NIT No GE/ND-95/2025-26

Amount

B&R PORTION: Dismantling floor, hearth or wall tiling, interloking , paver block any type or pattern including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for super gloss vetrified floor tiles of size (600mm X 1200mm), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L for super gloss modern floor tiles of size (600mm X 1200mm) as in skirting laid on 10mm thick cement plaster in CM (1:3) , set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cement to match the shade of tiles complete all as specified and directed by Engr in charge.

M&L for 600x600mm vetrified tiles in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in CM 1:4 complete all as specified and directed.

M&L for 600x600mm vetrified tiles as in skirting laid on 10mm thick cement plaster in CM (1:3) , set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cement to match the shade of tiles complete all as specified and directed.

M&L for 600x600mm matt finished vertified tiles in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in CM 1:4 complete all as specified and directed.

M&L for super glossy degital wall tiles of approved colour and design in vertical surfaces 600mmx1200mm thick including provision of high lighter tiles/boarder and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.

M&L for Glazed degital ceramic tiles of approved colour and design in vertical surfaces 600mmx300mm thick including provision of high lighter tiles/ boarder and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.

All as per item No 08.00 above but of size 600x1200 complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (40mm graded stone aggregate) as in mass concrete complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc including removal of debris from the MOD land complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:6 on internal brick/concrete wall surfaces of any description, and finishing the surfaces even and fair without using extra cement complete all as specified and directed .

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and fair without using extra cement complete all as specified and directed by Engr in charge.

M&L for preparation of the newly plastered surfaces of walls applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats Distempering with, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and directed.

M&L for preparation of old decorated surface (plastered or unplastered) of walls by complete removal of existing treatment by mechanical grinder and applying cement base wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats Distempering, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of ceiling applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats of Distempering approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and directed.

M&L for preparation of old decorated surface (plastered or unplastered) of ceiling by complete removal of existing treatment by mechanical grinder and applying cement base wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats Distempering of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and directed.

S&F WPC fluted Panel minimum 12mm thick consist of 40% PVC which is further hot stamped to give aesthetic and designer look Characteristics: Attractive, Strong, Waterproof, Termite Proof, Energy Efficient, Ready Easy to install Durable, Low Maintenance, Multiple designs, Fire Resistant, Light reflective easy to clean and wash, Safe and environmentally healthy etc and customised designs as per site requirement and directed by GE including connecting/perimeter bedding fixing on wall/ceiling to proper anchoring PVC wall/ceiling panel also suitable for holding ceiling light/LED stip of any shape and size complete all as specified and directed. Note : Measurement shall be considered as plan area only. Make : Prominent, Rajshree, Ekra Decor, Metroc

S&F PVC Panel of 4mm thick consist of 40% PVC which is further hot stamped to give aesthetic and designer look Characteristics: Attractive, Strong, Waterproof, Termite Proof, Energy Efficient, Ready Easy to install Durable, Low Maintenance, Multiple designs, Fire Resistant, Light reflective easy to clean and wash, Safe and environmentally healthy etc and customised designs as per site requirement and directed by GE including connecting/perimeter bedding fixing on wall/ceiling to proper anchoring PVC wall/ceiling panel also suitable for holding ceiling light/LED stip of any shape and size complete all as specified and directed. Note : Measurement shall be considered as plan area only. Make : Prominent, Rajshree, Ekra Decor, Metroc

M&L for multi layer POP false ceiling in steps (in layers) as per drawing produced by Engr in charge and as dircted by GE at site with horizontal and vertical GI frame work and fiber/mess reinforcement as required including POP work for finishing smooth. Painting with plastic plastic emulsion paint in two coats over primer over fininshed POP surface with suitable arrangement for Spot light/ceiling light as per drawing produced by Engr in charge complete all as specified and directed. Note : plan area shall be considered for measurement and payment purpose only.

S&F 18-20mm thick CNC Cut WPC jali with WPC frame of size 70x40mm with two coat of glossy deco paint to include all layers leading to deco paint for Plumbing Duct Cover, Shaft Cover, For Exterior use to provide solutions for exterior facade and elevational treatment for the building with waterproof, rusting proof with pigmented nature helps the color, unbreakabe including all fiting and fixing arrangement. The design and shape shall be porvided as per approved by Engineer in Charge and fixed with frame at concrete/brick structure complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of reinforcement to facilitate demolition (Parapet wall) complete all as specified and directed by Engr in charge.

M&L for 18-20mm thick granite as approved by GE mm thick (table rubbed and polished) in floors and like including 20mm thick screed bed in CM 1:6 and pointing in white cement (1:2) using marble dust with admixture of pigment to match the surface complete all as specified and directed.

M&L for Granite (of any type) work 18-20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, lift wall, skirting for design between udipur green mable wherever required and like in cement mortar (1:4), 15mm thick including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounded edges with shade of granite complete all as specified and directed by Engr in charge. Note : Minimum rate of granite should not be less than Rs 150 per Sqft including GST

Demolition of brick work or stone/boulder masonry including all quoins, arches, pillars, etc, built in cement mortar complete all as specified and directed.

M&L for Brick work with sub class "B" bricks , straight or curved on plan exc 6 m mean radius built in cement mortar (1:6),(up to two story Bldg) complete all as specified and directed.

M&L for Brick work with sub class "B" bricks , straight or curved on in half brick thick wall built in cement mortar (1:4),(up to two story bldgs.) complete all as specified and directed.

S&F in repair Vitreous China rimless wash down water closet pan single piece symphonic action, white, including soft close sheet cover of closed pattern with flat bottom complete all as specified and directed. Make: Hindware Cat part No 92573, Jaquar Cat Part No WC OPS-WHT-15853S300UF, Kohlar Cat Part No ‎77739T-SL-0

S&F in repair ABS body Health Faucet including flexible pipe of 15 mm bore and min 1.00M long with and including 15 mm bore complete all as specified and directed. Make- Jaquar Cat Part No ALD-CHR-573, Hindware cat Part No F160192CP, KOHLER Cat Part No 12927IN-CP, CERA Cat Part No F8030107AB

S&F in repair brass chromium plated toilet paper holder, complete all as specified and directed. Make: Jaquar Cat Part No ACN-1151N, Kohler Cat Part No 5633IN, or Hindware cat Part No F880003CP, CERA Cat Part No F5002110

S&F wall mounted bath room vanity unit of overall size 600x450x450 (approx) with multiple cabins with outside openable two shutter made of water proof coating/items/with two nos of 100mm stainless steel handle with hinges and auto closing and 16-18mm thick black polish granite with including counter type Table Top white ceramic basin of approx Size: 50x40 cm table mounted type including cuplink with stainless steel bottle trap of 32mm size with 250mm long complete all as specified and directed (Make of basin: Jaquar Cat Part No JDS-WST-25911 or Hindware cat Part No 91094, CERA Cat Part No S2020153 or Kohler Cat Part No K-31459IN-0), bottle trap and all fittings to proper functional condition complete all as specified and directed by Engr in charge. Make : Bottle trap and venity Make Jaquar, Kohler, CERA, Hindware or as approved by GE Note : Makes with cat part No of only WHB is given

S&F Single Lever Basin Mixer Wall Mounted Consisting of Operating Lever, including Exposed and Concealed Part (diverter) Cartridge Sleeve, Wall Flange, Nipple & Spout suitable for basin including all fittings complete all as specified and directed. Make: Jaquar cat part no OPP-CHR-15233NKPMM & ALD-235N, Kohler Cat Part No K-22540IN-4ND-CP, Hindware Cat Part No F570029CP, CERA Cat Part No F1023474 and F4065103

Taking up or down steel tubing and connections of 15mm bore and removal from site complete all as specified and directed.

Taking up or down steel tubing and connections of 20mm bore and removal from site complete all as specified and directed.

M&L for Cutting chases in brick wall pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for conc ealed water tubing or concealed conduit wiring, etc., and making good, cutting notexc 10 cm girth complete all as specified and directed.

Supplying and laying of CPVC 20mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl brass coupling fittings with fitting as required complete all as specified and directed.

Supplying and laying of CPVC 25 mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors incl brass coupling fittings with fitting as required complete all as specified and directed.

S&F in repair 1000 ltr capacity rotational moulded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) white colour hoisted and fixed in position complete all as specified and directed.

S&F in repair Bib tab (spout) 15mm bore while with Wall Flange complete all as specified and directed. Make: Jagaur Cat Part No OPP-15037PM, Hindware Cat Part No F340004C or KOHLER Cat PartNo : 16093IN-4-CP

S&F in repair Angular Stop Cock 15mm bore with Wall Flange while complete all as specified and directed. Make : Jaquar Cat Part No OPP-15053PM, Hindware Cat Part No F570043CP or KOHLER Cat Part No K-16094IN-4-BV

S&F Kitchen sink mixer 15mm dia CP brass fancy type including joints to steel pipe or unions complete all as specified and directed. Make Jaquar Cat Part No ARI39309, Kohler Cat Part No 20591 IN-CP, KOHLER Cat Part No K-37316IN-4-CP

S&F SS Grate 304 handmade single bowel sink with drainage board for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall / stone slab with connecting cuplink ,/union with waste pvc pine complete all as specified and directed. Make : Cera cat Part No B4712502, Hindware Cat Part No Marino 40"x20"x9", GLEN Cat Part No KS-SH36209SBSDM

S&F in repair 5mm thick modern mirror of size 450x600mm fixed on decorative PVC cabinet with border design suitable for wash basin cabinet with fitted with LED Front and Backlight, Stepless Dimmable Wall Mirrors with Anti-Fog, Shatter-Proof, Memory, 3 Colors, Double LED Vanity Mirror with touch off/on switch in one mirror including all fixing arrangement complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description and any positions not other wise provided for complete all as specified and directed.

M&L for steel work as in hand rails, wind ties for roof including securing bolts, posts and struts in fencing including cutting top to shape as directed drilling holes, notching for wire etc flat iron fillets for securing wire mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 Gde E-165 complete all as specified and directed.

S&F structural mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framingetc (beam, tee, angle, channel or flat section) including distance pieces, cleats etc confirming to Fe 410-W (Gde 250 quality A) complete all as specified and directed.

S&F round shape colour or transparent (as directed by engr in charge) Polycarbonate Sheets ‘H’ pattern multiwall of 10mm thick and wall 1 mm nominal thickness, excellent physical properties of polycarbonate, UV surface protection, min 20 % light transmission,high impact resistance, weather resistant, High heat and sound insulation, Long life span, Temperature resistant- between -20°C +100°C, light-weight, superb thermal suitable for Roofing, Shedding, walling etc fixing with MS frame structure with self tapping stainless steel screw with rubber/polycarbonate washer and all joints shall be filled with silicone jel all as specified by manufacture complete all as specified and directed. Note : shape shall be rounded/oval and no extra cost shall be considered and all inclusive in the quoted rate

S&F aluminum strip for polycarbonate sheet pressure and closures of size 40mm wide section on roof/wall as it forms a weatherproof seal to the end of the sheets preventing water ingress and aids in maximum lifespan of the polycarbonate sheets alongwith rubber bids in groves of aluminum strips with self-tapping stainless steel screw with rubber/polycarbonate washer as per manufactures instructions complete all as specified and directed by Engr in charge.

Taking down chowkats or frames with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4.00 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

S&F Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, where required one window AC duct will be provided as per direction at site complete all as specified and directed by Engineer-in-Charge. Note: The unit rate quoted by contractor include cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose

S&F in repair of 25mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . /25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite) Plain Board incl facias will have 2mm thick uPVC edgebands in color matching with the external laminate of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen & Cabinets complete all as specified and directed. Make : Floresta, Alstone, Ecoste, CenturyPly, SV Woods, Giza

S&F High Gloss Finish Liner Laminate /High-Pressure Laminate (HPL) Sunmica of 1.0 mm thick of multi colour/design as approved by GE to be fixed to wpc/wood/plywood surface with preparation of new surface and apply best adhesive for pasting as per manufacture instruction complete all as specified and directed.

S&F hydraulic silent soft closing tandom drawer system concealed full extension single gallery 150mm length 500mm, width adjustable and load capacity should not be less 45 Kgs fixed with screws in cupboard incl all fittings complete all as specified and directed by Engr-in-charge. Make- Hettich, Hafele & Kalf.

S&F hydraulic silent soft closing tandom drawer system concealed full extension double gallery 200mm length 500mm, width adjustable and load capacity should not be less 45 Kgs fixed with screws in cupboard incl all fittings complete all as specified and directed by Engr-in-charge. Make: Hettich, Hafele & Kalf

S&F Modular Cabinet Kitchen accessories of PVC heavy cutlery tray 600mm wide for tandom drawers complete all as specified and directed by Engr-in-Charge.

S&F Modular Cabinet Kitchen accessories of PVC heavy cup and saucer tray 600mm wide for tandom drawers complete all as specified and directed by Engr-in-Charge.

S&F Modular Cabinet Kitchen accessories of PVC heavy bottle tray 200mm wide for tandom drawers complete all as specified and directed by Engr-in-Charge.

S&F MS roller with "C" shape staple, chromium plated for 5.5mm thick sheet glass complete all as specified and directed.

S&F 75 mm long L Bihari concealed type auto closing hinges incl stainless screw, complete all as specified and directed.

Expose the first joint of masonry structure at ground level horizontally. The plaster must be knocked off at least 50 cm beyond the visibly penetrated area. Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. Drilling Holes : Drilling holes 10mm diameter in masonary structure along the side of the joint as per manufacturer's instructions so as to cross the brick/ block at the intervals spacing of 15-30cm depending on extent of rising dampness as per recommendation of engineer in charge. Cleaning of holes : Clean the holes by air blower prior to fixing nozzles. Install latex polymer packer injection packers 9.8mm diameter, 10cm long in the holes and tighten. Fix the packer securely using sealant. Cutting of Packers : Cut the packers after completion of grouting without damaging structural elements.

Supply and applying of a 3 part, very low viscous, elastic polyacrylic injection resin with a versatile and adjustable reaction time having Mixed viscosity : 3-11 M.pa.s at +20 Deg C, Reaction time : adjustable according to ambient temperatrure and execution requirement between 8-50 mins, pH – 9-10, tested as per Wissbau No. 2002-094-(1A) – Function test with re-injectible hose system. The holes should be drilled until a depth of approx 5 cm (for a 6cm thick wall) before the end of the wall is reached. Pump injection of polymer resin compound at >20 bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas. If voids in masonry being injected contain insufficient moisture to activate the grout inject a small amount of water prior to injecting the grout. When movement stops or polymer compound appears at the packer move to the next packer and inject. If the dampness is heavy, inject similarly at next joint line complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m deep for foundation and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25 cm soft/ loose soil complete all as specified and directed by Engr in charge.

Removing excavated materials n exc 50 m and depositing where directed at a level n exc 1.50 mtr above the starting point complete all as specified and directed.

Demolition and breaking up drain pipes salt glazed stone ware pipes 150 mm dia (internal) set in cement mortar complete all as specified and directed by Engr in charge.

M&L for HDPE Black DWC Sewerage and Drainage Pipe 150 mm in trenches and jointed with using rubber gasket and pipe joint lubricant for both end and 150 to 200 mm wide color joint socket shall be provided to cover the joint all around as per specification and manufacture instruction including PCC bed complete all as specified and directed.

M&L for HDPE Black DWC Sewerage and Drainage Pipe 300 mm in trenches and jointed with using rubber gasket and pipe joint lubricant for both end and 300 to 350 mm wide color joint socket shall be provided to cover the joint all around as per specification and manufacture instruction including PCC bed complete all as specified and directed.

M&L for trenchless excavation my mechanical process without disturbing road/top surface for taking out any type of soil/rock of any sizes to laying 150mm to 300mm bore sewage/drain pipe upto depth of 3.0 mtr complete all as specified and directed. Note : (a) Cost of transportation of trenching machine included in this rate (b) Cost of returning & refilling and removal of extra soil deemed to be included in this rate and nothing extra paid on this account.

Providing and laying 60mm thick factory made chamfered edge cement concrete PU coating and glossy finished paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand including demolition/dismanlting complete all as specified and directed.

S&F in repair PVC (SWR) pipes single socketed, 110 mm bore pipe in any length with rubber ring joints, fixed to walls/floors, complete all as specified and directed.

S&F in repair PVC (SWR) bends/Tees, Y, trap any type, brachpie, cowls or like imilar of radius of 110 mm bore, complete all as specified and directed by Engr in charge.

S&F PVC (SWR) pipes single socketed, 75 mm bore pipe in any length with rubber ring joints, fixed to walls/floors, complete all as specified and directed by Engr in charge.

S&F PVC (SWR) bends/Tees, Y, trap any type, brachpie, cowls or like imilar of radius of 75 mm bore, complete all as specified and directed by Engr in charge.

S&F Aluminum section for door,window, partition and similar frame work or shutter, corner 45 degree cut & aluminum welded & mechanically joint alenkey bolt clamp, 12mm design/forsted/ with balck flim glass with both side EPDM rubber gasket, nylon double bearing, full system powder coating with pure polyester coat of any shade install with SS screw rowel plug PVC & silicone complete all as specified and directed. Note: Glass Panes will be measured and paid separately

S&F 12 mm thick sheet glass ordinary quality with flim and glazing to fix at aluminium frame structure complete all as specified and directed.

M&L for concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in floor and sub base including use and waste of form work where reqd complete all as specified and directed.

M&L for concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in path, hardstanding laid in panels with and including use and waste of form work and to divide the area in panels and finishing the surface fair and even complete all as specified and directed.

S&F door closer Floor Machine aluminium body and Stainless Steel floor cover for Floor Spring Heavy Duty Door Spring/Commercial Door Closer of min 120Kg weight load capacity complete all as specified and directed.

S&F 12mm thick toughened desing/frosted glass as approved with SS 30x10x 1.8mm thick matalic frame track for partition including one top hang sliding door with all fittings such as guide, runner, handle, roller, hinge, stopper, braket etc and fixing with SS screw etc and all joints shall be filled with silicon/appoxy as per direction complete all as specified and directed by Engr in charge.

S&F Stainless Steel D Type Glass Door Handle, Pipe Pull Handle for Glass Door Handle of 200mm with fittings of grage 304 complete all as specified and directed.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engr in charge.

M&L for providing and fixing stainless steel (Grade 304) link chain of 5mm dia min 30mm each link including welding, grinding, buffing, polishing and fix to SS pole complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels, drains including all necessary form work complete all as specified and directed.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in coping including weathering, slightly rounded or chamfered angles and throating, as directed and necessary form work complete all as specified and directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed. Note : For adjustment of rate only against item No 92.00 here-in-before

E&M PORTION: Taking down carefully old point wiring with aluminium/ copper conductor (Light / Fan/ Socket/ power Point ) complete including fittings such as ceiling rose, pendent holders, regulators and socket point etc and making good the disturbed surface & wall/ floor complete all as specified and directed by Engr in charge.

M&L for point wiring with PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 Sqmm 1100 V grade including one run of PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 sqmm as earth continuity conductor connected to common earth dolly in and including PVC concealed conduit 20 mm dia medium grade ISI marked and its accessories including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size for housing the modular switches, sockets, fan regulators for one light/ fan/ exhaust fan point controlled by one no, one way 5 Amp switch complete all as specified and directed. Note: (i) Cutting chases for concealed conduit and making good in cement mortar is deemed included in unit rate. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling point wiring. In this specified portion wire shall run through the existing conduit or surface new conduit shall be provided as required. (iii) In case the wiring is encountered with any beam/column, then the wiring will run on surface to avoid any damage to the RCC portion.

All as per item No 92.00 above but for One bell/buzzer point controlled by one bell push complete all as specified and directed.

All as per item No 92.00 above but for One 3 pin 5 Amp socket outlet on the same board complete all as specified and directed.

All as per item No 92.00 above but for One three pin 5 Amp socket outlet point controlled by one no, one way switch on independent board complete all as specified and directed.

All as per item No 92.00 above but with 2 x 2.5 Sqmm +1 x 2.5sqmm Copper conductor cable for one 3 pin, 15 Amps Switch socket out let on independent board complete all as specified and directed.

S&F in repair modular Switch 6 amps, 230 vots, single pole, one way (ISI marked) with IP 20 rating complete all as specified and directed. Make : Havells Cat part No-ACNSXX101, Legrand Cat Part No-573400, Indoasian Cat part No-810600

S&F in repair modular bell push 6 amps, 230 vots, single pole, one way (ISI marked) with IP 20 rating complete all as specified and directed. Make : Havells (Murano) Cat Part No ACUSBXW101, Legrand Cat Part No 673404 , Schneider Cat Part No X1005WH

S&F in repair 16 Amp rating modular switch one way one module with IP 20 rating complete all as specified and directed. Make : Havells Cat part No-ACNSXX161, Legrand Cat Part No-573410, Indoasian Cat part No-810601

S&F in repair modular socket out let 230 volts grade (as catered in point wiring above) 6 Amp - 2/3 pin combined 2 module complete all as specified and directed by Engr in charge. Make : Havells Cat part No-ACAKPXW063, Legrand Cat Part No-573470, Indoasian Cat part No-810620

S&F in repair modular socket out let 230 volts grade (as catered in point wiring above) 16 Amp - 2/3 pin combined 2 module complete all as specified and directed by Engr in charge. Make : Havells Cat part No-ACAKPXW163, Legrand Cat Part No-573471, Indoasian Cat part No-810621

S&F in repair electric bell AC 230 Volt ding-dong type complete all as specified and directed by Engr - in - Charge. Make: Havells Cat Part No AHNLEXU002, Legrand Cat Part No 573443, Schenider Cat Part No HSN-853650

S&F in repair Modular MCB SP 16 Amps 240V 3 KA, C Curve, fitted in main switch board, including 2.5 sqmm wire connecting power socket & modular MCB complete all as specified and directed by Engr-In-Charge. Make: Havells Cat Part No DHFNCSPA016 or equivalent in legrand/ schneider.

S&F in repair facctory made SPN DB's double door made out of CRCA mild steel sheet with insulating materials like polyester epoxy coated surface mounting 8 way SPN 220 Volts, with suitable busbar, neutral link & earth link suitable for complete all as specified and directed. Make : Legrand Cat Part No 507611, L&T Cat Part No PH108DD8 /Schneider Cat Part No NBKRESNDD08

S&F in replacment MCBs, SP 6 to 32 Amp type B or type C as per site reqmt, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule) complete all as specified and directed. Note: Make of the MCB should be the same as that of DB

All as per item No 105.00 above but MCB SPN 40 tp 63 Amps Type B OR Type C as per site requirement complete all as specified and directed.

S&F in repair round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-charge. Make: Philips, Orient, Havells, Crompton, Bajaj, Jaquar

S&F in repair LED Tube light of 20 watt 230 volt (approx size 4ft box type complete with LED tube light 20 watt & all accessories internally prewired including connecting up with three core sheathed flexible copper conductor cable of suitable size having min P.F>0.95, minimum efficacy 120 lumen/watt IP 20 rating complete all as specified and directed. Make: Bajaj cat Part No BAJAJ BLAB 20W CW LED XT, Crompton cat part No CCS-100-20-65-HL2-OP-NWH, Philips cat part No BN308C LED20S-6500 L120 PSU WH

S&F in repair round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three flexible copper cable size complete all as specified and directed. Make: Philips, Orient, Havells, Crompton,Bajaj, Jaquar

S&F in replacement of aesthetically designed muziris decorative warm white LED picture light 8 watt, PF > 0.95, min efficiency 100 lumen/watt, IP20 rating CCT 3000K fixture with bronze finish for superior feel complete all as specified and directed. Make: Philips/Bajaj/Crompton

S&F 10 watt LED garden BollarD LIGHT .The garden bollard is made out of cast and extruded aluminium .The dimensions of the garden bollard are 100 mm width and 750 mm height .A transparent toughened glass protector is fitted in the luminaire .a COB based led shall be fitted in the suitable heat sink for proper heat dissipation .suiatble constant current led driver with power factor 0.95 or more and efficiency 85% or more shall also be fitted inside the luminaire .A two way connector shall be provided in the luminaire for the mains connections .bollard shall be installed at desired location including foundation of the same by making cement conrete fondation of 1;2;3 (1cement : 3 course sand : 6 graded stone aggregate 40 mm nominal size) with the help of Anchor bolts and GI sleve as required complete all as specified and directed. .Make : philips,Orient,crompton

S&F in repair LEO luminaire 600mm x 600mm, 35/36 watt. 220 V, PF>0.95. AC recessed type with high efficiency, MMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed. Make Havells Cat Part no VENUSNE02X2PLR36WLED865PO, Philips Cat Part No RC370B LED36S-6500 G6L60W60 PSU OD S6, Crompton Cat Part no LCTRP-36-FO-CDL.

S&F PVC body exhaust fan 250mm sweep, 230 Volt AC 50 Hzincluding louvers. The rate includes making proper arrangement for fixing i.e. cutting bricks/stone boulders of appropriate size and finishing the surface with cement work and matching paint finish complete all as specified and directed Make:-Usha style name modern Crisp Air V/Bajaj maxima 250/Havells Venti air DX

S&F BLDC ceiling fan 1200 mm sweep, with remote 230 volts having full copper motor & ribbed alluminium blades for higher air delivery, powder coating provides longer life complete with accessories including making arragement to hanging of fan to ceiling with proper hook nut bolts complete all as specified and directed. Make: Havells Cat Part No Ambrose slim star 1200, crompton Cat Par No Energion Cromair, Bajaj Cat Part No Bajaj Ethora Plus.

S&F in replacement for submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x6 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x 6 sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire and duly connected to common earth dolly complete all as specified and directed. Make- Polycab, Havells, RR KABEL

S&F wall mounted electric chimney of minimum width 60cm, having suction power not less than 1350cum/Hr. with stainless steel outer layer, with 3 speed motor with decorative smart cooker hood SS/glass, energy efficient LED light with digital display including ducting,having auto clean function, noise level not more than 60dB, Control Panel-Touch & motion sensor control, including ducting as per site requirement complete all as specified and directed by Engineer in Charge. Note- The rate quoted by the contractor will include ducting length required from the chimney to the exhaust hole. Make: HINDWARE COOKER HOOD CELESIA 60 BLK, FABER- COOKER HOOD MAGNUS 60, Elica- WD TBF HAC 60 MS

S&F one module RJ -11 telephone socket completet all as specified and directed

M&L in replacement plate earthing complete with galvanized mild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than 2.25 meter deep below ground level) with the top edge of earth plate at a depth not less than 1.5 meter below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and including GI strip 32x6 mm bolted (with GI nuts, bolts & check nuts) and riveted to earth (Plate) electrode at one end and connected to main switch board test point at the other and watering GI pipe (medium grade) 20 mm bore from bottom of earth pit to top of electrode and 40 mm GI pipe light grade for earth strip protection complete with earth pit in PCC 1:2:4 type B0 using 12 mm graded crushed stone aggregate, RCC cover etc complete all as specified and directed by Engr in charge.

S&F in replacement of factory made TPN DB's double door made out of CRCA mild steel sheet with insulating materials like polyester epoxy coated surface mounting 8 way TPN 415 Volts, IP 43 with suitable busbar, neutral link & earth link suitable for MCCB TPN as incomer & MCB SP/SPN as out going complete all as specified and directed. Make: Havells/ Schneider/ Legrand

S&F 100 amp 415V 10KA 'B' curve miniature circuit breaker (MCB) of four poles and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed. Note: MCB shall be the same make as of DB

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 6 sq. mm 3 core complete all as specified and directed. Note : laying and covering of cable under soft soil by included in the quoted rate , cable must be layed in a PVC conduit of suitable size Make: Polycab/ Havells/ KEI/ RR Kabel

S&F GI cable tray made from 1.5 mm thick pregalvanized sheet for top, bottom & sides and complete with top cover with rubber gasket of size 300*38 mm complete for mounting and supporting the cable tray system, along with vertical bends, bends, including taking down and re fixing any type of electric cable, LAN /signal cable, if require through wall/floor cutting and making good surface of disturbed area all complete all as specified and directed. Note : nut bolts bracket and other accessories required must be included in the quoted rate

S&F Exhaust fan AC single phase 230/240 v of size 300mm sweep sweep rpm metal body, Air delivery 1850 cum/hr, high efficiency motor, dynamically balanced blade for better performance and corrosion-resistant powder coated metallic finish including hole making Louver complete all as specified and directed by Engineer-in-Charge. Make:- Havells- Ventilair DB ,Crompton, Orient, Bajaj- MAXX AIR

S&F in replacement of ceiling rose surface bakelite surface 65 x 50mm 3 terminals complete all as specified and directed. Note: (a) Srl Item No 04.00, 11.00, 19.00 to 22.00, 24.00, 27.00, 38.00, 46.00 to 48.00, 52.00, 55.00, 70.00, 71.00, 78.00, 80.00, 85.00, 92.00, 104.00, 107.00, 109.00, 111.00, 112.00 & 115.00 of BOQ and bathroom fittings and sanitary fittings are major items for the subject tender and material in respect of these items shall be procured within one month after placing of work order and produced before Engg in Charge alongwith original purchase vouchers as per direction of Garrison Engineer and shall obtain a certificate from Engg in charge that material in respect of above mentioned items have been submitted in the office of Engg in charge in their safe custody. (b) Materials in respect of Freakishly low declared items if any at the time of acceptance of contract shall be procured within one month after placing of work order and submit the same in the office of Engg in charge alongwith original purchase vouchers in their safe custody and shall obtain a certificate from Engg in charge.

YASH ENGINEERING (BID ID -3516895)

Ex Serviceman Enterprises (BID ID -3523301)

BEHAL TRADERS (BID ID -3523310)