connecting to outgoing drain pipe & to flushing pipe excluding flushing cistern and flush pipe complete all as specified and directed.

S&F in repairs plastic water closet seat cover, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

M&L in repairs vitreous china squatting pan , ‘Orissa’ Pattern, size 580 X 440 mm white, with integral foot rests etc. complete all as specified and directed.

S & F in repair Kitchen sink made of stainless steel 1 mm thick with plug washer and waste pipe incl bedding fixing cantilever brackets and connetction union to pipe overall size 915 X 460mm bowl size 405X 355 mm complete all as specified and directed

S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 litre capacity hoisted and fixed in position including dismantling of old u/s water tank and removing to store complete all as specified and directed

S & F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity hoisted and fixed in position including dismantling of old u/s water tank and removing to store complete all as specified and directed

S&F ball valves for 20 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed.

S&F ball valves for 25 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 455 gms) complete all as specified and directed.

S&F in repairs ball valves for 20 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed.

S&F in repairs ball valves for 25 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 455 gms) complete all as specified and directed.

S & F in repair PVC Tank cover for 500 Ltr capacity fixed in position with nuts and bolt complete all as specified and directed

S & F in repair PVC Tank cover for 1000 Ltr capacity fixed in position with nuts and bolt complete all as specified and directed

S&F in repairs, PVC valveless symphonic action type low level flushing cistern, 10 ltrs capacity with inlet, ball valve, float and handle including bracket complete all as specified and directed

S & F in repair internal fitting for low level flushing cistern (Syphon) complete all as specified and directed.

S&F in repairs flush pipe 32 mm dia of polyethylene of low or high density or PVC, for low level cistern complete all as specified and directed.

S & F in repair 125 mm dia chromium plated shower rose of with or without swivel joint incl fixing to steel pipe complete all as specified and directed.

S&F in repair PVC connection 15 mm bore, 450 mm long complete with both ends unions complete all as specified and directed.

S&F in repairs CP anodised tubular tower rail, 20 mm dia, D type, 60 cm long between flanges etc ,complete all as specified and directed .

S & F in repair 75 mm PVC(SWR) floor trap with grating incl jointing with solvent cement complete all as specified and directed

S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe of 20 mm bore dia of pipe complete all as specified and directed.

S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends (ISI marked) for iron pipe of 25 mm bore dia of pipe complete all as specified and directed.

S & F in repair Soap dish any type fixed to plug with chromoium plated brass screw complete all as specified and directed. Make-Jaquar , Cera & equivalent as approved by GE and Engr-in -Charge .

S & F in repair corner glass shelf with brackets complete all as specified and directed. Make-Jaquar , Cera & equivalent as approved by GE and Engr-in -Charge .

S & F in repair stainless steel SC-Premium Dual Edge - 8 PIN cloth hanger bathroom wall door Hooks, complete all as specified and directed.

S&F in repairs door seal with aluminium beading and 50 mm wide rubber seal complete fixed to aluminium/ Wooden doors complete all as specified and directed.

M&L preparation of old painted surfaces and applying one coat of white wash on walls complete all as specified and as directed.

M&L preparation of old painted surfaces and applying one coat of white wash but on ceiling complete all as specified and as directed.

Demolition of Cement Concrete (unreinforced) of any description & in any position not otherwise specifically provided for complete all as specified & directed.

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and directed

M&L for Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed complete all as specified and directed.

M&L for Cleaning the concerned RCC surface by means of wire brush to expose the concrete surface which should be free from all loose particles, dust, laitance, etc complete all as specified and directed.

M&L for Rendering 5 mm thick in CM 1:3 on RCC ceiling surface and finished even and smooth with out using extra cement complete all as specified and directed.

M&L Rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finish the surfaces even and smooth without using extra cement complete all as specified and directed. Note : Liquid WPC will be measured and paid separately.

M&L Water proofing treatment on "Non approachable / non accessible and approachable roof" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete (i) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm (ii) Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces complete all as specified and directed. (iii) Laying evenly over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard wt not less than 3kg /Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction complete all as specified and directed. (iv) Applying two coats of bituminous aluminium paint including preparation complete all as specified and directed.

Taking down eaves gutters and rain water pipes of any size or pattern including all fittings etc complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F Stack clamps made out of 50x5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 110 mm PVC pipe complete all as specified and directed.

S&F Stack clamps made out of 50x5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 75 mm PVC pipe complete all as specified and directed.

S&F PVC(SWR) bends, any radius of 110 mm bore without access door complete all as specified and directed.

S&F PVC(SWR) bends, any radius of 110 mm bore with access door complete all as specified and directed.

M/L PVC(SWR) Tee of 110mm dia etc complete all as specified and directed.

S&F PVC(SWR) bends, any radius of 75 mm bore without access door complete all as specified and directed.

S&F PVC(SWR) bends, any radius of 75 mm bore with access door complete all as specified and directed.

S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door complete all as specified and directed.

S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 75 mm dia with access door complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap of diameter of outlet 75 mm, plain with grating including jointing with solvent cement 75mm dia etc complete all as specified and directed.

S&F in repairs PVC (SWR) 'P' trap for 110 mm dia etc complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs /blankets, any thickness, including cover fillets complete all as specified and directed.

S&F 12 mm thick plain Gypsum Board False Ceiling with GI frame including all necessary drilling cutting to fix electric items complete all as specified and directed with following:- (a) GI Grid channel 30x25x20 mm of 24 gauge fixed with rawl plug and screw 450 mm centre to centre alongwith perimeter walls. (b) GI channel made to shape 50x40x40 mm of 24 gauge placed @ 600 mm centre to centre from perimeter at wall except long wall (in one span). (c) GI intermediate runners of size 45x10x10 mm of 24 gauge fixed @ 1200 mm centre to centre leaving frame of one side walls (in other span). (d) GI sheet 25 mm wide and 20 mm gauge suspended fixed with steel fastner to roof ceiling and 1200 mm centre to centre including pluging of RCC Slab. (e) 12 mm thick gypsum board filling joints with POP and finishing complete with two coat of plastic emulsion paint over one coat of primer on ceiling.

M&L for Cleaning and removing all scale and dirt, etc, from RCC/PVC tanks exc 250 ltr n.exc 500 ltr capacity incl washing of water tank with the use of Tank cleaning motor jet pressure machine and using bleaching powder @ 0.25 Kgs per tank with writing the date of cleaning with any type of paint and from mouths of circulating pipes, including disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

M&L for Cleaning and removing all scale and dirt, etc, from RCC/PVC tanks exc 500 ltr n.exc 1000 ltr capacity incl washing of water tank with the use of Tank cleaning motor jet pressure machine and using with bleaching powder @ 0.50 Kgs per tank with writing the date of cleaning with any type of paint and from mouths of circulating pipes, including disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

S&F in repairs door closer hydraulically regulated designation No 2, universal type, suitable for door shutter of weight between 36 to 60 Kg of aluminium (Die cast) body complete all as specified and directed.

S&F in repairs door seal with aluminium beading and 50 mm wide rubber seal complete fixed to aluminium/ Wooden doors complete all as specified and directed.

S&F in repairs Stainless Steel Towel Rack 600 mm long with Lower Hangers but with 3 hooks ,complete all as specified and directed .

S & F repair Over head Shower 100 mm round shape single flow (ABS body chrome plated with gray face plate ) with rubit cleaning system complete all as specified and directed.

S & F in repair chromium plated towel ring with bracket complete all as specified and directed.

Taking down rolling shutters including all hardware fittings and removing to store complete all as specified & directed

S&F 1 mm thick of steel rolling shutters without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated, push pull or manual type complete all as specified and directed.

S&F 1 mm thick of steel rolling shutters without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated, but gear operated type with bevel gear box and crank handle complete all as specified and directed.

S&F Ball bearing for rolling shutters complete all as specified and directed.

M&L Cutting holes in brick walls exc one brick but not exc two brick built in cement mortor or cement lime mortor and stone walls built in lime mortor for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

M&L for two coats synthetic enamelled paint to new steel surfaces after preparation over a coat of red oxide primer area over exc 10cm in width or girth etc complete all as specified and directed.

Taking down cover hood of existing rolling shutters (gear operated/ manually size any type ) carefully and completely over hauling the shutters by applying grease and oil in bearing, springs, guide cannels, operating rods, shaft gear boxes, gear wheel etc straightening thoroughly shutter blades, guide channels anchoring rods etc and fixing back the over hood in position and ensure smooth functioning of shutters complete all as directed. (Note : worn out part for replacement will be measured and paid separately.)

Supply and fixing in repairs onlyMS gear box complete incl handle and anchoring rod as of approved quality of steel rolling shutters complete all as specified and directed.

All as per item no. 157 but for Ball bearing suitable for rolling shutter

All as per item no. 157 but for Guide channel 3" (3.50 mm thick)

All as per item no. 157 but for Cover hood made of 1 mm thk plain GI Sheet pattern

All as per item no. 157 but for Bottom plate 5" (2.25mm)

All as per item no. 157 but for C Class pipe 50 mm dia in shaft

All as per item no. 157 but for Anchoring rod of 25 mm dia of MS pipe

All as per item no. 157 but for Safety lever locks MS with 4 levers

M&L for Fe 410-W (Gde E-250 quality A) Framed work as in doors or gates of angle or other section with gusset plates,rails,braces etc complete,drilled for fixing of steel sheeting or other covering. Doors,etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening anf fixing ,complete all as specified and directed.

M&L for applying 2mm thick Birla / JK Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper ,complete all as specified and directed.

M&L for applying 2mm thick Birla / JK Putty in two layers on newly plastered ceiling surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed.

M&L for applying two coats of oil bound distemper on wall or concrete surfaces over & including a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

M & L for two coats of cement based paint over a coat of primer on new plastered surface of walls including preparation of surface complete all as specified and directed.

M&L applying two coats of acrylic exterior weather proof emulsion paint over a coat of exterior primer on newly plastered wall surfaces/ old decorated wall surfaces, in case of old decorated wall surfaces includes complete removal of existing wall finish of any type with wire brush, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc complete all as specified and directed.

M&L preparation of old painted surfaces and applying one coat of white wash on walls complete all as specified and as directed.

M&L preparation of old painted surfaces and applying one coat of white wash but on ceiling complete all as specified and as directed.

M&L applying two coats Cement based paint on old decorated wall surfaces, includes complete removal of existing wall finish of any type with wire brush, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc complete all as specified and directed.

Providing and fixing of false ceiling with powder coated exposed G.I. grid suspension system (E-grid T-2430 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) consisting of main runner 3600 mm lon, cross tee 1200 mm/600 mm long and wall angle. The wall angle shall be fixed on PVC Dash fasterners on the perimeter of the wall by steel screws with distance 300 mm c/c. The main runners to be placed @1200 mm, The cross tee 1200 mm will be inserted in the pre-cut slots of main runner at a gegular interval of 600 mm to form a modular grid of 1200 mm x600 mm. Additonal Cross Tees 600 mm shall be placed perpendiclar to the cross tee 1200 mm long to finally form a grid of 600 mm x600 mm. Grid of module size 600 mm x 600 mm shall be supported by 6 mm dia G.I wire from purlins/soffit. 4mm this High Pressure steam Cured everest non Asbestos Fibre Cement Designer ceiling Board (density .1200 kg/m3, Modulus of Rupture (M.o.R)-15.85 MPa, thermal conductivity(K)-0.0872 W/mK) of size 595mm x595mm, confirming IS 14862& Type B Category III of ISO 8336:1993, (Reaction to fire-A2-S1-d0) tested as per EN 13501Part-I & BS-476 Part 4,5,6 & should be placed in the Grid module to form a False Ceiling. All complete as per the drawing & directions of engineer-in-charge.

Day to day maintenance for Complaint related to carpenter works like door easing, door repair, kitchen cup board repair, window/door wire mesh/glass pane repair, refixing of building hardware etc by deploying carpentor and mazdoor. Note : Five (05) compliants resolved = One (01) Job work. Note : (a) The complaints related to carpenter works, plumbing works, cement works and welding works against serial item Nos 199 to 202 shall be completed in 48 hours time after lodging/ receipt of complaints. Contractor shall ensure that all the complaints shall be attended and completed within above prescribed schedule/ time period, failing which, a penalty at the rate of double the quoted rate for that particular trade work/complaint per day till the satisfactorily completion of complaint shall be levied on the contractor and recovery for the same shall be affected from contractor's dues. (b) Complaint slip and complaint register etc. shall be provided by the contractor without any extra cost to the department and cost there of shall be deemed to be included in quoted rates by the contractor against respective items. (c) Necessary transportations, tools, plants, ladders, including nails, screws, PVC washers, brass spindle, for bib taps/ stop cocks/ pillar cocks, cotton thread, Jumper valves, white lead, flush washers, internal fitting of low level flushing cistern, nipple, tee, elbow, plug, socket, reducer (GI/UPVC), M-seal, glass putty, hinges, handle, tower bolt, aldrop,stopper, cement, white cement, sand other similar minor accessories required to complete the jobs/complaints shall be provided by the contractor without any extra cost to the department and cost there of shall deemed to be included in quoted rates by the contractor against respective item of schedule 'A'.

Day to day maintenance for Complaint related to plumbing works like repair/refixing of Bib tap, Stop cock, Angle cock Connection pipes, waste pipes, Flush tank, Flush pipe,Shower, Pvc tank, ball valves, towel rail, WHB, EWC, waste coupling, Grating,Pillar tap etc.by deploying plumber and mazdoor. Note : Five (05) compliants resolved = One (01) Job work. Note : (a) The complaints related to carpenter works, plumbing works, cement works and welding works against serial item Nos 199 to 202 shall be completed in 48 hours time after lodging/ receipt of complaints. Contractor shall ensure that all the complaints shall be attended and completed within above prescribed schedule/ time period, failing which, a penalty at the rate of double the quoted rate for that particular trade work/complaint per day till the satisfactorily completion of complaint shall be levied on the contractor and recovery for the same shall be affected from contractor's dues. (b) Complaint slip and complaint register etc. shall be provided by the contractor without any extra cost to the department and cost there of shall be deemed to be included in quoted rates by the contractor against respective items. (c) Necessary transportations, tools, plants, ladders, including nails, screws, PVC washers, brass spindle, for bib taps/ stop cocks/ pillar cocks, cotton thread, Jumper valves, white lead, flush washers, internal fitting of low level flushing cistern, nipple, tee, elbow, plug, socket, reducer (GI/UPVC), M-seal, glass putty, hinges, handle, tower bolt, aldrop,stopper, cement, white cement, sand other similar minor accessories required to complete the jobs/complaints shall be provided by the contractor without any extra cost to the department and cost there of shall deemed to be included in quoted rates by the contractor against respective item of schedule 'A'.

Day to day maintenance for Complaint related to cement works like repair to floors/ wall plaster in patches/ filling of holes, tiles repairs etc. by deploying mason and mazdoor. Note : Five (05) compliants resolved = One (01) Job work. Note : (a) The complaints related to carpenter works, plumbing works, cement works and welding works against serial item Nos 199 to 202 shall be completed in 48 hours time after lodging/ receipt of complaints. Contractor shall ensure that all the complaints shall be attended and completed within above prescribed schedule/ time period, failing which, a penalty at the rate of double the quoted rate for that particular trade work/complaint per day till the satisfactorily completion of complaint shall be levied on the contractor and recovery for the same shall be affected from contractor's dues. (b) Complaint slip and complaint register etc. shall be provided by the contractor without any extra cost to the department and cost there of shall be deemed to be included in quoted rates by the contractor against respective items. (c) Necessary transportations, tools, plants, ladders, including nails, screws, PVC washers, brass spindle, for bib taps/ stop cocks/ pillar cocks, cotton thread, Jumper valves, white lead, flush washers, internal fitting of low level flushing cistern, nipple, tee, elbow, plug, socket, reducer (GI/UPVC), M-seal, glass putty, hinges, handle, tower bolt, aldrop,stopper, cement, white cement, sand other similar minor accessories required to complete the jobs/complaints shall be provided by the contractor without any extra cost to the department and cost there of shall deemed to be included in quoted rates by the contractor against respective item of schedule 'A'.

Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings i.e removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made for conditions separately ) and including making good the disturbed surfaces to match with existing surface and colour shade with putty for smooth finishing without andulations complete all as specified and directed.Note:- All old unsv credit materials should be deposited in MES yard day wise after completed of the job, the same material will be issued to contractor through gate pass as schedule of credit against after completion of the work.

Material and labour for cutting chasing,pinning of brick/ stone/concrete wall at any height wall cutting and chases for concealed wiring for 20/25 mm PVC conduit dia pipe,water tubing,etc and making good to facings where required and pointing in cement motor 1:3 to ends or edges of landigs,wall surfaces etc,cutting not exc 10 cm girth and including making good the disturbed surfaces to match with existing surface and colour shade with proper putty for smooth finishing with existing wall complete all as specified and directed

M&L for point wiring using approved colour coding incl providing circuit wiring with 1.5 sqmm PVC insulated, FRLSH type, ISI marked,conf to IS-694/1990 unsheathed, multistranded, single core, copper cable 1100 volts grade cables drawn through PVC Conduit 20/25 mm dia medium grade(MMS) at any height and all accessories are concealed in walls / roofs / floors / ceiling etc. flush mounting modular MS box made out of 1.60mm thick suitable for modular top cover and frame for fixing of modular switches,sockets,fan regulators, blank plate etc and including 1.5 Sqmm PVC insulated multistranded FRLSH type unsheathed(Green colour),single core cable with copper cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade with necessary putty for smooth finishing complete all as specified and directed for One light point controlled by one switch.

M&L for point wiring using approved colour coding incl providing circuit wiring with 1.5 sqmm PVC insulated, FRLSH type, ISI marked,conf to IS-694/1990 unsheathed, multistranded, single core, copper cable 1100 volts grade cables drawn through PVC casing caping 20/25 mm dia medium grade(MMS) at any height and all accessories are concealed in walls / roofs / floors / ceiling etc. flush mounting modular MS box made out of 1.60mm thick suitable for modular top cover and frame for fixing of modular switches,sockets,fan regulators, blank plate etc and including 1.5 Sqmm PVC insulated multistranded FRLSH type unsheathed(Green colour),single core cable with copper cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade with necessary putty for smooth finishing complete all as specified and directed for One light point controlled by on switch

Supply & fixing modular type switch 10 Amps, single pole,1way,1 module,240V,AC, ISI Marked and including removing old unserviceable item complete all as specified and directed.

Supply & fix ceiling rose, 3 terminal ,PVC/polycarbonate body ISI marked, and including removing old unserviceable item complete all as specified and directed.

M & L for sub main wiring with approved colour coding as per IS complete with 2 run of 1.5 sqmm single core copper conductor cable 1100 volts grade, ISI marked,FRLSH type,conf to IS-694/1990 as amended, PVC insulated, unsheathed,flexible,multi stranded copper cables drawn through and including rigid PVC conduit ISI marked medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc at concealed in wall/roofs/floors and including one run of 1.5 sqmm single core copper cable 1100 volts grade, ISI marked,FRLSH type,as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade and complete all as specified and directed. Note : - Two run of 1.5 sqmm single core copper conductor cable and one run of 6 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit.

M & L for sub main wiring with approved colour coding as per IS complete with 2 run of 1.5 sqmm single core copper conductor cable 1100 volts grade, ISI marked,FRLSH type,conf to IS-694/1990 as amended, PVC insulated, unsheathed,flexible,multi stranded copper cables drawn through and including rigid PVC casing capig ISI marked medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc at surface in wall/roofs/floors and including one run of 1.5 sqmm single core copper cable 1100 volts grade, ISI marked,FRLSH type,as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade and complete all as specified and directed. Note : - Two run of 1.5 sqmm single core copper conductor cable and one run of 6 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit.

Supply and fix copper conductor cable, PVC insulated, sheathed,flexible, multistranded,ISI marked, 1100 volts grade 3 core ;1.0 sqmm and including electric connection from switch board to connector/ceiling rose and including removing old unserviceable item complete all as specified and directed.

Supply and fix copper conductor cable, PVC insulated, sheathed,flexible, multistranded,ISI marked, 1100 volts grade 3 core ;1.5 sqmm and including electric connection from switch board to connector/ceiling rose and including removing old unserviceable item complete all as specified and directed.

Supply and fix copper conductor cable, PVC insulated, sheathed,flexible, multistranded,ISI marked, 1100 volts grade 3 core ;2.5 sqmm and including electric connection from switch board to connector/ceiling rose and including removing old unserviceable item complete all as specified and directed.

S&F for PVC non-metalic rigid conduit incl boxes,junctions boxes 1 to 4 way & terminals but incl of all tees,bends,elbows,reducers,bell mouth tube ends and fixing accessories such as couplers lock nuts,saddles,pipes hookes etc ISI marked heavy duty of size 20/25 mm dia for electrical wire,LAN,telephone and TV connections cables including cutting,chasses and laying in trenches as per site requirement and making good disturbed surfaces to match with existing surfaces with plaster/putty and including removing of old unserviceable item complete all as specified and directed.

Supply and fix LED wall mounted secruity light fitting of capacity 25 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 6 KV inbuilt surge protector and cable connection from ceiling rose/looping box/switch board/DBs to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fix LED wall mounted secruity light fitting of capacity 30 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 6KV inbuilt surge protector and cable connection from ceiling rose/looping box/switch board/DBs to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fix LED secruity light fitting of capacity 40 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 6 KV inbuilt surge protector and cable connection from ceiling rose/looping box/switch board/DBs to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.Make:- Make:- Crompton cat ref No.LSTS-40-CDL-M/Havells cat No.ENDURASUNDOWNSL40WLED765PASYBOPC/HPL Cat No.HPLLEDSL4060AE or equivalent make in Philips as approved

Supply and fix LED secruity light fitting of capacity 45 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 6 KV inbuilt surge protector and cable connection from ceiling rose/looping box/switch board/DBs to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fix LED secruity light fitting of capacity 60 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65/66 protection with 6 KV inbuilt surge protector and cable connection from ceiling rose/looping box/switch board/DBs to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fix LED secruity light fitting of capacity 70/72 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65/66 protection with 6 KV inbuilt surge protector and cable connection from ceiling rose/looping box/switch board/DBs to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fix LED secruity light fitting of capacity 90 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65/66 protection with 6 KV inbuilt surge protector and cable connection from ceiling rose/looping box/switch board/DBs to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fix 10/12watts LED bollard light fittings with made in die cost aluminium spigot complete fitiing,robust design and efficiency 360 degree lighting distribution,twister type ,IP65 protection and providing suitable fixing arrangements such as necessary civil work, nuts,bolts and washers grouting in PCC foundation and incl removing old unsv item complete all as spfd and directed.

Supply and fixed flexible LED strips trica AC LED tricolor strip light, 20/24 watt 6000k ,240Volts,IP-65 standard length ,single phase with uniform light distribution and long lasting adhesive for perfect cove light,colour as per required and including all connected accessories suitable for proper fixing on pole,wall surface,steel structures etc as per site requirement and removing old unserviceable fitting complete all as specified and directed.

Supply and fixed flexible neo LED strips 24 watt 6000k ,240Volts ,standard length ,single phase with uniform light distribution and long lasting adhesive for perfect cove light,colour as per required and including all connected accessories suitable for proper fixing as per site requirement and removing old unserviceable fitting complete all as specified and directed.

Supply and fixed 80/100W, LED flood light light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 6 KV inbuilt surge protector and cable connection from looping box to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fixed 80/90W, LED floof light light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 6 KV inbuilt surge protector and cable connection from looping box to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fixed 70/72W LED flood light light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 6 KV inbuilt surge protector and cable connection from looping box to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fixed 60W, LED flood light light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 6 KV inbuilt surge protector and cable connection from looping box to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fixed 50W, LED flood light light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 6 KV inbuilt surge protector and cable connection from looping box to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fixed 30W, LED flood light light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 6 KV inbuilt surge protector and cable connection from looping box to light fitting and testing and including removing of old unserviceable item complete all as specified and directed.

Supply and fix 20 watts LED post top lantern made in cast aluminium spigot housing with decorative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements such as necessary GI pipe at post top/pillar and civil work, lugs,glands,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed.

Supply and fix 40 watts LED post top lantern made in cast aluminium spigot housing with decorative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements such as necessary GI pipe at post top/pillar and civil work, lugs,glands,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed.

Supply and fix 40 watts LED post top lantern made in cast aluminium spigot housing with decorative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements such as necessary GI pipe at post top/pillar and civil work, lugs,glands,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed.

Supply and fix 70 watts LED post top lantern made in cast aluminium spigot housing with decorative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements such as necessary GI pipe at post top/pillar and civil work, lugs,glands,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed.

Supply and fix 70 watts LED post top lantern made in cast aluminium spigot housing with decorative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements such as necessary GI pipe at post top/pillar and civil work, lugs,glands,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed.

Supply and fix 35 watts LED post top lantern made in cast aluminium spigot housing with decorative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements such as necessary GI pipe at post top/pillar and civil work, lugs,glands,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed.

Supply and fix 45 watts LED post top lantern made in cast aluminium spigot housing with decorative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements such as necessary GI pipe at post top/pillar and civil work, lugs,glands,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed.

Supply and fix 25 watts LED post top lantern made in cast aluminium spigot housing with decorative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements such as necessary GI pipe at post top/pillar and civil work, lugs,glands,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed.

Supply and fix 20 watts LED post top lantern made in cast aluminium spigot housing with decorative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements such as necessary GI pipe at post top/pillar and civil work, lugs,glands,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed.

Supply and fix 15 watts LED post top lantern made in cast aluminium spigot housing with decorative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements such as necessary GI pipe at post top/pillar and civil work, lugs,glands,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed.

Supply and fixing 70 watts highbay down lights environmental friendly,energy saving long life corrosion resistant,vertical surface mounting pressure die-cast aluminium housig(light engine) well glass luminaires with high power LEDs aslight sources and IP65 protectio and including removing old unserviceable item complete all as specified and directed.

Supply and fixing BUDZ SOLAR LED Bollard 1w light with built-in-Solar panel LED light and lithium battery with charge cotroller IP 65 and including providing necessary fixing arrangements and incl nuts, bolts and washers etc complete fixing arrangements complete all as specified and directed.

Supply and fixing VILLA SOLAR LED gate light 1w with built-in-Solar panel LED light and lithium battery with charge cotroller IP 65 and including providing necessary fixing arrangements and incl nuts, bolts and washers etc complete fixing arrangements complete all as specified and directed.

Supply and fix GI bracket pipe of size 25 mm dia medium grade of 1.2 mtr long bent to shape suitable degree of bending as per site requirement with hot or cold bending method of process for making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixed on wall surfaces and including providing suitable fabricate galvanised flat iron clamps of 30X6 mm thick -02 Nos suitable for fixing at any place/height with hole fastners,nuts,bolts & washers including grouting on wall etc and including removing of old unserviceable item complete all as specified and directed.

Supply and fix GI bracket pipe of size 32 mm dia medium grade of 1.2 mtr long bent to shape suitable degree of bending as per site requirement with hot or cold bending method of process for making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixed on wall surfaces and including providing suitable fabricate galvanised flat iron clamps of 30X6 mm thick -02 Nos suitable for fixing at any place/height with hole fastners,nuts,bolts & washers including grouting on wall etc and including removing of old unserviceable item complete all as specified and directed.

Supply and fixed metal flush box 1/2 module, ISI marked,and suitable for existing type as per site requirement and including removing old unserviceable item from existing loaction complete all as specified and as directed.

Supply and fixed metal/PVC flush box 3 module ,ISI marked, and suitable for existing type as per site requirement and including removing old unserviceable item from existing loaction complete all as specified and as directed.

Supply and fixed metal/PVC flush box 4/5 module, ISI marked,and suitable for existing type as per site requirement and including removing old unserviceable item from existing loaction complete all as specified and as directed.

Supply and fixed metal/PVC flush box 6 module,1.60mm thikness ,ISI marked and suitable for existing type as per site requirement and including removing old unserviceable item from existing loaction complete all as specified and as directed.

Supply and fixed metal/PVC flush box 8 module,1.60mm thikness ,ISI marked and suitable for existing type as per site requirement and including removing old unserviceable item from existing loaction complete all as specified and as directed.

Supply and fixed modular white cover plate with frame 1 module ,ISI marked and suitable for existing type as per site requirement and incl screws,washears etc and including removing old unserviceable item from existing loaction complete all as specified and as directed.

Supply and fixed modular white cover plate with frame 2 module ,ISI marked and suitable for existing type as per site requirement and incl screws,washears etc and including removing old unserviceable item from existing loaction complete all as specified and as directed.

Supply and fixed modular white cover plate with frame 3 module ,ISI marked and suitable for existing type as per site requirement and incl screws,washears etc and including removing old unserviceable item from existing loaction complete all as specified and as directed.

Supply and fixed modular white cover plate with frame 4 module ,ISI marked and suitable for existing type as per site requirement and incl screws,washears etc and including removing old unserviceable item from existing loaction complete all as specified and as directed.

Supply and fixed modular white cover plate with frame 6 module ,ISI marked and suitable for existing type as per site requirement and incl screws,washears etc and including removing old unserviceable item from existing loaction complete all as specified and as directed.

Supply and fixed modular white cover plate with frame 8 module ,ISI marked and suitable for existing type as per site requirement and incl screws,washears etc and including removing old unserviceable item from existing loaction complete all as specified and as directed.

Supply and fixed switch piano type, 6 Amps, flush mounted,1 way, 240 volts,ISI marked and including removing old unserviceable item complete all as specified and directed.

Supply and fixed modular switch 1 way,10Amps,1module,240V, ISI Marked, and suitable for existing type as per site requirement and including removing old usnv items complete all as specified and directed.

Excavation in trenches , not exceeding 1.5 mtr wide and not exc 1.5 mtr depth for laying of cables, pipe lines, protection pipes and foundations etc and getting out in soft /loose soil complete all as specified and directed.

Returning filling in soil including spreading leveling watering and well rammimg in layer n exc 25 cm complete all as specified and directed

Removing excavated soil not exc 50 mtr ant depositing where directed at a level not exc 1.5 mtr above the starting point all as specified and directed

Material and labour for PCC 1:4:8 type D2 using (40 mm graded stone aggregate) for making good of road cutting portion, mass concrete, filling of foundations etc including necessary use and waste of form work complete all as specified and directed

Material and labour for PCC 1:3:6 type C2 using (40 mm graded stone aggregate) for making good of road cutting portion mass concrete, filling of foundations etc including necessary use and waste of form work complete all as specified and directed

Material and labour for PCC 1:2:4 type B1 using (20 mm graded stone aggregate) for making foundation/base plinth and pole coping, foundation etc including necessary use and waste of form work complete all as specified and directed.

Demolition of bricks or stone/boulders masonry built in cement motor including all quoins,arches,pillars etc complete all as specified and directed.

M&L for old size brick work with fly ash bricks straight or curved on plan exc 6m mean radius in CM 1:6 complete all as specified and directed.

M&L for rendering 15mm thick on fair face of brick works in CM 1:6 finished even and smooth with out using extra cement complete all as specified and directed.

M&L for preparation of new plastered surface of walls or concrete and applying two coats of oil bounded distemper over a coat of primer complete all as specified and directed

M&L for preparation of old decorated surface of wall and apply two coats of white wash complete all as specified and directed

M&L for applying two coats of oil bound distember on wall or concrete over a coat of primer on prepared surfaces including,rubbing with sand paper after complete removal of existing treatment complete

Material and labour for PVC insulated,LT armoured electric cable with aluminium standed conductor 1100 volts grade,cross-sectional area 6 sqmm ,2 core laid in trenches/pipes/ducts/wall/boarings with necessary cable lugs and glands,nuts,bolts and washers,saddeling on wall properly etc and testing and including removing old unsv UG cables complete all as specified and directed.

Boaring holes horizontally under road without damaging the surface of road (minimum 1.0 Mtr bellow the road surface) with the help of GI tubing of any dia not exc 80mm dia for passing of UG cable all as specified and as directed.

Material & labour for GI pipe 80 mm " light grade'' laid in trenches floors/on,pole/road for cable protection with all fittings complete all as specified and directed.

Supply and filling in and speading unwashed river sand for cushioning and covering the under ground cables in trenches and punning to provide required cover complete all as specified in SSR Part-I and as directed.

M & L for brick sub class 'B' 250mm x 115mm x 0.75mm and laid in trenches as in protection of UG cable complete all as specified and directed.

Material & labour for GI pipe 50 mm "light grade" laid in trenches floors/on , pole/road for cable protection with all fittings complete all as specified and directed.Make:- Jindal/Tata/swastik/BST

P JAGANNADHARAJU (BID ID -3446355)

M/s Bapujee Builders and Traders (BID ID -3446876)

M/s M M Engineering Systems (BID ID -3446899)

TECHNO SOFT SOLUTIONS (BID ID -3446490)

M/S. KISHAN ENGINEERING (BID ID -3445469)

R J ENTERPRISES (BID ID -3446916)