SPECIAL REPAIR TO BLDG NO P-228 (ORs MD ACCN) OF PRATAP LINE AND BLDG NO P-7 OF 40MVH CL-III UNDER ZONE-I AREA AT JAIPUR MIL STN

Amount

Taking down chowkats or frames with shutters not exceeding 1.50 Sqm each (without taking off shutters from the frames).etc complete all as specified and directed.

Taking down shutters exceeding 1.5 sqm but not exceeding 4.00 sqm each (without taking off shutters from the frames).etc complete all as specified and directed.

Taking down Shutters of any description exceeding 1 sqm and not exceeding 2.00 each.etc complete all as specified and directed.

S & F rolled mild steel framed work as in doors or gates of angle or other section with gusset plates rails, braces etc. complete, drilled for fixing or steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hook and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe -290 ( Gde-E-165 ).

S&F of solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, fixing in opening complete all as specified and directed.

S&F in the frames at site factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified SSR 2010 (Part-II) and Particular specification.etc complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting any gauge, thickness, of any pattern roof.etc complete all as specified and directed.

S&F pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/ cladding to wall, fixed with self tapping screws. etc complete all as specified and directed.

S&F pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/ cladding to wall, fixed with self tapping screws. etc complete all as specified and directed.

S&F MS hand rails, half round or other stock section or core for wooden hand - rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc; wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165.

S & F rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors ; fixed with angle cleats or other connecting plates Fe -290 ( Gde-E-165 ).

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to I.S. 1161-1979 grade St-240 etc complete all as specified and directed.

S & F mild steel screw bolts (machine made ) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut length of bolt exceeding 5cm but not exceeding 10 cm long (diameter of neck 11 mm to 15 mm).

M&L sheet glass, ordinary quality and glazing with oil putty/beads fixed with metal panel pin in square not exceeding 0.5sq.m in each pane. thickness in 3mm etc complete all as specified and directed.

S&F of 35 mm thick 2nd class hardwood (hollock) factory made plain framed, panelled shutters (two No. of panels) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces size of members as per IS 1003 Part-I, kiln seasoned and chemically pressure treated. The shutter shall be fitted to chowkhat as directed by Engineer-in-Charge.

S&F of 35 mm thick 2nd class hardwood (hollock) factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) complete. The shutter shall be fitted to chowkhat as directed by Engineer-in-Charge.

S&F pressed steel factory made cupboard shutter with frame of 1.25mm thick and shutter 1mm thick PBI sheet with 6 Nos 3.15mm thick and 100mm long steel hinges Godrej pattern locking arrangement including 12mm dia vertical rod. Shutters shall be spray painted in factory (total width including frame shall be measured and paid) including taking down of existing one etc complete all as specified and directed.

S&F factory made steel ventilator with top hung shutter including hinges, steel peg stay and handle complete all as specified & directed.

S&F steel window with side hung shutters factory made including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded including taking down old one etc complete all as specified and directed.

S&F steel window with side hung shutters factory made including box type hinges with steel handle and steel peg stay complete without glazing bars dovetailed or welded including taking down old one. (Note: Mild steel wire cloth shall be measured and paid separately under respective items)

S&F butt hinges of size 100mm medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F in repair butt hinges of size 100mm medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F mild steel barrel tower bolts, stove enamelled black with bright bolt and fixed length of bolt 150mm etc complete all as specified and directed.

S&F in repair mild steel barrel tower bolts, stove enamelled black with bright bolt and fixed length of bolt 150mm etc complete all as specified and directed.

S&F mild steel pressed handles, ovel type, stove enamelled black and fixed size of handle 150mm etc complete all as specified and directed.

S&F in repair mild steel pressed handles, ovel type, stove enamelled black and fixed size of handle 150mm etc complete all as specified and directed.

M&L mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed .Length of bolt 300mm etc complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 75mm double pin and rubber shoe etc complete all as specified and directed.

S&F mild steel tee hinges, stove enamelled black, medium type and fixed length 150mm. etc complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples etc complete all as specified and directed.

S & F for galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples. etc complete all as specified and directed.

M&L preparing new wooden surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and directed.

M&L preparing new steel surfaces of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zink chrome etc complete all as specified and directed.

Roughening surfaces of old concrete floor by picking,sweeping clean and washing down with water to remove dust,etc. complete all as specified and directed.

Demolition of stone slabs/wall tiles and terrazzo dado on walls tiles including floor,hearth or wall tiling including cement mortar bedding(but not backing) of any description or thickness laid bedded and pointed in any mortar in floors, aprons, removing serviceable tiles to store and rubbish off the premises.etc. complete all as specified and directed.

M&L Non skid ceramic tiles(coloured) 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set over 15mm thick screed in CM 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Non skid joint free ceramic tiles (coloured) 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set over 15mm thick screed in CM 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Glazed ceramic coloured tiles any size 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps ,wall etc set over 10 mm thick cement plaster on stone masonry surface or surface other than fair face of brick work in CM 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

M&L Non Skid joint free ceramic tiles (coloured) 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in vertical surfaces such as skirtings,dados and riser to Steps etc. set over 10mm thick rendering on stone masonary surface or surface other than fair face of brick work in CM 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Forming construction joints 30mm deep x 10mm wide filled with sealing compound Grade 'A'. complete all as specified and directed.

M/L machine cut Kota stone slab flooring 20-25 mm thick as in cooking platform, treads of steps and similar works in single piece not exceeding 1.5m in length laid over 15 mm thick cement screed base laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & as directed.

M/L Kota Stone Slab 20-25 mm thick as in cupboard shelves and similar works in single piece not exceeding 1.5m in length including rubbing and polishing complete all as specified & as directed.

Rounding to edges of stone slabs (Kota / Granite) one edges such as in steps, cooking platform and other similar situations complete all as specified & as directed.

M/L machine cut Kota stone slab flooring 20-25 mm thick ,size of kota stone 450X450mm over 20 mm thick cement screed bed laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & as directed.

M/L machine cut Kota stone slab on vertical surface of wall,riser etc in single piece not exceeding 1.5m in length 20-25 mm thick over 10 mm thick laid in cement mortar (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & as directed.

M&L 75mm thick cement concrete in foundations, filling and mass concrete type D2, (1:4:8) using 40 mm graded aggregate. etc complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block, 60mm thickness, M-35 grade of any shape and size confirming to IS-15658-2006, with grey cement and pigment laid over and including 25mm thick coarse sand laid over and including 25mm thick sand cushion layer sub base as specified and directed.

M&L Pre-cast cement concrete blocks or slab 150mm thick (1:2:4) type B-1 using 20mm graded stone aggregate with plain or interlocking joints in cement mortar (1:6) etc complete all as per specified and directed.

M&L plain cement concrete type C-1 (1:3:6) using 20mm graded stone aggregates as in plinth protections 75 mm thick finished even and fair with joints 10mm wide and in full depth at corners and at the rate 3 metres filled with mastic mortar. etc complete all as per specified and directed.

M&L plain cement concrete type B-1 (1:2:4) using 20mm graded stone aggregates as in floors, paving and roof top covering of 40 mm thick finished even and fair without using extra cement etc complete all as specified and directed.

M&L plain cement concrete type B-1 (1:2:4) using 20mm graded stone aggregates as in flooring and ramp of 100 mm thick finished even and fair without using extra cement etc complete all as specified and directed.

M&L 100 mm thick cement concrete in foundations, filling and mass concrete type D2, (1:4:8) using 40 mm graded aggregate. etc complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation etc complete all as specified and directed.

M&L for hardcore of broken stone or boulders, gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface etc complete all as specified and directed.

Taking down cement plaster or cement lime plaster on PCC/stone surface/ brick surfaces/ceiling etc. including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) on stone masonry surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on stone masonry surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) on brickwork or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) on brickwork or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in CM (1:3) on ceiling/RCC facia including finished even & smooth without using extra cement complete all as specified and directed.

M&L for GI Wire netting 0.90 mm dia and 12 mm mesh lathing to wood or metal studding, joists etc in wall ceiling stanchion etc. complete all as per specified and directed.

M&L for dubbing out average 10mm thick on irregular face or wall (when specifically ordered in writing) cement plaster (1:4) etc. complete all as per specified and directed.

Raking out joints / pointing to random rubble or polygonal rubble uncoursed or brought up to course, work built in cement mortar. etc. complete all as per specified and directed.

M&L keyed pointing to random or polygonal rubble, un coursed or brought upto courses in cement mortar (1:3). etc. complete all as per specified and directed.

M&L for preparing new plastered surfaces and applying three coats of white wash on wall etc. complete all as per specified and directed.

M&L for preparing old plastered surfaces and applying two coats of white wash on wall etc. complete all as per specified and directed.

Preparing new plastered surfaces and applying three coats of white wash on ceiling etc. complete all as per specified and directed.

M&L for preparing old plastered surfaces and applying two coats of white wash on ceiling etc. complete all as per specified and directed.

M&L for preparation of new plastered wall surfaces and applying two coat of oil emulsion distemper of any tint including over a coat of wall care putty finished smooth on plastered and other services, preparatory to distempering on wall. etc complete all as specified and directed.

M&L for washing, rubbing down and stopping of distempered surface of the walls and applying two coat of oil emulsion distemper of any tint including over a coat of wall care putty finished smooth on plastered and other services, preparatory to distempering on wall. etc complete all as specified and directed.

M&L for preparing of newly plastered surfaces of wall and and applying two coats of cement base paint .etc complete all as specified and directed.

M&L for preparing of newly plastered surfaces of wall and and applying two coats of cement base paint of any tint over a coat of primer .etc complete all as specified and directed.

M & L for complete removal of existing treatment on wall surfaces and applying two coat of cement base paint etc. complete all as specified and directed.

S/F capacity 500 Litres rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of old water tanks .etc complete all as specified & directed.

S/F in repair Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule 20mm etc complete all as specified & directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store. bore of pipe in 15mm. etc complete all as specified & directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store. bore of pipe in 20mm. etc complete all as specified & directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store. bore of pipe in 25mm. etc complete all as specified & directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) bore dia pipe in 15 mm. etc complete all as specified & directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) bore dia pipe in 20mm. etc complete all as specified & directed.

Cutting chases pinning in making good to facings if required & pointing in CM 1:3 to ends or edges or edges of landings steps, cills, sunshades shelves and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good cutting not exceeding 10 cm girth in stone concrete block or slab wall. etc complete all as specified & directed.

S&F for GI tubing medium grade with all fitting 15 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor etc complete all as specified & directed.

S&F for GI tubing medium grade with all fitting 20 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor etc complete all as specified & directed.

S&F for GI tubing medium grade with all fitting 25 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor etc complete all as specified & directed.

S & F in repairs stop valves cast copper alloy screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 20 mm bore.

S&F in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated with long shank and cup (concealed type). of pipe in 15mm. etc complete all as specified & directed.

S&F in repair angle stop valves, cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of pipe in 15mm. etc complete all as specified & directed.

S&F in repairs to bib taps/fancy type chromium plated 15mm dia cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule over etc complete all as specified & directed.

S&F in repair pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm etc complete all as specified & directed.

S&F in repair chromium plated shower roses 125mm size with swivel joints, any size, including shower arm 15mm bore size with bend of 45 degree with flange, etc complete all as specified & directed.

S&F in repairs vitreous china squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe antisyphonage pipe etc complete all as specified & directed.

S&F in repairs PVC valve less syphonic action type flushing cistern 10 litres capacity, low level white with inlet ball valve float and handle including brackets and flush pipe of polyethylene of low or high density or PVC,32mm dia suitable for low level cistern etc complete all as specified & directed.

S/F in repair Vitreous China wash basin, white, flat back, size 550x400mm but including brackets, coupling and waste pipe complete all as specified & directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm

S&F in repair tubular towel rail 20 mm dia ,D type,60 cm long between flanges with brass chromium pated bracket complete all as specified and directed.

M&L cast iron floor trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) etc.complete all as specified & directed.

S & F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf walls, or including cantilever brackets and connecting union to waste pipe; over all size 495 mm x 420 mm bowl size 410mm x 330mm x 160mm etc complete all as specified & as directed.

S&F in repair stainless steel kitchen plate rack of overall minimum size 900mm x 750mm x 225mm with partitions for small/ large plates etc made out of stainless steel 24 gauge, fixed with rawl plug and CP steel screws all as directed of approved quality complete all as specified & directed.

S&F in repair soap dish, vitreous china white, approximate size 160mm x 160mm x 90mm fixed to plugs with chromium plated brass screws etc. complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required Internal dia of pipe 100 mm etc. complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required Internal dia of pipe 75 mm etc. complete all as specified and directed.

S&F for cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors, sand cast pipes bore of pipe in 100mm. etc. complete all as specified and directed.

S&F for cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors, sand cast pipes bore of pipe in 75mm. etc. complete all as specified and directed.

S&F for cast Iron soil, waste and vent pipes, in any length with or without ears, with cement joints, but fixed to walls, sand cast pipes bore of pipe in 100mm. etc. complete all as specified and directed.

S&F for cast Iron soil, waste and vent pipes, in any length with or without ears, with cement joints, but fixed to walls, sand cast pipes bore of pipe in 75mm. etc. complete all as specified and directed.

S&F in repair cast iron cowls bore of pipe in 100mm. etc. complete all as specified and directed.

S&F in repair cast iron bends (any radius) 100mm bore, with oval access doors etc. complete all as specified and directed.

S&F in repair cast iron bends (any radius) 75mm bore, with oval access doors etc. complete all as specified and directed.

S&F in repair branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, size of bore of pipe in 100mm. etc. complete all as specified and directed.

S&F in repair stack clamps, out of 25mm by 3mm flat iron and 8mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, size of bore of pipe in 100mm. etc. complete all as specified and directed.

S&F in repair stack clamps, out of 25mm by 3mm flat iron and 8mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, size of bore of pipe in 75mm. etc. complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation, etc or for shaft, well, cesspit, manhole, pier holes etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out soft/loose soil.

Returning filling with earth obtained from excavation including spreading watering and consolidation in layers not exceeding 25 cm thick .etc complete all as specified & directed.

Removal of excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point .etc complete all as specified & directed.

S&F in repair drapery rod PVC insulated 25mm dia including fixing brackets and decorative knobs on each end of rod of approved pattern and colour etc complete all as specified & directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level), including removing out of MD Land.

Demolition of PCC in roofs, floors (other than ground floors ), beams, staircases, landing, chajjas and similar suspended work including removing out of MD land

Demolition cement concrete (unreinforced ) any description and in any position not otherwise specifically provided for cill, coping etc complete all as specified & directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified & directed.

M&L for 25mm thick cement concrete type B-0, (1:2:4) using 12.5mm graded aggregate in sub floors, sub base floors and paving. etc complete all as specified & directed.

Cutting holes in stone walls built in cement mortar or in cement lime mortar and making good dismantled portion in cement 1:3 or cement concrete 1:2:4 Type B-1 as required depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall exceeding half brick but not exceeding one brick. etc complete all as specified & directed.

M&L providing cement concrete , (1:2:4) type B1 using 20 mm graded aggregate in cill, coping, apex stone, platform for water tank on roof etc. complete all as specified & directed.

Sand stone slabs in sun shades, chajjas, shelves, cills, landings, cover stones templates, etc. not exceeding 2 m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4 ,thickness of slab is 5 cm etc complete all as specified & directed.

M&L for preparing old wooden surfaces of any description exceeding 10 cm width or girth and applying one coat of synthetic enamel paint etc complete all as specified & directed.

M&L for providing reinforced cement concrete (nominal mix) B1 type, (1:2:4) mix using 20 mm graded aggregate in slabs supported on walls, beams and columns; in floors, roofs, landings balconies, canopies, deck slabs and in shelves and the like etc complete all as specified & directed.

Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cracking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. etc complete all as specified & directed.

-Ditto- but 5mm dia and over upto and including 10 mm dia in stirrups, spacers and binders TMT bars.

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified & directed.

M&L for walling of squared rubble, regular coursed, well bounded, bedded and solidly hearted, built in cement mortar 1:4. etc complete all as specified & directed.

M&L brick work with subclass ‘B’ old size bricks straight or curved on plan exceeding 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified & directed.

M&L brick work with sub-class “B” bricks , straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 etc complete all as specified & directed.

M&L applied a coat of bituminous primer confirming to [email protected] Kg per Sqm ,and aproviding APP BASED POLYMERIC Membrane not less than 3 mm thick. Weighing not less than 3 Kg/m2, reinforced with polyester non woven fabric(weighing not less than 15 Gm/Sqm) shall be laid dry torch application, side overlaps shall be 75 mm and end slab shall be 100 mm and all over laps and joints shall also be sealed by torch application. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside the parapet groove. This shall be finished by a membrane flashing all as directed and screed bed or bedding layer or mortar 15mm thick in cement mortar 1:4 with WPC on roof surfaces and 30mm padding in PCC (1:2:4) type B-0 using 12.5mm size graded stone aggregate, laid to provide a finished slope of 1:30 finished even and smooth without using extra cement including taking down cement plaster on roof surfaces, cleaning and removing rubbish including roof treatment etc. complete all as specified and directed.

M & L for cutting out cracks to V-section in existing roofs or terracing cleaning out wetting grouting with cement and sand slurry 1:3 etc complete all as specified & directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors ), beams, staircases, landing, chajjas and similar suspended work including removing out of MD land

M&L providing cement concrete (1:2:4) type B1 using 20mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered on edges etc complete all as specified & directed.

M&L for marble crazy over 20mm the screed in CM 1:4 shall be laid over surface obtained after fine sand dusting. When the cement is still gree, 18-20 mm thick marble crazy pieces shall be spread in regular panel using dividers of marble strips 18-20 mm thick and 50 mm wide the size of panels shall be 1.0 to 1.50 m in length an breadth spread over the entire roof area so that 80-85% area of roof is covered by these pieces leaving joints 10 to 15mm vide the space for joints shall be filled with cement sands and marble aggregate of 4 to 7 mm size like in "cast in situ tarrazo topping" the work of placing curing and grinding shall be done all as per clause 13.38.4 to 13.38.6 of SSR Part-I.

M&L for preparation of APP based polymeric surface and appling two coats of aluminium paint etc complete all as specified & directed.

S&F in repair 18mm thick MDF board of approved colour for modular shutters, boxes drawer including stainless steel poppet hinges, handles, sliding roller with channel etc complete all as specified & directed.

M&L for cutting grooves in brick wall 75mm wide and 65mm deep and shaping horizontally face of groove with cement mortar 1:3. etc complete all as specified & directed.

M&L for rendering 15mm thick in CM (1:3) on fair faces of brickwork or concrete surfaces with water proofing compound @3% by weight including finished even & smooth without using extra cement etc complete all as specified & directed.

M&L for cement concrete type E2, (1:5:10) using 40 mm graded stone aggregate in foundations, filling and mass- concrete etc complete all as specified & directed.

Supply only Integral water proofing compound.

Carefully demolition of cement concrete reinforced by chisel( reinforcement cut as required to facilitate demolition) in roofs, floors (other than ground floors ), beams, staircases, landing, chajjas and similar suspended work including removing out of MD land

Cleaning of old rusted reinforcement for joint with new reinforcement etc complete all as specified & directed.

Welding in repairs exceeding 2.5cm but not exceeding 5.cm in length, thickness of metal to be welded exceeding 9mm but not exceeding 20mm. etc complete all as specified & directed.

M&L for reinforcement cement concrete upto 50mm thick by guniting method (concrete spray by compressor) to increase structural strength to including rendering 15mm thick in cement mortar 1:3 etc complete all as specified & directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position and cleaning and removing all scale and dirt, etc. from tanks and from mouths of circulating pipes, etc. capacity in litres exceeding 250 and not exceeding 500. etc complete all as specified & directed.

S & F Mild steel, plain, black sheet 1.25 mm thick in hearths, covering to door shutters, covering to door chowkets ( frames ), chullah hood , water tanks ,water troughs , ducts, urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched , including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. complete all as specified & directed.

S&F anodised aluminium snap grid frame work for false ceiling, size of grid 605 x 605 mm and 12 mm thick perforated particle board/ tiles 60x60 cm in size,for insulation and acoustic purposes with staples on snap grid including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60mm long and expansion hold fasteners 12.5 mm dia. 40mm long etc. complete all as specified & directed.

Taking down carefully surface aluminum or copper point wiring with PVC casing capping or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified & directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 Sq mm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 Sq mm (Green) drawn into and including concealed rigid non-metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and unwelded sunken galvanized pressed steel terminal boxes of thickness not less than 1.0 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulators as required for the following :- (Note - Cost of cutting of chases in stone/brick masonry and making good disturbed surfaces for concealing the conduit shall deemed to be included in quoted rate of point wiring).

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One socket outlet 6 amp controlled by one switch on the same board with other switches.

(d) One socket outlet 6 amp controlled by one switch on independent board.

(e) one light point controlled by two, two way switch.

(f) One bell point controlled by one bell push.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 Sq mm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 Sq mm (Green) drawn into and including concealed rigid non-metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets as required for one 16 amp socket outlet point controlled by one switch on independent board. (Note - Cost of cutting of chases in stone masonry and making good disturbed surfaces for concealing the conduit shall be deemed included in quoted rate of point wiring).

S&F angle holder, insulated polycarbonate body with back plate complete.

S&F switch piano flush button single pole one way 6 Amp complete.

S&F switch piano flush button single pole two way 6 Amp complete.

S&F switch piano flush button single pole one way 16 Amp complete.

S&F of bell push, flush type, 6 Amp 240 Volts complete

S&F of door bell, AC, 240 Volts, SP complete

S&F socket outlet 2 in 1, 3 pin 6 & 16 amp flush type complete.

S&F socket outlet 2 in 1, 2 & 3 pin, 6 amp, flush type complete.

S&F ceiling rose 6 amp, 3 plates polycarbonate body complete.

S&F hum free electronic step fan regulator 120 - 280 volts of 100 watt capacity (socket type) including connecting up complete.

M&L for sub main wiring along with earth continuity conductor with, PVC insulated FRLS multistranded copper conductor cable (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories as required for the size 2x6.0 Sq.mm + 1x6.0 Sq.mm earth wire in 20mm dia conduit including making good disturbed surfaces of wall even and smooth using cement mortar 1:3 with surface colour or paint as required.

S&F MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 43, IK-09 with reversible double door, recess mounted , having insulated 250 Amps tinned copper bus bar, 02 neutral bus bar, 02 earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required for the TPN, 415 volts, 4 ways.

S&F MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 43, IK-09 with reversible double door, recess mounted , having insulated 100 Amps tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required for the SPN, 240 volts, 8 ways.

S&F MCBs of 'C' series having breaking capacity 10KA/16KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs as required for the following :-

(a) Single pole 6 to 32 Amps

(b) Double pole 10 to 32 Amps.

(c) Four pole 63 Amps 415 Volts, breaking capacity 16KA.

S&F in repair LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 105 lumen per watt and total power consumption not more than 19 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete. Make: Philips Cat Ref No. Endura Next Batten "BN 108C LED 20S PSU CDL WH" or equivalent in CG/ Bajaj/Panasonic/ Havells.

S&F in repairs LED bulk head fitting 9 watt IP 66 & IK 09 with pressure die cast aluminium housing & polycarbonate diffuser duly pre wired connection with 0.75 Sq.mm PVC insulated & sheathed three core flexible multi stranded copper conductor cable. Make:- Philips Cat Ref No. WT 202W LED 6S PSU S2 PC or equivalent in Panasonic/Havells/CG/Bajaj as approved.

S&F in repairs energy efficient recessed mounted LED luminaries suitable for 2’x2’ grid ceiling with flat diffuser and lumen output of 3300 lumens having constant current electronic driver duly connected with 0.5 sq.mm white colour PVC insulated & sheathed three core flexible multi stranded copper conductor cable as required. Make-Philips cat ref No RC365B LED33-6500 PSU OD WH or equivalent in CG/Havells as approved.

M&L for earthing with galvanized steel earth plate electrode 600mmx 600mmx6mm thick buried directly in ground (earth pit not less than 2.25 meter deep below normal ground level) with the top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth lead wire 4mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate No. 03 of SSR Part -I connected to earthing point and including 15mm bore light grade G.I. protection pipe (up to 7.5 meter from edge of the pit), PCC pit in mix 1:3:6 type C1 with PCC 1:2:4 type B-1, 40mm thick cover, watering arrangement with funnel and wire mesh and 20mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work including testing on completion.

Excavation in any type of soil in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out for laying LT underground cable complete all as specified & directed.

S&F steel tubes 40 mm bore light grade ISI marked with medium grade fittings for cable protection as required complete all as specified & directed.

M&L for sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete. (Note :- Punned thickness shall be measured.)

Supply and laying old size bricks, common burnt clay building bricks sub class ‘B’ designation 75 laid in trenches over sand for cable protection complete.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core including taking down complete all as specified & directed.

Taking down industrial plug and socket including one number single pole MCB any make any capacity after disconnecting complete.

Taking down MCB distribution boards with incoming and outgoing controls any make any capacity after disconnecting complete.

Taking down carefully sub main wiring with PVC casing capping/PVC surface conduit and making good disturbed surfaces complete.

Supply,installation,testing and commissioning of LT panel board fabricated out of 2mm thick stainless steel (SS 316) with copper bus bars 4 pole equal of capacity in colour code R,Y & B 200 Amps 415 Volts indoor type wall mounted of size not less than 750mmx650mmx250mm, installed on procelain insulators with bus bar chamber. The panel shall be dust and vermin proof, protection class IP 42 class, front opening & compartmental type with approach for cabloe entry and for easy maintenance duly internally wired with FRLS, PVC insulated stranded copper conductor cable of 1.0 Sqmm including LED indicator for R, Y & B and comprising of the following :- Incoming : MCCB 125Amps 4pole, 16KA 415Volts,70-100%,50 Hz -1N0 Outgoing : (a) Single phase tamper proof meter with optical port 10 to 60 Amps-04 Nos. (b) MCB Double pole 40 Amps 230 Volt-05 Nos

Schedule of Credit

M/S MAYANK ASSOCIATE

M/S M.K.Constructions

J.J.ENGINEERING

UNIVERSAL INFRAPROJECT PVT LTD

Pioneer Enterprises

Ms Hari Deva Builders

Ravi Enterprises

Smita Constructions