CONSTRUCTION OF PROPOSED TOILET BLOCK IN SPORTS COMPLEX SECTOR 7 CHANDIGARH (COMPOSITE WORK)

DSR Item No. 8.13.7 LED Street light fixture, powder coated pressure die cast aluminum body (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -5 deg to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC As per CISPR 15 , lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED,Driver & electrical circuitary) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K/6500°K(As per ANSI Bin) SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). 25 Watt

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and for all lift.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for : Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works upto plinth level Concrete of M20 grade with minimum cement content of 300 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works above plinth level upto floor V level Concrete of M20 grade with minimum cement content of 300 kg /cum

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Brick work with common burnt clay machine moulded F.P.S. (non modular) bricks of class designation 10 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:(1 cement : 4 coarse sand). Above plinth level upto floor V level

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 3 mm thick ACP Sheet, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement 4 coarse sand) laid and jointed with cement slurry and pointing with white cement sluny admixed with pigment of matching shade including rubbing,curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cheny Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and fixing 15 to 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. (GRANITE).

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. “All above operations to be done in order and as directed and specified by the Engineer-in-Charge”: With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Providing and fixing PVC rain water

pipes pressure rating 6Kg/cm² of size 150mm including specials (cutting ,bends,tee socket,coller etc) complete fixed position . complete in all respect as per direction and to the entire satisfaction of Engineer-in-charge.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body,door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing ISi marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 125x75x4 mm

Providing and fixing ISi marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 75x63x4 mm

Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete 300x16 mm

Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete 250x16 mm

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm

Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 100 mm

Providing and fixing Flamed Granite in 3" thick strips as per pattren on ramp or any where required laid over 20mm thick base cement mortar 1:4 with joints treated with white cement, mixed with matching pigments epoxy touch i/c rubbing, curing, moulding and polishing the edge to give high gloss finish etc. complete in all respects to the entire satisfaction of Engineer in Charge.

S/E of GI pipe bracket of 32mm dia welded with nipple for erection of existing street light fittings to be installed on wall with suitable size of rag bolts and MS clamps made out of 25mmx5mm thick MS flat with all labour and material. The bracket shall be made by GI pipe of 32mm dia (Medium Class) 1 mtr. long with an angle of inclination 105 degree as required. The job includes the cost of petty material required to complete the job to the entire satisfaction of Engineer in Charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., includingwelding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc.,of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and Fixing Soil, Waste and Vent Pipes DSR 17.35: 75 mm diameter :DSR 17.35.2.2

Providing and fixing heel rest sanitary bend DSR 17.40. 100 mm diaDSR 17.40.1

Providing and fixing collar : DSR 17.57. 100 mm DSR 17.57.1.2

75 mm DSR 17.57.2.2

Providing lead caulked joints to sand cast iron/ centrifugally cast (spun) iron pipes and fittings of diameter DSR 17.58 100mm DSR 17.58..1

75mm DSR 17.58.2

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete , including cost of cutting and making good the walls and floors : DSR 17.60 100mm inlet and 75mm outlet DSR 17.60.2.1

Pipes, cables etc, not exceeding 80 mm dia DSR 2.10.1.1

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia DSR 2.10.1.2

Providing and fixing of 4'' HCI P.Trap in complete in all respect

Providing and fixing square-mouth S.W. gully trap grade 'A'’ complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : DSR 19.4 100x100 mm size P type DSR 19.4.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.4.1.1

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 ement : 1 fine sand) including testing of joints etc. complete : DSR 19.1 200 mm diameter DSR 19.1.3

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 ement : 1 fine sand) including testing of joints etc. complete : DSR 19.1 250 mm diameter DSR 19.1.4

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : DSR 19.2 200 mm diameter SW pipe DSR 19.2.3

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : DSR 19.2 250 mm diameter S.W. pipe DSR 19.2.4

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : DSR 19.21 For pipes 100 to 250 mm diameter DSR 19.21.1

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: 19.30. 19.30.3 Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : DSR 19.30.3 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.30.3.1

Extra for depth beyond 45 cm of brick masonry chamber : DSR 19.31 For 600x850 mm size DSR 19.31.3 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.31.3.1

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : DSR 4.1 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) DSR 4.1.3

1:5:10 (1 cement : 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) DSR 4.1.10

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift inc

luding getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. DSR 2.8 All kinds of soil. 2.8.1

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in DSR 6.1 Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.1.1

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 above plinth in:.DSR 6.4 Cement mortar 1:4(1cement :4 coarse sand ) DSR 6.4.1

12 mm cement plaster of mix : DSR 13.4 1:4 (1 cement: 4 coarse sand) DSR 13.4.1

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to15° landings, balconies, shelves,chajjas,lintels,bands, plain window sills,staircases and spiral stair cases up to floor five level,excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1cement : 2coarse sand 4graded stone aggregate 20 mm nominal size).DSR 5.3

Centering and shuttering including strutting, propping etc. and removal of form for :.DSR 5.9 Suspended floors, roofs, landings, balconies and access platform DSR 5.9.3

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level..DSR 5.22 Cold Twisted bar DSR 5.22.6

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall: 15 mm dia nominal bore DSR 18.10.1

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall: 25 mm dia nominal bore DSR 18.10.3

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall: 32 mm dia nominal bore DSR 18.10.4

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall DSR 18.11 :15 mm dia nominal bore DSR 18.11.1

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall DSR 18.11: 20 mm dia nominal bore DSR 18.11.2

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc DSR 18.12 25 mm dia nominal bore DSR 18.12.2

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) DSR 18.17.1 : 25 mm dia nominal bore DSR 18.17.1

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) DSR 18.17.1: 32 mm dia nominal bore DSR 18.17.2

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) DSR 18.17.1: 15 mm dia nominal bore (NSR)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete DSR 18.18: 25 mm dia nominal bore DSR 18.18.2

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : :25mm nominal bore DSR 18.46.2

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : :32mm nominal bore DSR 18.46.3

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. DSR 18.48

Cutting holes up to 30x30 cm in walls including making good the same:DSR 18.76 With common burnt clay F.P.S. (non modular) bricks DSR 18.76.1

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof DSR 18.77

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc DSR 18.78

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved DSR 15.60

Providing and laying of UPVC pipe, IS-4985 marked, Pressure 6 kg/cm2 including cutting, joining, solvent and all necessary fittings complete in all respect except excavation. 100mm

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require DSR 17.7 White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps DSR 17.7.3

Providing and fixing Counter Top Wash Basin with Fixing Accessories,Size: 595 x 420 x 200mm, Shape: Oval X including C.P. Waste complete in all respect. Make as approved by EIC. or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing CP Brass Pressmatic Auto Close type Pillar Cock complete in all respect make Jaquar or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid. DSR 17.3.1

Providing and fixing white vitreous china water closet squatting pan (Indian type) DSR 17.13 Orissa pattern W.C.pan of size 580x440mm DSR 17.13.2

Providing and fixing CP Brass jet with brass nozzal, steel flange and PVC flexible pipe 1/2" approx. 1 m length DSR 17.16A

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete DSR 17.19 10 litre (full flush) capacity-white DSR 17.19.1

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. DSR 17.28 Semi rigid pipe DSR 17.28.1 32 mm dia DSR 17.28.1.1

Providing and fixing uplasticised PVC connection pipe with brass unions: DSR 18.21 45 cm length DSR 18.21.2 15 mm nominal bore DSR 18.21.2.1

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 DSR 18.49 15 mm nominal bore. DSR 18.49.1

Providing and fixing C.P. brass angle valve for basin mixer and geyser points . DSR 18.53 . 15 mm nominal bore. DSR 18.53.1

Providing and fixing of C.P. extension nipple upto 1'' length. DSR 18.53A

Providing and fixing of C.P. Cup heavy duty of approved make

Providing and fixing of Towel Rail 600mm of CP Brass/SS/ABS with screws etc. to the satsifaction of EIC of approved make Kerovit, Cera, Jal and ESSCO

Providing and fixing of Soap Tray made of CP Brass/SS/ABS Plastic including glass bowl of approved make Kerovit, Cera, Jal and ESSCO

Providing and fixing of Towel Ring of CP Brass/SS/ABS with screws etc. to the satsifaction of EIC of approved make Kerovit, Cera, Jal and ESSCO

Providing and fixing of looking glass with PVC beeding 1/4" with plastic hard board or with studs complete in all respect

Providing and fixing white vitreous china flat back half stall urinal of size 420 x 395 x 635 mm with fittings, standard size C.P. brass flush pipe, spreaders and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including pa

inting of fittings and cutting and making good the walls and floors wherever required complete in all respect. Make Cera or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing and fixing of Urinal Partitions curved/rectangular shaped with frosted glass complete in all respect. Make as approved by EIC.

Providing and fixing CP Push cock size 15mm dia complete in all respect complete for Truff

Providing & fixing of 20mm G I Tank Nipple complete in all respect 25mm

Providing & fixing of 20mm G I Tank Nipple complete in all respect 32mm

Providing and fixing 1 mm thick stainless steel grating complete in all respect

Providing and fixing M.S. wire mesh of 1" x1" shed fixed on angle iron 40x40x5 mm including a gate having width 2.5' and height 6'-9'' made angle iron 30x30 x3 mm with same jali and locking arrangement and handle as per site requirement as directed by EIC

Supplying & Fixing of Water Purifier with 3 Stage Purification system consisting of sediment filter, Activated Carbon Filter and Ultravoilet treatment having purification capacity of 200 LPH, water control sensor for automatic control of purifier as per level of water cooler and valve for back flushing of sediment filter complete of make Kent, Usha, Blue Star or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Supplying and Installation of 400 Ltrs Capacity Drinking Water Cooler having (+10%) following specification, full body stainless steel SS 304, ISI marked of approved make Storage Capacity: 400 Ltrs Cooling Capacity: 150 LPH Tank Material: SS 304, Body SS BIS Approval IS 1475 Make Blue Star/Voltas/Climatrol approved by BIS

Providing and fixing of automatic line voltage corrector of 4 KVA ( Step type) for domectic use copper wound complete with volt meter and ampere meter , MCB,Copper binding silicon core with 3step complete with time delay re lays/ controls power coated body of 22 gauge with wire 2.0meter complete in all respects to the entire satisfaction in all respect to th entire satisfaction of the EIC Make Deol, Luminous, V-guard or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Providing, Installing,Testing Commissoing, of mono block pumping 2 H.P set of follwing pare meterincluding starter piping connections & other allied works completein all respect of make Kirlosker/ ABB/ Cromton graves. head 30Mtrs Discharge 1.97LPS RPM2830 or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

Cooler Stand of M/S angle (40 x 40 x 5 up to 1'-6" H.T complete

Supply & erection of Exhaust Fan (heavy duty motor with copper wound metallic body) following size complete with motor, metallic blades, double ball bearing with minimum power consumption, rigid frame with rubber mounting for silent operation, epoxy powder coating along with metallic louver to be installed in the existing opening including cost of making good the damage, Carriage Charges, connection, testing, commissioning etc. as required to complete the job to the entire satisfaction of Engineer-in-charge. Size 12” Sweep 900 RPM with louver of Havells make Turbo Force SP / Orient make Industrial Heavy Duty / Crompton make EXHD 300-6-1/ Bajaj make Supreme PLUS/ Usha make Turbo HDEF only.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m DSR 2.25

Providing and fixing S.S Steel long Bend all fittings complete

Providing and fixing Grab Rail for handicapped toilet 32 mm complete in all respect Jaquar Make or equivalent model of other approved makes in the same range of AOR to the satisfaction of EIC

DSR Item No. 1.29 Supplying and fixing metal box of 150mm X 75mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps piano type switch, connection, painting etc. as required.

DSR Item No. 1.30 Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required.

DSR Item No.2.3 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 6 way Double door

DSR Item No. 2.10 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. :Single pole

DSR Item No. 2.10 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. :Double pole

DSR Item No.1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm

DSR Item No. 1.17 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.: 3 x 1.5 sq. mm

DSR Item No. 1.17 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. :3 x 2.5 sq. mm

DSR Item No. 1.17 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. :3 x 4 sq. mm

DSR Item no. 8.1 LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120lm/Watt) Supplying, installation, Testing & Commissioning of LED Recessed / surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. Syst

em lumen efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) powder coated dia cast/ Extruded aluminium Body including trim. 12 -15 watt