REPAIRS TO WOODEN JOINERY, PARTITION/PANELLING, CUPBOARD ETC.REPAIRS/ REPLACEMENT OF WPC DOORS, PVC DOORS, TOUGHEN GLASS DOORS AND ALUMINIUM JOINERY/PARTITION WORKS ETC IN OTHER THAN HOSPITAL BUILDING AT INHS ASVINI UNDER AGE(I) ASVINI.

Amount

Taking down chowkat with shutters (without taking off shutters from the frames) area n.exc 1.5 Sqm each

Taking down chowkat with shutters (without taking off shutters from the frames) area exc 1.5 Sqm but n.exc 4 Sqm each.

Taking down shutter of any description area exc 1 Sqm and n.exc 2 Sqm each.

Taking down partition wall of any description other than brick work of any size complete all as secified and directed by Engr-in-charge.

M&L for second class hardwood (SAL) plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified.

M & L for MS work as in holdfast and similar articles conforming to grade Fe 410-0 and Fe 310-0 complete all as specified

M&L for 30 mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified.

M&L for 35 mm thick second class hard wood (Sal) glazed and skeleton shutters open rebated and prepared to receive glass, gauze, (without sash bars) edges of framing plain chamfered or rounded fitted to cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I Section 8 Clause 8.20 (b) complete all as specified. Note:- Glazing and aluminium wire mesh shall be measured and paid separately

S&F 30 mm thick 2nd class hard wood (Sal) plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), including decorative designed mouldings complete all as directed by Engineer-in-Charge.

Supply and fix 3.mm thick sheet glass ordinary quality and glazing with oil putty in square or fixed with beads, n. exc 0.5 Sqm in each pane

Supply and fix 4.8 mm thick sheet glass ordinary quality and glazing with oil putty in square or fixed with beads, exc 0.5 Sqm in each pane including hacking out the old glass pane complete all as specified and directed by Engr-in-charge.

S&F 4.80mm thick sheet glass ordinary quality and glazing with aluminium beading and rubber beading in square n exc 0.50 sqm in each pane complete all as specified and directed by Engr-in-charge.

S&F 4.80mm thick sheet glass ordinary quality and glazing with aluminium beading and rubber beading in square exc 0.50 sqm in each pane including hacking out the old glass pane complete all as specified and directed by Engr-in-charge.

S&F aluminium anodised barrel tower bolts of extruded section, 100 mm length, ISI marked.

S&F aluminium anodised barrel tower bolts of extruded section, 150 mm length, ISI marked.

S&F aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy, 300 mm long , ISI marked.

S&F 75 mm long stainless steel butt hinges heavy weight with stainless steel hinge pin, bright finished.

S&F 100 mm long stainless steel butt hinges heavy weight with stainless steel hinge pin, bright finished.

S&F extruded aluminium alloy handles, fabricated type, anodised 100 mm size, ISI marked.

S&F extruded aluminium alloy handles, fabricated type, anodised 150 mm size, ISI marked.

S&F in repairs 12mm thick, Medium density fibre board (MDF) exterior grade, fixed to timber frame work with screws in wall decoratives/panelling complete all as specified and directed.

S&F in repairs 12mm thick, Medium density fibre board (MDF) exterior grade, fixed to timber frame work with screws in kitchen/laboratry cabinets, tables, cupboards, partitions etc complete all as specified and directed by Engr-in-charge.

M&L for 0.90mm thick decorative laminates type 1 of surface finish, colour and pattern as approved by Engr-in-charge, fixed with approved adhesive as per manufacturers instructions complete all as specified by Engr-in-charge.

S&F in repairs brass 4 levers locks, drawer, grade I, size 50mm complete all as specified and directed by Engr-in-charge.

S&F in repairs brass drawer handles, projection drop (50mm to 65mm) on screwed plate complete all as specified and directed by Engr-in-charge.

S&F in repairs Godrej drawer channel/regular close ball bearing drawer channel length 20 inch (Pair) 45 kg capacity, 100% extension for cabinets of kitchen/table/wardrobe etc complete all as specified and directed by Engr-in-charge.

S&F in repairs Godrej steel slip-on soft closing concealed hinges for cabinate doors, smooth operating Hinges for full overlay doors & windows etc complete all as specified and directed by Engr-in-charge.

S&F Continious (Piano) hinges of 30mm flaps, mild steel, bright finish or electrogalvanised, complete all as specified.

S&F 2nd class hard wood (Sal) beads straight (any size) for glazed/ guazed joinery renewed including mitres etc, complete all as directed

S&F in repairs 2nd class hard wood (Sal) in scantlings in timber framed work and fixed, wrought, as in partition wall, cabinets, drawer, tables etc. complete all as specified and directed

S&F 12mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; and fixed with screws to timber frame work complete all as specified and directed by Engr-in-charge.

Supplying, fitting and fixing 12mm thick Laminated wooden Flooring Work conforming to EN13329:2006 with plank size not Iess than 1200 mm X 190 mm (with unilin/tongue-groove locking arrangement) having 0.2mm thick top abrasive layer over a decorative layer followed by a High-density fibreboard (HDF) having density > 850 kg/m3 substrate core over a rasin saturated backing layer and installing through unilin or tongue- groove system (having locking strength not less than 1000 kg/m) over a 2 mm thk underlayer polyurethene foam on polythene sheet 250 micron, over a smooth, flat, hard subfloor free from moisture (< 8%), grease etc. complete in all respect with requisite accessories like end profile, transition profile, reducer 'T' profile etc. wherever required and preparation of base including all other incidental works as per direction & satisfaction of Engineer in charge. Cost of Laminate Floor Accessories only (Skirting ,End edge, T- moulding,Reducer) shall have to be added separately,wherever required complete all specified and directed by Engr-in-Charge.

M&L wooden tiles matt finished of designed layer as apporved by Engr-in-charge with solid core of HDF of size (1200x200x8 to 10mm) laid over PVC foam 5 mm thick with SR adhesive over 50 mm micron polythene sheet in skirting complete all as directed by Engr-in-Charge including cornices fixed all around the floor having rounded angles, rounded nosings, tongued and grooved edge complete all as specified and directed by Engr-in-charge. Note : The colour of tile shall be as approved by Engr-in-charge.

S&F in repairs 20mm dia aluminium alloy Harrison/curtain rails powder coated with fixing brackets, stops, rollers (as approved) complete all as specified and directed

S&F aluminium (Die cast) body door closer hydraulically regulated,designation No 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg

M&L for providing post construction antitermite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart, including drilling and plugging 12mm dia holes with white cement mixed with coloured pigment to match the existing floor complete all as specified.

M&L for providing post construction anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same to match the exisiting surface complete all as specified and directed.

M&L for preparation of new or previously untreated wood and wood based surface of any description, over 10cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm complete all as specified and directed.

S&F in repairs wire mattresses and shaped nets of 4mm dia galvanised steel wire, 150 x 100mm mesh, made up into mattress or cages, lapped, or in gaping to avoids birds etc wired and laid in position including closing after filling complete all as specified and directed by Engr-in-charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar, including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stone work & precast concrete articles including copings etc.and removing debris outside MD land complete all as specified. Note: The place of disposal shall be find out by the contractor.

M&L for bickwork with subclass 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM (1:4) and finished even & smooth without using extra cement completed all as specified.

M&L for preparing new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified.

M&L for 2.00mm thick linoleum flooring and sealed with an approved adhesive including stretching, cutting and fitting complete all as specified by Engr-in-charge. Note ; The colour of flooring shall be as approved by Engr-in-charge.

Supply and fix in repairs 150mm brass handles, cast type, polished bright complete all as specified.

Supply and fix in repairs (100mm flange)Parliament hinges, cast brass type, bright polished and fixed complete all as specified.

M&L for 20mm thick second class hardwood (Sal) fascia boarding planed one side and edges tongued and grooved or rebated supplied and fixed with nails in any situation, including making design to match with existing fascia boarding complete all as specified and directed by Engr-in-charge. Note : The boarding shall be fixed upto a height of 30m from ground and quoted rates shall deemed to be included necessary scaffolding and all safety arrangements .

S&F moulding sectional area n. exc 6 sq.cm as in cornices,picture rails and the like complete all as specfied and directed by Engr-in-charge.

M&L for cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for insertinng holdfasts and making good dismantled portions in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required exc half brick but not exc one brick complete all as specified and directed by Engr-in-charge.

S&F wall panelling using second class hardwood ( Sal) boarding 15mm thick planed one side and edges tongued and grooved, width of panels exc 10cm and n. exc 20cm and fixed with coloured screws, nails, beads, jambs etc to timber frame work complete all as specified and directed by Engr-in-charge.

M&L for preparation of new or previously untreated wooden surfaces of any description over 10cm in width or girth and finish the wood surface with finishing coat of synthetic varnishing, over one under coat varnish,over filler coat with wood filler liquid transparent and make the surface fully shined complete all as specified and directed.

S&F 52mm thick PVC Partition consisting of 12mm thick plain solid PVC ply sheet reinforced with frame work made from 40mm x 20mm MS tubes. In between two MS tubes, 5mm thick plain heat moulded 'C' channel of size 75mm x 50mm with feathered edges shall be fixed on the floor, wall and ceiling. Plastic ply opanel shall be inserted in the PVC 'C' channel. The first & last MS Tube should be erected such that it is inside a PVC 'C' channel, in between adjoining plastic panel, 5mm thick x 75mm width plain PVC sheet feathered at edges shall be stick on the front & back face using solvent cement complete all as specified and directed by Engr-in-charge. Note: Colour and pattern of PVC ply will approved by Engr-in-charge.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. Note: - (i) Glass panes will be measured & paid separately. (ii) The rate quoted shall be inclusive of neoprene beading, glazing clips, screws, etc. as required but shall not be measured for arriving of weight. (iii) The rate shall be inclusive of the locking arrangement including complete packing with silicon gel around contacting surface of aluminium work with matching existing area. (iv) The size of aluminium sections shall be as per HQ CE(N) MZ TD drawing No TD/2021/01 to 05 and sill to be provided as per HQ CE(N) MZ TD of sill type 'A' and 'B' respectively if directed.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. Note: - (i) Glass panes will be measured & paid separately. (ii) The rate quoted shall be inclusive of neoprene beading, glazing clips, screws, etc. as required but shall not be measured for arriving of weight. (iii) The rate shall be inclusive of the locking arrangement including complete packing with silicon gel around contacting surface of aluminium work with matching existing area. (iv) The size of aluminium sections shall be as per HQ CE(N) MZ TD drawing No TD/2021/01 to 05 and sill to be provided as per HQ CE(N) MZ TD of sill type 'A' and 'B' respectively if directed.

Supply and fix concealed body lock for sliding windows 75mm long for sliding window shutter made of aluminium,anodised body complete all as specified and directed by Engr-in-charge.

S&F bearing/roller with metal body having plastic roller including screwed to shutter of aluminium windows complete all as specified and directed.

S&F Butt hinges 100mm size, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type B-21, ISI marked.

S&F floor door stopper of length with cover plate 140mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed.

S&F in repairs hydraulic door closer regulated designation no 3 universel type almn cast body suitable for door shutters of 851 to 1000mm in width and of wt between 61 to 80 kg cast iron body complete as directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar including removal of rubbish out side MD land. Note: The place of disposal shall be find out by the contractor.

M&L 20mm thick Granite (of any tpe) work (table rubbed and polished) in door/window steps, jambs, pillars, cills,cooking platforms and like including pointing in white cement using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed in CM (1:4) Complete all as directed by Engr-in-charge.

S & F sheet glasses, opaque / frosted on one side 4.80mm thick glazing all with aluminum beading, glazing pin etc, or with oil putty in square n exc .5 sqm in each pane all as specified and directed

S&F in repairs Aluminium alloy wire cloth , 0.45 mm nominal dia of wire and average width of aperture 1.40mm complete fixed with aluminium wire staples and beads etc all as specified & directed .

S&F in repair aluminium anodised DECO grill(anodised transparent or dyed to required shade according to IS 1868 with minimum anodic coating of grade AC 15) DG-104 fixed with necessery U/F/H channel, of approved disign/pattern, with approved standard section and fixed to existing window frame with CP brass/ stainless steel screws@ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engr-in-charge.

S & F in repairs 12mm thick toughened glass door , double/single shutter, including SS pivot of floor door closer, SS corner support, SS handle 600mm long fixed at both sides of both shutter and also including necessary SS accessories, like clamps etc. complete all as specified and directed by Engr-in-charge.

Supply and fix 10mm thick toughned glass as in hinged doors, partitions, automatic doors and similar works including cutting to shape, drilling holes required complete all as specified and directed by Engr-in-charge.

M & L for hacking out old broken glass form metal frame including punching or drilling out old glazing pins/ spring clips and providing and fixing new ones with all necessary fixing accessories complete . Note:- glass should be measured and paid seperately.

S&F solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land. Note: The place of disposal shall be find out by the contractor.

S&F in repairs plain aluminium sheet false ceiling system consisting of 600mm x 600mm pre coated aluminium tiles of 0.70mm thickness of white colour laid over and including GI powder coated grid system consisting of 15mm wide T- section flanges in white colour having rotary stitching o the main runner, 1200mm & 600mm cross tee with a web height of 32mm, perimeter wall angles of size 19mm x 19mm secured to walls at 450mm c/c with cadmimum plated screws including necessary fitting and 4mm GI suspenders fixed to slab using anchor fastener in ceiling of length as required on site complete as per manufacturer instructions including taking down carefully existing false ceiling with electrical fittings/fire sencers after disconnecting. Note:- The rate includes for necessary cutting in false ceiling for fixing electrical fittings, fire sencers etc and making electrical connections as per existing complete.

S&F in repairs ceiling fitted pulley operated clothes drying system consisting of anodized aluminium pipes, each of outer dia 22mm and inner dia 19.8mm of size 9 feet .Pulley made up of Delrin with rope guide mounted on channel pair of length 24" Each with locking system to hide rope knot, channel to be mounted or fixed with self tapping screws(38mm x 8) provided in kit and rope will be polyester braided undyed of 4mm dia.

S&F Factory made single extruded WPC (wood polymer composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non toxic additives (Maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), miniumum compressive strength 50 N/mm2, modules of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessay full body threaded star headed counter sunk S.S screws, all as per direction of Engr-in-chare.

S&F Factory made single extruded WPC (wood polymer composite) solid door frame/chowkhat of size 50 x 100mm comprising of virgin polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non toxic additives (Maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum density of 750 kg/cum and screw withdrawal strength of 2200 N (face) & 1100 N (Edge), miniumum compressive strength 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required and length complete as per direction of Engr-in-charge. Note- MS hold fast/lugs or SS dash fasterners shall be measured and paid for seperately.

Supply & Fixing solid PVC door frame of size 50mmx 47mm made out of 5mm wood grains printed PVC sheet reinforced with MS square tube and edges painted to match with printed sheet complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing factory made solid panel PVC door shutter 30 mm thick (styled) consisting of frame made out of MS tube for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ,C" channel having a PVC sheet strip of 20mm width stuck in side with salvent cemet for stiles and plain colour PVC sheet for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet bedding and jointed together with solvent cement suppling and fixing in the frame at site complete all as specified and directed by Engineer-in-Charge.

jkconstruction (BID ID -3501871)

SN CONSTRUCTION (BID ID -3499812)

GANGAJAL (BID ID -3502056)