CONSTRUCTION OF URP DANGER BUILDING AT AF STN AWANTIPUR (CEAFU-02/2018-19)

Amount

Total amount of Sch 'A' PART-I ( BUILDING WORK)

Total amount of Sch 'A' PART-II ( INTERNAL WATER SUPPLY AND PLUMBING WORK)

Total amount of Sch 'A' PART-III( Section-I) (EXTERNAL WATER SUPPLY WORK)

SCHEDULE `A' PART-III (Sec-II) (EXTERNAL WATER SUPPLY WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Cutting existing steel tubing for alteration or additions, 150 mm bore GI tubing complete all as specified and directed by Engineer-in-Charge.( Each cut measured).

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sound technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed .

Valve pit of internal size (0.9 x 0.9 x 0.9m) including necessary excavation and earth work as required for dismantling , reconstruction , foundation on complete all as specified including fixing of MS sheet 6 mm thick cover and angle iron frame with locking arrangement including two coats of synthetic enamel pain over a coat of red oxide primer on steel surface complete all as specified and directed by Engr-in-charge.

Total amount of Sch 'A' PART-IV(SEC-I)(SEWAGE DISPOSAL WORK)

Sch 'A' PART-IV (SEC-II) (SEWAGE DISPOSAL WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Construction of Soakage well, of internal size 2.4m dia and 3m deep ( brick masonry construction) complete all as specified and shown on drawings .Drg NO. CEAF/STD-15/2000 SH1/2 & 2/2

Construction of septic tank 25 users, Brick construction complete all as specified and as directed and shown on drawing. .Drg NO. CEAF/STD-15/2000 SH1/2 & 2/2

Total amount of Sch 'A' PART-V (SEC-I) (ROAD/HARDSTANDING /CULVERT/CAUSE WAY WORK)

Sch 'A' PART-V (SEC-II) (ROAD/HARDSTANDING /CULVERT/CAUSE WAY WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Chequered cement concrete tiles with white cement and pigments 300mm x 300mm x 25 mm thick, set, jointed and pointed in neat cement slurry in floors complete all as specified and as directed.

M&L hot thermoplastic imported road marking material strips conforming to British specification 3762 with 20% glass beads having reflective index of 1.5mm, 75% spherical with indigenous or for foundation plan having sufficient strength to withstand heavy load without deformation and having softening point 20 to 30 of area in width of n. exc. 15cm strip in white colour according to IRC 35-1970, complete all as specified and directed .

Total amount of Sch 'A' part-VI (AREA DRAINAGE WORK)

Total amount of Sch 'A' PART-VII (SEC-I) (SECURITY FENCING AND GATE WORK)

Sch 'A' PART-VII (SEC-II) (SECURITY FENCING AND GATE WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Total amount of Sch 'A' PART-VIII (Section-I) (INTERNAL ELECTRIFICATION WORK)

Sch 'A' Part-VIII (Section-II) (INTERNAL ELECTRIFICATION WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

S & F LED integrated batten T5 of 18/20Watt, 4 FT, white, indoor decorative PVC extruded T5 LED batten integrated type complete all as specified and as directed..

S&F high bay light fitting , 50W IP65 protection alongwith hanging hook clamp/surface mounted complete with all accessories prewired with and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed.

LED Street light of 25 Watt , IP66 powder coated pressure die cast aluminium compact high power LED street light with heat resistant toughened glass including connection electrically with twin core flexible cable with and including street light bracket made out of 40mm dia GI Pipe light grade 1.2 mtr long ,bent to shape, with all necessary fittings i.e nuts,bolts, clamps made out of flat iron 50X6mm -02 nos.and necessary electric connection complete all as specified and as directed by Engr-in-Charge.

S &F Surface mounted LED luminaire for mirror lighting 10 watt Complete with lamp including connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated sheathed with flexible copper conductor of size 0.50 sqmm all as required.

S &F Lamp holder insulated body with back plate ISI marked for batten fittings including LED 10 Watt complete all as specified and as directed.

S&F ceiling fan 1200mm sweep suitable to work on single phase 230 volts 50 Hz AC supply complete with electronic regulator step type hum free suitable to control speed of fan 0 to 100 % connecting electrically to ceiling rose or connector block using PVC insulated and over all sheathed 3 core cable of size 0.75 Sqmm with flexible copper conductor complete all as required at site complete all as specified and as directed .

S & F PVC exhaust fan (as per BEE recommendation) 250mm sweep single phase 230 volts 50 Hz AC supply totally enclosed heavy duty motor with die cast aluminium rotor mounted on two ball bearings complete louvers including cutting chases for fixing fan, connecting electrically using 3 core 0.75sq mm PVC insulated flexible copper conductor cable over all sheathed complete all as required at site or directed by Engr-in-Charge

Supply installation commissioning and testing of Busbar chamber 6 way 63 Amps indoor cubical floor mounted type made out of 2 mm thick MS sheet duly powder coated complete with bus bar 200 amps rating made of aluminium strip duly drilled holes for connections and mounted on epoxy based post insulators for 3 Phase 4 wire 415 Volts 50 HZ power supply system , with locking arrangement for front / rear door complete all as specified and as directed.

MCB single pole & neutral 240 volts 6 to 32 amps,with rupturing capacity 10 KA, complete all as specified and as directed. ISI Marked.

MCB single pole 240 volts 6 to 32 amps, with rupturing capacity 10 KA, ISI Marked

Total amount of Sch 'A' -IX (Section-I) (EXTERNAL ELECTRIFICATION AND COMMON NATURE ITEM WORK)

Sch 'A' Part-IX (Section-II)( EXTERNAL ELECTRIFICATION AND COMMON NATURE ITEM WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

M & L for cable route indicator made out of PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate , size of PCC block 150 mm X 150 mm X 50mm and MS bar 8mm for HT 11 KV underground cable complete all as specified and as directed.

S&F for Sub class `B' brick, well burnt, as in cable protection cover laid dry flat transversally over sand cushioning with width equal to the lengh of brick all as directed .

Design, Supply , instalation testing & commissioning of Extensible 11KV Ring Main Unit, Motorized, Indoor type with Three (3) 11KV Vacuum circuit Breakers with metering (01 Nos incomer and 2 Nos outgoing panels). Nominal Voltage 12KV, 630A, 25KA. HT Compartment-(circuit breaker T2)- Incomer Feeder (1 No) This function-unit consists of a vacuum-circuit breaker in combination with a three-position-switch. The three-position-switch fulfils the operation of the disconnector-function and the earthing- function. The circuit-breaker-unit T2 is equipped with an over current-time-release for the protection. Vacuum circuit braker 12KV, 630 A, 25KA/1s. (a) Spring assisted mechanism for motorized operation with integrated earthing switch-24V DC -1 No. (b) 1 Self powered Electronic numerical protection relay providing over-current & earth fault protection- Schneider Electric Infrastructure Limited Schneider make DPX- V5/CSPR-V5 relay:-1 No (c) 3 Ring core current transformer for protection & metering depending upon the transformer ratings 50/25/5A, 2.5 VA , Class 1.0/5P10 :-1 No (d) Capacitive voltage indication fixed type- LED display.1 No (e) ON,OFF, EARTH indication on the front mimic of the panel.1 No (f) Cable box for termination of cable up to 1 No. X 3C X 300Sqmm.1 No (g) Cable cover standard.1 No (h) Auxilliary contacts as per standard motorisation circuit.1 No (j) Emergency Trip Push Button.1 No (k) Shunt Trip Coil-24V DC:-1 No (l) MFM type EM 6400 with AC. CL. 1.0.:-1 No (m) Set of 12KV right angled type cable boots.(i.e. Terminal Protector):-1No

H.T.Compartment-(Circuit breaker T2)- O/G Feeder (2 No.) This function- unit consists of a vacuum-circuit breaker in combination with a three-position-switch. The three-position-switch fulfills the operation of the disconnector-function and the earthing-function. The circuit-breaker-unit T2 is equipped with an over current-time-release for the protection of Vacuum circuit breaker 12KV, 630A,25kA/1s. (a) Spring assisted mechanism for motorized operation with integrated earthing switch-24V DC.:-1 No (b) Self Powered Electronic numerical protection relay providing over-current & earth fault protection- Schneider Electric Infrastructure Limited Schneider make DPX- V5/CSPR-V5 relay.:-1 No (c) Ring core current transformers for protection & metering depending upon the transformer ratings 50/25/5A, 2.5 VA, Class 1.0/5P10:-3Nos (d) Capacitive voltage indication fixed type- LED display.:-1 No (e) ON,OFF, EARTH indication on the front mimic of the panel.:-1 No (f) Cable box for termination of cable up to 1 No. X 3C X 300Sqmm:-1 No (g) Cable cover standard.:-1 No (h) Auxilliary contacts as per standard motorisation circuit.:-1 No (j) Emergency Trip Push Button.:-1 No (k) Shunt Trip Coil-24V DC.:-1 No (l) MFM type EM 6400 with AC. CL. 1.0:-1 No (m) Set of 12KV right angled type cable boots.(i.e. Terminal Protector):-1 No

Integrated bus connected PT Metering Cubicle (a) Three Phase PT of ratio 11kV/root 3/110V, 50 VA,CI 0.5 with HT fuses on the primary side and MCB on secondary side.:-1 No (b) Space Heater with thermostat:-1 No (c) RYB indicating lamps:-1 No (d) PLC Autochangeover kit:-1 No (e) Additional equipment delivered separately or mounted separately or mounted in respective panel. (f) Standard Manometer:-1 No (g) Motorized Operating Handle:-1 No (h) Battery 24V DC & 12 AH and Battery Charger 5A.:-1 No (j) Cable clamping provision (standard):-1 No (k) Operation and Installation Manual.:-1 No (l) Installation & Commissioning Manual.:-1 No

Supplying, installing, testing & commissioning of factory assembled silent Diesel Engine driven generating set 1500 RPM of capacity minimum 500 KVA (NTP), 3 phase, 4 wire,415 volt, 0.8 PF, complete with control panel including integrated powder coated acoustic enclosure as per CPCB regulations and duly certified by agencies/labs designated by CPCB for noise and sound pollution level, etc floor mounted including PCC foundation suitable to accommodate DG Set and AMF Panel inside, including minimum space of 1.5 mtr for ease of operation and maintenance on each side complete all as specified and directed and comprising of the following :- (A) DIESEL ENGINE of capacity as per manufacturer design but not less than 580 BHP for driving 500 KVA alternator multi cylinder, vertical type, 4 stroke, water cooled, electric start continuous running capable of taking 10% overload for one hour in 12 hours complete and comprising of Radiator assembly, radiator fan, Flywheel with starter ring, water pump assembly, Fuel Injection pump, Fuel filter, Lub oil filter, Air filter, Water oil separator, Exhaust silencer including wounding Asbestos rope on Exhaust pipe upto exhaust out let, Governing class G3 as per ISO 8528 Part-V(for Kirloskar or equivalent in other makes), Electric start, including self-starter operated at DC Voltage as per manufacturer recommendations including battery/set of batteries each of 12 Volts and AH as per manufacturer recommendations, Fuel tank of capacity suitable to run Engine on full load upto 08 Hrs or as per manufacturers recommendations, including lub oil sump, and including first complete filling of lub oil and coolant, Minimum 8 cylinders but not less than specified, including turbo charger,

Battery Charging Alternator pre-wired complete and other protection accessories as per manufacturer recommendation, all as specified and directed (B) ALTERNATOR shall be self-excited, self-regulated, brush less for 500 KVA continuous operation at the speed of 1500 RPM at 415 volts, 50Hz , three phase four wire system with advance electric voltage regulator to ensure voltage accuracy with + 1% with proper insulation and directly coupled with engine and confirming IS- 4722 or IEC- 34-1 complete- 1 No. (C) Common fabricated base frame for engine & alternator made from structural Steel channel, jerk proof on PCC 1:2:4 type B1 foundation including adequate number of anti-vibration pads in adequate quantity all as per the recommendation of the manufacturer(Note:- Cost of suitable size of PCC foundation is deemed to be included in the unit rate quoted by the contractor. (D) Bottom mounted Fuel tank of MS sheet of capacity not less than 8 Hrs continuous operation, inside canopy, with fuel level gauge, drain plug, locking arrangements, etc including connection to Engine through fuel filter/ manual feed pump as per manufacturer recommendations. (E) ENGINE INSTRUMENT PANEL : (a) Digital type controller able to display:- Alternator voltage, Battery voltage, Load Current, Fuel level, Lub oil pressure, Frequency, RPM and able to stop generator on any fault and to display parameters, i.e, Low battery, LLOP, Under voltage, Over Voltage, High Engine Temperature, Battery charging failure and other protections as per manufacturer recommendations including necessary wiring set of relays, MCB/Fuse etc. (b) Engine start and stop switch (c) Emergency stop switch (d) DC Power supply suitable for controller and Battery charging.

M&L earthing complete with galvanised steel earth plate electrode 60cmx 60cm x 6mm thick burried directly in ground ( earth pit not less than 2.25 mtr below normal ground level ) connected to and including galvanised iron strip 32x6mm by means of bolts nuts check nuts and washers of galvanised iron or steel including PCC pit in PCC 1:2:4 type B-1 RCC cover made out of cement concrete 1:2:4 type B-1 (using 20 mm grade crushed stone aggregate) reinforced with TMT steel bars 8 mm dia @100 mm c/c both ways with suitable handle and angle iron 40x40x5mm frame, GI medium grade watering pipe 20mm bore and funnel with wire mesh light grade protection pipe 40mm bore upto main board complete as shown on electrical plate No 3 of MES Sch 2009 (Part-I) and testing on completion all as directed. Note: (i) On testing after completion of earthing, if desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk & cost to the entire satisfaction of Engineer-in-charge. (ii) GI strip & GI protection pipe up to 7.5 metre is deemed to be included in the unit rate quoted against this item .

S&F installation testing and commissioning of LT electric panel board, floor mounted totally enclosed (Factory, Fabricated), indoor type single door type powder coated inside & outside made out of CRCA sheet not less than 3mm thick with front opening having locking arrangement spray painting in ORANGE colour externally, written as MASTER SWITCH externally including internal wiring with suitable size consisting of the following:- (a) MCCB 630 A, 4 pole 50 KA-01 No.

Supply and fix LED street light fittings 120 W IP 65 including LED lamp and twin core flexible copper conducter cable to connect electrically to junction box complete all as specified and directed. Note :- Bracket for fixing OF LED light and twin core flexible copper conductor cable will be measured and paid for separetely.

Supply & fix, bracket for fixing of LED light on pole made out of 50 mm dia G.I pipe 1.2 mtr long bent to shape/angle as required on site with suitable type of MS clamp of size 40mmX5mm thick MS flat nuts, bolts and washers, duly painted , complete all as specified and as directed by the Engr-in-Charge.

S&F in replacement PVC insulated, sheathed, multi stranded, three core, 1100 volts grade copper conductor cable of size 2.5 sqmm complete all as specified and as directed.

Supply and fixing junction box of 300X300X200mm with 50 Amp bus bar & 1 No MCB SP 10 Amps including MS clamp etc complete all as specified and as dircted.

Supplying, installation testing, commissioning electric Motor siren conforming to IS-1941, suitable for 3 Phase 415 Volts & supply with motor not exceeding 3.75 KW Power and able to deliver 143 DB noise level complete all as specified and as directed .

M&L earthing complete with copper earth plate electrode 30cmx 30cm x3mm thick burried directly in ground ( earth pit not less than 2.25 mtr below normal ground level ) connected to and including copper strip 25x3mm by means of bolts nuts check nuts and washers of galvanised iron or steel including PCC pit in PCC 1:2:4 type B-1 RCC cover made out of cement concrete 1:2:4 type B-1 (using 20 mm grade crushed stone aggregate) reinforced with TMT steel bars 8 mm dia @100 mm c/c both ways with suitable handle and angle iron 40x40x5mm frame, GI medium grade watering pipe 20mm bore and funnel with wire mesh light grade protection pipe 40mm bore upto main board complete as shown on electrical plate No 3 of MES Sch 2009 (Part-I) and testing on completion all as directed. Note: (i) On testing after completion of earthing, if desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk & cost to the entire satisfaction of Engineer-in-charge. (ii) Copper strip & GI protection pipe up to 7.5 metre is deemed to be included in the unit rate quoted against this item .

Total amount of Sch 'A' part-X (SITE CLEARANCE , EXCAVATION AND EARTH WORK)

Total amount of Sch 'A' PART-XI (Section-I) (LIGHTENING PROTECTION WORK)

Sch 'A' PART-XI(Sec-II) (LIGHTENING PROTECTION WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

M&L earthing complete with galvanised steel earth plate electrode 60cmx 60cm x6mm thick burried directly in ground ( earth pit not less than 2.25 mtr below normal ground level ) connected to and including galvanised iron strip 32x6mm by means of bolts nuts check nuts and washers of galvanised iron or steel including PCC pit in PCC 1:2:4 type B-1 RCC cover made out of cement concrete 1:2:4 type B-1 (using 20 mm grade crushed stone aggregate) reinforced with TMT steel bars 8 mm dia @100 mm c/c both ways with suitable handle and angle iron 40x40x5mm frame, GI medium grade watering pipe 20mm bore and funnel with wire mesh light grade protection pipe 40mm bore upto main board complete as shown on electrical plate No 3 of MES Sch 2009 (Part-I) and testing on completion all as directed. Note: On testing after completion of earthing, if desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk & cost to the entire satisfaction of Engineer-in-charge. NOTE:- Galvanised iron strip 32X 6 mm & 40 mm bore light grade protection pipe up to 7.50 metre is deemed to be included in the unit rate quoted against this item.

Sch 'A' Part-XII (FLAME PROOF EOT CRANE WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Design, supply, installation, testing and commisioning of 2 Ton capacity flame proof EOT crane, electrically operated through pendant push button station floor operated type having hoisting height of 5 meters from FFL approximately complete with and including main frame, crab, buffers, gears with gear boxes, shafts, rope drum, rope sheaves, wire rope, wheels, lifting hook, brakes, motor, limit switches, control panel, pendant push button station, micro speed arrangements, wiring etc. IS-3177 and IS-807 all as specified below:- (a) Capacity 2.0 Ton (b) Cross Span 8 meters approximately (c) Long Span 135 metres approximately (d) Hoist lift 5 metres approximately from FFL. (e) Hoisting Speed 3m/min approximately and creep/micro speed 0.3 metre per minute (f) Hoisting motor of suitable HP as per design calculation submitted by Contractor through OEM . (g) Cross travel speed -10mpm and creep/micro speed 0.3 metre per minute . (h) Cross travel motor of suitable HP as per design calculation submitted by Contractor through OEM . (j) Long Travel speed -10 mpm and creep/Micro speed of 1 metre per minute (k) Long Travel motor -1/2 Nos of suitable HP as per design calculation submitted by contractor . (l) Operation pendent Push button from floor . (j) Class of duty - II (indoor).

Design, supply, installation, testing and commisioning of 2 Ton capacity flame proof EOT crane, electrically operated through pendant push button station floor operated type having hoisting height of 3.5 meters from FFL approximately from FFL complete with and including main frame, crab, buffers, gears with gear boxes, shafts, rope drum, rope sheaves, wire rope, wheels, lifting hook, brakes, motor, limit switches, control panel, pendant push button station, micro speed arrangements, wiring etc. IS-3177 and IS-807 all as specified below:- (a) Capacity 2.0 Ton (b) Cross Span 4 meters (c) Long Span 7 metres (d) Hoist lift 3.5 metres from FFL. (e) Hoisting Speed 3 mpm and creep/micro speed 0.3 meter per minute. (f) Hoisting motor of suitable HP as per design calculation submitted by Contractor through OEM (g) Cross travel speed -10mpm and creep/micro speed 0.3 meter per minute. (h) Cross travel motor of suitable HP as per design calculation submitted by Contractor through OEM (j) Long Travel speed -10 mpm and creep/Micro speed of 1 meter per minute (k) Long Travel mptor -1/2 Nos of suitable HP as per design calculation submitted by contractor . (l) Operation pendent Push button from floor . (j) Class of duty - II (indoor).

Gantry guider with square bars etc for 7 metre long span bay length inside the bins complete all as specified and shown on drawings

Gantry guider with square bars etc for 135 metre bay length for out side operation complete all as specified and shown on drawings

Supply and Fix flameproof and weather proof MCB socket & plug combined, of rating 32 A , 415 volt 3 Pt earth complete all as specified and shown on drawings

Total amount of Sch 'A' PART-XIII(Sec-I) (FLAME PROOF INTERNAL ELECTRICFICATION WORK)

Sch 'A' Part-XIII (Sec-II) (FLAME PROOF INTERNAL ELECTRICFICATION WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

S&F for explosion proof point wiring with 1.5 Sqmm 1100 Volts grade PVC insulated fire retardant multi stranded flexible copper coductor cable in and including ERW rigid steel conduit steel conduit ISI marked with all flame proof conduit fittings and accessories fixed on walls/ceiling with proper fixing arrangements including one No continuous run of 1.5 Sqmm PVC insulated fire retartdent solid copper conductor cable as earth continuity conductor fixed to earth terminal and metallic body of light fittings/fan and socket etc complete all as suitable for Class Zone IE Ex II C for one light point controlled by One way switch compete all as specified and as directed.

M&L for explosion proof submain wiring with two single core grade PVC insulated fire retardant multi stranded flexible copper conductor cable of size 4 sqmm in and including ERW rigid conduit ISI marked with all flameproof conduit fittings and accessories fixed on walls/ceiling with proper fixing arrangements including one no. continuous run of 4 Sqmm PVC insulated fire retardant solid copper conductor cable as earth continuity conductor fixed to earth terminal and metallic body all as specified and as directed. Note:- 3 run of 4 sqmm copper conductor cable will be measured as 1 unit RM.

Supply & Fix flame proof sheet metal enclosure MCB distribution board doubledoor Three pole & neutral 240 volts 4 way conforming to IP 66 complete including incoming 40-63 Amp TPN and outgoing SPN 6-32 Amp and capacity all as specified and directed. Note: MCB DB and MCB to be integrated for flameproofing by contractor from manufacturer before installing.

Supply and fix flameproof sheet metal enclosure MCB distribution board double door single pole & neutral 240 Volts 4 way conforming to IP 66 complete including incoming SPN and outgoing SP of suitable size and capacity all as specified and directed. Note: MCB DB and MCB to be integrated for flameproofing bycontractor from manufacturer before installing

SCHEDULE `A' PART-XIV (CENTRAL AIR HEATING SYSTEM AND COOLING WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only. Note :- (a) HVAC schedule given in tender is tentative for reference only . Contractor will submit his own design duly vetted by IIT/NIT .The capacity of plant and equipments will not be less than capacity indicated in Schedule “A”/BOQ , PS and drawing. (b) If design approved by IIT/ NIT require higher capacity, the same will be provided by the contractor and cost of the same is deemed to be included in rate quoted by the contractor in Schedule ‘A’/BOQ . NO deviation for higher capacity will be admissible on this account . Capacity of plant is deemed to be amended on higher capacity without any extra cost to the department which is required to the supply , installation , testing and commissioning of entire plant to achieve desired condition of temperature and humidity indicated in Sch “A”/BOQ & PS during outside conditions of peak summer, winter and monsoon respectively . (c) Capacity indicated in schedule or the higher capacity suggested by IIT / NIT shall be achieved , tested and guaranteed on ground at outlet /discharge side of equipments like hot Glycol Generator , chiller , pump , AHU, cooling tower etc by the contractor.

Water Cooled Centrifugal Chiller/scroll chillers Supply, Installation, Testing and Commissioning of ARI/Eurovent Certified 50 TR (Actual)Cooling capacity Water Cooled Centrifugal Chillers/scroll chillers having hermetic/Semi hermetic/Open, single/multi stage Compressor 50TR cooling capacity , refrigerant/ fan cooled motor , Motor suitable for 415 ± 10% volts, 50 Hz, 3 Phase Power Supply, Factory Fitted Unit , Microprocessor Based Control Panel, suitable for low GWP/ODP/Flammability/toxicity Refrigerant, Shell & Tube Insulated Evaporator, Shell & Tube Condenser, Electronic Expansion Device, Suitable Capacity Control Mechanism etc. Chilled Water Entering Temperature : 18 deg C Chilled Water Leaving Temperature : 6 deg C Evaporator Fouling Factor : 0.0001 MKS Condenser Water Entering Temperature : 32 deg C Condenser Water Leaving Temperature : 65 deg C Condenser Fouling Factor : 0.0002 MKS Refrigerant : low GWP/ODP/Flammability/toxicity Refrigerant Maximum Allowable IKW / TR @ 100% Load : 0.67 Maximum Allowable NPLV : 0.4 Scope of Supply for each chiller:- (a) 50 TR coolong capacity Centrifugal,scroll,screw, hermetic/Semi Hermatic/Open compressor complete with automatic capacity control, safety switches and controls etc. as per specifications.- 01 No

(b) . - Suitable capacity air cooled induction motor with class 'F' insulation suitable for operation on 415± 10% volts, 50Hz, A.C. supply.:-1 No (c) 1No. - Matching shell and tube water cooled condenser of M.S. shell and integrally finned copper tubes.:-1 No (d) 1No. - Matching flooed Type shell and tube chiller of MS shell & and copper tubes.:-1 No (e) Refrigerant piping fittings, valves and accessories to interconnect compressor, condenser, chiller and electronic expansion valve.:-1 No (f) Microprocessor based control panel complete with accessories as per specifications.:-1 No (g) Refrigerant line accessories comprising of safety valves, angle valve, liquid line indications etc.. (h) Water flow switches at outlet of condenser and chiller, water drain and air purge valves where ever required. (j) Suction line and chiller insulation with suitable thickness Croos linked XLPE insulation complete as required. (k) Frame work for mounting the above condenser, chiller compressor and motor with base plate complete with anti-vibration pads/springs. (l) Interconnecting piping with valves duly insulated. (m) Victolic coupling for Pipes (Chiller/Condenser) connection. (n) RCC cement concrete foundation for the chiller unit. (2 Working + 1 Standby)

Condenser Water Pumping System Supply,Installing, testing and commissioning of pumping system consisting of horizontal suction and delivery condenser water pump sets capable of delivering total 150 USGPM of water against 25 meter head and complete as per specification. The system shall comprise of the following: (a) Centrifugal pump with minimum 75% efficiency. 150 USGPM delivery at 25 M head suitable for parellel operation speed 1500 RPM.:-2 No. (b) Suitable HP TEFC squirrel cage induction motor with class 'F' insulation, 1500 rpm synchronous speed, operating on 415+ 10% volts, 3 phase, 50 Hz A.C. supply:-.2 No. - (c) Mounting frame with Antivibration pads. (d) Interconnecting piping with valves . (e) RCC cement concrete foundation for the pump unit. (1 Working + 1 Standby).

Hot/Chilled liquid Pumping System Supply,Installing, testing and commissioning of pumping system consisting of horizontal suction and delivery Hot/Chilled liquid pump sets capable of delivering total 135 USGPM of water against 25 meter head and complete as per specification. The system shall comprise of the following: (a) - Centrifugal pump with minimum 75% efficiency. 135 USGPM delivery at 25 M head suitable for parellel operation speed 1500 RPM:-2 No. (b) Suitable HP TEFC squirrel cage induction motor with class 'F' insulation, 1500 rpm synchronous speed, operating on 415 ± 10% volts, 3 phase, 50 Hz A.C. supply:-2 No (c) XLPE insulation of suitable thickness duly cladded by aluminium sheets of 0.5mm thickness and properly clamped to pump as per specifications. (d) Mounting frame with Anivibration pads. (e) Interconnecting piping with valves duly insulated. (f) RCC cement concrete foundation for the pump unit (1 Working + 1 Standby)

Cooling Tower 125 TR Combined heat rejection capacity Supplying, installation, testing and commissioning of FRP cooling tower of 125 TR heat rejection capacity each, in cell construction with FRP water basin, PVC fills with integral louvers and drift eliminators complete with hot water basin either fitted with spray nozzles or having self rotating sprinklers, statically and dynamically balanced axial flow type fan-direct driven or driven through reduction gear box with TEFC induction motor, suction screen, make up-quick fill arrangement, overflow and drain connections with necessary valves and suitable inspection ladder, access arrangement for cooling tower interior, cement concrete foundation, steel / masonry supporting structure, anti-vibration mountings, complete as per specifications and as required.

AIR HANDLING UNITS/AIR WASHER UNIT:- Supplying, installation, testing and commissioning of factory built floor mounted chilled water double skin type Air Handling Units/AIR WASHER UNIT made of 25mm thick panels consisting of G.I. Casing of thickness 0.8 mm outside layer and 0.8 mm inside layer with polyurethene foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower suitable for static pressure as detailed below, cooling coil section with machanically bonded aluminium finned copper tubes ( tube thickness not less than 0.5 mm ) cooling coil, filter section with pre filter 90% efficiency and down to 10 micron, direct drive package with flame proof TEFC drive motor suitable for 415± 10% volts, 50 Hz, 3 phase, A.C. supply, drain connections, with stainless steel drain pan duly insulated , and necessary vibration isolation arrangement etc. complete as per specifications and drawings of following capacities:-

AHU :- 25 TR, Row coil filter bank 1-MERV 7 , filter bank 2- MERV 14 , 5000 CFM suppy air fan , static pressure of all fan 65 mm of WG.

Air washer Unit:- RETURN AIR washer FAN 5000 CFM, STATIC PRESSURE OF ALL FANS 65 MM OF WG Note:- Motor and cabling/wiring should be flame proof type

Chilled Water Circuit Piping Supply,installation,testing and commissioningof "C"class mild steel Chilled water piping with all necessary fittings like bends , tees,reducers,flanges,supports and duly insulated with Closed Cell FR-XLPE thickness as given below. The joints shall be sealed with 50 mm X 1 mm thick self adhesive tape complete as per specifications.

100 mm dia.(25 mm thick insulation) Note:- 1- Pipe outside the building shall be cladding with 0.5 mm thick aluminium sheet as per specification. 2- Pipe inside the building shall be covered with woven fiber glass fabric of 5 mm thickness (140 Grams/Sq.Mtr.) and Coated with fire rated vapor barrier preferably epoxy resin or acrylic compound as per specification.

Valves:- Supply,installation,testing and commissioning of following PN-16 valves, stainers gauges in the chilled water piping duly insulated to the same specifications as the connecting piping and adequately supported as per specification and drawings . The chilled water circuit with all fittings and insulation with cladding as per the drawings and specifications.

Butterfly valve of size 100 mm dia.

Balancing Valve of size 100 mm dia.

Check valve of size 100 mm dia.

Y- Strainer of size 100 mm dia.

Pressure guage

Thermometer

Three-Way Modulating Valve Supply,Installing, testing and commissioning of complete control for AHUs comprising of a set of 3- way modulating proportional linear type valve having manual overried facility with Proportionate thermostate and wiring for interconnection with 1.5 sq.mm copper conductor multicore armoured cable suitable for Heating /Cooling complete as per specifications and as required.

80 mm dia for AHUs

Flow Meter (Digital)

Pressurized Chilled Water expansion Tank:- Supply,Installation, testing and commissioning of PRESSURISED CHILLED/HOT WATER EXPANSION TANK suitable for total volume of water in chilled water circuits along with necessary accessories such as solenoid valve, safety valve, pressure switch with connection to chilled water header and pressurization unit . Note:-(i). The tank must be constructed in accordance with section VIII of the ASME Boiler and pressure vessel code and stamped 6 Kg /cm2 working pressure. The complete system shall be sourced from single manufacturer and supplied and installed with all accessories and safety fixtures required for proper functioning of the complete hydronic system. The Contractor shall calculate the total volume of water and determine the expansion tank capacity. (ii).Chilled water Expansion Tank suited for above application for proper functioning of the complete hydronic system. The total approximate Volume of water in chilled water circuit = 500 gallons and static head of approximate 25.0 mtr to be considered . The contractor shall submit calculations for total system volume Tank & accessories as above (iii) Mounting frame with Anti vibration pads. (iv) Interconnecting piping with valves duly insulated.

Air Separator: Installation, testing and commissioning of AIR SEPARATOR along with necessary accessories such same to prevent entrapment of air in the system. The separator must be constructed in accordance with Section VIII ASME boiler and pressure vessel. Air Separator Connection shall be suitable for 100 MM dia pipe. Air Separator as described above (i) Mounting frame with Ant vibration pads (ii) Interconnecting piping with valves duly insulated complete all as specified and as directed .

Drain Piping Supply,installation,testing and commissioning of GI B Class drain water piping on floor / ceiling of following size along with necessary clamps, fittings such as bends tees etc. and duly insulated with closed cell FR-XLPE thickness as given below. The joint shall be sealed with 50 mm x1 mm thick self adhesive tape complete as per specifications. of 25 mm dia (9 mm thick .)

Condenser Water Circuit Piping Supplying, fixing, testing and commissioning of 'C' Class mild steel condenser water piping with all necessary fittings like bends, tees ,reducers, flanges, supports as given below complete with vibration isolators as per specification of 150 mm dia.

Valves:- Supplying, fixing, testing and commissioning of following PN - 16 valves, gauges and strainers for water circulation as per specifications. Supply,installation,testing and commissioning of following PN-16 valves, stainers gauges in the condenser water piping and adequately supported as per specification and drawings . The condenser water circuit with all fittings as per the drawings and specifications.

Butterfly valve of size 150 mm dia.

POT-Starainer of size 150 mm dia.

Y- Strainer of size 150 mm dia.

Pressure Gauge on all incoming and outgoing of chilled water and condensor water piping for Chiller, AHU Cooling coil etc

Thermometer on all incoming and outgoing of chilled water and condensor water piping for Chiller, AHU Cooling coil, Cooling Tower etc.

DUCTING AND GRILLES Ducting work (for Air Conditioning) Supply, installation and testing of Factory / Site fabricated GI sheet metal ducts as per IS: 655 and IS:277 in accordance with the approved shop drawings and as required by the specifications.

24 Gauge

22 Gauge

20 Gauge

18 Gauge

Duct Insulation Supply,installation,testing and commissioning of fire retardant insulation material of suitable thickness of thermal conductivity as per specification (Joint shall be sealed with self adhesive tape). Aluminum sheet wrapped 50 mm thick minimum.

50 mm thick

Supply Air Grilles Supply, installation, testing and balancing of powder coated Extruded Aluminium supply air Grilles with volume control dampers in accordance with the approved shop drawings and specifications.

Return/Exhaust Air Grilles Supply, installation, testing and balancing of powder coated Extruded Aluminium Return/Exhaust air Grilles with volume control dampers in accordance with the approved shop drawings and specifications.

Fresh Air Grilles Supplying, fixing, testing and commissioning of powder coated extruded aluminium section fresh air grill in weather maker room with aluminium volume control dampers, bird screen etc complete as required.

Fresh Air Intake/Exhaust Air Louvers Supply, installation, testing and balancing of Powder coated/Anodised extruded aluminium construction inlet air louvers with bird screen and volume damper for fresh air as per specifications and approved shop drawings.

Supply, fixing, testing and commissioning of fire dampers in supply air ducts / main branch and return air path as & where required of required sizes including control wiring. The spring return action shall be built mechanism and not externally mounted. as per specifications of STEC no 22 as required.

Fire Damper

Power Cabling. Supply, installtation testing and commissioning of complete cable work using XLPE insulated PVC sheathed steel tape/ wire armoured underground aluminium/copper conductor cables of following size for electric supply from main panel in AC plant room to various loads including Supplying and making end termination with brass double compression glands and aluminium lugs including interconnections from starters to motors on existing cable trays/supports as required as per specifications .

3.5 core x 25 Sqmm -copper armoured cable

3 core x 10 Sqmm -copper armoured cable

3 core x 6 Sqmm -copper armoured cable

3 core x 4 Sqmm -copper armoured cable

Control Cabling Supply,installation,testing and commissioning of complete cable work using PVC inulated PVC sheathed copper control cables of following sizes to various equipment including interconnections from electric supply to equipments on existing cable trays / supports as required including end termination on both sides as per specifications and as required.

6 Core 1.5 sqmm -Copper Cable

Cable Tray:- Fabrication and installation of following size of perforated GI cable tray, including horizontal and vertical bends reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with MS suspenders including painting etc.as required.

300 mm W x 1.6 mm thick

150 mm x 1.6 mm thick

Earthing

Providing & fixing 6 SWG dia. GI wire on surface or in rececess for loop earthing complete as required.

Providing & fixing 25mmx5mm GI strip on surface or in rececess for earth connections etc complete as required.

Supply, Installation ,commissioning and testing of complete in all respect central air heating system and cooling system including boiler unit, chiller unit, AHU, Pipe line etc as per design conditions mentioned below :- (A) Supply, Installation, commissioning and testing of Central Air Heating plant using HSD oil fired pressurized type 3 Pass reverse flame horizontal smoke TubeTwo numbers hot water boiler of not less than 5,00,000 K Cal/Hr each complete to meet the required condition of temp and humidity criteria for building complete in all respect, with combustion chamber and equipment automatic monoblock burner assembly, fire tubes, control panel with sequence controller, photo cell for frame failour, HT transfer electrode blower assembly electric panel, mounting frames, pressure guage at inlet and outlet for suitable operation on 50 Hz three/single phase AC supply complete in all respect including following item of work. Make: Thermax, Ecoflame, Western,Rapidtherm, Alphatherm Note :- (I) The boiler shall be installed in system of (1W+1 S) (ii) The tenderer should get the plant installed by any of the original equipment manufacturer with recommended makes of compatible components of items. (iii) The boiler minimum specification should be as under: Countd...

(i) The boiler inner shall be made from min 8mm thick carbon steel with dish end (curve type) (ii)Outer shell made from min 6mm thick carbon steel iii) Boiler tube shall be made from 50 mm dia, min 3.66mm thick , seamless MS Tube (boiler quality) (iv) The front door shall be openable lined with high grade insulation and refactory. (v)High efficient, low noise imported monoblock burner (Benton/Rello) (vi) The boiler shall be insulated with 50mm thick resin bonded fibre glass wool and cladded with 22 guage GI sheet (epoxy painted) (vii) Pre wired control panel (made from 18 guage CRC sheet ) Main incomer, MCB in/out temperature controller (digital)fault indicating light for water high temp, burner trip,flue temp, with alarm, hour meter for maint schedule etc. (viii) 1 set of oil piping from unit to burner . (ix) Suitable concrete foundation of boiler . (a) Heater unit:-Heat exchanger ,consisting of closely wound, helical concentric coils, arranged to give adequate no. of passes on flue gas side & made out of ERW tubes confirming to IS 3059 Part-I suitable for high temperature all as per manufacturer design and of required head and capacity . Countd..

(b) Pressure jet burner:-Suitable for light oil firing with stepless modulation mechanism all as per manufacturer design and of required head and capacity. (c) Combustion air fan with drive motor assembly all as per manufacturer design and of required head and capacity. (d) Control Panel : Dust protected pre-wired unit mounted air cooled control panel housing a burner management system , switchgear consisting of contactors, overload relays, fuses and MCB etc.all as per manufacturer design and of required capacity. ( B) Design,supply, installation and erection of Chimney 10 mtr height (chimney above bldg roof ) made out of min 3 mm thick MS sheet including flue gas duct all as per recommendation of manufacturer of Central Air Heating plant of above referred item. Qty - 02 Nos ( for each Boiler) ( C) Design ,supply and Installation of Glycol storage tank of capacity 2000 ltr made out of 5mm thick MS sheet complete all as specified and as directed. Qty - 02 Nos ( D) Design ,supply and Installation of diesel fuel storage tank of capacity of 1000 ltr made out of 5mm thick MS sheet complete all as specified and as directed. Qty - 01 No.

Day oil storage tank: Supply installation testing and commissioning of HSD Oil Day Storage tank rectangular mild steel IS 2062 construction with capacity of 2000 Ltr complete with inlet outlet overflow , drain vent with flame arrester. Tank shall be made out of 4mm thick MS sheet and will be provided with supports made out of minimum 50 mm dia medium grade pipe to keep tank base at minimum 2500 mm above finished floor level. The tank shall be provided with level switches for on/off operation of transfer pump. Extra high level and low level alarm shall be provided alongwith gauge indicator duly calibrated. Tank and structure shall be painted with the two coats with synthetic enameled paint of approved color over one coat of primer complete all as specified

Transfer gear oil pump fuel (Self priming): Supply installation testing and commissiong of self priming rotary gear transfer pumps of capacity 15 LPM 10 mtr Head for Kerosene or HSD oil complete with base mounting frame. PCC foundation including holding down bolts, coupling guard and TEFC flame proof motor 2 HP and other accessories required for commissioning etc complete all as specified and directed.

Glycol based water fluid tank: Supply and installation 2000 ltr capacity MS tank made of 3 mm thick mild steel cylindrical/ rectangular with removable lid, in/out/drain/overflows system mounting arrangement making connections etc complete all as specified and directed IS marked.

Total amount of Sch 'A' Part-XV(Sec-I) (FIRE FIGHTING SYSTEM WORK)

Sch 'A' Part-XV (Sec-II) (FIRE FIGHTING SYSTEM WORK) Note : This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

S&F 2 Core X 1.5 Sq.mm multistrand armoured copper cable with all accessories and complete in all aspects, complete all as specified and as directed . Note:- (i) The cable shall be having cable pointer at every meter . (ii) These cables shall be used for the wiring of detectors and devices.

2 Core X 2.5 Sq.mm multistrand armoured copper cable with all accessories and complete in all aspects, complete all as specified and as directed . Note:- (i) The cable shall be having cable pointer at every meter . (ii) These cables shall be used for the wiring of detectors used for the wiring of detectors and devices.

Supply and installation testing and commissioning of repeater panel complying with BS EN 45 suitable for wall mounting conforming to IS -2189 fabricated out of 16 guage CRCA sheet incorporating audio visual indication including dry type maintenance free battery of suitable capacity and battery charger complete all as specified and as directed

M/S HASSAN ROAD CONSTRUCTION COMPANY PVT LTD.

M/S GHULAM AHMAD WANI