ARC 2026-2028 for Day to Day Maintenance R n R of Furnishing Items Carpentering Items CP n Sanitary Items Plumbing Sewerage Services n Miscellaneous Civil Work at NHAI Residential Building B5 Sec-17 Dwarka ND-110078 other hired buildings in Delhi

Part A

Earth Work and Termite Treatment

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Anti-termite treatment for insecticides using Aqua base spray for pest (for bugs, cockroaches, silverfish, spider, termites, mosquitoes) to walls and ceiling etc. with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying the emulsified chemical @ 0.5 litres per sq.m. by a hand operated pressure pump on wall surfaces, ceiling, electrical fixture,electrical lines including drilling holes inplaces where source of termite is detected squirting chemical solution into the holes and sealing the holes with cement grout. (Rate is per sq.m. of the floor area while actual work will be all walls ceiling, rack, partition and furniture).

Cement Concrete Work

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering

Centering and shuttering including strutting, propping etc. and removal of form work for :

Precasting and placing in position 125 mm dia Bollards 600 mm high of required shape including providing M.S. Pipe Sleeve 50 mm dia 300 mm long in the Bollard and M.S. Pipes 40 mm dia and 450mm long with 150x150x6mm M.S. plate welded at bottom and embedded 150mm in cement concrete 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources), including necessary excavation of size 250x250x450mm deep for the same in bitumen/concrete pavement at specified spacing.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Brickwork and Plastering Work

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

12 mm cement plaster of mix :

Neat cement punning.

Structural Steel Work

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent .

Supplying, fabricating and fixing M.S.Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including, cutting, hoisting, fixing in position and applying two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent , including welding and bolted with special shaped washers etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per specifications and direction of Engineer-in-charge. Hot finished Seamless Type Tubes

Removing old and fixing new concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Flooring and wall cladding work

Providing and laying wooden texture laminated flooring of Scheit (Germany/China) Faus Floor (by Faus Group, Spain), Kaindl (Austria) or equivalent as per manufacturer specification with special sound reduction underlay and PE film as per manufacture specifications. The plank size should be 1210mm-1185mm x 193mm-289mm x 8mm-8.3mm having joint guard joint protection system and patented EIR synchro surface finish. The plank should have glue less click insulation system arrangement. All joints to be filled with click guard joint sealing system for extra joint strength and moisture protection. The floor is to be finished using original skirting and aluminium mouldings of Scheit/Fausfloor / Krono make or equivalent complete as directed by Engineer-in-Charge in approved colour and shade.

Providing and fixing of wall base (skirting)/moulding of required shape 2400mm x 70mm x 15mm including T Profile/reducer of make Scheit (Germany/China) Faus Floor (by Faus Group, Spain), Kaindl (Austria) or equivalent as per direction of Engineer-in-Charge.

Providing and fixing 18mm thick Makrana white second quality Marble stone flooring with 100mm wide udaipur green boarder (sample of marble shall be approved by Engineer-in-charge) over 20mm(average) thick base of cement mortor 1:4 (1cement:4coarse sand) laid and jointed with cement slurry including rubbing and polishing complete .

Providing and fixing 18mm thick Makrana white second quality Marble stone in skirting / dado (sample of marble shall be approved by Engineer-in-charge) over 20mm(average) thick base of cement mortor 1:3 (1cement:3coarse sand) laid and jointed with cement slurry including rubbing and polishing complete .

Providing and laying heavy duty texture vitrified floors tiles in flooring and skirting in different sizes with water absorption's less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigment etc., complete

Providing and laying polished vitrified floors tiles in different sizes with water absorption's less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigment etc., complete

Providing and laying in skirting, risers of steps and dado vitrified tiles, size of tile as shown on drawing / specified of any colour as approved laid on 12mm thick cement mortar1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigment etc. complete.

Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm.

Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS15622( thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dado over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 Kg per sqm. including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 1st quality ceramic glazed floor tiles 300x300 mm ( thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in colours such as white, Ivory, Grey, Fume Red Brown, laid on 20thick cement mortor 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing pre polished Granite flooring in pattern of two or three colours / borders mirror finished 18mm thick over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid over and jointed with white cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished machine cut granite for kitchen platforms, vanity counters, wondow sills, fascias, wall lining and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. complete at all levels.

Extra for providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge.

25mm thick granite stone tread of staircase with bull nose edging and anti skid groove filled with caborandum strip colour.

Kota stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete with base of cement mortar 1:4 (1 Cement: 4 coarse sand):

Providing and laying Kota stone window sill over 20 mm (average) thick base laid over including finishing complete with base of cement mortar 1:4 (1 Cement: 4 coarse sand):

Kota stone slab 25 mm thick in riser and tread of steps, skirting, dado & pillars laid on 12 mm (avg.) thick cement mortar 1:3 (1 cement: 3 coarse sand) & jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing & polishing complete.

Chequrred precast cement concrete tile 22mm thick 250 x 250 mm of approved shade of colour on roofs and gutters and 300 mm high upstand on walls and fillets on 20 mm thick cement mortar 1: 4 ( 1 cement : 4 coarse sand ) including grouting the joints with pigment of matching colour, curing rubbing etc all complete. Dark shade using ordinary cement

Cement plaster skirting (upto 30 cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement :

Removing and refixing existing cladding of Granite/ marble wall clading laid in cement mortar 1:4 (1 cement : 4 coarse sand), including necessary repairs and cement pointing with same mortar complete, including disposal of rubbish to dumping ground, all complete as per direction of Engineer-in-Charge.

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-incharge.

Wood & Aluminum Work

Providing wood work in Frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length

Providing wood work in Shutter of wire mesh doors & windows, and fixed in position with required adhesive and Screws of required dia & length including of all labour and Tools & Plants as per direction of Engineer In-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing of fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading including of applying two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent .

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and polishing with french and melamine polishing matching with door etc. Complete as per direction of Engineer In-Charge. : 2nd class teak wood

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel plating and fixing with necessary screws etc., complete. 35mm/50mm as per direction of Engineer Incharge

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :

Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws.

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 50 mm

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 /450/300 mm long with screws etc. complete as per directions of Engineer- in-charge.

Providing and fixing powder coated telescopic drawer channels 500 /450/300mm long with necessary screws etc. complete as per directions of Engineer- in-charge.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing glazing in aluminium/ Wooden door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Including Cost of aluminium/ Wooden snap beading):

Water Supply Work

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. Concealed work, including cutting chases and making good the wall etc.

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with trenching, refilling and testing of joints complete as per direction of the engineer in charge. External work

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE Composite Pressure Pipes Socket

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE Composite Pressure Pipes Elbows

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE Composite Pressure Pipes Tee

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE Composite Pressure Pipes Gate Valves

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

Providing and fixing G.I. Union/ CPVC Union in G.I. pipe/ CPVC pipe including cutting and threading the pipe and making long screws etc. complete

Providing and fixing uplasticised PVC connection pipe with brass unions :

Providing and fixing ball valve (brass) of approved quality, High or low pressure, complete :

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)

Sanitary Work

Providing & fixing White vitreous china water closet squatting pan (Indian type) along with "S" or "P" trap, 10 litre low level white P.V.C. flushing cistern, flush pipe, including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. White Vitreous china W.C Pan of size 580x440 mm

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device conforming to IS : 7231, with all fittings and fixtures complete.

Painting and Polishing Work

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Note: Measurement Will be 30% of plastic emulsion paint and OBD for Old Work

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :Old work (One or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with textured paint of required shade : Old work (One or more coats) applied @ 1.82 ltr/10 sqm..

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On concrete work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Note: New Work

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Finishing walls with water proofing cement paint of required shade :

French spirit polishing :One or more coats on old work

Melamine polishing on wood work (one or more coat).

French spirit polishing :Two or more coats on new works including a coat of wood filler

Providing and applying 2.5 mm thick X 100 mm Width road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications

Water Proofing work

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth (wt. not less than 50 GSM) when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured.

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Roofing & Shading Work

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-incharge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.

False Ceiling Work

Providing & fixing in position at all heights suspended false-ceiling system using 595 mm x 595 mm Calcium Silicate Ceiling Tiles having 15 mm Densified edges and 100% humidity resistance. Incombustible as per BS 476 Part IV with thermal conductivity of 0.043 w/m degree KC and approved surface design Spintone and edge profile Tegular placed in a suspended grid of size 600 mm x 600 mm made from hot dipped G.I. steel sections having an exposed surface capping of pre-finished baked polyester painted coil, wherein the main tee of size 24 mm x 38 mm x 0.33 mm x 3600 mm shall be suspended at 1200 mm centers along length of ceiling with 4 mm dia GI wire with necessary level adjusters and cross tees of size 24mmx30mmx0.33mmx1200 mm shall be inserted into slots between the main tees at 600 mm c/c and thereafter in direction vertical to the longer cross tees, cross tees of size 24 mm x 30 mmx0.33 m mx600 mm shall be inserted so as to form a gird of size 600 x 600 mm resting on the periphery on wall angles of size 22.2mm x 22.2 mm x 0.45 mm. Necessary openings for light fixtures diffusers etc are to be made as per drawings and directions of Engineer incharge, complete.

Rainwater Work & Fittings

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler

Single tee with door

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Repairs to Building

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineerin- Charge.

Taking out existing CC interlocking paver blocks, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in- Charge.

Laying existing cement cocrete interlocking paver blocks or providing & laying new interlocking paver blocks in case of damaged old block of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing Chrome finished brass curtain rods of wall thickness 1.25 mm with two chrome finished brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete.

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete

Providing and fixing bright finished brass helical door spring (superior quality).

Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-incharge.

Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line of required dia.

Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Removing and fixing new fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading including of applying two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent .

Providing and fixing glazing in aluminium door,window,ventilators, shutters & partitions etc. with neoprene gasket etc. complete as per the architectral drawings and the direction of engineer-in-charge. - With float glass panes of 5.5mm thick

Structural Protection Work

Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge

Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.

Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.

Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2

Dismantle and Disposal

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Dismantling W.C. of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge.

Dismantling 15 to 40 mm dia GI/PPR/CPVC pipe (Concealed or exposed on wall) including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Dismantling work of tiles, granite, marble, stone etc in floors, skirting and walls laid in cement mortar including disposal. For thickness 10 mm to 25 mm

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, including all lifts involved.

Manpower

Supply of Manpower:

Part A Amount including GST

Part B

Miscellaneous Items

Providing and fixing mirror polished machine cut granite stone for wall lining upto 10 m height in cement mortar 1:3 (1 cement: 3 coarse sand) 12mm thick jointed with grey cement slurry (@ 3.3 Kg/ sqm including pointing with white cement mixed with pigment epoxy touch ups including rubbing, curing etc. complete at all level.

Providing and fixing built-in-cup board comprising door shutter of 19mm thick made of commercial plywood IS : 12077 marked (Duro, Century, Green, Novapan) including 1.0mm thick lamintes on shutter, IInd class teak wood lipping of 19mm wide x 10mm thick size, moulding 20wide x12mm thick and back side 6mm thick commercial ply, sides and partition with 19mm commercial plywood, drawers with 19mm commercial plywood with necessary screws, channel and black enamelled piano hinges and all brass fittings complete as per direction of the Engineer-in-Charge. (As per existing design and pattern)

Providing and fixing kitchen cabinet above and below counter with door shutter of 19mm thick made of commercial plywood IS : 12077 marked (Duro, Century, Green, Novapan) having one side decorative laminates sheet (1.0m thick) of approved shades including IInd class teak wood lipping of 19mm wide x 10mm thick size, moulding of 20mm wide x 12mm thick and back side 6mm thick commercial ply, sides of cabinet with drawers commercial plywood with necessary screws, channels, handles and black enamelled M.S. butt hinges and all brass fittings complete as per direction of the Engineer-in-Charge. (As per existing design and pattern)

Providing and fixing Modular kitchen for a kitchen having plan dimension of 2.885m x 2.10m in Block - A having U - shape kitchen plateform with, stainless steel baskets, granite on counter top and accessories such as hinges, Sliding channel, Locking bolts, screws etc complete as per direction of the Engineer-in-Charge. (As per existing design and pattern). Frame / partions made of 19mm laminated commercial ply IS : 12077 marked (Duro, Century, Green, Novapan) or powder coated CRCA sheet and shutter made of laminated commercial ply IS : 12077 marked (Duro, Century, Green, Novapan).

Providing and fixing Modular kitchen for a kitchen having plan dimension of 2.90m x 2.135m in Block - A having L - shape kitchen plateform with, stainless steel baskets, granite on counter top and accessories such as hinges, Sliding channel, Locking bolts, screws etc complete as per direction of the Engineer-in-Charge. (As per existing design and pattern). Frame / partions made of 19mm laminated commercial ply IS : 12077 marked (Duro, Century, Green, Novapan) or powder coated CRCA sheet and shutter made of laminated commercial ply IS : 12077 marked (Duro, Century, Green, Novapan)

Providing and fixing Modular kitchen for a kitchen having plan dimension of 3.255m x 3.145m in Block - A having L -shape kitchen plateform with, stainless steel baskets, granite on counter top and accessories such as hinges, Sliding channel, Locking bolts, screws etc complete as per direction of the Engineer-in-Charge. (As per existing design and pattern). Frame / partions made of 19mm laminated commercial ply IS : 12077 marked (Duro, Century, Green, Novapan) or powder coated CRCA sheet and shutter made of laminated commercial ply IS : 12077 marked (Duro, Century, Green, Novapan).

Providing and fixing Modular kitchen for a kitchen having plan dimension of 3.485m x 2.365m in Block - A having U - shape kitchen plateform with sink & drain board, stainless steel basket,cooking hood, five burner hobes & cooktop, granite on counter top and accessories such as hinges, Sliding channel, Locking bolts, screws etc complete as per direction of the Engineer-in-Charge. (As per existing design and pattern). Frame / partions made of 19mm laminated commercial ply IS : 12077 marked (Duro, Century, Green, Novapan) or powder coated CRCA sheet and shutter made of laminated commercial ply IS : 12077 marked (Duro, Century, Green, Novapan)

Providing and fixing marine plywood for cupboard shutter of approved quality ( century/ kitply/ greenlam or it equivalent) confirming to IS: 710 including cutting into required size, jointing with nails adhesive, P/F 4mm thick second class teak wood beading on its edges with nails and adhesive etc. complete as directed by the EIC.

Providing and fixing Steel Name Plate of approved quality and required size, fabricated from 1.5 mm thick stainless steel sheet (Grade 304) or as specified, with engraving/etching/laser-cutting of alphabets, numerals, logos, or other inscriptions in bilingual language (English & Hindi) as approved. The plate shall be fixed on wall, column, gate, or other surface with stainless steel screws, studs, adhesive, or suitable fixing arrangement complete. The item includes cost of steel plate, engraving/etching work, polishing, protective coating, fixing accessories, transportation, labour, T&P, all materials and incidental charges complete as per the direction of Engineer-in-Charge

Providing and fixing Emergency Exit / Fire Safety / Directional / Warning / Informational Sign Board of approved design, shape, size and material, including lettering, symbols, arrows, pictograms and messages in bilingual language (English & Hindi) as approved. The sign board shall be prepared with suitable printing, painting, vinyl pasting, reflective or photoluminescent finish as specified and fixed at the required location with screws, clamps, adhesive, brackets or other approved fixing arrangement complete. The item includes cost of all materials, fabrication, lettering, fixing accessories, transportation, labour, T&P and all incidental charges complete as per the direction of Engineer-in-Charge.

Taking out existing MS door shutter, repair by cutting, Welding, repair of punctured wire mesh, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws/ welding, etc. as required, all complete as per the direction of the Engineer-in-charge.

Providing and Fixing ofGodrej Mortise Door Lock Handle Set | 175mm Venus | 6-Lever Locking Mechanism | Reversible Latchbolt | Suitable for Left & Right Handed Doors (Brass Finish) , Item Weight not less than 480 Grams which include: 1n lock, 1n striker plate, 1n handle set, 1n square shank, 2n keys, tools & labours all complete as per direction of Engineer In-Charge

Providing and Fixing of Godrej C0712 Speed Hydraulic 60kg Door Closer, Maximum Closing Moment: 14Nm ; Other Dimensions: Door Weight : 60 kg, Door Panel Width : 1000 mm, Door Opening Angle : 180°,Warranty: 1 Year warranty from the date of invoice Material: Stainless Steel,Item Weight ‏ not less than‎ 1 kg 370 g, tools & labours,all complete as per direction of Engineer In-Charge

Supply of Stainless Steel Corner L Angle Bracket (L-Patti) (Set of 8 pcs.)

Supply of Iron Door Chapka Kunda, Thickness: 2.6 - 3 mm X 100 mm

Supply of Hettich Onsys 4447i Soft Close Hinges for up to 25mm Thick Door 0 Crank (2pcs.) (L-Bihari Kabja)

Supply of Hettich Onsys 4447i Soft Close Hinges for up to 25mm Thick Door 8/16 Crank (2pcs.) (L-Bihari Kabja)

Supply of Godrej Supernova Pin Cylinder Wardrobe Lock, Steel Nickel Plated Lock Wooden Cabinets.

Supply of Harrison H-0609_PK2 38mm Iron 6 Lever Dead Mini Super Lock Set with 2 Keys Used for Aluminium Doors

Supply of Casement Window Hinge, Concealed Hinge, 10-Inch, Stainless (Pack of 2 Hinges) for Aluminium Windows

Supply of Door Seal Bottom, Air Gap Rubber Shield, 4 Feets, Anti Rust for Aluminium Doors (Pack of 2)

Supply of Cabinet Handle Pull Stainless Steel Brushed Nickel with Screw for All Types Wooden & Furniture Doors (10 Inch, Silver Finish) - (Pack of 2)

Supply of Door Catcher/Door Magnet for Cabinet Cupboard Wardrobe (Pack of 5 Pcs.)

Supply of Godrej 4 Lever Locking Mechanism Hook Bolt for Aluminum Doors, Suitable for Left & Right, Steel Finish (Silver), Low Carbon Steel Set includes - Lock - 1 Unit, Striker plate - 1 Unit, Rose - 2 Unit, Keys - 2 Unit, Screws packet - 1 Unit, Fitting instruction slip and marker - 1 Unit

Renewing iron or M.S. Wheel or roller of steel / aluminum sliding door or gate and fitting and fixing the same with necessary clamps, nuts and bolts/welding and erection etc. complete.

Supply of 110mm (4.3 inch) Mild Steel Pelmet Patti Strip Set for Hanging Wooden Item (Pack of 2 Pcs.)

Supply of Anchor Fasteners,Size 6 mm, (Pack of 12 Pcs)

Supply of Stainless Steel Door and Window Handle - Diagonally Shaded - 6 Inch (Pack of 12 Pcs)

Supply of 10 Inches Stainless Steel Main Door Handle/Door Pull Handle, Satin Silver Finish

Supply of 4 Inches Stainless Steel Main Door Handle/Door Pull Handle, Satin Silver Finish

Supply of Door Stopper Rubber for Main Door Or Door Silencer Wall Protector Size- 2 Inch, (Pack of 5 Pcs) with Screw

Supply of Metal Solid Curtain Rod Bracket Finials

Supply of Metal Solid Curtain Rod Bracket J-Hooks

Supply of Miscellaneous Water Supply Materials

Supply of Aluminum Square Ventilation Louver, Size: 2 X 2 Feet

Removing and refixing new aluminium snap beading for broken glazed aluminium doors/ Windows all including material and labour etc complete.

Removing and refixing new EPDM rubber / neoprene gasket for broken glazed aluminium doors/ Windows all including material and labour etc complete.

Providing and fixing white glazed vitreous China wall mounted European type water closet with seat and lid, C.P. brass hinges and rubber buffers, CP flush valves of an approved design, including cutting and making good the walls and floors where required.

Providing and fixing white glazed vitreous European type water closet with seat and lid, C.P. brass hinges and rubber buffers, vitreous china flushing cistern with fittings, brackets, overflow pipe with mosquito proof coupling of an approved design, including cutting and making good the walls and floors where required.

Providing and fixing white glazed vitreous china wash basins with , C.P. brass waste 32mm C.P. bottle trap and unions and sealing of joints between wash basins and counter slabs around the wash basins with Silicone rubber cement of approved make of matching colour all complete including cutting and making good the walls and floors where required.

Providing and fixing acrylic bath tub HINDWARE Cat. NO. 500505/ PARRYWARE Cat.no.C8752/ CERA Cat.no.8001 size 1670X760X400 mm with matching panel including 32mm dia over flow and 40mm dia POP up waste assembly. 40mm dia cast brass 'P' trap with cast brass adapter to suit waste assembly, setting the tub in wall chase, cutting and making the walls and floor all complete or as approved by the Engineer-in-Charge.

Providing and fixing C.P. brass bib taps long body (Jaquar Cat NO. KUP-SSF-35037PM or as approved by the Engineer-in-Charge) including cutting and making good the walls wherever required.

Providing and fixing C.P. brass Two Way Bib Tap - Chrome long body (Jaquar Cat NO. OPP-CHR-15041PM or as approved by the Engineer-in-Charge) including cutting and making good the walls wherever required.

Providing and fixing hand shower (Health Faucet) with 6mm dia. with 1 Meter Long PVC Tube & Wall Hook all complete Jaquar cat no. ALD-CHR-563 or as approved by the Engineer-in-Charge.

Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 8mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 6mm copper backed float glass mirror of approved make with and including 8mm thick BWP type ply board, 40mm stainless steel channel plugged to wall, hard wood treated with two coats of wood preservative, etc. all complete as per specifications.

Providing and fixing C.P. brass twin robe hooks, JAQUAR Cat. No. 1161 / Parko cat. No. 1582 / Kingston cat. No. KRI - 29 or as approved by the Engineer-in-Charge.

Providing and fixing liquid soap dispenser make Jaquar Cat No.: ACN-CHR-1135N or as approved by the Engineer-in-Charge.

Providing and fixing 15mm C.P. brass angle valve (Jaquar Cat No. FUS-CHR-29053 or as approved by the Engineer-in-Charge) including cutting and making good the walls wherever required.

Providing and fixing C.P brass Single Towel Rail 600mm Long - Chrome (JAQUAR Cat. No. ACN-CHR-1111SM or as approved by the Engineer-in-Charge) complete with C.P. brass brackets fixed to rawl plug of approved design with C.P. brass screws.

Providing and fixing CP brass Towel Rack 600mm Long - Chrome (JAQUAR Cat. No.ACN-CHR-1181FS or as approved by the Engineer-in-Charge) complete with CP brass brackets fixed to rawl plug of approved design with CP brass screws.

Providing and fixing CP brass Towel Ring Square with Round Flange (JAQUAR Cat. No. ACN-CHR-1121N or as approved by the Engineer-in-Charge) fixed to rawl plug of approved design with CP brass screws.

Providing and fixingOverhead Shower 140mm Round Shape Multi Flow (Rain & Massage) with Air Effect (ABS Body & Face Plate Chrome Plated) with Rubit Cleaning System Jaquar Cat No. OHS-CHR-1769 or as approved by the Engineer-in-Charge.

Providing and fixing Shower Arm Casted 190mm Long Flat Shape for Wall Mounted Showers with Flange Jaquar Cat No. SHA-CHR-483 or as approved by the Engineer-in-Charge.

Providing and fixing Overhead Shower 150X150mm Square Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System Jaquar Cat No. OHS-CHR-35495 or as approved by the Engineer-in-Charge.

Providing and fixing CP brass concealed stop cock reduced body Jaquar Cat No ALD-CHR-089 or as approved by the Engineer-in-Charge.

Providing and fixing single lever concealed divertor for bath and shower system Jaquar Cat NO. 15075 / Parko cat. no. 21003 / Kingston cat. no. KRA 004 shower or as approved by the Engineer-in-Charge.

Providing and fixing CP bath spout Jaquar Cat. No. 429 /PARK Cat.no.21006/KINGSTON Cat.no.KRA 015 or as approved by the Engineer-in-Charge

Providing and fixing Bath tub spout with button attachment JAQUAR Cat. No.SPJ-CHR-463PM or as approved by the Engineer-in-Charge

Providing and fixing telephonic shower JAQUAR Cat. No. 557 Parko cat. no. 2173 / Kingston cat. no. KRA 012 or as approved by the Engineer-in-Charge

Providing and fixing CP mixer Jaquar cat. No. OPP-CHR-15011BPM or as approved by the Engineer-in-Charge.

Providing and fixing CP pillar tap Jaquar Cat. No. OPP-CHR-15001PM or as approved by the Engineer-in-Charge.

Providing and fixing CP bib tap Jaquar Cat. No. CQT-CHR-23037 or as approved by the Engineer-in-Charge.

Providing and fixing white glazed vitreous European type water closet lid for Hindware make ARMADA Cat. No. 91009 / Parryware cat. No. C 8470/Cera cat. No. 1043 or as approved by the Engineer-in-Charge.

Providing and fixing CP brass Sink Mixer with Regular Swinging Spout (Wall Mounted Model) with Connecting Legs & Wall Flanges model Jaquar Cat. NO. FLP-CHR-5309PM or as approved by the Engineer-in-Charge

Providing Flush Tank Syphon Kit Full Set, Flushing Cistern Accessories, Standard Size Hindware, CERA or equivalent as per direction of Engineer In-Charge

Providing Wall Concealed Flush Tank Syphon Kit Full Set, Flushing Cistern Accessories, Standard Size Hindware, CERA or equivalent as per direction of Engineer In-Charge

Providing and Fixing High Speed 400mm Wall Fan of approved make Havells, Crompton, Orpat or equivalent only as per direction of Engineer In-Charge.

SITC of Orient Electric Titan 100L Desert Air Cooler, 4-Way Cooling, Ice Chamber, Inverter Compatible, High Air Delivery, Metal Blades, Honeycomb Pads, 1 Year Warranty Mounting Type: Freestanding Additional Features: Auto Fill, Auto Restart Air Flow Capacity: 400 Cubic Feet Per Minute Controls Type: Knob Reservoir Capacity: 125 Liters Form Factor: Desert Wattage: 210 Watts Number Of Speeds 3 Operation Mode Manual

Supply of Crompton Insta Comfy 800 Watt Room Heater with 2 Heat Settings

Supply of Artificial Grass PVC Plastic Durable Stick Turf Mat of required shape and size including transportation, unpacking, labour all complete of approved make or as per direction of Engineer In-Charge

Providing and fixing of Transparent or Sun Control films on Glass of Window/Doors or Partition of cabin all inclusive of material and labour all complete as per direction of Engineer In-Charge

Providing and fixing Kitchen stainless steel kitchen sink, pressedmsingle bowl single drain board 32" X 20" X 8" Matt Finished of Make Hindware Platino or as approved by the Engineer-in-Charge

SITC of RO PLANT Commercial (RO+UV+TDS+AUTO SHUT OFF) water purifier 100 Liter Per Hour Stainless steel Full Automatic with TDS Adjuster Includes: 1. Fully Stainless Steel Body With Two 300 GPD High Performance Copper Winded Booster Pump 2. Purification Technology : RO : Type : Electrical, Purification Stage :Stage 1: 5 microns inline PP filter || Stage 2: Granule Active Carbon Filter ||Stage 3: Block Active Carbon Filter || Stage 4: RO Membrane ||Stage 5: Post Carbon Filter 3.Purification : 100 Liter Per Hour , Two 300 Gpd Booster Pump , One Activated Carbon Filter, UV Purification system 4.1 Year Warranty on Booster Pump And SMPS

SITC of Blue Star 80 L Storage Water Cooler SDLX6080B Features: Brand Name :Blue Star Refrigerant :R 134 a Capacity : 80 L Type of Product :Water Cooler Model No :SDLX6080B Cooling Capacity: 60 Litre per Hour Energy Consumption Rating: 5 Stars

SITC of OGeneral CHAA Series 1.8 Ton 5 Star Inverter Window AC Features: Brand:O-General Model:‎AXGB22CHAA-B Capacity:1.8 Tons Annual Energy Consumption:1250 Kilowatt Hours Per Year Energy Consumption Rating: 5 Stars Noise Level:54 dB Installation Type:‎Window Included Components:1 AC unit, 1 Remote Control, 1 User manual. All Included charges of material, labour and transportation.

SITC of Carrier 2 Ton 5 Star AI Flexicool Inverter Split AC Features: Brand:Carrier Model:‎‎224050090540@CMI Capacity:2 Tons Annual Energy Consumption:‎920.55 Kilowatt Hours Per Yearr Energy Consumption Rating: 5 Stars Noise Level:38 dB Installation Type:‎Split AC Included Components:1 AC unit, 1 Remote Control, 1 User manual, required copper pipes and wires. All Included charges of material, labour and transportation.

SITC of V-Guard 15 litres Storage Vertical Wall Mounted Water Geyser (White) Corded Electric, Maximum Pressure 8.00 bars, including of transportation, installation, T&P all complete as per direction of Engineer In-Charge.

SITC of Racold CDR DLX Plus 25Llitres Storage Horizontal Wall Mounted Water Geyser (White) Corded Electric, Temperature Display & Knob, Fits Under False Ceilings, Titanium Enameled Coating,Wattage 2 KW, Maximum Pressure 8.00 bars, including of transportation, installation, T&P all complete as per direction of Engineer In-Charge.

SITC of Racold CDR DLX Plus 35Llitres Storage Horizontal Wall Mounted Water Geyser (White) Corded Electric, Temperature Display & Knob, Fits Under False Ceilings, Titanium Enameled Coating,Wattage 2 KW, Maximum Pressure 8.00 bars, including of transportation, installation, T&P all complete as per direction of Engineer In-Charge.

Providing and Fixing Electric Kitchen Chimney, Pyramid Shape SS Baffle filters 60cm 1100 m³/h of approved make Glen, Kaff or equivalent only as per direction of Engineer In-Charge.

Supplying of Crompton DMB30 3 HP Single Phase Heavy Duty Domestic Monoblock Pump Phase: Single Phase Model No: DMB30 Frequency: 50-60 Hz Discharge Range: 11700-960 lph Power: 3 HP Speed: 1500 RPM Head (m): 9 - 45 m Suc x Del (mm): 40 x 40 mm Warranty Duration (Months): 12 months Flow Rate: 11700-960 LPH material supplied should be in sealed container and open in front of authority engineer. The contractor must supply the material mentioned above only, no other equivalent material will accept.

Supplying of Crompton DMB10DGL(3PH) 1 HP Domestic Monoblock Pump Phase: Three Phase Model No: DMB10DGL(3PH) Voltage: 300-440 V Frequency: 50 Hz Impeller Material: Brass Power: 1 HP Speed: 1500 RPM Operating Temperature: Suitable for 65 degree Celsius Water Suc x Del (mm): 25x25 mm Head: 18-45 m Warranty Duration (Months): 12 months Flow Rate: 2800-880 LPH Seal: Mechanical Seal Motor Body: Cast Iron material supplied should be in sealed container and open in front of authority engineer. The contractor must supply the material mentioned above only, no other equivalent material will accept.

Supplying of Anchor by Panasonic 4 way 6A International Socket with Single Switch | 4 Way Extension Board with 4 Mtr Extension Cord | Multi Plug Socket material supplied should be in sealed container and open in front of authority engineer. The contractor must supply the material mentioned above only, no other equivalent material will accept.

Supplying of Taurus C100 Lite Executive Office Chair (Mid Back Chair) Features: Chrome Metal Wheelbase Heavy nylon made Backrest Sonic Fixed Arm-rests Lumbar Pad in backrest is adjustable upward and downward Gas Lift: Class 4 Hydraulic Tilt Mechanism adjust backrest upto 120 Degrees Weight Capacity : Up to 105 Kgs Suitable for Height: 5.2" to 6.0 ft material supplied should be in sealed container and open in front of authority engineer. The contractor must supply the material mentioned above only, no other equivalent material will accept.

Supplying of Exclusive Furniture VCHGTB01 Metal Visitor Chair Blue material supplied should be in sealed container and open in front of authority engineer. The contractor must supply the material mentioned above only, no other equivalent material will accept.

Supply of powdered coated coloured planter made of stainless steel, non breakable with modern outlook and scratch proof coating having a protective ring at the base which prevents damage to the floor & water proof edges of required size including transportation, unpacking, labour all complete of approved make or as per direction of Engineer In-Charge:

Supply of Stainless Steel Ashcan Bin / Pushcan Bin/ Waste basket for dry waste like papers and office waste etc, having a protective ring at the base which prevents damage to the floor & fingerprint-proof finish with dent resistant heavy guage stainless steel of required size including transportation, unpacking, labour all complete of approved make or as per direction of Engineer In-Charge:

Part B Amount including GST

Total Amount (Part A + B) including GST

Abstract of Amount

Tentative Estimated Rates for Internal Painting of Existing Towers & Flats and miscellaneous civil works at NHAI Residential Enclave, Pocket:B-5, Sector-17, Dwarka, New Delhi-110078. -FINANCIAL BID

Agreement No.

Name of Agency

Date of Start

Date of Start (Actual)

Date of Completion

Date of Abstract

Item no.

For Repairing and Painting

White washing with lime to give an even shade : Old work (one or more coats)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : Old work (one or more coats) over and including water thinnable priming coat with cement primer

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Finishing walls with textured interior paint of required shade : Old work (One or more coats) applied @ 1.82 ltr/10 sqm.

Finishing with Epoxy paint (one or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. Old work

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Where required only

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Where required only 30% of item no. 1.7

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Repair to plaster of thickness 12mm to 20 mm in patches, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge.

Dismantling work in floors, skirting and walls laid in cement mortar including disposal. For thickness of tiles 10 mm to 25 mm

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of required size

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of Required size

Dismantling 15 to 40 mm dia pipe including stacking of dismantled pipes as per direction of Engineer-in-Charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

Providing and fixing shower set comprising one CP single lever concealed diverter JAQUAR Cat. No. 15075 / Parko cat. no.21003 / Kingston cat. no. KRA 004 .Bath tub spout with button attachment JAQUAR Cat. No. 463 / Parko cat. no. 21006A / Kingston cat. no. KRA-010 . shower with shower arm JAQUAR Cat. No. 477 & 489 / Parko cat. no. 2174 / Kingston cat. no. KRA 011. and telephonic shower JAQUAR Cat. No. 557 Parko cat. no. 2173 / Kingston cat. no. KRA 012 or as approved by the Engineer-in-Charge.

Providing and fixing shower enclosure HINDWARE Cat.no.506200/ PARRYWARE Cat .no.C8474/ CERA Cat.no.8831.overall size (H X L X W) 200 X 900 X 900mm finished with 6mm tempered clear glass complete with popup waste, door, SS door handle magnetic seal and shower panel HINDWARE Cat. no.500900/ PARRYWARE Cat.no.C841U/CERA Cat.no.8918. over all size (H x W) 1650 x 280mm finish with ABS body carring and making good the walls and floor all complete or as approved by the Engineer-in-Charge.

Providing and fixing C.P. brass bib taps long body (Jaquar Cat NO. 107 / Parko cat. No. 2106 / Kingston cat. No. KRA013 or as approved by the Engineer-in-Charge) including cutting and making good the walls wherever required. 15mm dia

Providing and fixing C.P. brass two way bib taps long body (Jaquar Cat NO. 15041 / Parko cat. No. 2106B / Kingston cat. No. KRA 013A or as approved by the Engineer-in-Charge) including cutting and making good the walls wherever required. 15mm dia

Providing and fixing 15mm C.P. brass angle valve with C.P. brass connection pipe (Jaquar Cat No. 053 & Cat No. 803 / Parko cat. no. 2119A/ Kingston cat. no. KRA 014 or as approved by the Engineer-in-Charge) union nuts complete with C.P. brass flange including cutting and making good the walls wherever required.

Providing and fixing CP brass shower with revolving ball joint Jaquar Cat No. 493 with shower arm Jaquar Cat No. 483 Parko cat. No. 2174 / Kingston cat. No. KRA011 or as approved by the Engineer-in-Charge.

Providing and fixing CP brass concealed stop cock reduced body Jaquar Cat No. 089 / Parko cat. No. 2117 / Kingston cat. No. AGR 306 or as approved by the Engineer-in-Charge.

Providing and fixing bath and shower arrangement comprising single lever concealed divertor for bath and shower system Jaquar Cat NO. 15075 / Parko cat. no. 21003 / Kingston cat. no. KRA 004 shower with shower arm Jaquar Cat No. 493 & 483 / Parko cat. no. 2174 / Kingston cat. no. KRA 011 with CP bath spout Jaquar Cat. No. 429 /PARK Cat.no.21006/KINGSTON Cat.no.KRA 015 or as approved by the Engineer-in-Charge.

Providing and Fixing CP brass single lever sink mixer with swinging spout wall mounted model (Jaquar Cat. NO. 15163 / Parko cat.no.21004/Kingston cat. no. KRA005 as approved by the Engineer-in- Charge).

Providing and fixing S.S. hinged grating, 6mm thick with frame as approved by the Engineer-in-Charge) including setting in floor with cement mortar 1:3.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible (coil shaped) PVC waste pipe for sink and wash basin 32 mm dia or 40 mm dia with length not less than 700 mm i/c PVC waste

Flexible pipe

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing gully trap P type 100x100 mm

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material as per direction of Engineer-in-charge.

In cement mortar

Qty. BF./CMB /P-

Total=

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 12.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and laying at site 12mm thick wooden laminated floor (AC'5) having an inbuilt 2mm compact sound bloc™ backing-class of use 32/23, wear resistance, impact resistance-IC 2, (as per EN 13329), Top surface having a MLC (Multi-Layer Composite) highly developed laminate, top surface treated with (Aluminium oxide) titan X™ on top of high density fiberboard substrate (density 910 kg/cum) specially developed core: having patented click system perfect fold™ joints to secure long lasting joint. The planks shall be placed on an under lay of 0.2mm thick alkali resistant polyethylene sheet. All as per manufacturer specification.

Providing and fixing at site 10mm to 12mm thick 100mm high laminated wooden skirting/trim all complete as engineer in charge.

For rain water and drainage

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

(i) Single socketed pipes

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion.

Shoe (Plain)

160mm Shoe

110mm Shoe

Single tee with door

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50 x 50 x 50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing Slotted cowl (terminal guard)

110 mm dia

160 mm dia

For Wooden Finishing

French spirit polishing : One or more coats on old work

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Melamine polishing on wood work One or more coats on old work

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Wire Mesh Doors

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length inclusive of all complete as per direction of Engineer In-Charge.

Qty. BF./CMB /P-

Total=

Providing wood work in Shutter of doors, windows, and fixed in position with required adhesive and Screws of required dia & length including of all labour and Tools & Plants as per direction of Engineer In-Charge.

Qty. BF./CMB /P-

Total=

Providing and fixing of fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading including of applying two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent .

Qty. BF./CMB /P-

Total=

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and polishing with french and melamine polishing matching with door etc. Complete as per direction of Engineer In-Charge. : 2nd class teak wood

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete :

Qty. BF./CMB /P-

Total=

French spirit polishing : Two or more coats on new works including a coat of wood filler

Qty. BF./CMB /P-

Total=

Melamine polishing on wood work (one or more coat).

Qty. BF./CMB /P-

Total=

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.

Qty. BF./CMB /P-

Total=

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Qty. BF./CMB /P-

Total=

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

Total=

Below 36.14%=

Total=

Qty. BF./CMB /P-

Total=

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Size of Tile 600x600 mm

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Qty. BF./CMB /P-

Qty. BF./CMB /P-

Total=

Extra Item Total=

Total=

RECOVERIES

2.5 % security deposit

Income Tax @ 2% on

GST @ 2% on

1% Labour cess on

1% Water Charges on

TOTAL

Gross amount

Less Recovery

Net Payable

Certified that :-

The work has been carried out as per CPWD specification & direction of Engineer-in-charge.

No labour complaint has been received till date with this office.

All necesarry recoveries have been made in this bill.

No T&P has been issued to the contractor.

No QCTA/CTE observations are pending.

Mandatory test sample has been sent, test awaited.

The contractor has engaged its Engineer on site of work.

Date of Measurement:

For Repairing and Painting

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Where required only

Master Room

Deductions Door / window

Less Cupboard area

Guest Room

Deductions Door / window

Less Cupboard area

G/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

CMB- /Page-

Date of Measurement:

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Where required only 30% of item no. 1.7

Master Room

Deductions Door / window

Less Cupboard area

Guest Room

Deductions Door / window

Less Cupboard area

G/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

Total =

CMB- /Page-

Date of Measurement:

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Master Room

Deductions Door / window

Less Cupboard area

Guest Room

Deductions Door / window

Less Cupboard area

G/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

CMB- /Page-

Date of Measurement:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

for 1st and 2nd floor

Kitchen

CMB- /Page-

Date of Measurement:

Melamine polishing on wood work One or more coats on old work

Master Room

Guest Room

G/R Passage

Living / Dining

CMB- /Page-

Date of Measurement:

For Wooden Finishing

French spirit polishing : One or more coats on old work

Master Room

Guest Room

G/R Passage

Living / Dining

CMB- /Page-

Date of Measurement:

For Repairing and Painting

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Where required only

Children Room

above cupboard

Deductions Door / window

Less Cupboard area

Bed Room

Deductions Door / window

Less Cupboard area

B/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

CMB- /Page-

Date of Measurement:

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Where required only 30% of item no. 1.7

Children Room

above cupboard

Deductions Door / window

Less Cupboard area

Bed Room

Deductions Door / window

Less Cupboard area

B/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

Total =

CMB- /Page-

Date of Measurement:

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Children Room

above cupboard

Deductions Door / window

Less Cupboard area

Bed Room

Deductions Door / window

Less Cupboard area

B/R Passage

Deductions Door / window

Opening

Opening

Kitchen

Living / Dining

Deductions Door / window

add jamb

add jamb

opening

CMB- /Page-

Date of Measurement:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

From 3rd to 8th floor

Kitchen

CMB- /Page-

Date of Measurement:

Melamine polishing on wood work One or more coats on old work

Master Room

Guest Room

G/R Passage

Living / Dining

CMB- /Page-

Date of Measurement:

For Wooden Finishing

French spirit polishing : One or more coats on old work

Master Room

Guest Room

G/R Passage

Living / Dining

CMB- /Page-

Date of Measurement:

Flat No. A 501

For Repairing and Painting

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Where required only

Flat No. A 501

MBR Ceiling

l/open

lobby ceiling

L/door

Dining area, ceiling

L/open

Ceiling

ceiling

Kitchen, ceiling

L/open

Entry ceiling

L/open

Room-2 , ceiling

CMB- /Page-

Date of Measurement:

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Where required only 30% of item no. 1.7

Flat No. A 501

MBR Ceiling

l/open

lobby ceiling

L/door

Dining area, ceiling

L/open

Ceiling

ceiling

Kitchen, ceiling

L/open

Entry ceiling

L/open

Room-2 , ceiling

Total=

CMB- /Page-

Date of Measurement:

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Flat No. A 501

MBR Ceiling

l/open

lobby ceiling

L/door

Dining area, ceiling

L/open

Ceiling

ceiling

Kitchen, ceiling

L/open

Entry ceiling

L/open

Room-2 , ceiling

CMB- /Page-

Date of Measurement:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

Flat No. A 501

entry door

CMB- /Page-

Date of Measurement:

For Wooden Finishing

French spirit polishing : One or more coats on old work

Flat No. A 501

MBR, Door

entry door

CMB- /Page-

Date of Measurement:

Melamine polishing on wood work One or more coats on old work

Flat No. A 501

MBR, Door

entry door

CMB- /Page-

Date of Measurement:

For Repairing and Painting

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete Where required only

stair area wall

wall (L=2.7+4/2=3.5m)

ceiling

Dining area, ceiling

L/open

l/stair

L/door

Entry ceiling

L/open

Kitchen ceiling

l/tiles

l/door

L/open

less window

less almirah

less door

MBR, ceiling

less window

near almirah, ceiling

less almirah

less door

less door toilet

less open

Servent room, ceiling

l/open

CMB- /Page-

Date of Measurement:

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Where required only 30% of item no. 1.7

stair area wall

wall (L=2.7+4/2=3.5m)

ceiling

Dining area, ceiling

L/open

l/stair

L/door

Entry ceiling

L/open

Kitchen ceiling

l/tiles

l/door

L/open

less window

less almirah

less door

MBR, ceiling

less window

near almirah, ceiling

less almirah

less door

less door toilet

less open

Servent room, ceiling

l/open

CMB- /Page-

CMB- /Page-

Date of Measurement:

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

stair area wall

wall (L=2.7+4/2=3.5m)

ceiling

Dining area, ceiling

L/open

l/stair

L/door

Entry ceiling

L/open

Kitchen ceiling

l/tiles

l/door

L/open

less window

less almirah

less door

MBR, ceiling

less window

near almirah, ceiling

less almirah

less door

less door toilet

less open

Servent room, ceiling

l/open

CMB- /Page-

Date of Measurement:

For Wooden Finishing

French spirit polishing : One or more coats on old work

Dining area

CMB- /Page-

Date of Measurement:

Melamine polishing on wood work One or more coats on old work

Dining area

CMB- /Page-