PROVISION OF FEMALE PATIENT ISOLATION ROOM AT MH AND SPECIAL REPAIR TO BLDG No P- 160 OF PVKC (04 ROOMS) AT SAW, ACC AND S UNDER GE (N) AHMEDNAGAR

Amount

Taking down cement plaster on brick or concrete surfaces on wall/ceilling/stone/block etc including racking out joint, hacking for key,scrubbing down with water etc all as specified and as directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard / dense soil.

Excavation over areas not exceeding 1.5 M deep and getting out in soft / loose Soil

M& L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat rough finished complete all as specified and directed .

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide .

M&L for Flat form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exce 200 mm thick.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc

M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges

M&L for Reinforced Cement Concrete Design Mix Type M-25 (using 20 mm graded granite stone aggregate) in Chajjas

M&L for special treatment ot sunken portion with 10mm thick plaster in CM 1:4 with WPC liquid complast 421 and applying one coat Each of Nittoproof 120 on plastered surface rendering again 10mm thick in CM 1:4 mixed with complast - 421 filling the sunken floor with PCC 1:5:10 using brick bat area of floor upto 1.5 Sqm including 40 mm dia 0.60 m pipe etc complete all as specified and directed by Engineer-in-Charge. Note : Work has to be carried out strictly by the authonticated applicator of the manufacturer and as per manufacturers specification as approved by GE.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 , finished even and smooth without using extra cement with WPC.Note:- WPC shall be measured & paid seperately.

M&L for rendering 15 mm thick in CM 1:6 over brick surfaces, finished even and smooth without using extra cement all as specified and as directed.

M&L for rendering 5 mm thick in CM 1:3 on ceillng, finished even and smooth all as specified and as directed.

M&L for applying two coats of OBD over a coat of primer Chalk whiting, on plastered surfaces, prepara-tory to distempering on newly plastered wall surfaces all as specified and as directed.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash.

M&L for preparing the newly plastered or unplastered surfaces and applying one coat of alkali resistance priming paint over two coats of cement based paint .

M&L for preparing new plastered surfaces and applying Two coats of cement base paint over a coat of alkali resistant primer on surfaces of walls.

Supply only integral water proofing compound

M&L for preparing old surfaces of ceilings by brooming down or by steel wire brushing and applying one coat of white wash including scafolding at any height complete all as specified and directed by Enggineer-in-charge.

M&L for preparing old painted surfaces by washing, rubbing down and stopping of distempered and painted surfaces and applying a coat of distemper oil emulsion on surfaces of walls including scafolding at any height complete all as specified and directed by Enggineer-in-charge.

Preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint including scafolding at any height complete all as specified and directed by Enggineer-in-charge..

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) including scafolding at any height complete all as specified and directed by Enggineer-in-charge..

M&L for complete removal of existing treatment and prepartion of surfaces on surfaces of walls and applying two coat of acrylic distemper Chalk whiting, on plastered surfaces, prepara-tory to distempering including scafolding at any height complete all as specified and directed by Enggineer-in-charge.

M&L for 3mm thick wall care putty on wall

M&L for preparing old painted surfaces by washing, rubbing down and stopping of painted surfaces and applying a coat of cement base paint on surfaces of walls including scafolding at any height complete all as specified and directed by Enggineer-in-charge.

M&L for repair to crack including cutting V groove along cracks removing all dust and loosely laid particles using a blower wetting the crack using water and filling the crack using crack seal compound paste as per manufactures instructions and finishing using putty blade complete all as specified and directed at any height incuding necessary scaffolding. Make : Fosroc renderoc CS/ Sika cracksil/ Pidilite Dr fixit 217 Crack x Shrinkfree.

M&L for applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 0.715litre/ 10 sqm complete all as specified and directed at any height incuding necessary scaffolding over existing surface.

Demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including floor finishes

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

S&F light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:6 .

S&F light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10 mm thick in CM 1:4 on fair faces of brick or concrete surfaces of wall as in backing of skirting and dado all as specified and as directed.

S&F coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:6

M&L for Glazed ceramic coloured in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including rendering 10 mm thick in CM 1:4 on fair faces of brick or concrete surfaces of wall as in backing of skirting and dado all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors aprons etc.

M&L for machine cut cudappah stone 18-20 mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed for vertical support.

M&L Rounding to edges of stone slabs one edge ,such as in steps cooking platform and other similar situations

M&L 20mm thick granite (of any type ) work (table rubbed and polished ) in steps, jambs, pillars, window -cills, cooking platforms and like in cement (1:4) including pointing in wihte cement (1:2) using marble dust with admixture of pigment ot match with shade of granite.

M&L for 75 mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base all as directed.

Taking down of chowkat with shutter without taking off shutters from the frame exceeding 1.5sqm each but not exceeding 4 sqm all as specified and as directed.

Taking down of chowkat with shutter without taking off shutters from the frame, not exceeding 1.5sqm each all as specified and as directed.

Taking down of shutters of any description exceeding 1 sqm each and not exceeding 2 sqm each all as specified and as directed.

M&L for re-fixining same opening of shutters of any description exceeding 1 sqm each and not exceeding 2 sqm each all as specified and as directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board coare supplying & fixing in frame at site as per specification & drawing on sl. page no. 161 of SSR part II 2010

S&F aluminium framed windows any pattern, fixed/side hung/silding ( three track) using powder coated of thickness 50 micron alluminium sections, of approved make with or with out sash bars suitable for 4.80mm thick glazing including necessary jointed cleats, glazing all as specified Note-: (glazing shall be measured and paid separatly)

S&F 30mm thick flush door shutter soild core construction with block board core and plywood face panels commercial type on both sides .

S&F second class hardwood glazed and skeleton shutters 35mm thick open rebated and prepared to receive glass gauge etc with sash bar divided into squares edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass or gauze etc sizes of members of shutters as specified inSSR part-I section 8 clause 8.20 (a) fitted to chowkats .

Hacking out old broken glasses any thickness, size, quality or description from metal frame including punching out or drilling out old glazing pins/spring clips and providing and fixing new all as specified and as directed.

S&F sheet glass ordinary quality 3 mm thick with oil putty not exceeding 0.5 sqm in each pane all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples all as specified and as directed.

Ditto all as per item No 51 above but fixed in repair to steel/wooden shutters

S&F in repair butt hinge, stainless steel 100mm long all as specified and as directed.

S&F in repair butt hinges stainless steel 75mm long all as specified and as directed.

S&F aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy 300 mm long and fixed all as specified and as directed.

S&F Floor door stopper of aluminium alloy body double and tongue anodised with rubber shoe and fixed of size 150 mm all as specified and as directed.

S&F aluminium anodised barred tower bolt of extruded section 200 mm long and fixed all as specified and as directed.

S&F extruded aluminium alloy handle fabricated type anodised 150 mm long

Ditto all as per item No 58 above but 100mm long

M&L for mild steel frame work such as grills with ends of bar shouldered, welded or forged into spikes conforming to Fe 410-0 or Fe 310-0 and taking down old one .

M&L for preparing new surfaces of wood of any description over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed.

Ditto all as per Sr item No 61 above but on steel surfaces over red oxide primer

S&F 300 mm long, mild steel ordinary rat rail springs including roller and roller plate complete and taking down old one all as specified and as directed.

S & F 20 mm dia of Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. brackets etc all as directed in repairs.

S&F in repair aluminium extruded Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

S&F IInd class hard wood plain solid, straight ,chowkats and frame, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints all as specified and as directed.

S&F hasp and staple, safety type aluminium anodised with hinge pin including bolt to hinge plate and fixed with screw 125 mm long all as specified and as directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges shall be paid separately) incl taking down old one

S&F Pressed steel frames for doors with one or more rebates of size 125 x 60mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as pecified, supplied and fixed

S & F in repair vitreous china wash basin, white back, size 500 X 400 mm x 190 mm , errecting on existing CI brackets including taking down old one alll as specified and as directed . Note: If the mentioned size is not available in the market , the next immediate higher size shall be provided by the contractor .

S & F Vitreous Ware wash down water closet (Pedestal), white (ETWC) and fixed in repairs including seat cover with brass screws and excluding flush pipe and flushing cystren

S&F 10 in repair litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and taking down old one complete all as specified and as directed

S&F in repair PVC water closet seat and cover, black or white, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device including taking down old one all as specified and as directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long.

S & F in repair Soap dish, vitreous China white of approximate size 160 x 160 x 90 mm.

S&F PVC mirror cabinet of size350x450mm of make PRAYAG PODUCT CODE NO551 or equicalent on COMMANDER including taking down old inbuilt cabinet all asspecified and as directed.

S&F Towel Ring of PTMT and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms).

S&F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms).

S&F Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S & F in repairs 40 mm dia., Waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

Taking up or down steel tubing 15mm dia and connections, including cleaning for re- fixing

Taking up or down steel tubing 20mm dia and connections, including cleaning for re- fixing

S&F 16 mm dia Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F 20 mm dia Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Dismantling existing PVC water tanks of capacity exc 250 litres & n.exc 500 litres all as directed and removed from site. NOTE:-Dismantled water tank shall become the contractors property as per Sch of credit.

S&F 1000 litres rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed .

S and F Ball brass valve 20 mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule

S & F in repairs Fancy type chromium plated with long shank and cup (Concealed type) 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S & F in repairs Fancy type chromium plated with long shank and cup (Concealed type) 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F 15mm dia Chromium plated fancy type Bib taps cast copper alloy with crutch or butterfly handles screwed down screwed for iron pipe fixed in repair all as spd & directed .

S&F in repair Brass chromium Brass CP wall mixer 3 in 1 system with provision of hand shower/overhead shower for mixing hot & cold water screwed down for iron pipe and fixed as all specifed and as directed.

S&F waste coupling of PTMT 40mm (half or full threaded) sutable for kitchen sink. (Minimum weight 32mm- 45gms/40mm-60 gms)

S&F in repair Brass chromium plated bottle traps of 32/40 mm dia for wash asins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed

S&F grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms)

S&F in repair Chromium plated shower roses 125 mm dia size with or without swevel joints and size including fixing to steel pipe or union.

S&F PVC connections 15mm size with PTMT nuts of length 450mm

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls.

S & F 110 mm bore PVC (SWR) bends of any radius.

S & F 110 mm bore PVC (SWR) bends of any radius with access door.

S & F 110 mm bore PVC (SWR) branch piece single (Single `Y') equal or unequal with access door.

S&F PVC (SWR) pipes single socketed, 75mm dia in any length with rubber ring joints, laid in trenches or in floors

S&F PVC (SWR) bends any radius 75mm bore

S&F PVC (SWR) multi floor trap 75mm dia with grating including jointing with solvent cement

S&F in kitchen or laboratory sink with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

Taking down carefully existing unserviceable bitumen felt(any number of layers) including plaster of any thickness, wire brushing and cleaning of the surface of roof terraces including flashing and junctions of parapets kerb wall, PCC fillets, benching etc and removing of the rubbish to a distance not exceeding 500 m from the building and depositing where complete all as specified and directed

M&L for rendering 10 mm thick in CM (1:4) on roof slab top finished even and fair without using extra cement complete all as specified.

Demolition of plain cement concrete (unreinforced) in ground floor including concrete at junctions of parapets and roof terraces, flashing kerbs walls, PCC fillets, benching coving of chajjah top/junctions etc complete all as specified

M&L for providing plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) for roof, kerb, or mud stops, rounded or chamfered on edges etc complete all as specified and as directed.

M&L PCC 1:4:8 type D-2(40mm graded aggregate) in foundation , sub base, filling and mass concrete.

M&L for cleaning the newly plastered surfaces of concrete (roof etc) with wire brushes and applying water proofing treatment as under :- (i) Checking the roof slab by flooding test with water till total elimination of leakage/seepage/ dampness all as specified in SSR Part-I (after ascertaining location of leakage/seepage/ dampness, carrying out treatment vide item No. hereinafter of pressure grouting shall be operated at the required locations). (ii) Brushing surface with neat cement slurry at the rate of 3.00kg of cement per Sqm. (iii) Applying one coat of oil bound bituminous primer @ 0.25 kg/Sq. M (iv) Providing and laying 3mm thick APP modified water proofing membrane weighing not less than 3.5 Kg/Sqm reinforced with non woven polyester mat weighing not less than 160 gm/Sqm all as specified procured from any one of the approved manufactures (v) Apply two coat of solar reflective bituminous aluminium paint @ 0.15 kg/Sqm per coat over membrane over non assesble roof surfaces complete all as per manufactures instructions and as directed

M&L for preparing of concrte /plastered roof /Chajjas etc with and including comprising of the following steps:- (a) Checking the roof slab by flooding test with water till total elimination of leakage/seepage/ dampness all as specified in SSR Part-I (b) Cleaning & drying thoroughly existing surface of roofs,chajjas etc for all forign matters such as fungus,moss dust etc by wire brushing and dusting. (c) Removing loose concrete surfaces cracks etc and then apllying/filled with Dr fixit crack x or polymer modified mortar in case of wider cracks ( Bitumen based water proofing treatment must be removed by mechanical sacrification) or equvalent in SIKA/STP/BERGER/Thermex. (d) Applying one coat of Dr fixit roof seal top coat (diluted with water 2:1) at the rate of 100-110 Sqft/Ltr and then allow it to dry for 2-3 hrs or equivelent in SIKA/STP. (e) Applying two coats of Dr fixit roof seal top coat ( diluted with water 2:1) embded a glass fiber mest (2x2mm-40gms) between the first and second coat as reinforcement complete all as specified and directed. Make:- Dr Fixit roof seal or eqivelent in SIKA/STP/Bergar/Thermex as approved by GE. Note:- Work shall be carried out through authorised applicator of the approved product only & 05 years waranty will be submitted by manufacturer.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed .

M&L for Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed .

M&L for Mild steel TMT bars in stirrups, spacers and binders for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed .

M&L for RCC Design Mix Type M-25 using 20 mm graded granite stone aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed .

M&L for RCC Design Mix Type M-25 using 20 mm graded granite stone aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed .

M&L for RCC Design Mix Type M-25 using 20 mm graded granite stone aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed .

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed .

M&L for Brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:6 complete all as specified and directed .

M&L for readymix plaster 10mm thick on fair face of brick work or concrete surfaces finished even and smooth surfaces using without extra cement in internal surfaces.

M&L for readymix plaster 12 mm thick on other than fair faces of brick work or concrete surfaces finished even and smooth surfaces using without extra cement of external surface including water proofing compound.

M&L for readymix plaster 5mm thick on fair face of brick work or concrete surfaces finished even and smooth surfaces using without extra cement in ceiling.

M&L, Hardcore of broken stone of gauge n exc 63mm deposited, spreaded & levelled in layers n exc 15cm thick including watering and ramming etc complete.

Moorum filling in floors/pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed/ rolled including watering to required level and gradient.

S&F for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

S&F for Wall / Ceiling Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

S&F for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge.

S&F sheet glass ordinary quality 4.8 mm thick exceeding 0.5 sqm in each pane all as specified and as directed.

S/F for PVC gully trap 125 / 110 mm , setting and jointing with solvent cement

S & F 75 mm bore PVC (SWR) bends of any radius with access door.

S & F 75 mm bore PVC (SWR) Vent Cowl

S&F steel water tubes, `meedium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors of 15 mm bore.

S&F steel water tubes, `meedium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors of 20 mm bore.

S&F stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe 15mm (fancy type chromium plated).

S&F in 15 mm bore Fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed

S & F Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified including seat cover with brass screws and excluding flush pipe and flushing cystren

S&F brass chromium plated hand shower (Health foucet) with 1 meter long easy flex tube in chrome finish and wall hook with NRV (back flow preventer ) all as directed.

S&F for 25mm dia curtain rod stainless steel with end fitting not less than 75 gms each and fixed with steel screw in brackets to walls complete all as specified and directed.

M&L for Providing and laying 60mm thick factory made glossy finished chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand all as directed.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

S & F RCC Class NP 2, 150 mm bore pipes laid and jointed complete with collars.

M/L for PCC( 1:4:8) type D2 using 40 mm graded aggregate as in concrete bed to drain pipes 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified.

M/L for precast RCC 1:2:4 type B1 as in man holes cover slabs set in cement mortr 1:6

Cutting in to existing manholes for connecting new drains making good to pipe & rendering cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1: 2:4 type B1 smooth finished & reforming benching as required for 150 mm pipe.

M&L for PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in surface channels/drains , etc complete all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms,moulds, mitred/stopped end etc.

S&F for precast hume pipe septic tank of capacity 50 users incl necessary excavation and earthwork in any type of strata all as specified and directed by Engr-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft / loose soil.

M&L PCC 1:3:6 type C-2(40mm graded aggregate) in foundation , sub base, filling and mass concrete.

S & F Rolled Mild Steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to Fe 410 - W (Gde E-250)quality-A,

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified specified etc all as directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Removing excavated material of soil exc. 250 m but n exc. 500 m and depositing where directed

M&L 75 mm thick cement concrete type C-2, 1:3:6 (Using 40 mm graded aggregate) finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as spd and directed.

Taking down carefully copper/aluminum point wiring (light/fan/bell/socket, power point etc) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors etc complete all as specified and directed Engineer-in-Charge.

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories PVC boxes (upto 12 module suitble for Mylinc series of Legrand including white plates with frame upto 12 module of make suitable for Mylinc Series ) for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS cable as earth continuity conductor to common earth & connecting to earth dolly for the following, all as specified and directed. Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, ceiling lights, bulkhead lights, bldg security light etc

One light point controlled by switch 5 Amp single pole one way

One fan point controlled by switch 5 Amp single pole one way

One bell point controlled by one switch 5 Amp single pole, one way on independent board

One 3 pin 5 Amp socket outlet on same board controlled by one, one way 5 Amp switch

One socket outlet 5/3 pin 5 Amp controlled by one switch on independent board

One light point controlled by switch 5 Amp single pole two way

Ditto all as per Sr Item No 160 (here-in-before) but with 2.5 Sqmm Copper conductor cable for Phase , Neutral and Earth for one 3 pin, 15 Amp socket outlet on independent board

S&F in replacement bell ding dong elelctric 230V AC single pole etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Switch, 6 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Switch, 6 Amp, two way, one Module. etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Switch, 16 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Socket Outlet 6 Amp, 3 pin, combined two module etc as per existing complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Modular Socket Outlet 6 Amp / 16 Amp - 2/3 pin combined two module as per existing etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Bell push, 6 Amp, one module etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Fan Regulator Fan step regulator, 120 Watt - two module etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge

M&L ceiling rose 3 terminal / PVC / polycarbonate, isolated body etc complete all as specified and directed by Engineer-in-Charge

S & F in replacement double door Sheet metal enclosures factory made DBs 4 way TPN, 415 volts ,protection class IP-42, suitable for fixing of MCBs etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed.

S & F in replacement double door Sheet metal enclosures factory made DBs SPN, 8 way ,240 volts ,protection class IP-42, suitable for fixing of MCBs,, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed.

Supply & fixing MCB , SP, AC, 240 Volts of 06 to 40 Amp capacity 10KA, 'B' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing MCBs, TPN, AC, 415 volts of 63 Amps capacity 10 KA, 'B' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing MCBs, SPN, AC, 240 volts of 40 Amps capacity 10 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement square profile LED lighting fixture , environmental friendly, energy efficient ready to use pack Aluminium housing LED Tube light fitiing 22 Watt with LED light source 6500 K,input voltage 160V-270V with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge .

S&F Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 12 Watt with LED light source 6500 K with uniform light output, with all accessories including its connection with 2 core seathed copper conductor cable of size 0.5 Sqmm with etc complete all as specified and directed by Engineer-in-Charge

Supply & fix in replacement energy saving and environmental friendly long life LED street light 25 Watt (Bldg security light) made up of pressure die cast aluminium housing with mild power LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 fixed on wall with GI pipe of suitable dia and all fixing accessories including connecting up with & including twin core twisted flexible copper conductor cable of suitable size of 230V , 50 HZ etc complete all as specified and directed by Engineer-in-Charge

S&F square profile LED lighting fixture with extruded Aluminium housing, environmental friendly, energy efficient ready to use pack LED Tube light fitiing 12 Watt with LED light source 6500 K,input voltage 140V-270V with uniform light output, with all accessories including its connection with 2 core seathed cable of size 0.5 Sqmm with etc complete all as specified and directed by Engineer-in-Charge.Make: Smart bright batten or equvalent in Make .

S&F bed side reading light, wall mounted, flexible rotable, ultra slim spot light 3 Watt cool whitecomplete all as specified and directed .

S&F sub main wiring with two single core PVC insulated,unsheathed, FRLSH stranded copper conductor cable 4 Sqmm with 4 Sqmm PVC insulated, unsheathed, FRLSH stranded copper conductor cable as earth wire drawn through and including PVC Casing and capping ISI Marked with its all necessary accessories and earth wire connected to common earth dolly etc complete all as specified and directed by Engineer-in-Charge Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. Two run of 4 Sqmm cable i.e for one run for phase, one run for neutral with one run of 4 Sqmm cable for earth and one run of PVC Casing & caping shall be measured as one unit

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. Earth pit not less than 2.25 m depth and top edge of the earth plate not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nuts, bolts & washer etc. Earth wire connected upto main earth point / DBs alongwith 15mm dia earth protection pipe from top edge of the earth plate to main earth point to be connected and 20mm dia watering pipe light grade with funnel and provn of PCC using cement concrete (1:2:4) mix type B1 using granded stone aggregate and RCC pit cover 50 mm thick precost RCC (1:2:4) mix type B1 duly reinforced with 8 mm dia of TMT bar @ 100 mm CIC, both way, lifting arrangement complete including all necessary earth work etc complete all as specified and directed by Engineer-in-Charge

Taking out/down and opening of existing ceiling fans 1200 mm sweep,from any position, of any make etc & refixing at the desired location after reassembling and after servicing/overhauling by thouroghly cleaning the shaft,rotor,stator and applying lubricant/grease to bearings and one coat of super enamelled varnish over winding to improve the insulation resistance including repair /replacement of spare parts/ material /items , making connection by replacing PVC insulated unsheathed cable of copper conductor of size 1.50 Sqmm upto 0.50 Mtr length including using material/parts of minor nature such as screws, lugs, insulation tape, nuts, bolts, washers etc after cleaning the metal surface, greasing/lubricant etc to make it functional complete all as specified and as directed.

M&L for preperation of ceiling fans 1200 mm sweep, of any make by cleaning of metal surfaces including painting with spray painting on required gloss with white synthetic enamel paint on complete body of fans and writing MES No with black synthetic enamel paint etc complete all as specified and directed by Engineer-in-Charge

M & L for Supply,laying ,connecting ,testing and commissioning and jointing , LT underground cable in replacement ,1100 volts grade, XLPE insulated, armored with galvanized round steel wire or steel strip, electric power cables heavy duty, with multi stranded aluminum conductor, laid in ducts, fixed on poles/walls with proper size saddles and clamp complete all as specified and as directed by the Engineer-in-Charge of following Sizes :- (a) LT cable 10 Sqmm, 2 core. Note : Excavation, arthwork & protection pipe etc shall be measured and paid seprately under relevent items of this Sch.

Returnig, filling in including spreading, levelling, watering and well ramming in layers, n exc 25 cm thick in soil etc complete all as specified and directed by Engineer-in-Charge

Supply & laying of HDPE DWC pipe ISI marked of outer dia 50 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable icluding coupler and bends etc complete all as specified and directed by Engineer-in-Charge

M&L for cutting to existing CI/GI pipe line upto 80 /50/25 mm dia for taking connection up to 25 mm dia GI pipe including insertion of CI /GITee complete all as specified and directed including Exc & earth Work

S&F 20 mm Ball brass valves,high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

Supply and fix gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed for for 20 mm bore.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Supply and fix electric water heater, storage type steel body and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, including Flexible pipe 2 set , PVC Connection pipe fastner fixed in wall Complete etc.

S & F for plastic body exhaust fan, AC single phase, 240 V of size 150 mm sweep including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed.

Supply & fix in replacemnt industrial type switch socket for Geysers with 20 Amp MCB etc complete all as specified and directed by Engineer-in-Charge

Supply and fix air cooled split Inverter air conditioner electric driven single phase of capacity of 2 TR, BEE 5 star rated,copper condensor,copper condensor complete all as specified

Ms. M.D. Auty (BID ID -3126578)

MS. G.A. CONSTRUCTION (BID ID -3129226)

HG PATHAN CONSTRUCTION COMPANY (BID ID -3129353)

M/S CHHTRAPATI CONSTRUCTION (BID ID -3128734)

Neha Enterprises (BID ID -3129534)

M/s. N D Karande (BID ID -3129463)

Priyadeep Construction (BID ID -3128715)