Repairing of Civil site office Building at Jeevan Nagar, Leimatak.

Amount

Dismantling sheet roofing including ridges, hips, valleys, gutters etc. stacking the serviceable material and disposal of unserviceable material within 50m lead 13.27.1 G.I. sheet roofing.

Dismantling doors, windows and clerestory windows ventilators etc. (wood or steel) shutters including choukhats architraves, holdfasts and other attachment etc. complete and stacking them within 50m lead 13.49.2 Exceeding 3sqm in area

Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m. b) Hard/Dense Soil.

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering. (2.1.6) 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 40 mm normal size)

Steel Reinforcement for R.C.C work including straightening, cutting, bending and palcing in position and binding all complete. b) Thermo-Mechanically treated bar.

Providing form works i/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4m and removel of the same for in-situ reinforced concrete and plain concrete work in. 4.1.1) Foundation, footing, base of columns etc. and mass concrete.

Providing and laying position specified grade of reinforced cement concrete, including the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level: b) 1:1.5:3(1 cement :1.5 coarse sand:3 graded stone aggregate 20mm nominal size)

Providing form works i/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4mt and removel of the same for in-situ reinforced concrete and plain concrete work in. 4.1.7.1) column, pillar, posts, and struts (square, rectangular or polygon in plan).

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttress, plinth and string courses, fillets, columns, pillars, piers, abutments, post and struts etc. upto floor Five level i/c plastering the exposed surface with cement 1:3(1cement:3fine sand) of thickness not exceeding 6mm thickness to give a smooth and even surface but excluding the cost of centering - shuttering & reinforcement. 3.2.2) 1:1.5:3( 1 cement: 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Providing form works i/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4mt and removel of the same for in-situ reinforced concrete and plain concrete work in. (4.1.8.2) Sides or soffits of beams, beam hunching, cantilevers, girders, bressumers and lintels not exceeding 1m in depth.

Reinforcement cement concrete work in beams, suspended floors, roofs having slope upto 15°landing, balconies, shelves & chajjas, lintels, bands, plain window sills, staircases and spiral stair case upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3(1 cement :1.5 coarse sand:3 graded stone aggregate 20mm nominal size).

2nd class (local 1st class) brick work in foundation and plinth in cement mortar 1:4(1 cement: 4 coarse sand).

Half brick masonry 2nd class (local 1st class) in cement mortar 1:4 (1cement:4 coarse sand) in superstructure.

Extra for half brick masonry in superstructure above plinth (floor one level) to floor two level.

Honeycomb brick work (75 mm) thick with first class brick in cement mortar 1:4 (1Cement 4 Course Sand).

Steel work in built up tubular trusses including cutting, hoisting fixing in position and applying a coat of approved steel primer red oxide zinc chrome primer conforming to IS:2074-1979) welded & bolted including special shape washer etc. complete. 10.65.1) Electric resistant welded tube (Conforming to IS: 1611-1979).

Providing & fixing MS grills of required pattern to wooden frame of window etc. with MS flats at required spacing & frames all round bars with round headed bolts & nuts or by screws. a) Plain grill.

Filling in plinth with sandy soil under floors including watering ramming, consolidation and dressing complete.

Trapezoidal pre-painted profile sheet roofing of approved brand DYNA roof or equivalent with selt drilling screws of 68 mm long Xylon coated screws with PVC washer & caps complete, excluding the coat of purlin & trusses. 10.59.2) Pre-painted Galvanised Iron sheet (PPGL) (i) Profile sheet 0.35mm / 2.8 kgs/ sqm

Trapezoidal pre-painted profile sheet for Ridges, Gutter or Valley 610 mm wide of approved brand DYNA roof or equivalent fixed with selt drilling screws of 68 mm long Xylon coated screws with PVC washer & caps complete, excluding the coat of purlin & trusses. 10.60.2) Pre-painted Galvanised Iron sheet (PPGL) (i) Profile sheet 0.35 mm / 2.8 kgs/ sqm

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering. (2.1.3) 1:2:4(1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm normal size)

12mm cement plaster 1:4(1cement:4 fine sand).

Neat Cement punning.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 30mm long the perimeter of ceiling fixed o wall/partition with the help of rawl plugs at 452mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of gypsum plain 10.61.1. 12.5mm thick tapered edge gypsum plain board conforming to IS 2095-Part I.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in charge. (Cost of aluminium snap beading shall be paid in basic item): with float glass panes of 5.50 mm thickness.

Applying one coat of cement primer of approved quality on wall surface.

Finishing walls with water-proofing cement paint of approved quality on new work (three or more coats) to given an even shade.

Finishing walls weather shield paint of approved quality on new work (three or more coats) to give even shade.

Applying ready mixed priming coat pink (Red lead primer of approved quality) on steel work.

Painting two coats (excluding priming coat) with chocolate, red grey of buff paint of approved quality on new steel work or wood work.

Providing & Fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 25.1.1) White vitreous china pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing & fixing white vitreous china flat back or wall corner type Lipped front urinal basin of 430 X260X350 mm and 340X410X265mm sizes respectively with automatic flushing cistern with standard flush pipe and CP brass spreaders with brass union and GI clamps complete, i/c painting of fittings and brackets, cutting and making good the walls and floors wherever required (24.7.1) one urinal basin with 5ltrs white pvc automatic flushing cistern.

Providing & fixing wash basin of C.I brackets,15mm C.P brass pillar tapes, 32mm C.P brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required 24.13.3) white vitreous China Wash basin size 550X400mm with a pair of 15 mm C.P.

Providing and fixing 100 mm H.C.I. soil, waste & vent pipes.

Providing & fixing G.I pipes complete with G.I fittings i/c trenching and refilling etc. (external work) 25.6.1) 15 mm diameter

Providing and fixing Brass Stop Cock of approved quality. 25.11.1) 15 mm diameter

Providing and fixing CP Bib Cock of Superior quality 25.10.1) 15 mm diameter

Providing and fixing 610 x 450 mm bevelled edge mirror of Indian make Superior Glass ( of approved quality) quality complete with asbestos sheet ground, fixed to wooden cleat with CP brass Screws and washers.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 stone aggregate 20mm nominal size) i.c finishing the top surface of concrete smooth.

Providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to I.S. 15622, of approved make, in all colours & shade, in laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete size of tile 600x600 mm

Providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12mm thick bed of cement mortar1:3(1cement :3 coarse sand) including grouting the joint with cement & matching pigments etc. complete. 9.32.1) Size of tile 600x600 mm

Providing & fixing flush door shutters decorative type core of block board construction with frame of 1st class hard wood and well matched 1st class Indian teak ply veneering with vertical grains or cross board and face veneers 3 mm thick on faces of shutters i/c providing brass butt hinges with necessary screws etc. complete as directed and specified. 7.12.2) 35 mm thick (Single Leaf)

Providing & fixing M.S. pressed butt hinges bright finished with necessary screws etc. complete. 7.80.1) 125x65x3 mm

Providing & fixing M.S. handles with necessary screws etc. complete. 7.91.2) 125mm

Providing & fixing M.S.Tower bolts (barrel type) with screws etc. complete. 7.88.1) 250x10mm

Providing & fixing M.S. sliding bolts bright finished or black enamelled with nuts & screws etc. complete. 7.85.1)300x16 mm

White glazed tiles 10mm in flooring, treads or steps & landing laid on a bed of 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) finished with flush pointing in white cement.

White glazed tiles 10mm in skirting risers of steps & dado on 10 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with white cement slurry.

Add EPF 3.25%

Add CESS 1%

Add GST @ 18% GST

M/S. NONTHOMBAM JITEN MEITEI

M/S R.K.YAISKUL SINGH