CARRYING OUT REPAIR AND RENOVATION WORKS AT BEL-HYD BTA AT KAVADIGUDA.

PART A CIVIL WORKS

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km or all lifts, complete as per directions of Engineer-in-charge.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, sunshades etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level/or above plinth level and Thermomechanically treated bars of grade Fe500D or more. Base Rate: Rs. 65 per Kg.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 5.0 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 5.0 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, Area of slab over 0.50 sqm (Basic price : Rs.2500 per Sqm)

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineerin- charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/ sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming : to IS 2095: (part 1) : 1996 (Board with BIS certification marks)

Providing and fixing factory made uPVC white colour windows/ ventilators comprising fixed glazing and adjustable glass louvers made out of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Gutter (600 mm over all girth)

Providing 12 mm thick cement plaster of mix : 1:4 (1 cement: 4 fine sand) on walls including necessary scfollding etc upto 5 floors ., complete

15 mm cement plaster 1:2 (1 cement : 2 stone dust) on the rough side of single or half brick wall.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches using crack sealer wherever required etc. complete

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade One or more coats on old work

Polishing in high gloss/matt finish melamine polish on old wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. Remove the existing polish thoroughly with suitable sand paper/ tools, then the surface to be polished is rubbed with sand paper 80/ 120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Dismantling W.C. Pan/urinal/washbasin of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area beyond 3 sq. metres

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I.cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm precast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)

Supplying and applying single component, elastomeric 100% pure polyurethane coating, which is free from bitumen & tar and meets the requirement as per ASTM C 836-18, having elongation of 400% (As per ASTM D412), Tensile strength greater than 2MPa (As per ASTM D 412), Tear strength greater than 15 N/mm (As per ASTM D 624), Water Vapor Permeability greater than 25 gm/m2/day (As per ISO 9932:91), Adhesion to concrete more than 1.5 N/mm2 (As per ASTM D4541), Resistant to plant roots as per UNE CN/TS 14416, applied with a total consumption of 2.3 Kg/Sqm to achieve a minimum of 1.5 mm system DFT to satisfy the requirements of LAM as per ASTM C898, including reinforcing the coating with 45gsm glass fibre mesh at all corners and change in directions. The coating shall be continued to the entire horizontal area and should be terminated at 300mm above FFL over the vertical surface as per manufacturers specification and methodology. The system includes base preparation of cleaning, brushing and removal of flacky materials, grouting the porous area with cementitious grout, proper coving between slab and wall junctions and priming the surface with high moisture insensitive epoxy primer applied with a total consumption of 200 gms/Sqm, followed by application of polyurethane coating in two coats. Approved Makes: Dr. Fixit, BASF, SIKA Mode of Measurement : Actual area Treated as per direction of Engineer-In-Charge. (Note: The work shall be got done through a professional agency).The water proofing work shall carry a guarantee to the effect that the structure will remain water and leak proof for 5 years from the date of handing over the building after completing the water proofing treatment.)

Wall painting on old surface with premium acrylic emulsion paint (Asian apcolite premium emulsion or equivalent ) of interior grade , having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture,including removing the existing paint, sealing the cracks with crack sealer, applying one or two coats of wall putty of approved brands, preparing the surface with suitable sand paper/buffing tools, including one coat of primer, applying additional coats wherever required to achieve even shade and colour. (including necessary scaffoliding scaffolding system (cup lock type) with working platform for work men having all essential safety features upto 5 floors)

Providing and laying of specified size and minimum 8 mm thick antiskid matt vitrified in toilet flooring with water absorpition less than 0.08% and conferming to IS:15622 of approved make colours and shades laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand ) tiles shall be laid with out of spacers and filled with matching tile matt grout and finished with epoxy grout etc . complete (Basic price : Rs.750 per Sqm)

Providing and fixing Ist quality Vitrified wall tiles ( Kajaria make or equivalent) conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with tile grout@ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Basic price : Rs.600 per Sqm)

Repairing and relaying of the existing paver-block floor by taking out CC interlocking paver blocks from the footpath/Drive way, including removal of rubbish, disposal of unserviceable material to the dumping ground, Supllying coarse sand and providing 150 to 100 mm thick compacted bed of the coarse sand, relaying the removed CC Pavers to line and level and filling the joints with sand, compacting eith vibro compactor etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing 50mm PVC SWR grade pipes and specials of make FINOLEX, SUPREME, PRINCE for waste and vent pipes etc complete including necessary accessories, bends. Tees, adhesives, clamps etc as per manufacturers specification.

Providing and fixing 75mm PVC SWR grade pipes and specials of make FINOLEX, SUPREME, PRINCE for waste and vent pipes etc complete including necessary accessories, bends. Tees, adhesives, clamps etc as per manufacturers specification.

Providing and fixing 110mm PVC SWR grade pipes and specials of make FINOLEX, SUPREME, PRINCE for waste and vent pipes etc complete including necessary accessories, bends. Tees, adhesives, clamps etc as per manufacturers specification.

Providing and fixing 100 mm inlet and 75 mm outlet PVC trap of FINOLEX / SUPREME with stainless steel grating (with or without hole for PVC waste pipe of CHILLY/NOWAY make) including the cost of cutting and making good the walls and floors.etc., complete.

Providing and fixing of 110mm PVC pipe for taking rain water down using GI slotted channel and bolts including necessary PVC bends, shoes, making bore holes in slab / wall and bore packing of the same, all complete as per directions of engineer in charge.

Providing and fixing wall mounted EWC with matching colour PVC seat cover Cat. No.: 92055 (P-23) of hindware make of size 71 x 37 x 79 cm, with inbuilt Cistern of cat no: 92121 with 'P' or 'S' trap and 15mm CP health faucet of jaquar (Cat.no. 573) etc. including cutting and making good the wall, floors wherever required and making connecting to the water supply and sanitary pipe lines with required fixtures. complete as per direction of EIC.

Providing and fixing Table top wash basin of size 480 x 365 x 135 mm ( Make:Hindware, Model: Cat No 91041 - Pastel) with Waste Coupling of size 32mm Full Thread with 130mm height of (Make : Jaquar, Model:ALD-705L130 ) and bottle trap of 32mm size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange standard pattern (Make:Jaquar, Model:ALD-WHM-769L300x190) (with Internal Partition) and Pillar cock with Base Flange of jaquar make, model: FLR-CHR-5021M conforming to IS:8931 : 15 mm nominal bore including painting of fittings and brackets, cutting and making good the walls wherever require.

Providing and fixing of HSH-1721 Hand Shower ø105mm Round Shape Multi Flow with Air Effect (ABS Body & Face Plate Chrome Plated) with Rubit Cleaning System with holder and SHA-549D12 with 12mm dia & 1.5M Long with Nuts complete as directed by engineer in charge

Providing and fixing bib cock with wall flange KUP CHR 35037 PM of jaquar make conforming to IS:8931 : 15 mm nominal bore

Providing and fixing AKP-GRF-35731P (GRAPHITE) Soap Dish Holder as dircected by Engineer - in - charge.

Providing and fixing Bib Cock Kubix Prime-SPJ CHR 35463PM of jaquar make conforming to IS:8931 : 15 mm nominal bore

Providing and fixing shower arm (SHA-CHR-479L450) of 450mm length with shower head of 150mm sqare (OHS CHR 35495) of jaquar make conforming to IS:8931 : 15 mm nominal bore

Providing and fixing 2-way Bib Cock with Wall Flange ARI-CHR-39041 of jaquar make and Hand Shower (Health Faucet) with 1 Meter Long Easy Flex Tube in Chrome Finish and Wall Hook with N.R.V (Back Flow Preventer) 15 mm nominal bore ALD-CHR-573 with necessary fittings complete as directed by engineer in charge.

Providing and fixing KUP-CHR 35053PM Angular Stop Cock with Wall Flange of jaquar make conforming to IS:8931 : 15 mm nominal bore

Providing and fixing Single lever Exposed Parts Kit (ALI CHR 85065MK) with Concealed body for single lever high flow Diverter (ALD-CHR-079N) of jaquar make conforming to IS:8931 : 15 mm nominal bore

Providing and fixing of SS grating over traps of size 100mm of round or square shape as directed by engineer in charge

Providing and fixing Towel rod of length 450mm long of Jaguar make cat no. ACN-1111BNM with matching CP screws etc complete

Providing and fixing composite doors of required size of Fimen/ Suraksha/Durian conforming to IS: 4020 (latest) to the following specification. The single leaf shutter shall be of rigid GRP sandwiched composite structure of 30mm thick (min) laminated on all sides with GRP skin fabricated using UV stabilised isophthalic Gel coat and one layer of 450 gsm E-Glass chopped strand Mat (CSM), Impregnated with polyester resin. The thickness of the skins shall be not less than 1.5mm thick. Expanded polystyrene (EPS) structural foam panel of density 20kg/cum shall be used as core material for the whole area of door except the wooden frame structure. The wooden reinforcements shall be made of seasoned sal wood block of minimum cross section 70 x 26mm for lock side, 40 x 26mm alround forming the frame the work for shutter and a minimum of 75mm wide intermediate strip for the width of the door for fixing locks and fixtures. The finish of shutter shall be grains and of approved colour. The door frame shall be of 90 x 60mm (min) and of same colour of shutter made with GRP sheets of 1.5mm min. thickness and reinforced with 3 Nos. of 200mm long, salwood pieces of suitable size on each vertical side of frame for fixing of hinges and locks and the balance portion of the frame shall be filled with light weight concrete including providing and fixing 6 Nos. of 260 x 25 x 5 mm size MS hold fasts, 3 Nos of 100mm long SS heavy duty hinges with counter sunk screws, 1 No. of 200mm long powder coated aluminium aldrop bolts, 2 Nos. of 125mm long powder coated aluminium plain door handles, 2 Nos. of 100mm long powder coated aluminium tower bolt for each shutter etc all complete.

Providing and fixing factory made uPVC white colour casement / casement with fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Casement cum fixed panel window having both end single casement panel with fly proof S.S wire mesh, middle fixed panels

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension.

Providing and fixing Birla 3M sticker etching of approved color shade to form logo, design patterns etc on the existing glazed windows as directed by Engineer In Charge. Rate quoted shall be for the complete finished work including all the materials and labour. Actual area of etching provided will be measured for payment.

Providing and Fixing of Godrej Cylindrical locks keyed (entrance) stainless steel, product code-5329 & UNSPSC code-46171596SD00016 with necessary fittings complete as directed by engineer in charge.

Providing and fixing Aluminum composite panel (ACP) in aluminum doors shutters and partition frames, 2 Panels per frame to be provided to give uniform look for both front and rear face of the door/partition including necessary screws, EPDM /neoprene gaskets, and fittings etc., complete as per the directions of engineer-in-charge. (Elevation area of the ACP will be measured for payment, Aluminium frame works shall be paid seprately )

Painting Existing Aluminium Composite Panel wall Cladding work with Two or more coat MRF metalic spray polish to give an even shade. Panels should be cleaned before painting with sand grit paper of grit size 80 to 100 then after grit 400. including necessary scaffolding and platforms for upto V Floors

Supply and installation of Mulicell Standing Seam Polycorbonate panels having flux 7.0 as per EN 16153 & EN ISO 10077-2. For min joints, panels shall be 1000-1200 mm wide with standing seam on both sides. Panels shall have minimum six-seven layers with truss bridge design for higher flexibility and strength. The system shall be secured using suitable connectors with double tooth grip lock locking mechanism and fixed purlin having a pull out load of min 7000N tested as per ISO 6892-1998 and IS 1608-2005. Make: DPI Daylighting/Equivalent

Removal of existing backer rods, weather silicone sealant and replacing with new backer rods and weather silicone sealant of Dow corning or equivalent make, all required to refix aluminum composit panel in the same position inluding necessary scaffolding to work at a height upto V floors

Providing and fixing approved quality, colour and make Exterior grade Roller blinds for outdoor areas with necessary fixing arrangements etc complete.

Providing and fixing 150mm dia PVC soil waste and vent pipe ( including specials) conforming to IS:13592 of SWR quality of 6kg /cm2 pressure including all fittings, like EG : Bends, Tees, Elbows, Collars, junction, inspection doors, cowls, offsets, access pipes, jointing with rubber ring / solvent cement by application of leak proof adhesive like FRP paste including cutting holes in walls and floors and making good.

Dismantling tile work in Walls laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Removing stop cock/pillar tap/ wall mixer/ spout/all other plumbing fittings of all sizes including stacking of same in premises all complete as per directions of Engineer-in- Charge.

Providing external Wall Plaster Repair (Removing & Repair of external loose plaster):- Chipping of loose mortar using light chisel & hammer also preparing surface to receive further treatment, disposing the debris as directed by Engineer-in-charge at designated place inside the campus. Restore the cover concrete of R.C.C. structural members in two layers, by applying 20mm thick polymer mortar which is CM of 1:3 admixed with Dr.Fixit Pidicrete URP ( or Equivalent products from Sika / Fosroc) at a dosage of 12-15% ( or as per manufacturer specification) of Cement and a bond coat of Dr. Fixit Pidicrete URP ( or Equivalent products from Sika / Fosroc) mixed with Cement at a ratio of 1:1. Cure these surfaces for 7 days. Note: Treatments should be done with authorised skilled person only. Rate is including necessary cup-lock scfollding and working platforms to work at hight upto V floors.

Providing treatment for seperation crack at the junction of RC Member & Masonry wall (Seperation cracks treatment):- Existing plaster along the crack shall be removed on either side of the crack for a width of about 250 mm (on either side of the wall), cleaning the same thoroughly with running water, applying a Polymer Bond Coat of Dr. Fixit Pidicrete URP ( or Equivalent products from Sika / Fosroc) and Cement at 1:1 ratio. on the cleaned surface. Use chicken mesh and fixed across the crack using ‘U’ nails followed by gaps should be filled up with Dr. Fixit Repair Polymer Mortar ( or Equivalent products from Sika / Fosroc) , maintain the moisture on plastered surface for 7 days as per standard methodology. Note: Treatments should be done with authorised skilled person only, Rate is including necessary cup-lock scfollding and working platforms to work at hight upto V floors.

Part-B Electrical Works

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet.

Supplying and fixing following modular switch/ socket on the existing modular plate& switch box including connections but excluding modular plate etc. as required. 2 way 5/6 amps switch

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess including associated civil works etc., as required. 12 module (200mm x 150mm).

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 8 module (125mm x 125mm).

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 6 module (200mm x 75mm).

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 3 module (100mm x 75mm).

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 4 module (125mm x 75mm).

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 185 sq. mm (57mm).

Providing and fixing following capacity TP&N disconnector fuse switch unit with enclosure box with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required. 200 A TP&N.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Providing and fixing following rating and breaking capacity MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 150 A, 16 KA TPMCCB.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole and neutral.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Providing and fixing of 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 2.5 sq.mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 4 sq.mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2 x 1.5 sq.mm

Supplying and fixing of following sizes of medium class 25 mm PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (Ref Make: Universal/Supreme/Classic).

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group-B

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc as required. Group-A.

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required 120 sq. mm

Supplying of all the required materials of approved make to construct a maintenance free chemical earthing system as per drawing & detailed specification. Each set of earthing pit shall consists of a copper bonded solid steel rod electrode of 17.2mm dia x 3.0 mtr length with required quantity of nontoxic electrically conductive concrete/backfill compound, Copper/brass termination busbar & bolt-nuts, washers etc. The work includes drilling/making a hole of 250 mm dia in the ground to required depth by manual or mechanized method, keeping the electrode in the centre of the pit, filling the already prepared semi solid paste/slurry of backfill concrete/compound fully & curing, all the civil works such as excavation, refilling, construction of brick chamber, RCC cover, curring etc. The complete work shall be carried out as per our drawing and manufacturers instructions/ mannuals or as per standard. Note: The earth enhancing compound/concrete shall be of low resistivity conforming to IEC 62561-7 standard. (Makes: Erico/ Loress/ Indelec/ JMV/ LPI/ Ashlok.

Supplying and fixing of 18W surface mount downlighter, LED Fitting and fixing of the same with clamps screws/anchor bolts-nuts, washers etc., as required directed by engr-in charge. Ref:- similar to wipro LD80-171-XXX-60-SM. or equivalent in approved makes.

Supplying and fixing of 6WATT TRIMLESS COB recess mount downlighter, Lumen: 530, dimentions: (50X53) mm, beam angle: 63 degree and fixing of the same with clamps screws/anchor bolts-nuts, washers etc., as required directed by engr-in charge. Ref:-Wipro 06W6500K. or equivalent in approved makes.

Supplying and fixing of 15 WATT SLEEK RD LED Sleek round recessed mounting LED downlight with AL die-cast body, finish with drop down PC diffuser to deliver low glare illumination with optimized heat sink for efficient heat dissipation. Ref model: BGSLO SLEEK 15W WH RD or equivalent from approved make.

Supplying of fully automatic hand drier suitable for 230V, 50Hz AC supply, twin blower integreted with timer cum infrared sensing system and fixing of the same on wall by providing suitable TW guttas, screws, bolt-nuts etc., as directed. (Ref make: DOLPHY DAHD0011, 1800W or equivalent approved makes.)

Supplying, fixing and testing of 2''x2'' Square 36 W/40W recess mount, LED Fitting and fixing of the same with clamps screws/anchor bolts-nuts, washers etc., as required directed by engr-in charge. (Ref: Similar to Wipro-Elate LED CRCO10 surface/recesse type). or equivalant from approved makes or directed by engineer-in-charge.

Supplying of LED luminaire as per below mentioned specification of make/brand as per approved list in DTS and fixing of the same in the ceiling by providing required clamps, TW guttas, bolt-nuts/screws, washers, making electrical connections, earthing etc., as required/ directed by engineer-in-charge Mounting type :- Surface mounting type Type :- 2ft LED tube luminaire (MIRROR LIGHT) System rated power :- 10W Ref model :- BAJAJ:- BCLSB 10 NW or equivalent approved makes.

Supplying of outdoor type LED post top Lantern luminaire with opal acrylic cover suitable for 35 Watt LED lamp IP-65 rating along with complete acessories such as control gear/driver etc. and fixing of the same above the already provided post top lantern poles, making electrical connections earthing etc as directed by engineer-in-charge. (Ref Make: Wipro- LP-07-431-XXX-57-CL) or equivalent approved makes.

Supplying, installation & testing of 5 star rated electric water gyser Wattage:2000W, Capacity:25Ltrs, Star rating:5, energy efficient storage water heater with fast heating, 3 level safety: capilary thermostat, automatic thermal cut-out & multi-functional valve to provide higher safety. Inner tank material: SS304, outer body material: CRCA. Ref make: Crompton, Racold or equivalent approved makes.

Supplying, fixing and testing of Water pressure Pump/Booster pump of capacity 1.1KW (ref: PASCPM170C) suitable for toilets, faucets, showers,bath, dishwasher & washing machine etc. alongwith all required consumables accessories or directed by engineer-in-charge.

Releasing of all type of switch boards, LED fitting, Ceiling fans & wall mounting fans from the existing position along with aceesories/cables after disconnection of power connections and returning of the same to stores as directed by engineer-in-charge.

Dismantaling & removal/releasing of all type of MCB disitribution boards along with MCBs/RCCBs/MCCBs after disconnection of power connections and returning of the same to stores as directed by engineer-in-charge.

Supplying & erecting of 200 mm sweep, single phase plastic body exhaust fan with mesh cover/automatted shutters & all acessories and installation of the same by providing suitable nut/bolts/screws and making good electrical connection, earthing, testing etc. as required. The electrical connection shall be made by providing suitable size PVC insulated flexible copper cable from already provided ceiling rose as required. Ref model :- Bajaj(MAXIMADxI 200) or equivalent in approved makes.

Supplying & erecting of 450 mm sweep, single phase metalic body exhaust fan with all acessories and installation of the same by providing suitable nut/bolts/screws and making good electrical connection, earthing, testing etc. as required. The electrical connection shall be made by providing suitable size PVC insulated flexible copper cable from already provided ceiling rose as required. Ref make:- Bajaj/Usha/Crompton/Havells or equivalent in approved makes.

Supplying & erecting of 250 mm sweep, single phase plastic body exhaust fan with mesh cover/automatted shutters & all acessories and installation of the same by providing suitable nut/bolts/screws and making good electrical connection, earthing, testing etc. as required. The electrical connection shall be made by providing suitable size PVC insulated flexible copper cable from already provided ceiling rose as required. Ref model:- Bajaj(MAXIMADxI 250) or equivalent in approved makes.