SPECIAL REPAIR TO BLDG NO AP 01 POWER HOUSE OF 763 SU AT AF STN ARJAN SINGH

Amount

CIVIL WORK

Removing existing damaged roof treatment including screed bed or bedding layer and removing the debrises complete all as per direction of Engr-In-Charge

Demolition of Cement Concrete (un-reinforced) of any description and in any position, not otherwise specifically provided for and removing the debrises complete all as specified and as directed.

M&L PCC 1:2:4 type BO using 12.5 mm graded aggregate as in levelling course or similar work complete all as specified and as directed.

M&L PCC 1:2:4 type BO using 12.5 mm graded aggregate as in haunching. Kerb in roof or similar work complete all as specified and as directed.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:4 on roof, with using water proofing compound as per Manu-factuerer’s Instructions, complete including ponding test for 72 Hrs all as specified and as directed. (Note : WPC will be measured and paid separately)

Apply evenly a coat of cold bitiminous primer (IS 3384) @ 0.25 Ltr/sqm including cleaning of surfaces complete all as specified and direcetd

M&L for laying through authorised/specilized agency, APP based polymeric membrane minimum weighing 3.5Kg/sqm and mimimum 3mm thick reinforced with polyster non woven fabric (weighing. not less than 160 gms/sqm) laid on primed surface by torch application complete all as specified and direcetd. The overlaps shall be minimum 100 mm on the transverse direction and 75mm on longitudinal direction.

M&L for preparing surfaces of APP and applying one coat of aluminium paint @ 0.11 Kg/Sqm over the APP complete all as specified and as directed.

Taking down cement plaster of any description of brick or stone or concrete surfaces etc including raking out joints hacking for key scrubbing down with water etc complete.

Rendering 15mm thick in cement mortar 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 20mm thick in CM (1:4) in two layers (8mm thick in CM (1:4) with approved water proofing compound as per manufacturing instraction over backing coat of 12mm thick in CM (1:4)) on brick work or concrete surfaces finished fair & even . (Note:- WPC will be measured and paid separately)

M&L for Rendering 5mm thick in Cement Mortar 1:3 on ceiling surfaces finishing even and smooth without using extra cement complete all as specified and as directed.

Rendering 15mm thick in cement mortar 1:4 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound

M&L for preparation of newly plastered surfaces of walls and apply two coat of Oil Bound Distemper over a coat of primer after applying Chalk whiting, on plastered surfaces ,preparatory to distempering including necessary preparation of surfaces complete all as specified and as directed.

Material & Labour for apply two coat of cement base paint over a coat of primer on new surfaces including preparation of surface complete all as specified and as directed

M&L for applying three coats of white washing including preparation of new or previously untreated surfaces of ceiling complete all as specified and directed.

M&L for applying one coat of white washing including preparation of old treated surfaces of ceiling complete all as specified and directed.

M&L for complete removal of existing treatment of walls and apply two coat of Oil Bound Distemper over a coat of primer after applying Chalk whiting, on plastered surfaces ,preparatory to distempering including necessary preparation of surfaces complete all as specified and as directed.

Material & Labour complete removal of existing treatment of walls and apply two coat of cement base paint over a coat of primer on new surfaces including preparation of surface complete all as specified and as directed

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for 100mm thick PCC 1:2:4, type B1 with using 20 mm graded stone aggregate as in floor finished even and smooth with using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick premium quality conforming to IS-13712, grade B-II(a) (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tile over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L 300X 300 x 7mm thick coloured glazed ceramic tiles conforming to IS-13712 grade B-III fixed as in vertical surface such as risers of steps, skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including 10 mm thick screed bed or bedding layer in CM 1:4 finished even and rough complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4, type B0 with using 12.5 mm graded stone aggregate as in floor finished rough to receioved the top layer complete all as specified and directed by Engr-in-Charge.

M&L for Kota stone slab 20-22 mm thick in riser steps skirting dado and pillar laid over cement screed 10 mm thick CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and as directed by Engr-in-Charge.

M&L PCC 1:4:8 type D2 using 40 mm graded aggregate as in foundation filling and mass concrete or similar work complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilate demolition) in ground floors and paving not exceeding 15cm thickness (below or above ground level) and disposing off the rubbish materials where directed complete all as specified and as directed by Engr-in-Charge.

Demolition of brickwork, built in cement mortar including all quions, arches, pillars etc including removing of rubishes.

Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips

M&L for Half Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) all as specified

S&F of Powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F of 12mm thick Prelaminated particle board , interior grade, prelaminated both side with decorative choice lamination , fixed with stainless steel screws to aluminium frame work complete all as specified and as directed.

S & F 4.8mm thick tinted glass, of any colour, glazing with oil putty / beads in square not exc 0.50 Sq.m in each pane, all as specified and directed.

S&F of Powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

S&F mild steel TMT bars conforming to Fe-500, 10mm dia and over, cut to length bent to shape required incl cranking bending spirally hooking ends and binding with mildsteel wire annealed not less than 0.9mm dia or securing with clips,complete all as specified and as directed by Engr-in-Charge.

S&F TMT reinforcement bar, conforming to Fe-500, 5mm dia and upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as binding with and including mild steel wire (Annealed) not less than 0.9mm dia or securing with clips all as specified.

M&L for RCC M-25 Design Mix as in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses

M&L for Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter and obtain rough finished surface.

M&L for RCC M-25 Design Mix as in chajja and the like; any thickness.

M&L for Formwork to chajja and obtain rough finished surface.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) n.exc 1.5 sqm each including taking out hold fast and making good surface of wall in CM 1:4 including painting to match with the existing all as specified & directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm but n exc 4.0 sqm each including taking out hold fast and making good surface of wall in CM 1:4 including painting to match with the existing all as specified & directed.

S&F for solid PVC door frame of size 50 mm x 47 mm made out of 5mm thick plain colour PVC sheet re-inforced with MS square tube supplied and fixing in opening incl hold fast as per specification complete all as specified and directed.

Supply and fixing Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail and bottom rail on either side & as gap insert for top rail and bottom rail.Panelling of plain colour PVC sheet to fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet Beading and joined together with solvent cement, fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F of Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete

S&F pressed steel frame of size 165x60mm, made out from 1.60mm thick cold rolled mild steel sheets for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete as specified, supplied and fixed complete.

S&F of 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and as directed.

S&F of Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed by Engr-in-Charge..

S&F of Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed by Engr-in-Charge..

M&L for mils steel works as in window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves, wind ties for roof including securing bolts etc. and similar articles conforming to Fe-290 Gde E-165 including taking down the existing one.

S & F sheet glass 3mm thick ordinary quality and glazing with oil putty / beads in square not exc 0.50 Sq.m in each pane, all as specified and directed.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples.

M &L PCC (1:2: 4) type B0 using 12.5 mm graded crushed stone aggregate as in bed plates, fixing of hold fast & filling in prssed steel door frame complete.

S&F 150 mm size aluminium anodised handles cast type all as specified & directed

S&F aluminium anodised barrel tower bolt of extruded section 150 mm length of bolt all as specified & directed

S&F aluminium alloy anodised sliding door bolt with hasp and stapple ( bolt type) and fixing clips of sheet cast or extruded section with fixing bolts and sliding bolt of extruded section, 250 mm length & dia not less than 12mm with & including 6 Nos of bolt

S&F 100 mm Butt hinges, medium weight, cold rolled mild steel, and fixed

M&L for preparation of new steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified & directed

M&L for preparation of new wooden surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified & directed

Material & Labour for preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material & Labour for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

S&F in repairs Galvanised steel water tubing 15 mm bore Medium Grade with all new fittings , fixed to walls and ceiling or laid in floors as required,complete all as specified and as directed.

S&F in repairs fancy type Bib Tap with flange 15mm bore (dia) Cast Copper Alloy, Chromium Plated with with Capstan Heads Handle, screwed down, screwed for Iron Pipe, complete all as specified and as directed.

S&F PVC (SWR) floor trap for 75mm outlet dia, plain with grating including jointing with solvent cement including taking out the existing one.

S&F PVC (SWR) 75 mm pipes single socketed in any length with rubber ring joint fixed to wall

S&F PVC (SWR) junction single, (Single T) equal or unequal with access door suitable for 75mm bore of pipe,jointing with solvent cement complete.

S&F PVC (SWR) bends of any radius with access door, 75 mm bore.

S&F PVC (SWR) 110 mm pipes single socketed in any length with rubber ring joint fixed to wall

S&F PVC (SWR) junction single, (Single T) equal or unequal with access door suitable for 110mm bore of pipe,jointing with solvent cement complete.

S&F PVC (SWR) bends of any radius with access door, 110 mm bore.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) all as specified

Excavating in Trenches, not exc. 1.50 METRE wide and not exc. 1.50 METRE in depth, for Foundation, Manhole, etc. and getting out in Soft/ Loose Soil, complete all as specified and as directed.

Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 250mm in Soft/Loose Soil, complete all as specified and as directed.

Removing excavated Materials (Soils) not exc. 50.00 METRE and depositing where directed at a level not exc. 1.50 METRE above the Starting Point in Soil, complete all as specified and as directed.

S&F Salt-glazed stoneware gully traps, square or round mouthed, tvpe 'S' of size 150 x 150mm setting and jointed with solvent cement complete all as direcred by Engr-in-Charge.

M&L Salt-Glazed Stoneware Drain Pipes of Internal dia 150mm, Grade ‘A’, laid in Trenches in Foul Condition, Jointed in Cement Mortar in CM (1:1) and Tested, complete all as specified and as directed.

M&L Cement Concrete (1:3:6) Type C1 (20mm Graded Stone Aggregate) Bed for Drain Pipes of Bore 150mm including Packing under and Haunching against the Sides of Pipes after they are laid in Foul Condition and Testing, complete all as specified and as directed.

Supply and fixing stop valve cast copper alloy, screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or union for pipe 15mm bore,fancy type,chromium plated with long shunk and cup,concealed type,

Supply and fixing pillar tap with flange, cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered Hot, or Cold with long screwed shank and fly nuts, screwed for iron pipe of 15mm bore.

M&L for PVC Connection pipe 15mm size with PTMT Nuts of length 450mm and fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China Urinal 465X355X265mm, Bowl Type (Flat Black) complete including providing and fixing Plug bedding Urinal against Wall in cement mortar 1:2, securing Urinal Plugs with 60mm long Brass Screws, pointing around Urinal Back in Cement, including Grating and Union for Discharge Pipe, Galvanised Iron 40mm dia Light Grade Discharge Pipe and fixed-in-repairs and Making Good disturbed Surfaces/ Portion with Cement Mortar 1:3, complete all as specified and as directed.

S&F Vitreous China Wash down Water Closet Pan (Pedestal Pattern) White including fixing Bolts providing Joints between Flush Pipe and Socket of WC Pan(excluding Flushing Cistern and Flushing Pipe) with Plastic Water Closet Seat, Black, Closed Pattern with Recessed Bottom and Cover including Mild Steel Chromium Plated Aluminium Hanging Device and fixed-in-repairs, including Making Good disturbed Surfaces with Cement Mortar 1:3, complete all as specified and as directed.

S&F of Chrome finished Curved shaped urinal partition with 8mm thick frosted glass of make Jaquar or equivalent.

Supply only PVC low level flushing cistern, 10 litres capacity, syphonic action type white body with inlet ball valve, float , handle, bracket, flush pipe etc complete & connecting to WC complete.

S&F Vitreous China Wash Hand Basin size 550x 400mm (Flat Back or Angle Back type) White, with 32mm dia Brass Chromium Plated Waste Fitting, Galvani-sed Iron ‘Light Grade’ 32mm bore Waste Pipe, a Pair of Cast Iron Brackets duly Painted/ Erecting Stand including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 including Taking down Unservice -able Wash Hand Basin and connected Items, complete all as specified and as directed.

Construction of Septic tank for 25 users (brick construction) complete all as shown in drawing and as directed including necessary excavation and earth work, plastring, returning filling and removing complete all as specified and shown on drawings.

Construction of soakage well for 25 users complete all as specified and directed by Engr-in -charge complete all as specified and shown on drawings.

ELECTRICAL WORKS Note : Prior to commencement of electrical works, the contractor needs to submit valid Electrical Liscence in the name of himself/themself or Aggrement with agency having valid Electrical Liscence alongwith Agency's Electrical Liscense to the Accepting Officer for his approval through GE/AGE(I). In absence of such documents, no work will be executed at site and to be treated as defaulter on the Contrctor's part . In addition, Supervisor for execution of electrical works employed by the Contractor shall posses Supervisory Certificate of competancy issued by concerned State Govt/Union Territory and the Worker/Tradesman for execution of Electrical Works must hold necessary permit issued by concerned State Govt/Union Territory.

Taking down carefully aluminium/copper point wiring (light,fan,socket or power) of any type complete, including fittings such as switches,ceiling roses,pendants,regulators sockets etc.,removing from site and making good disturbed surfaces of walls,floors,ceiling etc.,all as directed

M & L for point wiring complete with 1.5 sq mm FR,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral),drawn into and including PVC caing & caping medium grade of suitable size and accessories fixed on wall, floor, roof etc. and including provision of PVC insulated 1.5 sq mm copper conductor (Green Colour) for earth continuity and connected to common earth dolly and pressed steel terminal boxes made out of 1.6 mm thick MS sheet flush boxes concealed in wall and laminated sheet cover of 3 mm thick for housing the switches socket,outlet etc., all as specified and directed by Engineer-in-Charge for one light/fan/exhaust fan point controled by one one way 5/6 Amp switch (a) Note :- Cost of PVC casing caping, cover plate and box of suitable module, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per item No -93 here in above but for one 5 pin socket outlet 06 Amps on independent board ( but Not below the switch board of light points in the same vertical plane)

All as per item No -06 here in above but for one 5 pin socket outlet 05 Amp on same board with other switches

All as per item No 02 here-in-before but for one 15 Amps socket outlet using by 2.5 sq mm copper conductor cable (FRLS) with 2.5 sq mm PVC insulated FRLS single core copper cable for earth continuity conductor.

Supply and fix switch piano flush type ISI, 6 Amps 240 volts single pole one way(ISI).

Supply and fix in repairs switch piano flush type ISI, 6 Amps 240 volts single pole one way(ISI).

Supply and fix socket outlet, 5 pin 6 Amps, flush type.

Supply and fix switch piano flush type ISI, 15 Amps 240 volts single pole one way(ISI).

Supply and fix in repairs switch piano flush type ISI, 15 Amps 240 volts single pole one way(ISI).

Supply and fix Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type

Supply and fix in repairs Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type

Supply & fix ceiling rose, 2 to 3 terminals, surface bakelite fixed to wall/ceiling all as directed by Engineer-in-Charge

Supply & fixing ceiling fan regulator,electronic type,step type 5 variable speed AC, 230 volts all as directed by Engineer-in-Charge

Supply and draw submain wiring with two single core 4.00 sqmm FR PVC insulated copper cable 1100 vots grade multistrand, unsheathed conductor drawn into concealed conduit including 4.00 sqmm multi strand FR PVC insulated copper wire for earth continuty conductor connected to common earth dolly complete including taking down old unserviceable sub main wiring including conduit of any size and making good disturbed surface complete all as specified and directed. NOTE (i) PVC/steel conduit incl accessories and cutting chasses shall be measured separately under respective items mentioned here-in-after. (ii) 2 Run of line conductor and 1 Run of earth continuity conductor shall be measured as one unit length.

Supply and draw submain wiring with two single core 2.50 sqmm FR PVC insulated copper cable 1100 vots grade multistrand, unsheathed conductor drawn into concealed conduit including 2.50 sqmm multi strand FR PVC insulated copper wire for earth continuty conductor connected to common earth dolly complete including taking down old unserviceable sub main wiring including conduit of any size and making good disturbed surface complete all as specified and directed. NOTE (i) PVC/steel conduit incl accessories and cutting chasses shall be measured separately under respective items mentioned here-in-after. (ii) 2 Run of line conductor and 1 Run of earth continuity conductor shall be measured as one unit length.

M & L for Cutting chasing, pinning for concealed sub main wiring wiring not exceeding 10 cm girth in brick wall including making good to facing where required and pointing in cement mortar 1:3 complete all as specified and directed.

M & L for Rigid non-metallic PVC conduit(medium) (for Sub main wiring) with all fittings like Tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxes etc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. of nominal size 25 mm complete all as specified and directed.

S & F single pole and neutral DB wall mounting type, 240 volts, 8 way with 100 Amps rated bus bar, double door (Metal), IP-43 and IK 09 suitable for fixing MCBs including connection etc. complete all as directed. Make L&T / Siemens/ABB/Legrand

S & F Tripple pole and neutral DB wall mounting type, 240 volts,4 way with 100 Amps rated bus bar, double door(Metal), IP-43 and IK 09 suitable for fixing MCBs including connection etc. complete all as directed. Make L&T / Siemens/ABB/Legrand

S & F MCB SPN/DP, 6 to 32 Amps, 240 volts, "C' Curve of Make L&T / Siemens/ABB/Legrand

S & F MCB SPN/DP, 40 Amps, 240 volts, "C' Curve of Make L&T / Siemens/ABB/Legrand

S & F MCB TPN/FP, 63 Amps, 240 volts, "C' Curve of Make L&T / Siemens/ABB/Legrand

S&F LED batten with LED tube light 18 watt, 230 Volts Energy efficient surface mounted luminaire , Pre-wired with high efficiency electronic driver, connecting up with twin core twisted flexible copper conductor cable with suitable size. Make Century (Magic) /Philips/Bajaj

Supply & fixed lamp holder , PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings complete all as specified.

S&F of single pole 16 amps flame proof rotary switch with cable termination box in LM 6 Make Sudhir or as approved by GE

S&F LED Bldg security/street luminaire 35 W/36 W Aluminium PDC housing, toughened glass cover, not less than IP 65 protection with Surge Protection 5kv , pre-wired , connecting up with twin core twisted flexible copper conductor cable with suitable size including taking down the existing light fittings. Make Century (Magic) /Philips/Bajaj

Taking down Exhaust Fan of 450/600mm Sweep by disconnecting Electric Connection, dismantling Blades, louvers and removing to MES STORE YARD OF AGE E/M (AF) PANAGARH for Check-ing, greasing. oiling and including preparing Surfaces of Exhaust Fan of any Sweep and Make, complete Body, Blade, , Cleaning Dust, Dirts, etc. filling Cavities with Filler and applying Two Coat DUCO Paint with Spray Machine including Writing MES No. in Black Paint, complete all as specified and as directed including fixing of exhaust Fan in same position/hole after repair and assemble of parts, connecting up with and including of Flexible Copper 3 Core Wire of 2.50 Sqmm, from Ceiling Rose/Connector to exhaust Fan, complete all as specified and as directed. all as specified and as directed.

M&L for Opening Stator of exhaust Fan 450/600mm Sweep Cleaning of Parts, replacement of Unserviceable Parts as ordered, Greasing of Moveable Parts, Taking out burnt Coil, Cleaning the Segments complete and Re-winding the Same with Supper Enameled Copper Wire of same Gauge and same Weight with Insulation Paper, Varnishing and Heating, Re-assemble the same after repaired and Testing, complete all as specified and as directed. Note : Cost of transportation from site to workshop is deemed to included in the quoted rates.

M&L for security light bracket made out of GI tubing medium grade upto 1.5 mtr long 40 mm dia including bending, welding as required and making holes including provision of flat iron clamps 50x 6 mm thick (02 Nos) with nut, bolts and washers suitable for fixing on steel tubular poles/PCC poles including taking out of old unserviceable bracket complete all as specified and as directed.

Note The Scope of Work contained Sch of Credit amounting to Rs. 11626.00 (refer Tender Srl Page No 21) . The Quoted sum shall be arrived at after deducting amount of “Sch of Credit” from the total amount of the ‘BOQ’

M/S SWAPAN KUMAR MONDAL

ANSH CONSTRUCTION

M/s RAJEN ROY