ADDITIONAL AND ALTERNATION TO RANGE AT ATS BELAGAVI UNDER GE (AF) SAMBRA.

Amount

Dismantling wall hearth tiling including cement mortar bedding (but not backing) and removing unserviceable material complete all as specified and as directed.

Demolition of un-reinforced cement concrete in ground floor and pavings not exceeding 15 cm thick (below or above ground level) and removing all the rubbish complete all as specified and directed

Demolition of brickwork or stone/boulder masonary, build in ashlar facings,dressed stone work,precast concrete block articles and pre cast concrete block walling including all quoins, arches, pillars, etc., complete all as specified and as directed

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar of 100 mm/ 75 mm bore complete all as specified and as directed

Dismantling framed work timber scantlings 40 sqcm and over in section, in any position complete all as specified and as directed

Dismantling framed trusses span not exc 10cm of any decription ans in any position complete all as specified and as directed

Dismantlimg galvalume aluminium Zinc coating GI based corrugated steel sheet 0.50mm thick sheets in roof coverings invld ridges complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

Excavation in trenches not exc.1.5m wide and not exc 1.5 m depth for sewage line and manholes, drain etc and getting out in hard/dense soil complete all as specified and as directed

Taking down cement rendering/plastering of any thickness and of any description including racking out joint, hacking for key, scrubbing down with water etc., over wall or ceiling surface complete all as specified and as directed

M&L for non - skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles set and jointed in neat cement slury laid over and including 15mm thick screed bed in CM(1:6) complete all as specified and as directed

M&L for glazed ceramic tiles of size 350x 250x 7 mm/ 450X 350X 7mm thick in vertical surfaces such as skirting, dado, etc.., set and jointed in neat cement slurry and pointed in white or colour cement to match match the shade of tiles set and jointed in neat cement slury laid over and including 10mm thick screed bed in CM(1:4) complete all as specified and as directed

Taking up or down 15 mm bore GI/PPR/PVC tubing and connections along with fittings such as tees , bends etc fixed to walls and ceilings or laid in floors/ trenches complete all as specified and directed.

Taking up or down 20 mm bore GI/PPR/PVC tubing and connections along with fittings such as tees , bends etc fixed to walls and ceilings or laid in floors/ trenches complete all as specified and directed

S&F unplasticised PVC pipes of pressure rating 10 kgf/Sqcm fixed complete to walls, ceilings or in floors etc., any type of pipe including fitting such as bends,elbows, unions, tees, reducing tees, adopters, sockets, plugs, hose clips, brass fittings etc for 15mm bore complete all as specified and directed

S&F unplasticised PVC pipes of pressure rating 10 kgf/Sqcm fixed complete to walls, ceilings or in floors etc., any type of pipe including fitting such as bends,elbows, unions, tees, reducing tees, adopters, sockets, plugs, hose clips, brass fittings etc for 20mm bore complete all as specified and directed

S&F vitreous China wash down water closet pan ( padestal pattern ) white,(excluding flushing cistern and flush pipe ) but including connceting to trap set & flushing pipe complete all as specified & directed.

S&F in repairs vitreous China suatting pan Orissa pattern fixed in repairs size 580mm x 440mm white with intergal fooot rest (excluding flushing cistern )complete all as specified and as directed.

S&F wash hand basin, vitreous China, white, flat back, 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F 15mm dia fancy angle valve, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or round handle screwed bolts ends for iron pipe or for unions including CP finish copper alloy cup washer complete all as specified and directed.

S&F two way chromium plated bib cock will wall flange screwed for iron pipe/CPVC/UPVC or for brass ferrule and fixed complete all as specified and directed

S&F 15 mm dia bore, Bib tap standard of PTMT any colour high pressure screwed for iron pipe (Minimum weight 90gms) complete all as specified and directed.

S&F 15 mm dia bore Pillar taps of PTMT any colour high pressure screwed for iron pipe (Minimum weight 110gms) complete all as specified and as directed.

S&F health faucet mild steel Cromium Plated suitable for 15mm dia pipe with 1.25 metre flexible tube with wall hook fixed complete all as specified and directed.

S&F PVC low level flushing cistern complete with syphonic action type 10 Ltr capacity including flange valve handle, bracket, PVC flush down pipe with bend complete all as specified and directed.

S&F framed work as in doors or gates of hallow section Fe 410 (Gde-E-250 quality -A with gusset plates, rails, braces, etc.complete, drilled for fixing of steel sheeting or other covering, doors to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and directerd

S&F PVC connection 15 mm dia with PTMT nut of length 450 mm complete all as specified and directerd

S&F PVC connection 15 mm dia with PTMT nut of length 600 mm complete all as specified and directerd

S&F in replacement PVC SWR pipe 75 mm bore, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in replacement PVC SWR pipe 110 mm bore, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC SWR pipe 75 mm bore, single socketed in any length with rubber ring joints, fixed to walls including suitable size mild steel clamps complete all as specified and directed.

S&F PVC SWR pipe 110 mm bore, single socketed in any length with rubber ring joints, fixed to walls including suitable size mild steel clamps complete all as specified and directed.

S&F 75 mm dia PVC (SWR) bend of any radius complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bend of any radius complete all as specified and directed.

S&F 110 mm dia PVC vent cowl complete all as specified and directed.

S&F 110 mm dia PTMT grating doom (Minimun weight 25 gms.) complete all as specified and directed.

S&F 125mm dia PTMT grating doom (Minimun weight 25 gms.) complete all as specified and directed.

Taking down and refixing of shutters of any description (wooden, aluminium, mild steel) in same opening of any description exc 1 Sqm but not exceeding 2 sqm, including easing, adjusting and also refixing builders hardware as required including renewal of unserviceable screws ,necessary welding complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 50 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicityindex of 12 for 100 gms) having minimum density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/Sqmm, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed.

S & F 100 mm long mild steel butt hinges medium weight cold rolled complete all as specified and directed.

S & F 150 mm long extruded aluminium alloy anodised handle fabricated type complete all as specified and directed.

S & F 150 mm long aluminium anodised barrel tower bolt complete all as specified and directed.

Taking down chowkhats or frame not exc 1.5 sqm with shuttter ( without taking off shutter from the frames) complete all as specified and directed.

M&L for plain cement concrete type D2, 1:4:8 (using 20mm graded stone aggregates) as in foundation filling and mass concrete complete all as specified & as directed .

M&L for pre-cast cement concrete 1:3:6, type C1 (using 20 mm graded stone agrregates) as in solid block masonary exc 10cm width having minimum compressive strength of 50 kg/sq cm as per IS 2185 (Part I) 2005 and set in cement mortar 1:6 complete all as specified & directed

M&L for pre-cast cement concrete 1:3:6, type C1 (using 20mm graded stone agrregates) as in solid block masonary exc 10cm width having minimum compressive strength of 50 kg/sq cm as per IS 2185 (Part I) 2005 and set in cement mortar 1:6 complete all as specified & directed

S&F tubular trussess RHS including special shadep ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St-240 in main and cross beams, hip and jack rafters; purlins fixed with other connecting tubular trussess etc of Fe 290 (Gde E-165) complete all as specified and directed.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws complete all as specified and directed.

M&L for plain cement concrete 75 mm thick, 1:2:4 , type B1 (using 20 mm graded stone aggregates) for subbases, floors & pavings and plinth protection complete all as specified & as directed .

M&L for 15 mm thick cement plaster in CM 1:6 on fair faces of wall surfaces finished even & smooth without using extra cement complete all as specified & as directed .

M&L for 15 mm thick cement plaster in CM 1:4 on other than fair faces of wall surfaces finished even & smooth without using extra cement complete all as specified & as directed . Note:-Water proffing compound shall be measured and paid separately as "Supply only"

M&L for roughening surfaces of old concrete floor by picking ,sweeping clean and washing down with water to remove dust complete all as specified & as directed .

M&L for 250mm thick cement concrete , type D2 1:4:8 using 40mm stone agg as in sub base under floor complete all as specified & as directed .

M&L for 100mm thick cement concrete , type B2 1:3:6 using 40mm stone agg as in sub base under floor complete all as specified & as directed .

M&L for 50mm thick cement concrete , type B1, 1:2:4 (using 20mm stone aggregates) as in floor complete all as specified & as directed .

M&L for glass dividing strips of width 22mm , 3mm thick inserted in position complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm, soil retreived from excavation complete all as specified & as directed .

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified & as directed .

M&L for two coats synthetic enamel paint on new steel surfaces of any description, over 10cm in width or girth, not otherwise described over 10 cm width or girth complete all as specified & as directed .

M&L for applying three coats of white wash on new decorated surfaces of walls, pillasters, cornices, etc., including necessary preparation of surfaces complete all as specified & as directed .

M&L for applying two coats of white wash on old decorated surfaces of walls, pillasters, cornices, etc., including necessary preparation of surfaces complete all as specified & as directed .

M&L for preparation of new surfaces of wall and applying two coat of cement based paint complete all as specified and as directed.

M&L for preparation of old surface of wall and applying a coat of cement based paint complete all as specified and as directed.

M&L for applying two coats of white wash on new surfaces of ceilings including necessary preparation of surfaces complete all as specified & as directed .

M&L for PCC (1:3:6) type C2 (using 40 mm graded stone aggregates) for concrete bed to drain pipes including packing under and haunching against side of pipes 200 mm bore after they are laid down, jointed and tested complete all as specified & as directed .

M&L for PCC (1:3:6) type C2 (using 40 mm graded stone aggregates) for concrete bed to drain pipes including packing under and haunching against side of pipes 300 mm bore after they are laid down, jointed and tested complete all as specified & as directed .

M&L for reinforced concrete pipes, class NP2, 300mm dia, laid and jointed complete with collars complete all as specified and as directed.

M&L for reinforced concrete pipes, class NP2, 200mm dia, laid and jointed complete with collars complete all as specified and as directed.

Surface excavation not exc 30cm deep and average 15cm deep and getting out in hard/dense soil complete all as specified & as directed .

M&L for hardcore of gauge not exc. 63mm of broken stone or boulders deposited, spread and levelled in layers not exc. 15cm thick, watered andrammed to a true surface complete all as specified and directed

M&L for machine pressed precast concrete interlocking paver block any shape and size conforming to IS-15658-2006 of 80mm thickness, M-40 grade with grey cement and pigment interstices complete all as specified & as directed .

M&L for providing precast cement concrete in PCC 1:2:4, type B-1 (using 20mm graded stone aggregates) as in kerb stone finished smooth using extra cement including necessary mould/form work complete all as specified & as directed .

Removal of surplus soil exc 250m but n exc 500m depositing where directed at a level not exc 1.5m above the starting pt.

M&L for plain cement concrete 1:2:4, type B1 (using 20mm graded stone aggregates) as in coping complete all as specified & as directed .

M&L for pre-cast cement concrete block masonry with solid blocks,in PCC 1:3:6, type C1 (using 20mm graded stone aggregates) exc 10cm in width and setting in CM 1:4 complete all as specified and directed

M&L for pre cast reinforced cement concrete 1:2:4, type B1 (using 20mm graded stone aggregates) as in cover slab set in cement mortar 1:4 complete all as specified and directed. Note:- Reinforcement shall be measured and paid separately.

M&L for TMT bars 6mm dia to 8mm dia cut to length, bent to shape required,including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for TMT bars 10 mm dia and over cut to length, bent to shape required,including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Cutting exising manholes for connecting new drains,of internal dia if 150 mm making good to pipe and rendering, cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete all as specified and directed..

M&L for formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and as directed.

M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granitecomplete in all respect as specified & directed.

S&F mild steel base plates (plain ) square cut or notched (ordinary and counter sunk)Fe 410 w(Gde-E-250) quality forming holes, without any attachment complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc., complete all as specified and directed

Taking down carefully unserviceable main switches/DBs/metal socket off size including MCBs complete all as specified and directed

M&L for point wiring for the following with stranded FRLS copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid PVC concealed conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including MODULAR METAL FLUSH BOX ,modular white cover plate any size with support frame any size module complete all as specified and as directed. cover of approved make, for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed:-

One light point controlled by one, one way switch 5 Amp

Socket point on the same board

All as per Srl item No 89 above but one 3 pin socket outlet 15 Amps independent with cable 4 sqmm size -ditto-

S&F switch Modular type single pole 6 Amps one way switch AC 230V, 50HZ supply complete all as specified and as directed. Make : Cat Part No. 800100 of Indo Asian ELVIRA/ACWSXXW101 of Havells CRABTREE(Signia) or equivalent make as specified in list of makes of Particular Specifications as approved by GE.

S&F switch Modular type single pole 16 Amps one way wwitch with indicator AC 230V, 50HZ supply complete all as specified and as directed. Make :Cat Part No. 800105 of Indo Asian ELVIRA/ACWSXIW161 of Havells CRABTREE (Signia) or equivalent make as specified in list of makes of Particular Specifications as approved by GE.

S&F Modular type socket 5A AC 230V, 50HZ complete all as specified and as directed. Make : Cat Part No.802800 of Indo Asian ELVIRA/ACWKPXW063 of Havells CRABTREE (Signia) or equivalent make as specified in list of makes of Particular Specifications as approved by GE.

S&F Modular type socket combine 6A/16A multi purpose AC 230CV, 50Hz complete all as specified and as directed. Make :Cat Part No.800122 of Indo Asian ELVIRA/ACWKCXW163 of Havells CRABTREE (Signia) or equivalent make as specified in list of makes of Particular Specifications as approved by GE.

S&F ceiling rose, surface backelite three terminal 240 volts complete all as specified and as directed.

S&F LED lights fitting 1x 20W, 220V, wall mounted LED batten with Aluminum Housing & integrated electronic driver including connecting up with 0.5 Sqmm three core flexible copper conductor cable from ceiling rose complete all as specified and as directed. Make:-Cat Part No: LUMILINE+BS20WLED830SPCSSIND of Havells or equivalent make as specified in list of makes of Particular Specifications as approved by GE.

S&F in replacement sub main wiring in PVC casing caping min 25 mm dia with 2 single core 06 sqmm multi-stranded PVC insulated cable unsheathed 1100 volts grade with one earth wire of 06 sqmm copper conductor cable connected to common earth dolly complete and including PVC casing caping complete all as specified and as directed Note two runs of 6 sqmm and one run of 6 sqmm shall be measured as 1 RM.

S&F sheet metal enclosure double door factory made distribution board 240 volts SPN 4 way, 200 Amps rated bus bar complete all as specified and as directed.

S&F sheet metal enclosure double door factory made distribution board 240 volts SPN 8 way, 200 Amps rated bus bar complete all as specified and as directed.

M&L for MCB SPN 6 to 32 Amps, C Curve, 240 volts, 50 Hz AC supply complete all as specified and directed.

M&L for MCB SP 06 to 32 Amps, C Curve, 240 volts, 50 Hz AC supply complete all as specified and directed.

S&F in replacement of LED based Flood lights, housing made of pressure die cast aluminium alloy with effective thermal management sturdiness. The fixture should have a minimum system efficacy of more than 80 lumen/Watt and a minimum system lumen output of not less than 7600 lumens and maximum system wattage 70 watts. The fuxture shall have a color temperature of minimum 5700 k at a CRI of minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance, lngress protection of IP66 (lamps and gear compartment and Mechanical Impact) Resistance Rating of IK>= 05. The fixture should comply with the parameters as per IEC 60598 and IS 10322, and LED drive should apply to IEC 61000-3-2 ed 3.2. per haronics IEC 61347-2-13, 2006 in confirmation with IEC 61347-1 ed, 2.0, 2007 for electrical safety, LM 79 and LM 80 test report needs to be sumitted above parameters. The fixture driver should have an operating voltage range of 140-300V, frequency 50-60 Hz, surge protection not less than 4KV, PF>0.95 and THD<15%. The driver should have double phase protection. LED lights fitting should be suitable for ambient temperature from (-) 10 digree C to (+) 50 digree C, including street light GI bracket 40 mm dia bent to shape 1200 with suitable size clamp, nut bolts and washers as per site requirement complete all as specified as directed by Engineer-in-charge. (Note-The manufacture of LED fitting shall give Guarantee for 5 years from the date of installation and complete fixed with suitable bracket & Accessories) complete all as specified and directed. Note : Minor Repair ( Oil greasing, chain pulley system, Motors repair , clamps , nut & bolts etc as site required ) for high mast light deemed to included in rate quated.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metre depth below normal ground level) with top edge of plate at a depth not less than 1.5 mtr below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected to galvanized earth wire 04 mm dia with and including bolts, nuts, check nuts and washers of galvanised iron or steel and riveted to earth plate and one end and connecting to main switch board or metallic bodies of HT/LT equipments etc at the other end, GI wire encased in and including 15 mm bore GI light grade pipe with all fittings, from top of electrode to body of equipment fixed with and including flatiron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI light grade and including funnel, wire mesh, copper lugs etc from bottom of earth pit to top of electrode complete with earth pit in PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate and CI cover complete all specified and shown in electrical plate No 03 of SSR Pt-I connecting earth electrode to test point with and including earthing lead including neessary excavation and earthwork in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50m, material and labour complete all as specified and as directed. (Notes 1. The rate quoted shall be deemed to include for all the above provisions. 2. PCC chamber shall be constructed at least 1.5 m away from the earth electrode and pipe for watering shall be provided in slanting maner) .

M/S MAHADEV M PATIL (BID ID -3344191)

M/s. N D KALING (BID ID -3346329)

Sadhana Constructions & suppliers (BID ID -3347018)

M/s B C CHOUGULE (BID ID -3346422)

shree bhavani constructions (BID ID -3347442)

RAJENDRA KRISHNA SARAF (BID ID -3346343)

PURVIK CONSTRUCTIONS (BID ID -3346275)

AARADHYA ENTERPRISES (BID ID -3344788)

DHAIRYASIL RAMAKANT DESAI (BID ID -3347124)