GE/PNH-02/2021-22

Amount

B&R PORTION:- Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

Dismantling of timber scantling under 40sqcm in section unframed work as in fillets, rails, posts, rafters, purlins etc, complete all as specified and directed.

S&F Suspended false ceiling using E- grid suspended ceiling grid system of grid size 600x600mm with GI frame work of main runner 38 x 24mm sheet thickness 0.4mm, cross Tee 28 x 24mm sheet thickness 0.3mm and wall angle 24 x 24mm x 0.5mm using 4mm thick high pressure stream cured classic variant E-board, designer pattern (ISI marked, IS No 14862-2000) & E board to be placed in the grid suspended by 4mm GI wire hangers from the purlins of the roof with butter fly clips, complete all as specified and directed. Make:- Everest Industries Ltd of equivalent as approved by GE.

M&L for 50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, including filled the joints with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base floor finishing surface even and fair, complete all as specified and directed.

M&L for Cement concrete (1:2:4) type-B-1 (using 20mm graded stone crushed aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, bed block, kneelers, apex stones, bed plates, roof kerbs round or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for Chequered cement concrete tiles 300x300x 25mm thick, set & jointed in neat cement slurry in floors and pointed with grey cement mixed with pigments, laid over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11Sqm but n exc. 0.18Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exc 0.11Sqm but n exc. 0.18Sqm in vertical surfaces such as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles,fixed over and including 10mm thick plaster in CM (1:4), complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for Glazed ceramic coloured tiles (300x200mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

M&L for Machine cut Kota stone slab flooring 20-25mm thick , bedded and jointed with grey cement slurry and pointed with grey cement with admixture or pigment to match the shade of Kota stone slab as approved by GE, laid over and including screed bed or bedding layer of mortar 20mm thick in Cement Mortar (1:6) including cutting, grinding and mirror polishing, complete all as specified and directed.

M&L for Machine cut pre polished Kota stone 20-25mm thick as in riser of steps, skirting, dado and pillar fixed over & including cement plaster 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the kota stone including cutting, grinding and mirror polishing, complete all as specified and directed.

M&L for Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

M&L for Walling of random rubble stone masonry uncoursed , well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

All as per ser Item No 19 above but except stone, complete all specified and directed.

Extra over stone walling of random rubble walling, uncoursed or brought for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified and directed.

M&L for Rendering 20mm thick on other than fair faces of brick or stone masonry wall surfaces in cement mortar 1:4 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick cement plaster rendering in CM 1:4 on fair faces of bricks or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on other than fair faces of brick or stone masonry wall surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for Preparation of newly plastered or unplastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

M&L for Preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of oil emulsion distemper over and including 1-3mm thick wall care putty, complete all as specified and directed.

M&L for Applying three coats of white wash including preparation of newly plastered surfaces of wall complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Dismantling of timber scantling 40sqcm and over in section, as in any position, complete all as specified and directed.

S&F 0.63mm thick galvanised corrugated mild steel sheeting with grade of Zinc coating of 275 gms/Sqm with two corrugation side lap and at least 150 mm end lap , fixed with L or J type or cranked hook bolts, in roof, walls etc, complete all as specified and directed.

All as per item No. 31 above, but except sheeting, complete all as specified and directed.

S&F 0.80mm thick plain galvanised mild steel sheeting with 275 gm/sqm Zinc coating as in ridge , hips, valley gutters, drip and straight flashingfixed with L or J type or cranked hook bolts, in roof etc., complete all as specified and directed.

S&F Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connected plate confirming to Fe 410W(Gde E-250), quality 'A' complete all as specified and directed.

S&F Mild steel work as in wind ties for roof including securing bolts, including all necessary drilling, bolting or riveting etc. and similar work conforming to Fe-250 Gde E-165 complete all as specified and directed.

S&F 2nd class soft wood (Kail) as in scantling, clean sawn fixed, complete all as specified and directed.

Taking down shutters of any description exceeding 1sqm and not exceeding 2sqm each, complete all as specified and directed.

Taking down shutters of any description not exceeding 1sqm each, complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5Sqm each, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each, complete all as specified and directed.

S&F 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc divided into square (with sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F 30mm thick 2nd classhard wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc divided into square (with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (b) supplied and fitted to chowkats complete all as specified and directed.

S&F Factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam (Nut brown colour) PVC Sheet on the front face & 2mm prelam (Nut brown colour) PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed. Note:- Cadmium screws to be used for fixing and fixtures of fittings.

S&F Mild steel butt hinges, medium weight, cold rolled,100mm long fixed, complete all as specified and directed.

S&F Mild steel butt hinges, medium weight, cold rolled,75mm long fixed, complete all as specified and directed.

S&F Aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

S&F Aluminium anodised, barrel tower bolts of extruded section of size 100mm and fixed, complete all as specified and directed.

S&F Aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S&F Aluminium alloy handles, cast type, anodised of size 100mm and fixed, complete all as specified and directed.

S&F 250mm long aluminium alloy anodized sliding door with haps, staple (bolt type) and fixing clips of sheets, cast or extrusted sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beading complete all as specified and directed.

S&F 300mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for Preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of Ist quality over a coat of pink primer, complete all as specified and directed.

Taking up or down steel tubing of 15/20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

S&F Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repair Bib tap 15 mm bore with flange, Brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed. Make:- Jaquar cat part No CON-047KN or equivalent cat part of make as specified in P.S.

S&F in repair Angular stop valves cast copper alloy 15 mm dia, fancy type, chromium plated with wall flange screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions complete all as specified and directed. Make-Jaquar Cat Part No:-CON-059KN or Equaivalent cat part of make as specified in P.S.

S&F in repair Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed. Make:- Prayag cat part No-4054 or Equaivalent cat part of make as specified in P.S.

S&F in repair PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints, complete all as specified and directed. Make:- Prayag cat part No 501 or Equaivalent cat part of make as specified in P.S.

S&F in repair Vitreous china wash hand basin, white, flat back, size 550x400 mm excluding taps, waste, chain & plug and porcelain stopper but including brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed. Make-Prayag Cat Part No:-4645 or Equaivalent cat part of make as specified in P.S.

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 450mm complete all as specified and directed.

S&F in repair 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe complete all as specified and directed. Make:- Jaquar cat part No-CON-011KN or equivalent cat part of make as specified in P.S.

S&F 32mm dia PVC corrugated waste pipe with union 800mm long complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint to walls as soil pipe with & including clamps, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint to walls as soil pipe with & including clamps, complete all as specified and directed.

S&F in repair Vitreous china urinals, bowl type of size 465x355x265mm (minimum) white with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with automatic flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe complete all as specified and directed. Make:- Prayag cat part No-4999 or Equaivalent cat part of make as specified in P.S.

S&F in repair Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), suitable for floor taps, complete all as specified and directed.

Dismantling PVC water tanks and removing to storing of capacity not exceeding 500 ltr complete all as specified and directed.

Dismantling PVC water tanks and removing to storing of capacity exceeding 500 ltr and not exceeding 1000 ltr complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs incl with 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs incl with 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames or stone/ concrete, glazed with putty or fixed with beads, complete all as specified and directed.

S&F Sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and directed.

S&F Figured glass pin headed type, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beading, complete all as specified and directed.

M&L for Applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed.

S&F Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for Plain cement Concrete 1:3:6 type-B1 (using 20mm graded crushed stone aggregate) as in copings, hold fasts plinth band, bed blocks and like slightly rounded or chamfered angles as directed including necessary form work, complete all as specified and directed.

S&F in repair MS powder coated tubular curtain rod fancy type of 25mm dia complete all as specified and directed.

S&F MS powder coated decorative type bracket, end ball, rounded block, bracket (coated with brown/cherry/golden colour) suitable for 25mm dia curtain rod of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed.

M&L for 12mm thick both sides prelaminated particle board, medium density fixed with screw to frame work in cup board shutters, partitions, shelves etc complete all as specified and directed.

Cleaning / disinfecting of PVC / RCC water storage tank of any capacity with disinfecting chemicals (Chlorine) properly with water thoroughly flushed out, complete all as specified and directed.

M&L for Preparation of old plastered/ un-plastered wall surfaces including brooming down or steel wire brushing, scraping down, smoke soot, mould, moss, efflorescent salts, trading oil and greasy spots, and applying one coat of white wash on walls including cornices, pilasters etc, complete all as specified and directed.

Complete removal of existing treatement and applying two coats of white wash on wall, complete all as specified and directed.

All as per item No. 88 above, but on ceiling, complete all as specified and directed.

All as per item No-88 above but applying one coat of colour wash on walls, complete all as specified and directed.

All as per item No-88 above but applying one coat of distemper oil emulsion white or any tint, complete all as specified and directed.

Complete removal of existing treatement from wall plaster and applying two coats of oil bound distemper white or any tint, complete all as specified and directed.

All as per item No-88 above but applying one coat of cement base paint on wall and AC sheet roof surfaces, complete all as specified and directed.

Complete removal of existing treatement from wall plaster and applying two coats of cement base paint, complete all as specified and directed.

M&L for Preparation of old painted steel surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern/single shade, complete all as specified and directed.

M&L for Preparation of old painted wooden or wood based surfaces of any description not otherwise described, over 10cm width or girth including knotting and stopping as required and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for Applying wall care putty of approved make not less than 1-2mm thick on walls as per manufacturar instructions with and including rubbing by means of sand / abrasive paper to have smooth finishing to receive primer / paint, complete all as specified and directed.

Writing letters or figures (Block, Roman, Italic or Indian) n. exc 30cm high with synthetic enamel paint including oblitering old writing of any description to match existing work, complete all as specified and directed.

E&M PORTION:- Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

Taking down carefully unsv sub main wiring including earth continuity any type/ size with surface casing/ caping/ TW batten/ PVC conduit surface or recess etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and directed.

Taking down carefully unsv main switch / DBs alongwith MCBs any type / capacity and making good disturbed surface to match with the existing surface, complete all as specified and directed.

Point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light/fan point controlled by one way switch 6 Amp complete all as specified and directed.

One ligh point controlled by two way switch 6 Amp complete all as specified and directed.

One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed.

One 3/5 pin socket outlet 6 amp independent board complete all as specified and directed.

One bell point controlled by one way switch 6 Amp complete all as specified and directed.

All as per srl item No 103 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 1.5 Sqmm as in continuous earth wire complete all as specified and directed. Make of wiring wire against item No- 103 to 104: Havells/RR Kabel/Finolex

S&F in repair Ceiling rose, 3 phase PVC/poly carbonate, insulated body, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Switch piano flush type 6 Amp two way, (ISI marked), complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Switch piano bell push flush type 5 Amp single pole one way (ISI marked) complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Switch socket multipurpose combination 2 in 1, 3 pin, 5 Amp flush type universal, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Switch socket multipurpose combination 2 in 1, 5 pin, 6 Amp flush type universal, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Switch socket outlet multipurpose combination 2 in 1, 6 pin, 5 and 15 Amp flush type universal, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. for 1200 / 1400mm sweep, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Electric bell ding dong type 230 volts AC supply 50 Hz complete all as specified and directed by Engineer-in-Charge. Make:-Havells/Anchor/Legrand

S&F in repair Tube light fitting box type suitable for LED 20W tube rod made out of ultra bright, glass shell, glare free, wide angle, single side connection retofit LED tube with G13 lamp holders complete with hosing with all accessories pre wired and making connection with copper flexible cable of appropriate size from ceiling rose to light fitting including 20LED tube rod 4 feet long with single side connection complete all as specified and directed. Make:-Havells Cat Part No:-LHLDEFXD5L8R020 for LED tube rod & Cat Part No:-LHFXCEP1TNNW020 for batten fittings or Equivalent cat part of make:-Wipro / Crompton / Bajaj Note :- The LED batten and LED tube rod shall be of same make.

S&F in repair gate light fittings, outdoor type, high power LED 25 watt, prewired with suitable pole for mounting complete all as specified and directed. Make: Havells cat part No. CORALPT25WLED757PSYMTOPC or equivalent of Make specified in PS.

S&F in repair LED street light fittings 30W made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 complete with hosing with all accessories pre wired with and including 40mm dia GI pipe bracket of 1.2 mtr made to shape as required fixed on wall or pole with FI clamp of required shap & 40x6mm siize, nut, bolts, washers and making connection with three core copper flexible cable of suitable size to light fitting complete all as specified and directed. Make:-Havells Cat Part No:-ENDURAPEARLSL30WLED757SASYTOPCMP or Equivalent cat part of Make specified in PS

S&F in repair new generation, energy saving, environmental friendly, long life, asthetically designed, aluminium landscape luminaire 0.6 metre height outdoor type fixed on wall or floor with nut, bolts, washers or screw and making connection with three core copper flexible cable of suitable size to light fitting including necessary steel fabricated stand up to 400mm and PCC work complete all as specified and directed. Make: Havells cat part No. BAMBOOBLS8WLED830PSYMTOPC (0.6 M) or equivalent cat part of make specified in PS.

S&F in repair Tube light fitting suitable for LED 10W tube rod fittings including 10 Watt LED tube rod complete with hosing with all accessories pre wired and making connection with copper flexible cable of appropriate size from ceiling rose to light fitting complete all as specified and directed. Make:-Havells Cat Part No:LHEXBYPNIN1W010 or Equivalent cat part of make as specified in Appx 'A' to P.S. Note :- The LED batten and LED tube rod shall be of same make.

S&F in repair Ceiling mounted decorative light fixture made up of polycarbonate, suitable for 18W LED lamp with & including LED lamp and making connection with copper flexible cable of appropriate size from ceiling rose to light fitting complete all as specified and directed. Make: Havells Cat Part No-LHEBFCP7IZ1W018 or Equivalent cat part of make as specified in Appx 'A' to P.S.

S&F in repair 2x2 LED edge-lit luminaire 36 watts suitable for armstrong/grid ceiling complete for low ceiling applications with driver and making connection with copper flexible cable of suitable size to light fitting complete all as specified and directed. Make:-Havells cat part No-STRATO2X2PLR36WLED857MOD for Module and cat part No-LEDDRIVER36V36WS for Driver or Equivalent cat part of make as specified in Appx 'A' to P.S.

S&F in repair 20 W LED tube rod 4 feet long with single side connection complete all as specified and directed. Make:-Havells Cat Part No:-LHLDEFXD5L8R020 for LED tube rod or Equivalent cat part of make as specified in Appx 'A' to P.S.

S&F in repair LED lamp CDL 10 watt with holder base (B22) type, complete all as specified and directed. Make of LED lamp:- Havells cat part No LHLDEUEEML8R010 or Equivalent cat part of make as specified in Appx 'A' to P.S.

S&F in repair LED driver suitable for 36 watt LED ceiiling light fittings and making connection to fitting complete all as specified and directed. Make:-Havells cat part No-LEDDRIVER36V36WS or Equivalent cat part of make as specified in Appx 'A' to P.S.

S&F in repair Single pole and neutral plastic enclosure with a two pin and earth plug and socket for surface mounting complete with one single pole MCB 20Amp 240V, complete all as specified and directed. Make:-Havells cat part No-DHDPHSN020 or Equivalent cat part of make as specified in Appx 'A' to P.S.

S&F Vertical distribution board TPN 4 ways with built in bus bars, neutral links, blanking plates double door suitable for FP MCCB as incommer and out going SP/TP MCBs with & including 63 Amps 4 pole MCCB having 16 KA breaking capacity complete all as specified and directed. Note:- MCCBs and MCBs shall be measured and paid separately. Make:-Havells cat part No-DHDLVDRWGOFO04 for DB and cat part No-IHLGNF0063 for MCCB or Equivalent cat part of make as specified in P.S.

S&F Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 4 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed. Make:- Havells cat part No-DHDPSHODPW04 or Equivalent cat part of make specified in PS.

S&F Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 8 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed. Make:- Havells cat part No-DHDPSHODPW08 or Equivalent cat part of make as specified in P.S.

S&F Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 12 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioningcomplete all as specified and directed. Make:-Havells cat part No-DHDPSHODPW12 or Equivalent cat part of make as specified in P.S.

S&F MCB TPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCTNF040 - DHMGCTNF063 or Equivalent cat part of make as specified in P.S.

S&F MCB SPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCSNF040 - DHMGCSNF063 or Equivalent cat part of make as specified in P.S.

S&F MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series complete all as specified and directed. Make:-Havells cat part No-DHMGCSPF006-032 or Equivalent cat part of make as specified in P.S.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing, complete all as specified and directed.

S&F Sub main wiring with single core cable 2x 6 sq mm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 2.5 Sq mm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including taking down old unsv sub main wiring of any type, complete all as specified and directed. Note:-2 wire of 6 sqmm, 1 wire of 2.5 sqmm and one run of pvc conduit/casing caping shall be measured as one unit.

S&F Sub main wiring with single core cable 2x 4 sq mm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 2.5 Sq mm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including taking down old unsv sub main wiring of any type, complete all as specified and directed. Note:-2 wire of 4sqmm, 1 wire of 2.5 sqmm and one run of pvc conduit/casing caping shall be measured as one unit.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat or circular of size 6 Sqmm with & including taking down old old unsv service cable connection, complete all as specified and directed.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat of circular of size 10 Sqmm including taking down existing old service connection, complete all as specified and directed.

Taking out old unsv exhaust fan from site of capacity 380/200 mm sweep and replacement of exhaust fan incl all connecting accessories complete all as specified and directed by Engineer-in-charge. Make: Havells/CG/Philips/Bajaj.

S&F in repair of PVC counduit non matalic rigid, of size 25 mm dia (external) incl all accessories use for fixing of conduit on wall and ceiling etc, complete all as specified and directed.

S&F in repair PVC casing caping of size 25 mm incl all fixing accessories complete all as specified and directed.

S&F in repair flexible PVC conduit of approved quality of size 25 mm dia bore with fixing materials complete all as specified and directed by Engineer-in-charge.

Repair and maintenance of unserviceable ceiling fan of 1200mm/1400mm sweep at contractor's work shop, incl dismantling complete the ceiling fan parts, inspecting serviceability of all the parts, refixing of serviceable parts after cleaning and replacement of unserviceable parts with company's genuine parts i.e. capacitor, bearing, bushes, shaft, bracket, rubber bush, connecting wire, PVC connector, aluminium clamp for rod, bracket, bush rod, greasing/oiling etc assembling, cleaning and testing of ceiling fan complete all as specified and directed. Note: (i) Unserviceable parts as above shall be measured and paid separately under relevant items of Sch 'A' as supply only. (ii) Rewinding of stator will be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. Cotter pin, screws shall be deemed to included in the cost of quoted rate.

S&F in repair bearing good quality for ceiling fan 1200mm/1400mm sweep ISI marked complete all as specified and directed.

S&F in repair Gun metal bush for ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

S&F in repair capacitor 2.5 mfd ISI marked complete all as specified and directed.

S&F in repair brass bracket assy for hanging the ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

S&F in repair 3 core flexible wire 40/.0076, white colour from ceiling rose to fan connector complete all as specified and directed.

S&F in repair stator shaft for ceiling fan complete all as specified and directed.

S&F in repair fan blade for ceiling fan 1200 mm sweep of existing make complete all as specified and directed.

All as per item No. 149 above but for ceiling fan 1400 mm sweep of existing make complete all as specified and directed.

S&F in repair canopy (top/bottom) of ceiling fans any make /size of colour matching with existing canopy/ fan colour complete all as specified and directed.

M&L for removing of old burnt winding of any size , type and rewinding of stator winding with superior quality copper wire with insulation complete all as specified and directed.

M&L for Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed.

M&L for Replacement of down rod of ceiling fan with down rod of 15mm bore medium grade GI pipe 0.45 metre long with clamps, bolts, nuts, split pins washers of suitable size of approved quality complete all as specified and directed by Engineer in charge.

All as per item No 154 above but of length 0.60 Mtr complete all as specified and directed.

Repair and maintenance of unserviceable exhaust fan of any cap and sweep by dismantling the exhaust fan parts, inspecting the serviceability of parts, refixing of serviceable parts after cleaning, replacement of unerviceable parts i.e. beaing, bush, capacitor, connecting wires, fan blade, locknut, rubber pad etc, oiling/greasing, cleaning and testing of exhaust fan complete all as specified and directed. Note: (i) Unserviceable parts replaced shall be measured and paid separately under relevant items of Sch 'A' as supply only. (ii) Rewinding of stator winding shall be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. screws shall be deemed to included in the cost of quoted rate.

Supply of double ball bearing (ISI marked) for exhaust fan of 200 mm sweep to 450 mm sweep fan complete all as specified and directed.

Supply of Gun metal bush for Exhaust fan of any cap. complete all as specified and directed.

Rewinding of 450mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

Rewinding of 300mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

S&F in repair blade of exhuast fan of 200 mm sweep to 450 mm sweep as per existing make complete all as specified and directed.

M&L for Preparation of painted surfaces of exhaust fan of any make and size by scrubbing old and applying one coat of synthetic enamel paint by spray painting complete all as specified and directed by Engr-in-Charge.

M&L for disconnecting elect & water connection to geyser of cap 25/50/35 ltr, taking down, from existing position, dismantling and inspecting all the parts, for its serviceability, cleaning of serviceable parts i.e. Heating elemet, base assy, connecting lead, thermostat, electrical contact, electric wiring, indicators, safety valves etc and refixing, replacement of unserviceable parts, re assembling, remounting, reconnecting with electrical & water connectionn and testing complete all as specified and directed. Notes: (i) The defective parts to be replaced shall be measured and paid separately under relevant item of Sch 'A' as supply only. (ii) Cost of minor items i.e. Screws, nut & bolts etc shall be deemed to be included in the above item.

S&F in repair heating element 2.0 KW, ISI marked with gasket suitable for as existing size, type and make of geyser complete all as specified and directed.

All as per item No 164 above but of cap 1.5 KW complete all as specified and directed.

S&F in repair thermostat ISI marked suitable for existing make of the geyser under repair of cap 50/25 /35 Ltrs complete all as specified and directed.

S&F in repair indicator lamp as per existing make and size complete all as specified and directed.

S&F in repair geyser safety valve (pressure release valve) for the exsiting make & capacity of geyser complete all as specified and directed.

S&F in repair geyser pipe connection heavy duty for inlet, outlet connection suitable to withstand the pressure and temperature for existing geyser complete all as specified and directed.

S&F in repair aluminium/cromium type flexible connection heavy duty for inlet, outlet connection suitable to withstand the pressure and temperature for existing geyser complete all as specified and directed.

S&F in repair inner tank made out of steel sheet conform to IS suitable for 25 ltrs capacity of geyser of different makes vertical type complete all as specified and directed.

All as per item No 171 above but for Geysers of capacity 35/50 ltrs complete all as specified and directed.

S&F in repair non return valve made out of brass fixed in veritcal complete all as specified and directed.

S&F in repair new base assembly with inlet and outlet pipe made out of steel base plate with gasket and proper size of nuts, bolts and washer etc suitable for 25 ltrs capacity of geyser complete all as specified and directed.

All as per item No 174 above but of size 35/50 ltrs complete all as specified and directed.

S&F in repair decorative flood light for fountain with multicolour LED bulb of IP 65 protection, 230 volt 50 HZ, water proof and rubber gaskit complete all as specified and directed. Make- havells/ CG /bajaj or as approved by GE.

Jiwan Singh

M/S NARAYAN CONSTRUCTION

M/s Liaqat Hussain Construction Company

M/S Jyoti Parkash Tilak Raj Gupta