SPECIAL REPAIR OF BLDG NO P 108 AT KANJOLI LINE BHARATPUR

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground levels) complete all as specified.

M&L for 100 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed & pointed in neat cement slurry in floors with grey cement & pigment over 15 mm thick screed in CM (1:6), complete all as specified.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection/path laid in panel surface finished even and smooth without using extra cement complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the same from premises, complete all as specified.

M&L for coloured non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc. 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, laid over 15 mm thick screed bed in CM 1:6, complete all as specified.

M&L for coloured non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc. 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor, laid over 15 mm thick screed bed in CM 1:6, complete all as specified.

M&L for glazed ceramic tiles, coloured/printed tiles in vertical surface of size 450x300x7 mm thick, laid over 15 mm thick rendering in cement mortar (1:3) and set and jointed in neat cement slurry & pointed in white cement with pigment to match the colour of tiles, complete all as specified.

M&L for 18 - 20 mm thick black machine cut granite slab (of any type) (table rubbed and polished), as in steps, jambs, pillars, window- cills, cooking platform set in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab laid over and including 15 mm thick cement screed in cement and sand mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for rounding to edges of stone slab one edge, such as in steps, cooking platform and other similar situation including making of hole suitable for gas pipe etc. complete all as specified.

Dismantling of Stone slabs in roofs, suspended floors, chajjas, landings, etc any thickness, jointed in any mortar complete all as specified.

M&L for sand stone slabs of 50 mm thick in cills, sun-shades, chajjas, shelves, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4, complete all as specified.

Dismantling asbestos cement (corrugated or semi corrugated) sheets in roof coverings, complete all as specified.

Pre painted galvalume zinc coating GI based corrugated steel sheet 0.50 mm thick, sheeting of any colour having strength of 550 mpa as in roof covering etc, complete all as specified.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections & MS pipe) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A', complete all as specified.

M&L for mild steel work as in wind ties for roof covering including securing bolts etc. including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 290 Gde E-165, complete all as specified.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc complete all as specified.

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc complete all as specified.

S&F GI tubing medium grade ISI marked galvanised with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified.

S&F GI tubing medium grade ISI marked galvanised with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified.

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm including brackets & waste coupling, pipe of polythelene of low or high density complete all as specified.

S&F pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shank and fly nuts, with or without lettered "Hot" or "Cold" suitable for 15 mm nominal bore iron pipe, screwed for iron pipe and fixed complete all as specified.

S&F in repair Sinks kitchen or laboratory with plugs, washers and wastes including beding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe; exc 0.5 sqm each all as specified.

S & F in repair of chromium plated shower rose 125 mm dia with 200 mm long CP arm with swivel joints, any size, including fixing to steel pipe or union complete all as specified.

S&F in repair of Tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified.

S&F in repair vitreous china wash down water closet (Pedestal pattern) white with seat cover excluding (flushing cistern and flush pipe), complete all as specified.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white, 10 lit capacity with inlet, ball valve, float and handle including brackets, flush pipe complete all as specified.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm including complete all as specified.

S&F in repair Bib tap, cast copper alloy, fancy type long body with crutch or butterfly handle, screwed down, suitable for 15 mm nominal bore iron pipe screwed for iron or brass ferrule and fixed complete all as specified.

S&F in repair 15 mm bore stop valves, chromium plated, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified.

S&F in repair 15 mm bore stop valves, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type), screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified.

S&F in repair Waste coupling of PTMT (half or full threaded) of 40 mm bore dia of discarge pipe . (Minimum weight 40mm- 60gms complete all as specified.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified.

S/F in repair PVC (SWR) floor trap 75mm dia plain with stainless steel grating including jointing with solvent cement complete all as specified.

S & F 500 ltr ISI marked three layer, white colour, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) with thread type cover and fixed with screw hoisted and fixed in position & including 20 mm brass ball valve of PTMT with epoxy coated aluminum rod complete all as specified including dismantling existing tank.

M & L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified.

S&F of welded steel wire fabric ,weight n. exc 4.00 kg/sq. m fixed to steel members complete all as specified.

S&F 1.00 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets or welded and fixed to steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning upmitred angles etc as required complete all as specified.

Demolition & breaking up drain pipes AC, (Salt glazed ware, AC or Reinforced concrete) set in CM Internal dia of pipe 100 mm/75 mm complete all as specified.

S&F PVC (SWR) pipe not less than 6 Kgf/sqcm rating single socketed, in any length with rubber ring joints including clamps of FI 40x3 mm fixed bolt 8 mm drilled to wall, in walls, type 'B' ISI marked of 110 mm bore complete all as specified.

S&F PVC (SWR) pipe not less than 6 Kgf/sqcm rating single socketed, in any length with rubber ring joints including clamps of FI 40x3 mm fixed bolt 8 mm drilled to wall,in walls, type 'B' ISI marked of 75 mm bore complete all as specified.

S&F in repair PVC (SWR) bend of 110 mm bore with access door of any radius complete all as specified.

S&F in repair PVC (SWR) bend of 75mm bore with access door of any radius complete all as specified.

S&F in repair PVC (SWR) Vent cowl of 75mm bore complete all as specified.

S&F in repair PVC (SWR) single T of 110 mm bore equal or un equal complete all as specified.

S&F in repair PVC (SWR) single T of 75 mm bore equal or un equal complete all as specified.

Taking down chowkats or frames n. exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified.

Taking down chowkats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters (without taking off shutters from the frame) complete all as specified.

S&F Plain, framed, panelled shutters 40mm thickness (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified.

S&F factory made, 35 mm thick, 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified 8.24(a) in SSR Part I complete as as specified.

S & F for Solid PVC Door Frame of the size 50 x 47mm made out of 5 mm PVC sheet. The door profiles are to be reinforced with 19x19mm M.S Square tube. The profile shall be cut and mitred at two corners and joined by inserting 2nos. of 150mm long brackets of 15x15mm M.S. square tube inside the 19mm x 19mm M.S. square tube and suitably screwed complete all as specified.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified & shown on SSR 2020 (Part-II) complete all as specified.

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 48x40 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 Nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge.

S&F MS butt hinges medium weight cold rolled of size 100 mm, complete all as specified.

S&F stainless steel hinges medium weight of size 100 mm, complete all as specified.

S&F aluminium anodised,barrel tower bolts of extruded section, 200 mm length of bolt and fixed with screws, complete all as specified.

S&F 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws complete as as specified.

S&F Aluminium handles, cast type, anodised of 125 mm size complete all as specified.

S&F aluminium deco grill in door and windows with weight not exceeding 1.00 Kg/Sqm including necessary arrangement for fixing etc complete all as specified.

S & F Sheet glass 4.0 mm thick, ordinary quality & glazing with oil putty in squares n.exc 0.5 sqm in each pane including punching or drilling out old glazing pins/spring clips, and providing & fixing new ones complete all as specified.

S&F for Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples or rivets, complete all as specified.

S&F Door closer hydraulically regulated designation No 2, universal type, of aluminium (extruded section body), suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed, complete all as specified.

S&F 100 mm mild steel 4 lever mortice lock vertical type of size complete all as specified.

Demolition of brickwork or stone boulder masonry built in cement mortar including all quoins, arches, pillars etc, complete all as specified.

M & L for brick work with sub-class 'B' bricks, straight or curved on plan exc 6.0 metre mean radius as wall built in cement & sand mortar 1:6, complete all as specified.

M&L for bricks, sub class B, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified.

Taking down cement or cement lime plaster of any description from brick or stone walls including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified.

M&L for rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified.

M&L for rendering 5 mm thick in cement and sand mortar 1:3 on fair faces of concrete surfaces as in ceiling including finishing the surface even and smooth without using extra cement, complete all as specified.

M&L for rendering 15 mm thick in cement and sand mortar 1:4 on brick work or cement concrete surfaces including finishing the surface even and smooth, complete all as specified.

M&L for preparation of newly plastered or un plastered surfaces of walls and applying two coats of oil emulsion distemper white or tinted over one coat of water based white pigmented alkali resistant priming paint, over 1 mm thick wall care putty on Wall Surface including all necessary arrangement for execution of work ,complete all as specified.

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of oil emulsion distemper white or tinted complete all as specified.

M&L for complete removal of existing treatment in wall applying two coat of Exterior emulsion paint for external wall Surface over one coat of alkali resistant primer complete all as specified.

M & L Preparation of new decorated plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of Exterior emulsion paint over a coat of alkali resistant primer complete all as specified.

M&L for painting to new or previously untreated steel surfaces of any description over 10 cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chrome primer including preparation of surfaces complete all as specified.

M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for one coats painting with synthetic enamel paint to old wood or wood based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface complete all as specified.

M&L for complete removal of existing treatment and applying two coat of oil bound distempering white or tinted over one coat of alkali resistant priming paint on wall surface including all necessary arrangements for execution of work complete all as specified.

Ditto all as per Srl item No 81 here in above but applying one coat of distemper oil emulsion white or tinted on ceiling complete all as specified.

Cutting or uprooting grass incl removing old mud phuska/ roof treatment of 100mm thickness and description, removing rubbish off the premises, cleaning surface and preparing to receive new treatment complete all as specified.

M&L for 20 mm thick screed bed or bedding layer of cement mortar 1:4, finished even and smooth without using extra cement complete all as specified.

Providing and laying APP(Atactic Polypropylene polymer) modified prefabricated five layer 4mm thick water proofing membrane,black finished reinforces with nonwoven polyester matt consisting of a coat of bitumen primer of bitumen membrane @ 0.40 litre/sqm by the same membrane manufacturer of density at 25 degree C 0.87-0.89 Kg/litre and viscosity 70--160cps.Over the primer coat the layer of membrane shall be laid using Butane torch and seiling all joints etc and preparing the surface complete. The vitalphysical and chemical parameters of the membarane shall be as under: Joint strength in longitudinal and transvrese direction at 23 degree C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membarane not less than 150 degree C. Cold flexibility shall be up to -2 degree C when tested in accordance with ASTM,D

S&F in repair for 18 mm thick PVC boarding shelves of density exc 550 Kg per Cum but nexc 600 Kg per Cum one side decorative lamination & other sidebalancing lamination sheet fixed with brackets, screws etc with sliding glass shutters with all fixing arrangements, Panels shall be fabricated using adhesive and screws wherever required, Supported for three sides with 18 mm x 18 mm PVC Ply fixed with Screw all the edges shall be coverd with 18 mm x 1 mm thick edge bending tape or 90 degree edge bend finish as per manufactrure specification or approved pattern complete all as specified. Note : Glass shall be measured and paid seperately.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or from metal frame or stone or concrete or bricks surrounds glazesd with putty, taking out old pins punching or drilling out, complete all as specified.

S&F in repair for Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples or rivets, complete all as specified.

Dismantling wall and ceiling boards ( fibre, pulp, insulation ,etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified.

S&F anodised aluminium snap grid frame work of grid size 605 x 605 mm for false ceiling complete all as specified.

S&F for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

S&F for 4 mm thick non-asbestos fibre cement building boards fixed to aluminium framework, complete all as specified. Note: Frame work for ceiling shall be measured and paid separately)

S&F for PVC wall panelling in repair with panel of 300 mm x 6 mm Hollow section of Sintex pattern SPUF- 146 or equivalent , fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/ window/openings etc to be covered with PVC angle fixed with solvent cement complete all as per manufacturer's instructions complete all as specified.

M&L in replacement concealed point wiring complete with 1.5 Sqmm 02 x single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in PVC conduit pipe size not less than 20 mm dia with all PVC accessories such as Tee, bend, collar, elbow, square junction box etc fixed on the concealed surface and making good the disturbed surfaces of wall/ceiling by means of Wall putty and matching colour of existing wall, PVCsleeve /dash fastners with cadmium plated screws including suitable size of PVC boards/ sunken box for mounting fittings like switches, sockets, fan regulator etc including 1.5 Sqmm PVC insulated but FRLS unsheathed copper earth continuity conductor to common earth and connected to earth dolly complete all as specified for the following :-

(a) One light point controlled by one way switch.

(b) One fan point controlled by one way switch.

(c) One bell/buzzer point controlled by one push button.

(d) One 3 pin 6 Amp socket point outlet on the same board with other switches

(e) One 3 pin 6 Amp socket point outlet on the independent board

All as per item No 94 above but with multi stranded copper conductor cable 2.5 Sqmm size for 3 pin 16 Amps socket point outlet on independent board including 2.5 Sqmm copper cable PVC insulated FRLS unsheathed copper continuous earth wire including connecting to common earth dolly complete all as specified.

S&F ceiling rose surface bakelite three terminal ISI marked including suitable size of PVC board.

S&F Socket outlet 2 in 1, 5 pin, 5 and 15 amp flush type multi purpose flush type 230 volt complete.

S&F switch piano flush button single pole one way 6 Amps 230 volt grade complete.

S&F switch piano flush button single pole one way 16 Amps 230 volt grade complete.

S&F socket 5 pin 16A, flush type complete.

S&F in repair step type electronic fan regulator EME type 100 watt complete.

M&L submain wiring complete with 4 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 4 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduit of size 20mm /sleeves with all PVC accessories fixed on wall, floor/ceiling etc. Note: Two runs of 04 sqmm and one run of 04 sqmm earth conductor and PVC conduit pipe shall be measured as one length only.

M&L submain wiring complete with 6 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 6 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduitof size 20mm/sleeves with all PVC accessories fixed on wall, floor/ceiling etc. Note: Two runs of 06 sqmm and one run of 06 sqmm earth conductor and PVC conduit pipe shall be measured as one length only.

M&L concealed submain wiring complete with 10 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 10 Sqmm copper cable for earth continuity conductor in and including drawn through PVC conduit size not less than 25 mm dia with all PVC accessories. Note: Two runs of 10 sqmm and one run of 10 sqmm earth conductor and PVC conduit pipe shall be measured as one length only.

S&F in replacement of vertical TPN 8 way Distribution board double door, prewired for mounting of MCCB /MCB isolator, ELCBs etc factory made, confirming to IS: 13032 fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral link and bus bar. DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and baked at high temperature, painted in seven tank process. The DBs shall be of IP 43 protection class. Make : Havells/Legrand/Indoasian

Supply and fix of distribution board factory made and tested made of sheet metal enclosure powder coated suitable for mounting the MCB 240 volt, 415V of the following DBs.

(a) 4 way TPN with busbar 415 volts (double door)

(b) 8 way SPN with 200 amps rated busbar 240 volts (double door type).

(c) 4 way SPN with 200 amps rated busbar 240 volts (double door type).

S&F MCB's of following capacity :-

(a) MCB TPN 63 Amps 415 volt, Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

(b) MCB SP 6-32 Amps, 240 volts,Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

(c) MCB SPN 40-63 Amps, 240 volt,Category- C curve, 10kA rapturing capacity ( ISI marked IS-8828)

S&F in replacement of MCCB 4 pole, 415 volt , adjustable thermal and magnetic release type 100 Amp breaking capacity 25 KA complete all as specified.

Supply and fixing of 18/20 watt LED tubelight fitting retro fit type 4Xfeet long with replacable rod complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, complete all as specified.

Supply and fixing sensor based 20 watt LED tubelight fitting batten type 4 X feet long with rod complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, complete all as specified. Make Havells of Model No: R20RBA or equivalent in crompton / Phillips

Supply and fixing LED mirror light fitting with high out put with low energy consumption of capacity 6 watt,waterproof moisture anti-fog anti-corrosion anti-rust,curved LED off-white including connecting up with three core flexible copper conductor cable of suitable size complete.

M&L bracket light fitting wall mounting, champagne gold finish fixture with plastic body suitable for 14 W LED lamp B22 base complete all as specifeid.

S&F in repair lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings all incl 9watt LED lamp complete all as specifeid.

S & F in repair street light GI bracket of 0.6 mtr long made out of 40mm dia light grade GI pipe bend to shape of 120 degree end welded at required including 02 Nos MS clamp of FL 40 x 6mm including nuts bolts & washers complete necessary fixing arrangements on pole complete all as specifeid.

S&F in repair 35/36 watts LED street light fitings new generation energy saving, environmental friendly, long life, versatile pressure die cast aluminium IP66 with 10KV surge protection road way, luminaire with high power LED as light source connecting with 2.5 sq mm solid aluminium conductor PVC insulated twin core weather proof cable from fittings to over head lines or to the jucntion box and fixing to complete all as specified.

S&F LED Recessed full lit luminaire with glare free uniform illumination 2 ft x 2 ft, 35/36 Watt , complete with all accessories internally pre-wired and including connecting to ceiling rose with three core flexible copper conductor cable of size 1Sqmm complete all as specifeid.

S&F sheet metal enclosure of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of SP 20 Amps, 240 volts complete all as specified.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300msweep with, blades, and frame and louvers complete all as specifeid.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450 mm sweep with, blades, and frame and louvers complete all as specifeid.

Material and labour for cutting suitable holes in existing masonary wall and fixing suitable size hume pipe for fixing of exhaust fan 450/300 mm dia and making good disturbed surfaces with cement mortar (1:4) and finished to match existing surface complete all as specified.

M & L in repair for Earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm buried directly in the ground vertically to depth not less than 2.25 Mtr below the ground level with the top edge of earth plate, depth not less than 1.50 Mtr below the ground level connected to GI earth wire 4mm dia by means of bolts, nuts and washers protected by GI tubing light grade 15 mm dia uptoTest point, 20 mm dia GI watering pipe medium grade with funel & wire mesh, PCC pit in PCC 1:2:4 using 20 mm stone aggregates chamber 40 mm thick RCC cover slab (1:2:4) type B-1 using 20 mm graded stone aggregates with 8 mm reinforcement bors @ 15 cm c/c bothway complete all as specified and shown in electrical plate No.3 of SSR Part-I including earth work in soft/loose soil ,removal of surplus sil and providing charcol dust & salt layers all around the earth plate upto 15 cm complete all as specifeid. (Note:- Up to7.5Mtr length of pipe of 15 mm dia and GI wire shall be deemed tobe included in unit rate quoted by tenderer GI pipe and GI strip beyond 7.5) will be measured separately under respective item

S&F ceiling fan (white) of 1200 mm sweep, 5 star rating copper wound with super energy efficient BLDC motor including remote,connecting wire PVC insulated twisted flexible 0.5 sqmm copper conductor canopy set, down rod, shackle kit, including all standard accessories and deposit old unseviciable fan deposited to AGE E/M Yard complete all as specifeid.

Excavation in trenches, n. exc 1.5 Mtr wide and n. exc 1.5 Mtr in depth for foundation/laying of cable and getting out in soft/loose soil complete all as specified.

Removing of excavated soil to a distance n. Exc 50 Mtr and depositing where directed at a level n. Exc 1.5 Mtr above the starting point complete all as specified.

Returning, filling in including spreading, levelling, watering and well ramming in layers n. Exc 25 cm thick complete all as specified.

Supply & spread unwashed dry river sand for sand cushioning and covering the under ground cable in trenches. (Note :- Punning thickness shall be measured.) complete all as specified.

M&L for brick protection with sub Class`B` bricks old size laid dry, flat over cable perpendicular across the cable in trenches complete all as specified.

Supply, laying, testing & commissioning LT XLPE insulated armoured (heavy duty) electric cable with stranded aluminium conductor 1100 volts grade (ISI marked) & laid in trenches/pipes or fixed on pole of the following sizes:-

(a) 70 Sqmm 3.5 core

(b) 16 Sqmm 4 core

(c) 10 Sqmm 2 core

Boring of holes under road, pavement, hard standing by suitable tools and machinery for laying of pipe upto 80 mm bore complete all as specified. Note :- GI pipe shall be measured and paid separately.

S & F or laying galvanised steel tubing light grade (ISI marked) for protection of under ground cable on poles/walls under road crossing of 50 mm bore. Size complete all as specified.

Material and labour earthing complete with galvanized iron earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m deep below normal ground connected to galvanised GI strip of size 32 x 6 mm by means of bolts nuts check nuts and washer of galvanized steel, watering pipe of 20 mm bore galvanised iron medium grade and 40 mm bore galvanised iron light grade for earth strip protection including all excavation earth work in any type of soil, PCC pit in PCC 1:2:4 type B-1 and RCC 1:2:4, type B1 for precast chamber cover 50 mm thick, reinforced with welded steel wire fabric or XPM Jali (weight not less than 4.00 Kg / sqm), with charcoal, salt, funnel complete all as shown in the electrical plate No 3 of SSR part –I and testing on completion.Note:-Quoted rates shall be deemed to include for earth strip with protection pipe up to 7.5 M length.

Taking up or down G.I. tubing and connection of size 25 mm bore complete all as specified.

All as per item No 132 above but 40 mm dia bore

All as per item No 132 above but 50 mm dia bore

All as per item No 132 above but 80 mm dia bore

S&F GI tubing medium grade ISI marked including all fittings laid in trenches / fixed on wall of size 25 mm bore complete all as specified.

All as per item No 136 above but 40 mm dia bore

All as per item No 136 above but 50 mm dia bore

All as per item No 136 above but 80 mm dia bore

M&L in repairs gun metal gate or globe valves with iron wheel head (ISI Marked), screwed both ends for iron pipe and fixed of size 25 mm dia bore complete all as specified.

All as per item No 140 above but 40 mm dia bore

All as per item No 140 above but 50 mm dia bore

M & L for construction of brick masonry vavle pit of internal dimension 900mmx900mmx900mm depth with sub class "B' bricks in cm (1:4) and 10 mm thick plastering in CM(1:4),PCC (1:4:8) type D2 (Using 40mm grade broken stone aggregate) as in foundation lean concrete PCC (1:3:6) type CI (Using 20mm grade broken stone aggregate ) as in bedding and copping MS frame with 40x40x6mm angle iron 3 mm thick MS sheet cover plate with locking arrangement, hinges and two coats of sythetic enamel paint over one coat of red oxide primer including preparation of surface three coats of white wash on plaster surface (exposed to view) including necessary excavation in soft loose soil returning filling in and removal of surplus soil to a distance not exceeding 50 m complete all as specified.

M & L for construction of brick masonry vavle pit of internal dimension 600mmx600mmx600mm depth with sub class "B' bricks in cm (1:4) and 10 mm thick plastering in CM(1:4),PCC (1:4:8) type D2 (Using 40mm grade broken stone aggregate) as in foundation lean concrete PCC (1:3:6) type CI (Using 20mm grade broken stone aggregate ) as in bedding and copping MS frame with 40x40x6mm angle iron 3 mm thick MS sheet cover plate with locking arrangement, hinges and two coats of sythetic enamel paint over one coat of red oxide primer including preparation of surface three coats of white wash on plaster surface (exposed to view) including necessary excavation in soft loose soil returning filling in and removal of surplus soil to a distance not exceeding 50 m complete all as specified.

S&F in repair of sluice valve 80 mm dia bore class PN- I.6 with flanged and iron wheel head, shut and open directed cast on it and including jointing materials, rubber gasket suitable size nut bolts and washer etc complete all as specified.

GANGA CONSTRUCTION (BID ID -3472473)

BHARDWAJ CONSTRUCTIONS (BID ID -3465870)

PD GUPTA AND COMPANY (BID ID -3471620)

Swastik Engineering Works (BID ID -3468002)

K P BUILDERS (BID ID -3468012)