PROVISION OF WORK FOR CENTRE FOR ELECTROMAGNETIC LAUNCH TECHNOLOGY (CEMALT) AT ARDE ANNEXE KOTHRUD PUNE

Amount

SUBHEAD- I- SITE DEVELOPMENT

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

SUBHEAD - II EARTH WORK AND EXCAVATION

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Ordinary rock

Hard rock (blasting prohibited)

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Ordinary rock

Hard rock (blasting prohibited)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying and filling of local earth by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

All kinds of soil

Ordinary or hard rock

Supplying and filling in plinth with Sand under floors, including watering, ramming, consolidating and dressing complete

Extra for levelling & neatly dressing of disposed soil completely as directed by Engineer-in-charge.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for Pre & Post -CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Treatment of soil under floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor. With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

SUBHEAD- III PLAIN AND REINFORCED CEMENT CONCRETE WORK.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:

1:1½:3 (1 cement : 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Extra for providing and mixing water proofing material in cement concrete work @ 1 kg per 50kg of cement.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.

Extra for addition of synthetic Polyester triangular fibre of length 12mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement concrete/RCC/Flooring/water retaining structures by using 125gms of synthetic Polyester triangular fibre for 50 Kg cement used as per directions of Engineer-in-Charge.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all height & level. Thermo-Mechanically Treated bars. Fe-500D

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Extra for shuttering in circular work (20% of respective centering and shuttering items)

Edges of slabs and breaks in floors and walls Under 20 cm wide

Weather shade, Chajjas, corbels etc., including edges

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

SUBHEAD - IV BRICK MASONRY WORK .

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar of thickness specified by manufacturer all complete as per direction of Engineerin- Charge. ( RCC band and reinforcement all including ).

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. Cement mortar 1:6 (1 cement : 6 coarse sand)

Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : Flush/ Ruled pointing

SUBHEAD - V : PLASTERING AND SURFACE TREATMENT

Providing of 6mm cement plaster of mix in all surface with cement mortar 1:3 (1 cement : 3 fine sand) at all levels

Providing of 13 mm Gypsum cement plaster as per approved mix specified by the manufacturer all complete as per direction of Engineer in charge at all levels. Make- Gyproc/JK/Birla/Saint Gobin.

Providing of 12 mm cement plaster of mix in all surface with cement mortar 1:6 (1 cement : 6 fine sand) at all levels.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers:

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Finishing walls with textured interiors and exteriors paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Applying priming coat :

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing GI plaster mesh of nominal thickness 0.35 to 0.40 mm with zinc coating of 120 gms per sq m of all as directed.

SIGNAGES Providing and fixing of signages, modular curved frame technology,of various widths and lengths, to form suggested usages,made of aluminium extruded sections , duly anodised ,all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints, of appropriate size, print shall on 0.6mm coated,YUPO,make ,biogradable sheet printed on HP 4500 UV flat bed printer.

Toilet - Gents, Ladies & Handicap (Wall Projected(both side) Size 250x210 mm

Waiting Lounge Size - 450x210 mm

Stairs Wall Projected Size - 250x210 mm

Providing and fixing prohibition and general signage,made of 0.8mm thick aluminium sheet duly painted with Polyurethene paint of approved make and shade, aluminium sheet bented to form a curve , and supported by moulded plastic components to hold the curve , the moulded plastic components to be fixed on aluminium rails with clip on arrangment, a sper the product design of model: POLKA, manufectured by Signsutra or equivalent.Pictogram and text shall be silk screen printed as per design, in 4-7 colors or electrocut vinyl pasted as per approved make and colors.

No Smoking Size - 385x385 mm

Restricted area-authorised personnel only Size - 210x210 mm

SUBHEAD - VI : FLOORING

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and polished machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 Cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment. epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all level Granite of any colour and shade Area of slab over 0.50sqm

Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work / Marble Work

Extra for fixing marble / granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with expoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : a) Udaipur green marble

Extra for pre finished nosing to treads of steps of marble stone.

Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete

Providing and fixing Porcelain wall tiles any size (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size

Size of Tile 600X600 mm.

Size of Tile 1000 x 1000 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Double charge vitrified tile polished finish of any size

Providing & laying machine cut, mirror polished, Engineered Marble flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 20 mm thick Engineered Marble stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid & jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing & polishing etc. all complete as specified & as directed by the Engineer-in-Charge.

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red

Extra for pre finish nosing in treads of steps of granite slab.

Extra for granite in treads of steps & risers using single length upto 2 meter.

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately).

Red sand stone - 30mm thick gang saw cut stone

White sand stone - 30mm thick gang saw cut stone

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge.

Providing and fixing Glass Reinforced Concretepattern, design, thickness and color of M/S (G.R.C) Screens in approved size, UniStone make or equivalent. The Screens should be made from ‘53 grade’ White Portland Cement manufactured by ‘JK Cement’ or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by ‘Saint Gobain’ or equivalent, Super Plasticizers manufactured by ‘BASF’ or equivalent, Polymers manufactured by ‘BASF’ or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by ‘BAYFERROX (Germany)’ or equivalent. The material casting should take place in Synthetic Rubber / FRP Mould manufactured by ‘Reckli’ or equivalent. The fixing of Screens should be ‘Dry fixing’ i.e. to be done with Stainless Steel ‘L’ shaped Clamps, dash fasteners and pins.

Supply & fixing of non wooven washable wall paper with inlay work on finished surface i.e. on ceiling or wall as directed by Engineer-in-charge.

Providing & fixing in position Phenol bonded Bamboo wood wall cladding at all height with planks of sizes 10mm thick, 1800mmlength (minimum) and 130 mm wide (minimum), in approved colour,texture and finish, having Performance Appraisal Certificate (PAC)issued by Building Materials & Technology Promotion Council(BMTPC), with necesasary profiled edges fixed with 40mm SSscrews 5 nos in each tile to frame work made of second class teakwood of size 20x15 mm in centre of each tile and bottom and top ofwork height, 40x15mm placed at ends of each tile. The claddingshall be laid over backlayment of 1.00 mm thick expanded polyethylene foam of density 40kg/cum in two layers, first layer on wallsurface before fixing wooden frame and second layer on frameunder cladding. The bomboowood planks shall have minimum densityof 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendlyUV coating, all complete as per direction of Engineer in-charge.

SUBHEAD -VII : DOOR WINDOW & WOOD WORK

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality . 1.0 mm thick

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete. 2nd class teak wood 50x12 mm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of Approved Quality)

Melamine polishing on wood work (one or more coat).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) a) For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness (weight not less than 10 kg/Sqm)

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

With Polycarbonate Compact Transparent Sheet in window size 4mm to 12mm as per architecture detail with EPDM rubber / neoprene gasket etc.all complete as per direction of engineer in charge.

Providing & fixing Transparent Bullet proof glass with putty and glazing clips fix in Blast Wall, with all complete as per direction of engineer in charge.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper all inclusive all complete as per direction of Engineer-incharge.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper

Providing and fixing of rubber nylon door buffer (dia of 40mm and 50mm long) on wall with rowl plug and screw.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium casement window fastener of required length for aluminium windows with necessary screws etc. complete. Powder coated minimum thickness 50 micron aluminium.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing to existing door frames. 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion

welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant & hardware all inclusive). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel

screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent & hardware all inclusive ). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

SUBHEAD -VIII : STEEL WORK

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing and fixing 2 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. a) Using M.S. angles 40x40x6 mm for diagonal braces

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing bolts including nuts and washers complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 80 mm

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & fixing 12 mm thick frameless toughened glass in Railing of Staircase of approved brand & manufacture, including providing & fixing top & bottom clamp fixing arrangement & making necessary holes etc. for fixing required fittings, all complete as per direction of Engineer-in-charge.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.20 mm M.S. laths with 1.20 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured).

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area

SUBHEAD - IX : ROOFING & WATER PROOFING

Providing and fixing on wall face unplasticised Rigid Single socketed PVC rain water pipes conforming to IS : 13592 Type A, along with injection moulded fittings as required e.g., bends on any angle, sockets, junction, cowls, offsets, access pieces, including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, providing and fixing MS stays & clamps and cutting & making good the holes in floors and walls wherever required etc. all complete. (For Rain water pipe).

a) 110 mm diameter

b) 160 mm diameter

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diametre and weighing not less than 440 grams.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing false ceiling with Armstrong ceiling tiles 'Fine Fissured' with micro look size 600 X 600 mm of approved colour. Suspension system shall be Armstrong exposed grid system with 15mm wide T section of approved shade. Installation to comprise main runners spaced at 1200mm C / C securely fixed to the structural soffit by approved hanger at 1200mm maximum centres. The last hanger at the end of each main runner should not be greater than 450mm from adjacent wall. 600 x 600 mm modules to be formed by fitting 600mm long flush fittings cross tees centrally between 1200mm cross tees, 4mm galvanised annealeg iron wire with pre straightened to be used for suspension and also including the cost of making opening for light fittings, Grills, Diffusers, cut out made with frame of primetre channels suitably fixed all complete as per drawing and specification and direction of the engineer in charge.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick

(minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

Providing and fixing of wooden False ceiling made out of 12 mm thk commercial plywood and hardwood / GI channel , perimeter frame work, all exposed surfaces covered with Teak wood lipping / beading / 4mm thk. Teak veneer of approved sample in decorative pattern as per design and instruction by engineer in charge . Ceiling to be hanged with 16 mm dia dash fastener / GI rod hangers including making of coves insides for indirect lighting etc. all complete including two or more coats of melamine polish .

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete :Serrated with central bulb (225 mm wide, 8-11 mm thick)

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS:2645 and approved by Engineer - in- charge over the RCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment.

Laying cement concrete using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer - in- charge over 20mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to IS2645 and approved by Engineer - in- charge to required slope and treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls and slabs. After two days of proper curing applying a second coat of cement slurry admixed with proprietary water proofing compound conforming to IS:2645 and approved by Engineer - in- charge .

Finishing the surface with 20 mm thick joint less cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS:2645 and approved by Engineer - in- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making of 300x300 mm square 3mm deep. The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge. a) With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

PEB Roof Analysis, Design, Engineering, Preparation of Detailed Drawings, Manufacturing, Fabrication, Supply, Loading, Transportation to site, Unloading, Erection of STEEL PEB (PRE-ENGINEERED BUILDING) SYSTEMS, consisting of Primary structural frames such as transverse rigid frames, I-type rafters for hanger frame, lean to rafters and columns(Primary members fabricated from plates and sections with minimum yield strength of 345 Mpa or to suit design by continuous welding), secondary structural frames such as purlins, girts/runners (Pre Galvanised steel of 345 Mpa having a coating thickness of 275 gsm), eave struts, sag rods, wind bracing, flange bracing, base angles & clips, etc.,

including finishing edges by grinding, fixing in line and level with temporary bracings, providing staging, scaffoldings & working platforms at all heights and removal of same after erection, including supply of anchor bolts, grouting of anchor bolts with high strength free flow non- shrink grout mix, preparing the surface for painting, surface cleaning, wire brushing, removal of mill scale, dust, rust, oil or grease, shot blasting SA 2.5 and applying 2 coats of 35 micron (each coat) Red Oxide Primer and 2 coats of 100 micron (each coat) Epoxy paint, etc., including all labour, tools & tackles, scaffoldings, all complete as per scope of work, technical specifications and as directed by the Engineer-in-Charge.

Providing and fixing in position precoated colour sheeting in roof & wall in galvanised steel 24G. Effective width of panel will be 1000mm. Length of the panel can be varied from 2m to 11.7m. etc., all directed including self drilling screws, sealer tape, end and side laps as given below

Roof and wall panel shall be 24 gauge. Base material for colourcoated galvanized or galvalume substrate steel panels shall have minimum yield strength of 345 Mpa and will conform to the physical specifications of ASTM A-446 Grade D or A 792 or equivalent. The pure lead force zinc coating is a hot dip galvanization process conforming to ASTM A-792-AZ 150 (150 g/m) or equivalent IS:277. The painting shall be baked enamel polyster (white) or silicon polyster (coloured) with a film thickness of 1.0 mil. The reverse side shall be with 0.5 mil film thickness.

Rib, Roof & Wall panel shall have minimum 45mm deep major ribs which taper in width from 30mm to 77mm and are spaced maximum 250mm c/c. Between major ribs additional minor ribs are stiffeneing ribs spaced at maximum 83mm c/c.

Self drilling screws meeting Australian and International standard AS 3566 Class 3 (Mar 2002), with ShankGuard & Hi Grip with EPDM Washers, hexagonal Head with Chimseal 3 coated.

For crest fixing: 12G x 14TPI x 55mm Hi Teks Screws ii) For Cladding 12G x 14TPI x 30mm Hi Teks Screws iii) For Over Lapping Sheets 10 G x 16 TPI x 16mm. All screws shall have hex heads, be colourcoated to match roof or wall panels. All Hi Teks screws shall be crest fixed only.

Ultimate average pullout loads on Buildex Teks Screws shall be 7620 KN on pulin thickness of 2.4mm with gauge / TPI of 12-14.

Mechanical Properties of Buildex Teks 12 G Screw shall be minimum 8.8 KN Single Shear Strength, 15.3 KN Axial Shear Strength, 13.2 KN Torsional Strength

Sealer for sidelaps, endlaps and self-flashing window shall be 6mm wide x 5mm thick , asbestos fibre filled, pressure sensitive butyle tape. The sealer shall be non-asphaltic, non-shrinking, non-drying and non-toxic and shall have superior adhesion to metals, plastics & painted surface at temperatures from 500C to + 1040C. Sealer shall be Anabond make or equivalent. Roofing colour coated galvalume Panels

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Flashings/ Aprons.( Upto 600 mm)

Gutter (600 mm over all girth)

Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.

Providing and fixing Armor Board (SIL–FIL) of Dawn colour between expansion joints, thickness built up using 10mm specifically extruded high performance sheet minimum density 30 kg per cum and compression strength 0.21 Kg./Sqm when tested as per ASTM D-3575 including using double sided adhesive SIL tape (manufactured by Supreme Industries Ltd. or equivalent) of 25x25x2 mm at four places per Sqm to the casted surface to form the expansion joint Armor Board (SIL – FIL) will become one side of the shuttering while the expansion joint is being created, including cost and conveyance of all materials, labour charges, sundries etc. complete as per drawings and as directed by Engineer-in-Charge. 40 mm thick

Preparing the joint. Providing and laying 40 mm wide expansion joints to roof as per details shown in the drawing and filling the same with filler board & back up chord of approved make and top 40 x 20 mm gap from finished surface shall be sealed with THIOFLEX 600 two part, polysulphide sealant, manufactured by Fosroc to BS 4254 -1983 after priming using Primer 7E. Cost inclusive of sealant material, labour for necessary surface preparation, and application and excluding of filler board & back up cord.

Providing and fixing sheet covering over expansion joints with iron screws as per design. Aluminium fluted strips 3.15 mm thick. 200mm wide

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer. Using rough kota stone.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in ecommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge: Using rough Kota stone

SUBHEAD - X SANITARY INSTALLATIONS

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Supplying and fixing approved quality European water closet with FRP cistern set comprising of :

( a ) Star White glazed European water closet with wash down pattern of approved make with P or S trap fixed to floor with necessary teak wood plugs, CP brass screws, etc.

( b ) 10 ltrs. capacity PVC low level flushing cistern made of corrosive resistant materials fixed to wall with necessary brackets and screws, and plugs with matching chromium plated flush bend with float valve and flushing arrangements of slimline or equivalent.

( c ) 15 mm heavy quality flexible PVC inlet connection with brass hexagonal check nuts with washer at both ends.

( d ) Approved make plastic seat and cover (Commander or equivalent make) to match the colour of water closet and CP hinges fixed to water closet.

( e ) 15 mm CP brass Angular stop cock fixed between GI outlet and PVC inlet.

Hindware Cat No. 20012 or equivalent.

Providing, Fixing water closet for physical Handicap cruse set of make : CERA CRANE / Merino BESCO colour snow white complete including all acessories, cutting and maing good of the wall and floor whereever require EWC ' P' cinstern soft close seat cover, Twin Flush fitting, Wash Basin of Size 510X400mm with Spatula lever basin mixer and including wall mounted Grab bar 600 long- 2 Nos. wall mounted hinged rail 750X100mm, Shower chair complete as required direction of engineer in charge

Providing and fixing wash basin with CI brackets,32mm CP brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever required. W.B Hindware model 10080 /Parryware or Equivalent White vitreous china wash basin(round/oval under counter) size 580 mm x 430 mm with 15mm C.P. brass pillar tap Jaguar Model No CON-359KN & Bottle trap-Jaquar model no. ALD 769/CERA or approved equivalent, 15mm PVC connection pipe with angle valve and CP waste-Jaquar model no. ALD 709/CERA orapproved equivalent).

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar tap Jaguar Model No CON-123BKN, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require with White vitreous china flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap, 15mm PVC connection pipe with angle valve , waste coupling & 2 CI brackets (Parryware indus C0471 (CTH)/72 (SP) or equivalent).

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with fittings, standard size C.P. brass flush pipe, CP Angle stop cock along with Urinal Spreader, 32mm dia waste fitting,waste pipe, including cutting and making good the walls and floors wherever required : Urinal : Hindware Cat No. 96007 or equivalent.

Providing and fixing 16mm thick stone slab with table rubbed, edges rounded and polished, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. in Granite Stone of approved shade

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required with Kitchen sink with drain board 510x1040 mm bowl depth 200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. With Flexible pipe 32 mm dia

Providing and fixing beveled edge mirror of superior glass of approved quality complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing soap dish of approved quality including fixing with C.P. brass screws etc. complete. (Jaquar CAT NO - ACN - 1131N)

Providing and fixing C.P. Brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality colour and make. 600mm x 20mm size (Jaquar CAT NO - ACN - 1111N)

Providing and fixing C.P. Brass towel ring 200 dia size complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality colour and make. (Jaquar Cat No. ACN - 1121NR)

Providing and fixing C.P. brass toilet paper holder with concealed fitting arrangement of approved quality colour and make. (Jaquar Cat No. ACN - 1151N)

Providing and fixing Health faucet with concealed fitting arrangement of approved quality colour and make. (Jaquar ALD-565)

Providing and fixing approved type SS Double coat hooks with concealed type screws. Jaquar 1161 or equivalent approved make.

Providing and fixing 15 mm nominal bore C.P. brass short body two way bib cock 15 mm nominal bore - Jaquar cat no-23041 N/equivalent .

Providing and fixing C.P.brass long body bib cock of approved quality conforming to IS standard and Weighing not less than 690 gms. (Jaquar model no. CON-107kn/approved equivalent). 15 mm nominal bore.

Providing & fixing in position CP Soap dispenser.(Jaquar model no. ACN- 1135/approved equivalent).

SUBHEAD - XI - INTERNAL WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing this includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge. Concealed work, including cutting chases and making good the walls etc.

a) 15 mm nominal dia Pipes

b) 20 mm nominal dia Pipes

c) 25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

25 mm nominal outer dia Pipes

32mm nominal outer dia Pipes

40mm nominal outer dia Pipes

50mm nominal outer dia Pipes

65 mm nominal inner dia Pipes

80 mm nominal inner dia Pipes

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 15 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.

a) 20 mm dia

b) 25 mm dia

c) 32 mm dia

Providing and fixing Butterfly valve (upto 150mm dia with band lever operation & above with gear box operation) with SS-304 disc. Tested to a pressure not less than 15 Kg/sq.cm including rubber gaskets, flanges, nuts, bolts, washers & painting complete as required.

a) 65 mm dia

b) 80 mm dia

Providing and fixing unplasticised P.V.C connection pipe with PTMT Nuts coller and bush of approved quality and colour. With 15mm nominal bore with 45cm length

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

(a) 500 Ltrs

(b) 1000 Ltrs

Providing and fixing Storage type Water Cooler with inbuilt RO water purification system including necessary inlet/outlets, CP angle stop cock & making drain connection etc. complete including all required fittings as required. Purified water production capacity - 60 LPH, Storage capacity -60 LPH

SUBHEAD - XII - EXTERNAL WATER SUPPLY

Supply, assembly, erection, testing and commissioning of pumping system comprising the following: Vertical inline single/multistage Centrifugal pumping set with stainless steel S.S. stage casing and S.S. impellers with stainless steel shaft, cast iron suction & discharge casing, connected to suitable capacity TEFC ventilated induction motor 2 pole, 2900rpm, suitable for 415±10% Volts, 3 phase, 50 Hz A.C. supply, with 100 mm dia. pressure gauges including M.S. skid and mounting of the pumps on the skid. (Motor to be of the same make as the pump) Control panel with pressure switch, electrical wiring, cabling from panel to pumps, level controller complete with all accessories. Pump Capacity 100 lpm, at 55 m head (1 working + 1 standby) for feed to terrace tank

Supply erection testing and commissioning in position the following heavy class G.I. pipes conforming to IS:1239 cut to required lengths including all necessary fittings (conforming to IS:1879) and specials such as bends, tees, unions, reducers, flanges & plugs etc. fixing at wall/ceiling level supported by clamps, hangers etc,cutting hole in wall/floor/slab and making good the same good with cement concrete 1:2:4 / fire sealant complete as required.

a) 32 mm dia

b) 40 mm dia

c) 50 mm dia

d) 65 mm dia

e) 80 mm dia

Supply, installation, testing and commissioning of tanker inlet connection complete with 80 mm dia GI inlet piping, hose inlet connection, M.S. cabinet enclosure (epoxy painted after fabrication), pad locking arrangement, inlet flexible hose complete with all necessary arrangement.

Supply, installation, testing and commissioning of CI Butter fly valve of class PN 1.0 suitable for fixing between two flanges, including bolts, nuts, rubber insertions complete and of following sizes etc complete.

a) 50 mm dia

b) 65 mm dia

c) 80 mm dia

Supply, installation, testing and commissioning of C.I. dual plate type check valve tested to a pressure of 15Kg/sqcm. Including rubber gasket, flanges, union, nuts, bolts, washers & painting complete as required.

a) 50 mm dia

b) 65 mm dia

c) 80 mm dia

Supplying, Installation, Testing and Commissioning of CI / DI body flanged (both ends) type serviceable suction / Y strainer with (stainless steel / brass mesh) conforming to relevant IS specifications amended upto date complete including providing and fixing nuts, bolts, washers, gaskets etc. complete as required. a) 80 mm dia

Supply, installation, testing and commissioning of in position Vane Type mechanical water flow meter for following pipe size a) 80 mm dia

Constructing masonry chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I. surface box 350x350 mm top and 165 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand :10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design.

With common burnt clay F.P.S. (non modular ) bricks of class designation 7.5.

BORE WELL: Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. All types of soil a) 300 mm dia.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil a) 300 mm dia.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS:12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. (a) 150 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge (a) 150 mm nominal size dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: (a) 150mm dia

Providing and fixing M.S. clamp of required dia to the top of casing / housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. (a) 150mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). (a) 150mm Dia

Supply,erection,testing and commissioning of 3 cum per hour at 200 m head submersible pump set 3Phase-415V, 50 Hz, 2900 rpm including suitable copper armoured cable & 2 no of GI wire of 8 SWG complete with control panel as per directed by engineer in charge.

Supply & Installation of G.I Class `C' column pipe with flanges at 6m intervals including all fittings, flanges, clamps nut bolt rubber packing etc complete as require. (a) 50 mm dia

SUBHEAD - XIII - SEWERAGE DISPOSAL INTERNAL AND EXTERNAL

Internal Drainage Providing, fixing and jointing UV stabilized SWR (Type - B) pipes conforming to IS:13592 including all fittings such as bends, clamps, tees, cowls, clean out plugs, offsets, Y-tees, tees, door fittings, clips, clamps, stays etc. conforming to IS-14735, including jointing with rubber gasket fixing in sunk areas, Fixing at wall / ceiling level supported by steel clamps & hangers etc. including Cutting, chases/ holes in floors / walls / slab and making good the same after pipe have been duly laid and testing complete in all respects.

a) 75 mm dia.

b) 110 mm dia.

Providing, fixing,and jointing UV stabilized SWR (Type - B) pipes conforming to IS:13592 including all fittings such as bends as required lengths including all necessary fittings (conforming to IS:1879) and specials such as bends, tees, reducers, flanges & plugs etc. fixing at floor level with cement concrete 1:2:4 complete as per direction engineer in charge. a) 160 mm dia.

Providing, fixing, jointing and testing in position the following uPVC pipes conforming to IS : 4985 of 6 kg/cm2 pressure rating including all fittings like T - bend , elbow , reducer, clamps etc .with solvent joint and cement concrete around the pipe complete and making good the same complete as required. for internal toilet a) 32 mm dia.

Providing and fixing in position uPVC SWR floor trap conforming to IS:13592 including providing necessary steel support and as per Specification. Making proper connection cutting chase / hole in floors / slabs and bringing the same in proper condition and shape after placing the trap in right position complete as required. The hopper and trap shall be set in cement concrete mix 1:2:4 complete as required. a) 110 mm inlet and 110 mm outlet

Providing and fixing CP brass grating with frame of approved design including setting in floor with cement motor to match with floor finish as per architect requirement. a) Size 100 mm X 100 mm

Providing and fixing floor drain of size -100 mm x 50 mm of approved quality .

Providing and fixing Heavy Class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and FT. a) Size 100 mm X 100 mm

External Sewerage Excavating trenches of required width for pipe, cables etc including excavation for sockets ,& dressing of sides ,ramming of bottoms ,depth upto 1.5m including getting out the excavated soil,& then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming ,watering, etc and disposing of surplus excavated soil as directed, within lead of 50m. All kinds of soil

a) Pipes, cables etc not exceeding 80 mm dia

b) Pipes, cables etc exceeding 80 mm dia but not exceeding 300 mm dia.

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m :

Ordinary rock :

a) Pipes, cables etc not exceeding 80 mm dia

b) Pipes, cables etc exceeding 80 mm dia but not exceeding 300 mm dia.

Hard rock (blasting prohibited)

b) Pipes, cables etc exceeding 80 mm dia but not exceeding 300 mm dia.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of RCC pipes including bed concrete as per standard design :

a) 150 mm dia

b) 250 mm Dia

c) 300 mm Dia

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete

a) 100 mm diameter

b) 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipe including bed concrete as per standard design:

a) 100 mm diameter

b) 150 mm diameter

Providing and fixing square mouth SW gully trap class SP-1 complete with CI grating brick masonry chamber and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg. as per standard design. 150x100mm size P type with common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregrate 40mm nominal size ) inside plastering 12 mm thick with cement mortar 1:3 (1 Cement : 3 coarse sand) finished with floating coat of neat cement & making channels in cement concrete 1:2:4 mix (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design: Inside size 90x80cm and 45cm deep including C.I. cover with frame (light duty) 455x610mm internal dimensions total weight of cover and frame to be not less than 38kg (weight of cover 23kg and weight of frame 15 kg) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Extra for depth for manholes Size 90x80 cm Withcommon burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Construction of Septic tank in R.C.C. including excavation in all kind of soil, P.C.C. in 1:3:6 / 1:2:4 R.C.C. M25 work in foundation walls and slabs, Reinforcement steel grade Fe-500, PVC encapsulated orange colour footrest, pre-cast RCC manhole cover and frame of Heavy duty (HD 20) circular shape 560 mm internal diameter, sludge chambers etc. complete with waterproof plaster inside & outside. 100 Users.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

SUBHEAD - XIV : Road and Hardstanding

Banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m : (a) All kinds of soil

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Supplying and stacking at site.

90 mm to 45 mm size stone aggregate

63 mm to 45 mm size stone aggregate.

Stone screening 13.2 mm nominal size (Type A)

Stone screening 11.2 mm nominal size (Type B).

Red bajri.

Moorum

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineerin- charge.

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)

Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. Using grade 'A' sealing compound conforming to IS: 1834.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications : On W.B.M. @ 0.75 Kg / sqm

Providing and laying Dense Graded Bituminous Macadam using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of Engineer-in-Charge. 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity.

Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint conforming to IS : 164, on bituminous/RCC surface in white/yellow shade, including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete. New work (Two or more coats)

Providing and fixing road stud reflectors complete with nuts, bolts and washers as required as per the direction of Engineer-in-charge.

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete

450 mm dia RCC pipes.

600 mm dia RCC pipes.

900 mm dia RCC pipes.

Providing and laying Polythene sheet (125 micron thick) confirming to IS :2508 antifriction layer on the sub base course complete as per specifications.( Overlaps atjoints of pvc sheet should be 100 mm wide )

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 .cm length and drilling holes upto 10 mm dia. etc. complete.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete.

Providing and laying Kadappa (HAND CUT COBBLES ) Black Limestone Cobble stone for pathway size - 100mmx100x100mm and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge

SUBHEAD - XV : Arboriculture, Landscaping work

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Trees Plant

Supply and stacking of Bottle palm plant of ht. 210-240 cm bottom girth 30-35 cm well developed in big HDPE bags.

Supply and stacking of Plumeria alba plant of height 120-135 cm. with 2-3 branches in bags of size 30 cm as per direction of the officer-in-charge

Supply and stacking of Ficus religiosa (Peepal) plant of height 150-165 cm. in big poly bags of size 30 cm as per direction of the officer-in-charge.

Supply and stacking of Azadirachta indica ( Neem ) plant of height 120- 130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Delonix regia (Gulmohar) plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Supply and stacking of Magnolia grandiflora plant of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.v

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) :

a) Screened through sieve of I.S. designation 4.75 mm

Providing and applying anti termite treatment of infected trees i/c all branches/leaves by spraying chemical emulsion 0.5% (Chlorpyriphos 20% EC) concentration through power spray machine (@ 100 ml Chlorpyriphos per tree i/c cost of chemical) and as per direction of officer-in-charge.

Making tree guard 53 cm dia and 1.3 m high as per design from empty coal tar drums, supplied free by the department, including providing and fixing 2 nos M.S. sheet rings 50 x 0.5 mm fixed with rivets complete in all respects including painting inside and outside of tree guard with:

Complete maintenance of trees(out side of lawn area), jobs like making of basin at regular interval i/c watering,weeding,prunning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge. a)Trees for 250 no/(up to 4 & up to 3 year Slow & Fast growing group =11113.25/250=44.45 Cost for per tree per month.

Lawn Plantation Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) :

Screened through sieve of I.S. designation 20 mm

Rough dressing the trenched ground including breaking clods.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing of the ground.

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge

Weeding out of lawn by removal of all weeds and other wild growth with roots by forking including disposal of garden rubbish with all loads and lifts complete if top dressing required paid separately (cost of manure, sludge or extra good earth to be paid for separately) as per direction and satisfaction of officer in charge a)Where weeds are up to 50%

Shrubs Plantation Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

Providing and applying anti termite treatment of infected trees i/c all branches/leaves by spraying chemical emulsion 0.5% (Chlorpyriphos 20% EC) concentration through power spray machine (@ 100 ml Chlorpyriphos per tree i/c cost of chemical) and as per direction of officer-in-charge.

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) :

a) Screened through sieve of I.S. designation 4.75 mm

Supply and stacking of plant Bauhinia tomentosa (yellow) of height 60-75 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge.

Supply and stacking of plant Ficus blackii (F.vivion) (bushy) of height 150- 165 cm. with 8-10 branches and healthy foliage in earthen pots of size 30 cm as per direction of the officer-in-charge.

Supply and stacking of plant Euphorbia pulcherrima (dark red double bracts) well branched of height 60-75 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge

Supply and stacking of plant Calliandra, emarginata of height 45-60 cm. in earthen pot of size 20 cm as per direction of the officer-in-charge

Complete maintenance of shrub(out side of lawn area), jobs like making of basin at regular interval i/c watering,weeding,prunning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge.

Hedge Plantation Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Providing and applying anti termite treatment of infected trees i/c all branches/leaves by spraying chemical emulsion 0.5% (Chlorpyriphos 20% EC) concentration through power spray machine (@ 100 ml Chlorpyriphos per tree i/c cost of chemical) and as per direction of officer-in-charge.

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) :

a) Screened through sieve of I.S. designation 4.75 mm

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

Hedge Plant

Supply and stacking of plant Dombeya mastersii of height 60-75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of plant Ficus panda of height 45-60 cm. with 6-7 branches and healthy foliage in p.bag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of plant Euphorbia pulcherrima (dark red double bracts) well branched of height 60-75 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge

Supply and stacking of plant Thuja compacta of height 75-90 cm., conical shaped, well formed with healthy foliage in earthen pots of size 30 cm as per direction of the officer-in-charge.

Cutting of designer hedge/edge removing of cut materials, cleaning, hoeing of hedge/edge bed watering manure and applying insecticides and fungicides etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge

Providing & displaying plants Aster Hybrid variety in different colour, well developed with fresh & healthy foliage in full bloom 23 to 30 cm ht. in 20 cm Earthen Pot/Plastic Pot & as per direction of the office-in-charge

Providing & displaying plants Aster Hybrid variety in different colour, well developed with fresh & healthy foliage in full bloom in 20 cm Earthen Pot/Plastic Pot & as per direction of the office-in-charge

Providing & displaying plants Marigold (Tagetes) inca hybrid different colour having 30 cm & above ht., with 6 to 8 flowers in bloom & blooming condition, well developed pot should be fully covered with fresh & healthy, foliage and flowers in 20 cm Earthen Pot/Plastic Pot & as per direction of the office-in-charge

Providing & displaying plants Celosia well developed fresh & healthy 20 to 25 cm ht. (attractive multi branching at blooming stage in 20 cm Earthen Pot/Plastic Pot & as per direction of the office-in-charge

Providing & displaying plants Acalypha plant diffreent colour well developed, fresh & healthy with good foliage, multi branch 30 to 45 cm ht. in 20 cm Earthen Pot/Plastic Pot & as per direction of the office-in-charge

Providing & displaying Bismarkia Palm plant 115 to 180 cm ht. well developed 12 & above good colour fresh & healthy leaves in 40 cm cement pot as per direction of the office-in-charge

Providing & displaying Bougainvillae named variety, Sobhra, Thima, Marry paimar, Cherry blosoom etc. well developed with fresh & healthy bushy plant in full bloom 75 to 90 cm ht. in 40 cm cement pot as per direction of the office-in-charge

Providing & displaying Latania Rubra Palm plant well developed with fresh & healthy foliage 150 to 180 cm ht. with 6 to 7 leaves in big 35 cm cement pot as per direction of the office-in-charge

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide , lawn mover and brush cutter with fuel will be provided by the Department & other T & P material/articles shall be provided by the contractor.) a) Prestigious works / H.M. house & officers entitled to free Per Sqm accommodation.(as per yard stick 1Mali =1.00Acre)

SUBHEAD - XVI : Furniture

Supply of Computer chair with arms with specification as under :- Overall height - 775mm, Type of chair- central tilt synchronic, Seat Height (Min) - 432mm, Backrest height & width- 490mm & 500mm respectively, Seat width & Depth - 500mm & 465mm respectively, Type of backrest - Cushion, Material of fabric of Seat & backrest - Upholstered with 100% polyester fabric, Density of polyurethane Foam used in seat & backrest - 45±2kg/Cum, Colour - as per approved by engineer-in Charge, etc. All complete. make: Godrej/Equivalent

Supply of Computer Table size 1200x600x750 mm made out of 19 mm thick commercial board with 1 mm thick laminate on sides & front. Top to have 25mm thick postformed board, having drawer, key board and provision of CPU trolley, all drawer ride on telescopic sliding channel and back covered with 6mm thick commercial ply all exposed edges covered with teak wood lipping or PVC lipping (as required) and finish with melamine polish etc., all complete.

Supply of Officer Table made out of 19mm thick commercial board with 1mm lamination on sides and front, top with 25 mm thick postformed board, having 1 Nos drawers ride on telescopic channels & 1 Cupboard with shelf, (Left/Right hand side as required) with locking arrangement and foot rest of size 75x30mm, all exposed edges to have teak wood/rubber wood lipping with melamine polish and inner sides with sprit polish etc., all complete. (a) Table of size 1800x900x750mm

Supply of Executive Table of size 2400 x 1050 x 750mm made out of 19mm thick commercial board with 3.5mm veneer of approved shade on top, sides and front, along with drawer. Table top edging will be 15x32mm thick with half round moulding. All exposed edges to have 4mm thick teak wood beading with 75x30mm teak wood foot rest with all necessary hardware, locking arrangement etc. All exposed surfaces shall have approved shade of melamine polish & inner surfaces finished with Spirit polish etc, all complete.

Supply of High back Executive revolving chair with head rest and arms with specificastion as under:- Arm Material-PU, Chair Height- (min)1100mm, Backrest Height -800mm, Backrest Width - 450mm, Seat Depth and Height -390mm & 400mm respectively, Paint Type Powder coating , Density of Polyurethane Foam used in Seat 65 kg/Cum. Thickness of Polyurethane Foam used in Seat -50mm, Material of Fabric of Seat Cover- Net, Material of Fabric of Back Cover- Net, Colour – as per approved by engineer-in Charge, etc. All complete. make: Godrej /Equivalent.

Supply of Medium back revolving chair with arms with specification as under :- Overall height - 775mm, Type of chair- central tilt synchronic, Seat Height (Min) - 432mm, Backrest height & width- 490mm & 500mm respectively, Seat width & Depth - 500mm & 465mm respectively, Type of backrest - Cushion, Material of fabric of Seat & backrest - Upholstered with 100% polyester fabric, Density of polyurethane Foam used in seat & backrest - 45±2kg/Cum, Colour - as per approved by engineer-in Charge, etc. All complete. make: Godrej/Equivalent

Supply of Visitor chair with arms with specification as under :- Chair Overall height - 815mm, Seat height (Min) - 450mm, Seat Depth & width - 450 & 500mm respectively, Backrest height & width - 490 & 500mm respectively, Type of Seat & backrest - Padded with polyurethane foam, Material of fabric of seat & back cover is vacuum formed from ABS sheet & upholstered voila fabric made from 100% polyester, Density of polyurethane foam used in seat & backrest-45±2kg/Cum & colour - as per approved by engineer-in-charge, etc. All complete. make: Godrej/Equivalent

Supply of Wooden Work bench of size 2000 x 750mm and height 900mm made out of 19mm thick commercial board with 1 mm thick decorative laminate having one drawer and one cupboard, Drawer ride on telescopic sliding channel, top to have 2 mm thick Alluminium sheet and antistatic matt & connected to antistatic discharge system,having 300(H) x 100(D) x 2000(L) Wooden Box for Provision of 2 Nos. 5/15Amp Switch and socket,Box made out of 19mm thick commercial board with 1mm thick laminate & all edge covered with teak wood lipping all inner surface finish with spirit polish and outer edges finish with melamine polish etc., all complete.

Supply of standard steel almirah of large size 1980 x 486 x 916mm with 4nos. of adjustable shelf made out of M.S sheet conforming to CR-2 Grade. Sheet thickness of side, top, bottom & back of Almirah is 0.8mm minimum and sheet thickness of door 1mm. Three way bolting & locking arrangement with powder coating, having pedestal width 75mm & pedestal depth 120mm.Colour of paint as per approved by Engineer-In-Charge,etc. All complete. make: Godrej /Equivalent

Supply of Standard steel Almirah of Medium size 1266x750x430mm with 3 Nos of adjustable shelf.Made of M.S Sheet conforming to CR-2 Grade Sheet thickness of side, top, bottom & back of Almirah is 0.8mm minimum and sheet thickness of door 1mm. . Three way bolting & Locking arrangement with Powder coating. Colour of paint as per approved by Engineer-In-Charge. Etc. all complete.Make : Godrej /Equivalent.

Supply of Conference Table ('U' Shaped) to seat 25 persons made out of 19 mm thick commercial board with 3.5 mm teak veneer on top and top edging will be 35x75mm thick with half round moulding. 19 mm thick commercial board tapered foot rest, vertical member with 19mm thick commercial board. Back with 19mm thick commercial board including 3.5 mm thick teak veneer all exposed edges to have teak wood beading including melamine polishing etc., all complete.

Supply of Discussion Table of size 1800 x 900 x 750 mm made out of 70 X 70 mm teak wood legs and 95 x 30mm sides rails and double foot rest, with 25 mm postformed top including melamine polish etc., all complete.

Supply of Center table of size 1050 X 600 X 450 mm made out of 45 X 45 mm tapered teak wood legs and side rail 70 X 25mm thick teak wood and top to have 8mm thick Glass with teak wood moulding including melamine polish etc., all complete.

Supply of Side table of size 400 X 450 X 450mm made out of 19 mm thick commercial block board & sides covered with 3.5mm teak veneer with one drawer ride of telescopic channels, back with 6mm thick commercial ply and top to have 3.5mm thick veneer & egdes covered with teak wood/rubber wood lipping including melamine polish etc., all complete.

Supply of Sofa made out of 50 x 30mm second class hard wood frame and 100 mm thick high density foam on seat & back with 50 mm thick rubber foam quilting with 20 mm thick U foam of 32 density including upholstery with fabric of approved shade and quality, with wooden arms etc., all complete.

(a) Sofa Single Seater

(b) Sofa Two seater

Supply of Reception Counter Table of size 2400 x 1050 x 750mm made out of 19mm thick commercial board with 3.5mm veneer of approved shade on top, sides and front, along with drawer. Table top edging will be 15x32mm thick with half round moulding. All exposed edges to have 4mm thick teak wood beading with 75x30mm teak wood foot rest with all necessary hardware, locking arrangement etc. All exposed surfaces shall have approved shade of melamine polish & inner surfaces finished with Spirit polish etc, all complete.

Supply of Side Rack of size 1200 x 450 x 750mm made out of 19mm thick commercial board with 3.5mm veneer of approved shade on top sides and front, along with 3 drawer , provision for CPU and one Keyboard tray (Left /Right hand side as required). All drawer ride on telescopic sliding channels . All exposed edges to have 4mm thick teak wood beading with all necessary hardware, locking arrangement, etc. All exposed surfaces shall have approved shade of melamine polish & inner surfaces finish with Spirit polish all complete.

Supply of TV Stand standard size and shape all complete fitting with nut bolt etc as per direction of engineer in charge.

SUBHEAD - XVII : Internal Electrification Work & Power Wiring:

Point Wiring for Light/ Fan/ exhaust fan with 2 runs of 1100V grade 1.5 Sq.mm & 1 run of 1.5 Sq.mm FRLS insulated multistranded Copper wires, run in & including 25mm dia, 2mm thickness FRLS PVC ISI mark conduits concealed in wall after necessary chase cutting with finishing/surface in wall / ceiling conforming to IS 732 including all accessories such as junction boxes, conduit bends, elbows and ceiling rose, anodised GI Switch box with modular switch and the box covered with front plate.

a) One Lights point controlled by one 6A switch.

b) Two Lights point controlled by one 6A switch.

c) Three Lights point controlled by one 6A switch.

d) Four Lights point controlled by one 6A switch.

e) Exhaust fan point controlled by one 6A switch including ceiling Rose.

f) One ceiling fan point controlled by one 6A switch With 100W step type Electronic regulator including Concealed MS fan hook box.

g) Call bell point with 6A Bell push with Buzzer

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed heavy FRLS PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supply and wiring for 6A socket outlet with 2 runs of 2.5 sq. mm FRLS insulated multistranded Copper wire and 1 run of 1.5 sq. mm FRLS insulated multistranded Copper earth wire in existing raceway/conduit. supply and fixing of 6A 5 Pin socket with 6A modular switch in anodized GI box and front plate complete with fixing accessories etc. as required. (Independent)

Supply and wiring for 6A socket outlet with 2 runs of 2.5 sq. mm FRLS insulated multistranded Copper wire and 1 run of 1.5 sq. mm FRLS insulated multistranded Copper earth wire in and including heavy duty 25 mm dia FRLS PVC conduit concealed in wall after necessary chase cutting with finishing / ceiling / below work stations along with required accessories, supply and fixing of 2 nos. 6A 5 Pin socket with 02 nos. 6A modular switch in anodized GI box and front plate complete with fixing accessories etc. as required.

Supply and wiring with the following size 1100V grade FRLS insulated multistranded Copper wires in and including suitable size heavy duty PVC conduit concealed in wall after necessary chase cutting with finishing / surface on wall / ceiling including all accessories such as junction boxes, bends elbows and end termination with suitable lugs. a) 2 Runs of 2.5 sq.mm wires with 1 Run of 1.5 sq.mm in 25 mm dia PVC conduit ( For circuit wirings)

Light/Fan Fixtures Supply, Installation, Testing & Commissioning of the following Light Fixture with lamp, Control Gear & All necessary accessories. Luminaries with all electrical accessories & it should be energy efficient, etc are prewired up to the terminal block & mounted on a removable control gear module for ease of maintenance. All electrical connections of the control gear module with the rest of the luminaries should be click fix & require use of no tools. Mounting options should be for both lateral as well as pole top mounting with Lamp Control Gear & Fixing Accessories. All fixtures shall be white colour & supplied with white lamps. All the light fixtures will be finally approved by Architect / Consultant/ Department. Architect / Consultant / Department reserves the right to reject the fittings suggested by the contractor.

a) 10W BULKHEAD LIGHT MAKE-PHILLIPS CAT NO. WT202W LED6S NW PSU S2 PC SJHDJFJ

b) 22W LEDBatten surface mounted fixture (Philips : BN021C LED22S PSU CW GR)

c) 38W LED LIGHT MAKE-PHILLIPS CAT NO. RC366B LED33-6500 PSU OD WH

d)34W LED Light Philips Cat No.- RC380B LED43S-6500 G5 L3W12 PSU OD

e) 11W LED Mirror wall Light Fixture. (Make: Philips Cat No. 31165 or Equivalent.)

f) 15W LED Light MAKE-PHILLIPS CAT NO. DN194B LED16S-6500 PSU WH S2

g) 32W Extruded Aluminium Suspended LED MAKE-PHILLIPS CAT NO. SM270C LED 30S 6500 PSU WH

h) Philips 5m Cove Light with Driver Warm White MAKE-PHILLIPS CAT NO. SKYCove 5M WW with driver

i) 15W LED (Slim profile surface mounted downlight ) MAKE-PHILLIPS CAT NO. SM251C LED16S- 6500 PSU WH

j) 38W LED MAKE-PHILLIPS CAT NO. SM365C LED33-6500 PSU OD WH

k) 169W LED ELITE HIGHBAY WITH ACCESSORIES MAKE-PHILLIPS CAT NO. BY718P LED250/CW PSU NB IN

l) 135W LED ELITE HIGHBAY WITH ACCESSORIES MAKE-PHILLIPS CAT NO. BY718P LED200/CW PSU NB IN

m) 76W LED PURE SPACE WITH ACCESSORIES MAKE-PHILLIPS CAT NO. CR652B LED80S-6500 PSU CA TO W60L60 WH

n) 70W LED WITH ACCESSORIES MAKE-PHILLIPS CAT NO. BY150P LED76S CW PSU HE SY120 FG GR LILO

o) 34W LED INDUSTRIAL BATTEN MAKE-PHILLIPS CAT NO. BN308C LED40S-6500 L120 PIR WH

p) 16W LED INDUSTRIAL BATTEN MAKE-PHILLIPS CAT NO.BN308C LED20S-6500 L120 PSU WH

q) 7W LED LIGHT MAKE-PHILLIPS CAT NO.DN295B LED8S-6500 PSU WH

r) 32W, 2'X2' LED luminaire with high transmitive diffuser LED LIGHT MAKE-PHILLIPS CAT NO.RC380B LED36S-6500 G5 L60W60 PSU OD

Ceiling Fans Supply, installation, testing and commissioning of the single phase heavy duty grease filled double ball bearing, aerodynamically designed heavy gauge aluminium blades, copper wounded, required length down rod, capacitor and impregnated silicon stamping motor etc.a 1200 mm sweep, brilliant white/As directed by Engineer-In-Charge without regulator).

Supply, installation, testing and commissioning of the single phase heavy duty grease filled double ball bearing, aerodynamically designed heavy gauge aluminium blades, copper wounded, required length down rod, capacitor and impregnated silicon stamping motor etc.a 1400 mm sweep, brilliant white/As directed by Engineer-In-Charge (without regulator)

Exhaust Fans Supply, Installation & Testing of following Suitable RPM exhaust fan suitable for single phase, 240V, AC supply complete with motor, MS louvers, mounting brackets all accessories etc complete.

a) 300mm Sweep (Metallic)

b) 450mm Sweep 900 Rpm (Heavy Duty exhaust fan)

c) 600mm Sweep 900 Rpm (Heavy Duty exhaust fan)

Supply, installation, testing and commissioning of 450mm sweep air circulator fan,3 speed control, 1Phase, heavy duty, fans including electrical connection, all fixing accessories/ installation materials as required, complete.

Supply, installation, testing and commissioning of 600mm sweep air circulator fan, 3 speed control, 1 Phase, heavy duty, fans including electrical connection, all fixing accessories/ installation materials as required, complete.

Power Wiring Supply, installation, testing and commissioning of 6 / 16A, 5 pin shuttered type socket controlled by one 16A modular switch of combination type with indication lamp including wiring with 2runs of 2.5sq.mm & 1run of 1.5sq.mm FRLS insulated multistranded copper conductor wire of 1100V grade laid in heavy gauge 25mm dia FRLS PVC conduit concealed in wall / ceiling including all accessories such as junction boxes, conduit bends, elbows and ceiling rose, anodised GI switch box of adequate size with modular switch, socket and the box covered with front plate. Cutting, chases in wall and making them good after fixing modular type switches as per requirement in sheet steel boxes of adequate sizes to accommodate switches, sockets, etc. complete as required. (Wiring from DB to Socket)

Supply, installation, testing and commissioning of factory made 20A, metal clad socket outlet controlled by 20A, 10kA, SP MCB, in and including MS painted box in concealed manner of adequate sizes including plug top with necessary accessories including wiring with 2runs of 4.0sq.mm & 1run of 2.5sq.mm FRLS insulated multistranded copper conductor wire of 1100V grade in heavy gauge 25mm dia FRLS PVC conduit concealed in wall / ceiling along with required accessories including all accessories such as junction boxes, conduit bends, elbows and ceiling rose. Cutting, chases in wall and making them good after fixing of metal clad socket outlet as per requirement etc. complete as required. (Wiring from DB to metal clad socket outlet)

Supply Installation Testing and commissioning of SPN/TPN MCB Double door Distribution boards dust and vermin protected and rated for 230/415V Single/Three Phase AC supply operation including incoming MCB /ELCB as per specifications and required capacity Neutral bar and Earth terminal complete as required and installed in concealed in wall after necessary chase cutting with finishing / surface in wall including all fixing materials required. MCBs shall conform to IS : 8828 and ELCB shall conform to IS :12640. All MCBs shall be 'C' Curve. DBs shall be provided along with required wire adopter boxes around the DB as required and dummys for spare ways in the DB (No claim shall be allowed for the same).

a) 8Way SPN MCB DB with 40A, 100mA 2Pole RCBO as incomer and 6nos 6-32A SPMCBs as outgoings.

b) 4Way TPNMCBDB with 40A,100mA 4Pole RCBO as incomer and 12nos 6-32A SPMCBs as outgoings.

c) 4Way TPNMCBDB with 63A,100mA 4Pole RCBO as incomer and 12nos 6-32A SPMCBs as outgoings.

d) 6Way TPNMCBDB with 63A, 100mA 4Pole RCBO as incomer and 18nos 6-32A SPMCBs as outgoings.

e) 8Way TPNMCBDB with 63A, 100mA 4Pole RCBO as incomer and 24nos 6-32A SPMCBs as outgoings.

Supply installation testing and commissioning of Vertical type MCB Double door Distribution boards dust and vermin protected and AC supply operation including incoming MCCB/ MCB/ ELCB / RCBO as per specifications and required capacity Neutral bar and Earth Terminal complete as required and installed in concealed in wall after necessary chase cutting with finishing / surface on wall including all fixing materials required. All MCBs shall be "C" Curve. a)8 Way VTPN MCBDB with 160A, 25kA 4 Pole MCCB as incomer and 8Nos 63A TP MCBs as outgoing..

Supply wiring testing and commissioning for circuit/ submain wiring alongwith earth wire with the following sizes of 2xwy Cu. armoured cable in surface/ recessed 32/40mm, 2.00mm thick PVC conduit/ HDPE pipe Complete as required or directed by Engineer-In Charge.

a)3 Core 6 sq.mm armoured (Copper)

b) 4 Core 10 sq.mm armoured (Copper)

c) 4 Core 16 sq.mm armoured (Copper)

Supply, installation of 8 mm dia, MS hook in the slab for mounting light fixtures

Telephone & Lan Wiring- Supply & fixing of RJ - 11 modular type telephone sockets with shutter in a GI box with front plate and in concealed manner by cutting chasing in walls and making them good after fixing socket, etc., complete as required.

Supply & fixing of RJ - 45 modular type LAN sockets with shutter in a GI box with front plate and in concealed manner by cutting chasing in walls and making them good after fixing socket, etc., complete as required.

Supply and fixing of TV outlet (RG6) with 14 gauge anodised GI box with front plate suitable for RG6 Cable

Supplying and laying of 2 Pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone wire in the surface/ recessed 25mm dia. heavy gauge FRLS PVC conduit as required. (Telephone cable conforming to DOT specification)

Supplying and laying of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed 25mm dia. heavy gauge FRLS PVC conduit as required.

Supplying and laying of 10 Pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, armored telephone cable in the surface/ recessed Suitable dia. heavy gauge FRLS PVC conduit as required. (Telephone cable conforming to DOT specification)

Supplying and laying of 20 Pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, armored telephone cable in the surface/ recessed Suitable dia. heavy gauge FRLS PVC conduit as required. (Telephone cable conforming to DOT specification)

Supplying and fixing of 8-way spliters in die cast Al. casing etc complete.

Supply and installation of following size Krone connectors in MS box in concealed manner by cutting chasing in walls and making them good etc complete as required.

a) 10 Pair

a) 20 Pair

b) 50 Pair

Supply and laying of following pair 0.5mm dia Jelly filled armoured copper conductor Telephone cable in ground at 600mm below ground level including excavation, all kinds of soil, SDR & Hard Rock and refilling of earth, laying of cables, providing protection with sand and brics on top and side and cable route markers at every 15 mtrs interval and also at the turnings. complete as required and as directed by Engr-in-charge. (Telephone cable conforming to DOT specification)

a) 10 Pair

b) 20 Pair

c) 50 Pair

Supply, Installation, Programming and testing of EPABX system Advanced New Nextgen Business Communication Server With IP/ISDN and Unified Communication Capabilities Configuration:-06 Trunk Lines, 02 Digital Ports, 64 CLI Based Analogue SLT Extension etc. as complete as required.(Make: Panasonic)

RACEWAY Supply, installation, testing and commissioning of following sizes PVC raceway with cover - above and below floor/ceiling / wall as per direction of engineer in charge with necessary supporting to distribute Power, Data and Telecom cables including junction box, riser, coupler etc including all accessories.

a) 100 x 38mm two compartment

b) 150 x 38mm three compartment

Supplying and laying of following size HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS code complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required a)90 mm dia HDPE Pipe

SUBHEAD - XVIII : Shop Electricals:

Supply, installation, testing and commissioning of 3 Phase and Neutral 415V, 4 wire Free Standing Floor mounted MV panels made out of 14 SWG MS sheet after seven tank process and painting with Epoxy powder coating. The panel shall consist of suitable rating TPN Aluminium busbar (at the rating of 0.8A/Sq.mm) supported with DMC/ SMC barriers and colour coded with Heat shrinkable sleeves. The metering shall be provided as specified.

All MCCBs of 250A and above shall be microprocessor based with inbuilt overload & earth fault protection (Built-in LSIG release). Digital Multifunction shall be similar to Make : Socomec,/equivalent. All MCCBs shall have Icu = 100% Ics. MCCBs and MCBs shall have min. 35kA & 10kA short circuit rating respectively. Transient Voltage Surge Suppressor shall be similar to Make : Obo Betterman,/ Equivalent. The panel shall have extended busbar for terminating higher size cables. The panel shall have suitable size of cable chamber for incomer and outgoing cables. Due to voltage drop the no. of cable runs and sizes got increased.

Supply fabrication,erection and commissioning of 415V 2500A 4P non phase seggregated Bus duct (Outdoor) made out of 14SWG MS sheet with painting after Seven tank process and consisting of 2500A 4P Aluminium Busbars (@0.8A/sq.mm) including flexible braided connections at the ends to facilitate connections and running 2runs of 50X6mm hot dip galvanised GI strip along the Bus duct complete as required. The Busduct shall be got manufactured only from Panel Builders with CPRI Test certificate.

Interlocking : Electrical interlocking for Incomers & Bus couplers Busbars : 2500A 4P Aluminium Busbar-1set Outgoings : 1000A 50KA 3P ACB –2 No 800A 50KA 4P ACBs –3 No 100A 25KA 4P MCCBs – 7 No 63A 16KA 4P MCCBs – 5 No 63A 25KA 4P MCCBs – 2 No 63A 10KA DP MCBs – 1 No 40A 10KA 4P MCBs – 2no 40A 10KA DP MCBs – 1no 70A AC1 duty Contactor with time switch control -1set 20A 10KA 4P MCBs – 09 Nos

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required. (80 mm dia)

Supply and laying of 80mm dia. Class B G.I. pipes surface mounted on ceiling & embedded in wall including all fixing accessories, complete as required.

Supply and fixing of following size FRP cable trays including hot dip GI structural supports & anchor fasteners for fixing the cable trays, including 2runs of 25x5mm GI strip along with cable trays etc., complete as required. Composite FRP cable bearers shall be manufactured in accordance with NEMA FGI-1984/EIL-50-OEDS-422 or latest and ASTM –E84 /IS-6746 or latest standards. The Pultruded Cable Bearers should have a minimum thickness of 4.0mm for all sizes. Perforated type cable Bearers 50mm width is to be provided in 4.0mm thickness. Cable Tray Accessories shall

be of same materials of cable trays & it includes Horizontal & Vertical Bends, Tees, Reducers, and Cross etc. with minimum Bending Radius of 300mm. Coupler Plates Shall be of same materials of Cable Trays & 2 nos. required for each length of the cable tray with Hardware of SS 316.Factory inspection for cable trays and third party lab certification are required for approval before dispatch to site. Refer technical specifications for FRP Cable Trays.

a) 150mm wide x 50mm deep x 4mm thick, perforated type without cover

b) 300mm wide x 50mm deep x 4mm thick, perforated type without cover

c) 450mm wide x 75mm deep x 4mm thick, ladder type without cover

Supply and fixing of following size Powder Coated Cable Trunking made out of 2mm thick base and cover, couplers & anchor fasteners for fixing the cable trunking, complete as required.

a) 100mm wide x 40mm deep powder coated trunking with cover

b) 150mm wide x 40mm deep powder coated trunking with cover

c) 300mm wide x 40mm deep powder coated trunking with cover

SUBHEAD - XIX : Lightning Protection:

Earth Stations for Lightning Protection a) Providing GI Electrode Earthing with 40 mm dia and 3 meter length, The electrode should be hot-dip galvanized with upto 120 micron. The GI Strip In Pipe Electrode shall be pre-filled with Crystalline Conductive Material (CCM) . The GI electrode shall be surrounded with 50 kg JAM Fill compound to provide maximum contact between the electrode and the soil. Backfill compound should be eco-friendly and having RoHs certification. GI Electrode Earthing should be maintenance free and dose not required regular manual addition of water. GI Electrode Shall be tested from CPRI. The earthing pit should be cover with FRP pit cover of 300x300mm bottom and 200x200m with 150mm height in green colour. as per JAM 193.

Supply and laying of following size earth strips with including connection/ terminating to Earth Station with G.I. nut-bolts, spring washer, bi-metallic strip, exothermic welding etc. as required.

a) 32 X 6mm Aluminium strip conductor with DMC Insulated Supports on 150x150x100mm PCC blocks at Building's Terrace Level

b) 32 X 6mm Aluminium strip conductor with DMC Insulated Supports without PCC blocks

c) 50 X 5mm hot dip GI Strip laid in Ground

Supply and fixing of weather proof 14 SWG GI test link box of size 150 x 100 x 100 mm along with bi-metallic strip and all fixing accessories etc., complete.

Supply and fixing of vertical air terminals comprising of 1.5 Mtr. long 25mm dia copper thick pipe with copper sphere on top and 5 Nos. 6mm dia. 90mm long copper spikes fixed by threading arrangements to copper sphere, 150x150x5mm aluminium base plate including and fixing of suitable mounting arrangements for air terminal on the top of the buildings/ high mast/ tower as required and as per standards, complete as required.

SUBHEAD - XX : Earthing System:

Earth Stations for Body Earthing, Transformer, DG Sets, Special Earthing, UPS Systems :

a) Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

b) Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

c) Providing Chemical type maintenance free Earth station with consisting of 40 mm dia, standard length (as per equipment supplier) electrode capsule, filled with earth enhancing compound, seald at both ends and brazed lead for connection at one end, suitable for direct installation at site, at a depth of 2.5mtrs. Earth Enhanced compound upto a depth of 2.0meters arround the electrode capsule. Brick chamber & CI Cover complete

d)Supply, laying and testing of earth conductor with 28mm dia MS rods in ground at 300mm below ground level in a grid of 1000X1000mm including cutting, welding with 75X6mm MS strip at junctions etc as required. Including Back filling fine soil /clay without stone or cement material

Supply and laying of following size earth strips at 0.5 Mtr below ground including excavation and refilling of earth when laid in ground and with all fixing accessories when laid in trench with including connection/ terminating to Earth Station with G.I. nut-bolts, spring washer, bi-metallic strip, exothermic welding etc. as required.

a) 25 X 5mm hot dip GI strip laid in ground

b) 25 X 5mm hot dip GI strip on cable trays/ walls without excavation

c) 50 X 5mm hot dip GI strip on cable trays/ walls without excavation

d) 25 X 5mm Electrolytic Grade Copper strip in ground

e) 25 X 5mm Electrolytic Grade Copper strip on cable trays/ walls without excavation

f) 50 X 5mm Electrolytic Grade Copper strip in ground

g) Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

h) 25 X 5mm Electrolytic Grade Copper strip with DMC insulated supports

i) 10.0 sq. mm. Copper green PVC insulated wire on cable trays/ walls without excavation

j) Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

k) Providing and fixing of earth bus of 25 x 5mm Electrolytic Grade Copper strip & 500mm overall length with drill of M8 at every 25mm interval mounted on insulators

l) Supply and fixing of Static Discharge Handles made out of 20mm dia and 600mm length Copper Rod fixed on wall with brass spacers and connected to copper strip

Providing Spiral coil earthing with 8 SWG GI wire including spreading of salt and charcoal as per IS 3043/87 with latest amendments.

SUBHEAD - XXI : Fire Alarm System:

Supply, installation, testing and commissioning of UL Listed & FM approved Microprocessor based Intelligent Addressable Fire Alarm System with required One Loop in the same cabinet with loop capacity upto 250 detectors and devices (Minimum 125 detectors and 125 devices to each loop) with battery back up of 24 hours in normal condition & 30 mins in alarm condition. The panel shall be networkable & expandable. The panel should be modular, decentralized. The panel shall be with atleast 640 character LCD display ,One loop panel with loop cards, 640 character with in / out media convertors

Supply, installation, testing and commissioning of UL Listed & FM approved Intelligent Addressable type multicriteria detector (Photo + Heat) with standard base, capable of being addressed electronically. Manual Addressing (Dip/ Rotary Switches) not acceptable, complete as required and as per specifications.

Supply installation, testing and commissioning of addressable self aligned motorized addressable Beam detector (Set of Emitter & Receiver) with LED status indicator covering maximum range, sensitivity measurement filters and other mounting accessories with addressable monitor modules, along with complete accessories.

Supply and fixing of Remote response indicator having twin LED flush mounted on false ceiling/wall of same make as detectors and panel.

Supply, installation, testing and commissioning of analogue addressable loop sounders with all fixing materials.

Supply, installation, testing and commissioning of UL Listed & FM approved Addressable Double action manual pull station, capable of being addressed electronically.

Supply, installation, testing and commissioning of Ul Listed analogue addressable type monitor Modules along with all fixing accessories.

Supply and laying of twisted pair 1.5sq.mm shielded FRLS insulated copper conductor flexible wire through existing MS Conduit.

Supply and fixing of 25mm dia 16SWG MS conduit concealed/ Surface in wall/ Ceiling/ above false ceiling including painting with 2 coats of Red colour paint for exposed part and all fixing accessories/ materials.

Supply, installation, testing and commissioning of weather proof type analogue addressable Ordinary Pull Type Manual call points on Stand post made out of 1500 mm long 50x50x6mm Galvanized channel fixed in ground with concrete coping as required.

Supply, installation, testing and commissioning of fault isolator modules with protective housing.

Supply, installation, testing and commissioning of 2.5 Km range Siren with Weather proof motor with 220V 50HZ AC Supply operation with required power contactor, MPCB for control all in a weather proof enclosure near motor including all installation materials as required.

Supply and laying of 1.1 KV Grade PVC insulated PVC sheathed copper conductor armoured 3C x 2.5sq.mm cable confirming to IS 1554 for power cabling to Siren located on the top of the building / on wall surface and can be used to connect repeater panel etc. complete

Supply, installation, testing and commissioning of UL Listed intelligent Addressable network control Active Repeater panel with OFC network media communication module on FACP network configuration to monitor and control all local fire alarm control panels located in individual buildings built in buzzer, optical fiber connectivity and RS 485 port on CPU board with optional network software connectivity, fire/ fault indicators, audio visual signals, battery, battery charger, central processing unit 80 character display unit complete in all respects.

Supply, installation, testing and commissioning of Fire alarm management software system and graphical display with PC interface to network the installed fire alarm panels using a network manager program and the following shall be pre-equipped with : a) Preparation of graphics compatible to fire alarm monitoring software of buildings and connected with slave panels including layout of the building and wiring diagram of the fire alarm system b) Interconnecting the same with fire alarm software located at master panel testing the parameters and operations of individual detectors and slave panels c) Establishing two way communication with master panel and slave panels.

PC with following Items: CPU comprising of Intel I-5 processor, 4GB RAM, 500 GB HDD, Intel mother board of 3000MHz, 19" LED Monitor, key board, mouse, network adopter, graphic card connected to Fire alarm panels. The CPU shall be suitable to integrate number of FACPs located in various locations with software to display location of fire / activated device monitoring on the map of the entire facility with zoom capability and Latest Windows 64 bit multitasking software with license, A3 Colour inkjet printer and all accessories. CPU shall be suitable to connect single mode Optic fiber cable and along with required module / converters to be added for OF Cable as required in complete

Supply, installation, testing and commissioning of 8 Way Wago/ Phonix terminal connector in weather proof MS Junction box including painting and all installation materials etc as required.

Supply, installation, testing and commissioning of Addressable UV & IR Flame Detector complete as required and as per specifications.

Supply, Laying testing and commissioning of 4core x 2.5sq.mm copper conductor FRLS insulated armoured cable for interconnecting Main Fire Alarm Control Panel to Fire Alarm Repeater Panels. When the cable is to be laid in ground, the same shall be laid at a depth of 750mm below ground level including excavation in all kind of soil, SDR, refilling of earth after cables are laid, providing protection with sand cushioning at bottom and PCC blocks/ bricks at sides & top and identification tag at both the ends etc., complete.

Supply, Laying testing and commissioning of 6 Core Outdoor Armoured OS2 Single Mode Optical Cable of Size 9/125micro m Outdoor Corrugated Steel tape loose tube Jacket through existing GI/HDPE/ Hume pipe or on cable trays inside the cable duct including all necessary fixing accessories e.g. cable ties, hardware etc. The cable shall be as per the DOT specifications.

Supply and laying of 50mm dia. PLB HDPE Telecommunications Duct as per TEC including suitable jointing kit/ coupler at both ends & providing Nylon/P.P. rope for laying of LAN/ Internet/ OF Cables drawn through HDPE pipes properly at the time of laying pipes, duct shall be smooth outside, free from blisters, shrink hole, scratches & roughness etc. The Inner layer shall be spirally ribbed, duct shall be laid 750mm below ground level excluding excavation in all kind of soil, horizontal drilling, SDR, refilling of earth after HDPE pipes are laid etc., Raw material of the duct shall be PE 63 Grade UV. (Supply and laying of HDPE pipe with accessories without excavation/ civil works).

SUBHEAD - XXII : DG Set:

Supply, installation, Testing and Commissioning of 3 phase and Neutral 415V 4 wire Free Standing Floor mounted MV panel made out of 2mm thick CRCA sheet for main frame and 1.6mm thick for partitions after seven tank process and painting with Epoxy powder coating. The panel shall consist of suitable rating 4P Aluminium busbar (at the rating of 0.8A/Sq.mm) supported with DMC/ SMC barriers and color coded with Heat shrinkable sleeves. The Metering shall be provided as specified. The panel shall have Short circuit withstanding capacity of minimum 50KA and consist of the switchgear as mentioned below. The panel shall be got fabricated from manufacturers with CPRI Test certificate only. The PCC shall have atleast two spare cubicles to suit the highest rating outgoing MCCB. The size of all Panel Mounting Meters shall be 96X96mm. The Panels shall be mounted on U channels including supply and fixing of the same. Every ACB shall be

Incoming : 1250A, 50KA 4pole EDO ACB with micro processor based releases and with 400A 3pole AC3 Contactor link - 2sets Bus bars : 2500A 4P Aluminum busbars-1set Outgoings :2500A 50KA 4pole EDO ACB with micro processor based releases – 1set Metering for Each Incomer : Digital Voltmeter -1 set Digital Ammeter with resin cast CTs - 1set Digital KW Meter - 1set Digital Energy Meter -1set LED type phase indication lamps with individual fuse and toggle switch control -1set Indication Facia for DG Faults/ alarm with Hooter -1set

Supply & installation of 990 Ltrs capacity Fuel tank made out of MS sheet with Inlet/ Outlet connecting pipes, plugs, Drain valve from DG sets to tank and Scale with level monitoring.

Supply & fixing of MS Exhaust Pipe of suitable dia cladded with 50mm thick Glasswool insulation covered with 24SWG Aluminium sheet.

SUBHEAD - XXIII : CCTV System:

Supply Installation testing and commissioning of 3 MP Dome Camera - SITC of 3Mpx Indoor dome 2048 x 1536 at 30fps, Autofocus Motorized remote zoom lens 2.8 - 12mm, H.265, H.264 compression, 50mtr Adaptive IR, 120dB true WDR as per IEC 62676. Minimum Illuminator @F1.4 0.016lux color; 0.007lux Mono, 3D noise filtering, Bi directional Full Duplex Audio, inbuilt mic, 1 Alarm In, 1 Alarm out, 3 independant stream, 8nos of configurable privacy mask, Supported protocol - TCP/IP, Ipv4 & IPv6,UDP/IP, DNS, DDNS,ARP, ICMP, IGMP, RTCP, SFTP, SIP, TLS/TTLS, ARP.802.1x (EAP-MD5, EAPTLS, EAP-TTLS, EAP-PEAP and EAP FAST). Edge based analytics -Object Counting, Adaptive Motion, Object Removal, Motion Detection, Camera Sabotage, Audio Detection, and Directional Motion. Camera shall features of Corridor mode, Mirror mode, having SD card provision of 2TB, Operating temperature -10 to +55deg C,IP64, IK10,Works on PoE, 24 VAC & 12VDC, Power consumption 12W, ONVIF profile S,G & T,Cybersecrutiy Cert:UL/NDAA, CE - EN 55032 (Class A), EN 50130-4, EN 60950-1,FCC (Class A) - 47 CFR Part 15,UL and cUL Listed - UL 60950-1, CAN/CSA-C22.2 No. 60950-1-07, BIS certified.to ruggedized performace camera should meet Shock & Vibration Certifcation:IEC 60068:2-6 and 2-27 The Camera to be provided by OEM should not be complying to GB28181, GB/T28181-2011 standards and there should be no option to activate or deactivate GB/T 28181 standards in the camera web page/Settings. ( Make: Axis/Pelco/Bosch/Avigilon/Mobotix)

Supply INstallation testing and commissioning of 3 MP Bullet Camera - SITC of 3Mpx Indoor dome 2048 x 1536 at 30fps, Autofocus Motorized remote zoom lens 2.8 - 12mm, H.265, H.264 compression, 50mtr Adaptive IR, 120dB true WDR as per IEC 62676. Minimum Illuminator @F1.4 0.016lux color; 0.007lux Mono, 3D noise filtering, Bi directional Full Duplex Audio, inbuilt mic, 1 Alarm In, 1 Alarm out, 3 independant stream, 8nos of configurable privacy mask, Supported protocol - TCP/IP, Ipv4 & IPv6,UDP/IP, DNS, DDNS,ARP, ICMP, IGMP, RTCP, SFTP, SIP, TLS/TTLS, ARP.802.1x (EAP-MD5, EAPTLS, EAP-TTLS, EAP-PEAP and EAP FAST). Edge based analytics -Object Counting, Adaptive Motion, Object Removal, Motion Detection, Camera Sabotage, Audio Detection, and Directional Motion. Camera shall features of Corridor mode, Mirror mode, having SD card provision of 2TB, Operating temperature -10 to +55deg C,IP64, IK10,Works on PoE, 24 VAC & 12VDC, Power consumption 12W, ONVIF profile S,G & T,Cybersecrutiy Cert:UL/NDAA, CE - EN 55032 (Class A), EN 50130-4, EN 60950-1,FCC (Class A) - 47 CFR Part 15,UL and cUL Listed - UL 60950-1, CAN/CSA-C22.2 No. 60950-1-07, BIS certified.to ruggedized performace camera should meet Shock & Vibration Certifcation:IEC 60068:2-6 and 2-27 The Camera to be provided by OEM should not be complying to GB28181, GB/T28181-2011 standards and there should be no option to activate or deactivate GB/T 28181 standards in the camera web page/Settings.( Make: Axis/Pelco/BOSCH/Avigilon/Mobotix)

Supply Installation testing and commissioning of 2 MP PTZ Camera - SITC of 1/2.8", 2Mpx IR PTZ dome 1920 x 1080 at 60fps, Focal length 4.5 - 135mm, Horizontal angle of view: 58.3° (wide) ~ 2.34° (tele); 150mtr Adaptive IR, 100dB WDR,0.1 lux at color, Shutter range: 1 ~ 1/10,000 sec, Electronic image stabilization, Edge based analytics - Motion Detection, Camera Sabotage, BLC, protocol support -IPv4 & Ipv6,802.1x (EAP), TLS1.2, ARP, ICMP, IGMP, DNS, DHCP, TCP/IP. Pan 360deg continuous, Tilt range: +15 to - 90deg, Pan preset speed: 300°/sec; Tilt preset speed: 145°/sec, 256presets, having SD card provision of 2TB, Aluminum construction, 16 configurable privacy masks, Operating temperature -40 to +60deg C, IP66, Type 4X Certification, IK10 Enclosure, Works on (802.3bt), 24 VAC & 48 VDC, ONVIF profile S,G, & T, UL, CE, FCC, BIS certified. With require accessories wall mount, pole bracket etc.. The Camera to be provided by OEM should not be complying to GB28181, GB/T28181-2011 standards and there should be no option to activate or deactivate GB/T 28181 standards in the camera web page/Settings. if required Fabrication work for Pole Mounting arrangement of PTZ camera ( Make: Pelco/BOSCH/Avigilon/Mobotix)

Supply INstallation testing and commissioning of 64 Chanel NVR - Supply installation Testing and Commissioing of Video Management Recording servers .it should supports upto 64 cameras for future upgradation .It should have Intel® Core i5- 9500 or better with 16 GB DDR4 ECC RAM or better. It should run on Windows® 10 IoT Enterprise 64-bit (LTSB) or latest.It should have M2. NVMe 256 GB for operating system.Shall support Dynamic Host Communication Protocol ( DHCP ) and Network Time Syncronisation Protocol ( NTP ) functionality. It shall have Mapping function. it should have in built plugins to integrate third party systems. Each Box should have Thoughput should be 200 Mbps. ,*Video Outputs- 4x Mini Display port 1.4 ,*VMS Should support ONVIF S,G & T ,Should have NVIDIA Quadro P620 (2 GB memory) ,Should have 1xGigabit Ethernet (1000Base-T) ports,1x 10 Gigabit Ethernet (10 G Base-T) ( Make: Pelco/BOSCH/Avigilon/Mobotix)

Supply , Installation,testing and commissioning of 24 port L3 Managed core Switch - 24 x 100/1G , 4 x 1G/10G SFP+ Ports , 4 x 10/25G SFP28 Ports with a slot for optional module, Redundant Hot Swappable Power Supply - AC/DC , Virtual stack Upto 8 Switch , 4GB or better, 16 GB Flash, SFP Should be from the same OEM . , 960Gbs or better , 540 Mpps or better , support for 64k Mac addess, 144k Ipv4 and 72 Ipv6 routes , Support for Egress rate limiting, Eight egress queues per port, IEEE 802.1Q, 802.3x, DiffServ, Jumbo frame Ipv4/ IPv6, MACSEC on 10G uplink ports , IGMP Snooping V1, V2, V3, MLD, PIM SM/PIMSSM/PIM-DM/PIM-Bidirectional, DVMRP, OSPF, RIP, BGP, IS-IS, ITU-T G.8032, IEEE 802.1s, IEEE 802.3ad/802.1AX Link Aggregation Control Protocol (LACP), Ipv4/Ipv6, DHCP Option 82, BPDU, STP Root

Guard, SIP detection, SPB or MPLS, IEEE 802.1ae, MIB, NTP, Macsec , SNMP V1,V2,V3, Web GUI, CLI, USB or equivalentmemory card, IP v6 management feature on openstandards, IEEE 802.1ag, TDM or equivalent standards , Should support Access Control Lists (ACLs), DHCP snooping, IEEE802.1x based port authentication, RADIUS/ TACACS+, SSL, SSH, port mirroring,NTP, IEEE 1588, AES, Syslog, MD5, LLDP-MED , IEEE802.1q, IEEE802.1d, IEEE802.1s, IEEE802.1w, ITU-T G.8032 ring resilience/ring protection, VRRP , Working memory/ Recovery memory , '0 to 45Deg ,CE, EN 55032, RoHS US UL 60950, CSA22.2 FIPS 140-2, EAL2 or equivalentEN 60825-1/2 Laser (MAKE:ALCATEL/ CISCO/BROCADE)

Supply Installation Testing & Commissioning of Switch 24 Port POE Giga Port Switch - GigE fixed chassis 24 RJ-45 PoE 10/100/1G BaseT, 2 fixed RJ45/SFP combo (1G), 2 fixed SFP+ (1G) uplink or 10G stacking ports. 1RU size, internal 600W AC power supply. Includes United States power cord, guides, and 19" rack mount hardware. ALCATEL/ CISCO/BROCADE

Supply INstallation testing and commissioning of VMS - Software - Supply installation Testing and Commissioing of Video Management Softwarwe VMS should have smart motion Search for server side motion detection and quick retrieval of events *Edge Storage Auto Gap Fill functionality detects when a gap in local camera recording occurs, and automatically downloads video and audio (if present) to fill the gap *web based client allows viewing and exporting video without installing any software.*Imports users and roles from existing LDAP servers to reduce administrative overhead, and enables single sign-on (SSO) *Capable of listening for ASCII commands on a serial and Ethernet port simultaneously *Supports shared displays so operators can send video to surveillance personnel who need it most *Check on VMS and camera health using SNMP *Supports IPv4 and IPv6 cameras *Enables and supports Risk Management Framework (RMF) *TLS-based encryption over HTTPS *Extensible through mapping and plugins, including video information overlays and license plate recognition *should include feature, which is capable of polling for alarms from devices and performing specified actions when an alarm state change occurs *Incorporates FIPS 140-2 validated cryptographic modules. To ensure seamless deep integration VMS should be of same camera OEM ( Make: Pelco/BOSCH/Avigilon/Mobotix)

Supply, Installation, Testing & Commissioning of 6TB HD

Supply, Installation , testing and commissioning of 12 V SMPS DC Power Supply Unit, highly regulated and spikes free terminal voltage and heavy sourcing current for regulated terminal voltage

Supply, Installation , testing and commissioning of 55 inches UHD 3840 x 2160 (16:9) Direct-lit LED Display with brightness of 500 nits, viewing angle of 178° h/v. Display should be supplied with necessary mounting bracket as required Make :Barco, Christie, LG Samsung

Supply, Installation, testing and commissioning of UTP 4 pair 23 AWG CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 4 Pair CAT6 Unshielded, Twisted Pair (U/UTP) Cable 305 mtr per Box. Blue/Orange/White/Green in colour conforming to the following standards like ANSI EIA/TIA 568 C.2, EN50173, IEC 11801 3rd ED, frequency tested upto 700Mhz with Third Party Certificate etc. Cable Dia 6.1 ± 0.3, Cross-member (+) fluted Spine/isolator for uniform separation for all pairs. Make: Systimax/Panduit/Siemon/Legrand).

Supply, Installation, testing and commissioning of Cat6 Tool less Information outlet for Data & Voice. Cat6 U/UTP RJ45 socket with built in crimping mechanism with capability of retermination without refreshing the wires. Toolless RJ45 Information outlet with insertion cycle (in & out) should be 2500 times (I/O) along with front side Label holder and transparent shutter. The Information Outlet connector shall be of gold/nickel, thickness of gold > 0.8 μm. The connectors shall be compatible as per IEEE 802.3bt standard for POE++ application (Make : Systimax/Panduit/Siemon/Legrand).

Supply , Installation , Testing and commissioning of CAT 6 jack panel

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); Memory: 4GB, NON-ECC, 1600MHZ; RAM: 4GB (1x4GB) Non-ECC DDR3 1600MHz SDRAM Memory; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 20" TFT Monitor; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit.

Supply and laying of 25mm dia, 2.00mm thikness heavy duty FRLS PVC conduit concealed in wall / ceiling / floor including all accessories such as Junction boxes, conduit bends, etc. completed as required.

Supply, installation, testing and commisioning of 19" rack 32 U floor mount rack with all standard aceessories that include cable manager, fan, power bar with sockets etc. as per requirement

Supply, installation, testing and commisioning of 19" rack 9 U wall mount rack with all standard aceessories that include cable manager, fan, power bar with sockets etc. as per requirement

CAT6 UTP 24 AWG Patch Cord - 1 mtr with cross separator , Manufactured from stranded wires for longer flex-life , Minimum length of 1m, and maximum length of 5m Conforming to the following standards like EN 50173, ISO/IEC 60603-7 & 11801/IEC 60332-1, UL VW-1 with tensile strength >50N, number of insertion is 750(Make : Systimax/Panduit/Siemon/Legrand

Supply, Installation, testing and commissioning of 24 port Cat 6 19" Modular Toolless Patch Panel (loaded) enable all possible combinations of the various types of cable (UTP, FTP, SFTP) mounted on the same panel by using various toolless connector blocks/modules. Have a metal structure enabling them to be durably fixed to the uprights of the 19” chassis and assuring automatic grounding between toolless RJ-45 connectors, the panel, and the 19” uprights of the enclosure. Include rear cable support with plastic cable guides to hold cable without need for cable ties. Include quick mounting system to mount the panel into the 19” rails without use of cage-nuts. These may be used to secure the connections of wifi access points, IP cameras, servers, or other critical devices. Front Removal IO's option for maintenance and trouble shooting with 6 Different Colours Labels for Labelling & Identification of Individual Ports. Tested and guaranteed under dual circuit IEEE PoE++ up to 90W for up to 2500 on-load connections / disconnections. (Make :Systimax/Panduit/Siemon/Legrand)

SUBHEAD - XXIV : External Power Supply & Area Lighting:

Supply of following size 1.1KV grade XLPE insulated armoured aluminium/copper conductor cables. When the cable is to be laid in ground, the same shall be laid at a depth of 750mm below ground level including excavation in all kind of soil, SDR, refilling of earth after cables are laid, providing protection with sand cushioning at bottom and PCC blocks/ bricks at sides & top, cable route markers at every 15mtr. interval also at the turnings & joints and identification tag at both the ends etc., complete. The cable shall conform to IS: 7098 Part 1/1988.

a) 3.5C X 300 Sq.mm A2XFY

b) 3.5C X 240 Sq.mm A2XFY

c) 3.5C X 185 Sq.mm A2XFY

d) 3.5C X 120 Sq.mm A2XFY

e) 3.5C X 95 Sq.mm A2XFY

f) 3.5C X 70 Sq.mm A2XFY

g) 3.5C X 50 Sq.mm A2XFY

h) 4C X 25 Sq.mm A2XFY

i) 4Core 16 sq.mm A2XFY

j) 4Core 10 sq.mm A2XFY

k) 3Core 4 sq.mm 2XWY

l) 3C X 6 sq. mm. 2XWY

m) 6C X 2.5 sq.mm 2XWY

n) 19C X 2.5 sq.mm 2XWY

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

a) Upto 35 Sq.mm

b) Above 35 Sq.mm. and upto 95 Sq.mm.

c) Above 95 Sq.mm. and upto 185 Sq.mm.

d) Above 185 Sq.mm. and upto 400 Sq.mm.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

a) Upto 35 Sq.mm.

b) Above 35 Sq.mm. and upto 95 Sq.mm.

c) Above 95 Sq.mm. and upto 185 Sq.mm.

d) Above 185 Sq.mm. and upto 400 Sq.mm.

CABLE END TERMINATIONS Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

a) 3.5C X 300 Sq.mm

b) 3.5C X 240 Sq.mm

c) 3.5C X 185 Sq.mm

d) 3.5C X 120 Sq.mm

e) 3.5C X 95 Sq.mm

f) 3.5C X 70 Sq.mm

g) 3.5C X 50 Sq.mm

h) 4C X 25 Sq.mm

i) 4Core 16 sq.mm

j) 4Core 10 sq.mm

k) 3/4C X 4/6 sq. mm. (Copper)

l) 3/4C X 2.5 sq. mm. (Copper)

m) 19C X 2.5 sq. mm. (Copper)

Supply, erection, testing and commissioning of Garden Lighting Pole of 4.50 Mtr. high (above ground), 100mm bottom dia and 3mm thick including 45W LED Post Top Latern Light fitting, designed Galvanised pole shall be structurally sound, built-in control box with service door including lock and safety chain consisting suitable connector for termination box including necessary fixing arrangement, the control gear tray is prewired with suitable rating of MCB, terminal connectors for loop-in loop-out arrangement, Pole Finish : Coated with epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint, Installation : Surface mounted with 10mm thick GI base plate and fitted on a pre-formed foundation, J type foundation nut-bolts, suitable PVC/ HDPE sleeves for incoming and outgoing cable,

including earthing arrangement, excavation & back filling, bedding, PCC foundations 1:2:4, coping, PCC Pedestal, The wiring from Junction box to Light fixture shall be carried out with 3core 1.5sq.mm multistranded copper flexible cable. Suitable bracket/ reducer with accessories shall be provided to suit the fixture mounting.

The pole shall be fixed with 1no. 45W (-5% without affecting lumens output) LED post top lantern light fitting, lumens output greater than or equal to 4950 lumens, integrated design, mounting on pole. Post top fixture made of die-cast aluminum spigot for mounting LED driver and spun aluminum canopy which is painted white inside and epoxy powder coated matt black finish. High quality polycarbonate cover diffuser. Totally weather proof (IP-65 protection), bottom entry type. Prewired with LED driver and suitable for operation on 240V, 50Hz single phase ac supply.

The driver shall be constant current/ constant voltage output, power factor more than 0.95, THD less than 10%, 5kV over voltage protection/ surge protection and radio frequency noise suppression circuit as per IEC 61000-4-5, Driver safety requirement standards: IS 15885-2-13, Driver performance standards : IS 16104. Short circuit & over load protection auto recovery. Certification: LM 79 for LED luminaire and LM 80 for LED source. The CRI shall be greater than 70%. Test certificates to be submitted. The Lumens output of the system/ luminaire shall be greater than 110 Lumens/ Watt.

Supply and erection of hot dip GI octagonal street light pole of 8 Mtr. Long, bottom dia – 130mm, top dia – 70mm, hot dip galvanized 80-100 microns, thickness 3 mm, 300x300x12mm GI base plate, J type foundation nut-bolts, earthing studs/terminals, 1.5 Mtr out reach single arm bracket, built-in control box with service door including lock and safety chain consisting suitable connector for termination of 3.5C- 35 sq. mm aluminium cable (2 terminations : 1 Incoming and 1 Outgoing) including necessary fixing arrangement, the control gear tray is prewired with suitable rating of MCB, terminal connectors for loop-in loop-out arrangement,

2nos 40mm dia HDPE Pipes of 1.5mtr. Long for incoming and outgoing cables, including earthing arrangement, excavation & back filling, bedding, PCC foundations 1:2:4, coping, PCC Pedestal complete as required. The wiring from Junction box to Light fixture shall be carried out with 3core 2.5sq.mm multistranded copper conductor cable. Installation: Surface mounted with GI base plate and fitted on a pre-formed foundation.

The pole shall be fixed with 1no. 90W (-5% without affecting lumens output) LED Street light fittings,lumens output greater than or equal to 11250 lumens, integrated design, mounting on single pole arm. Pressure die-cast aluminium alloy for housing (heat sink) for effective thermal management, corrosion resistant integral model, totally weather proof (IP-65 protection), side entry type. Prewired with LED driver and suitable for operation on 240V, 50Hz single phase ac supply.

The driver shall be constant current/ constant voltage output, power factor more than 0.95, THD less than 10%, 10kV over voltage protection/ surge protection and radio frequency noise suppression circuit as per IEC 61000-4-5 housed within the fixture, Driver safety requirement standards: IS 15885-2-13, Driver performance standards : IS 16104. Short circuit & over load protection auto recovery. Certification: LM 79 for LED luminaire and LM 80 for LED source. The CRI shall be greater than 70%. Test certificates to be submitted. The Lumens output of the system/ luminaire shall be greater than or equal to 125 Lumens/ Watt.

Supply, erection, testing and commissioning of 40W (-5% without affecting lumens output) LED street light fitting, weatherproof terminal/ junction box (IP-65) similar to Make : Hensel, Cat No. KF 0402 B/ equivalent including terminal connectors for loop-in loop-out arrangement, wiring from terminal box to the fixture with 3 core 1.5sq.mm multi strand copper flexible cable, wall mounted 2.0M long pole arm (class B GI pipe of suitable size for fixing the light fitting) including necessary fixing & mounting accessories, complete as required. The LED light fittings shall have lumens output greater than or equal to 5,000 lumens, integrated design, mounting on GI pipe of suitable dia, pressure die-cast aluminium alloy for housing (heat sink) for effective thermal management, corrosion resistant integral model, totally weather

proof (IP-65 protection), side entry type. Prewired with LED driver and suitable for operation on 240V, 50Hz single phase ac supply. The driver shall be constant current/ constant voltage output, power factor more than 0.95, THD less than 10%, 10kV over voltage protection/ surge protection and radio frequency noise suppression circuit as per IEC 61000-4-5 housed within the fixture, Driver safety requirement standards: IS 15885-2-13, Driver performance standards : IS 16104. Short circuit & over load protection auto recovery. Certification: LM 79 for LED luminaire and LM 80 for LED source. The CRI shall be greater than 70%. Test certificates to be submitted. The Lumens output of the system/ luminaire shall be greater than or equal to 125 Lumens/ Watt.

Supply, Installation, Testing & commissioning of outdoor type (IP 65) Bollard Light 180 mm overall dia, 800 mm height, Housing & fixation Material aluminium, optical cover-Polycarbonate, 10 W LED Light with 34 lumen / watt, warm white, Base Plate,stainless steel screw, corrossion & UV resistant coat, including suitable size of CC foundation, grouting bolt, plastering etc as complete as required.

Supply, installation, testing and commissioning of digital programmable timer switches similar to Make : Legrand, Cat No.: 4126 29/ equivalent, in factory made MS enclosure outdoor type, fixing accessories hardware on wall etc. complete.

Supply, installation, testing and commissioning of outdoor and weather proof type junction box for 16/25/35 sq. mm aluminium/ copper cables including suitable rating of connectors, mounting stand, hardware and fixing accessories. Junction box similar to Make : Hensel, Cat No. KF 9355/ equivalent, complete as required.

Supply, fixing, testing & commissioning of 2x12W Aviation Lamp including 3 Mtr long 50mm dia class B GI pipe with two coats of primer redoxide and two coats zinc chromate aluminium paint, including earthing arrangement, PCC foundations 1:2:4, PCC Pedestal upto 450mm, terminal box with SP MCB, 3C x 2.5 sqmm un-armoured flexible cable from junction box to light fitting and end termination of same at both sides by providing necessary gland & lugs, hardware and accessories for fixing of Aviation Lamp on GI pole etc. complete, as required. Junction box similar to Make : Hensel, Cat No. KF 0402 B/ equivalent, complete as required.

SUB HEAD -XXV : Lift Work

Supply, erection, testing and commissioning of electic 15 Passenger capacity Machine less lift of 1.0 Ton. capacity to serve Ground Floor & First floors ( total two stops & two openings) with a total travelling length of approximately 12.0 mtrs. including elevator, VVVF drive, machines, controllers, car body, car guides, landing doors, counterweights, main suspension steel rope, cabling, safety device and governer, automatic sliding doors for car and landing hoist way with full height IR sensor, buffers for car and accessories including intermediate supporting channels/ brackets for car guides with all allied works and scaffolding etc. and supply, erection, testing and commissioning of automatic rescue device (ARD) system operating on 4x12 V - 24 AH dry maintenance free batteries with 10 second actuation time and automatic switch over facility including all neccessary cables and termination etc. complete. Make - Otis , Kone, Schindler

CAPACITY (kgs) : 1020 Kg, 15 persons. SPEED (mps) : 1 mps RISE (m) : 12 m CONTROLLER TYPE : ACD3-MRL DRIVE : VF Regenerative (Closed Loop) POWER SUPPLY : 400/415 Volts (3 Phase AC) OPERATION : Full collective operation CAR GROUP : One car (simplex) MACHINE : PM Gearless (Located in shaft on top of guide rails) TRACTION MEDIA : Flat Coated Steel Belt

CAR FINISH : • Rear Mid Panel = Stainless Steel #4(Hairline) • Rear Corner Panels = Stainless Steel #4(Hairline) • Side Mid Panels = Stainless Steel #4(Hairline) • Side Corner Panels = Stainless Steel #4(Hairline) • Front Panels = Stainless Steel #4(Hairline) FALSE CEILING TYPE : CD-41 FLASE CEILING FINISH : Stainless Steel #4(Hairline) VENTILLATION : Cross flow fan HAND RAILS : Stainless Steel Mirror Finish Handrails on rear car panels FLOORING : GRANAMITE CAR DOOR FINISH : Stainless Steel #4(Hairline) LANDING DOORS FINISH : Stainless Steel #4(Hairline) FIRE RATED DOORS : Fire rating-120mins FIRE RATED DOORS : Fire rating-120mins

CAR DIMENSIONS (W x D x H - mm) : 1000 mm W x 2400 mm D x 2200 mm D CAR & HOISTWAY DOOR TYPE : Central opening (CO) doors DOOR OPENING (W x H - mm) : 900 mm W x 2000 mm H DOOR OPERATOR : DC Door Operator COP : COP for stops <= 12 (950mm) in Stainless Steel #4(Hairline) CAR POSITION INDICATOR : Monochrome LCD-Blue Background & White font Dot matrix (LED) Scrolling Display HALL FIXTURES : O2000 Pan Type Fixture , HALL FIXTURE FACE PLATE : Stainless Steel #4(Hairline) HALL BUTTON ARRANGEMENT : LCD Monochrome type

STANDARD FEATURES : Anti-nuisance Car Call Protection Independent Service (for Duplex only) Overload Device Nudging Emergency Car Light Unit Infrared Curtain Door Protection Door Time Protection Emergency Alarm Button Extra Door Time of Lobby & Parking Door Open/Close Button Manual Rescue Operation Belt Inspection Drive Auto Fan Cut Off OPTIONS INCLUDED : Emergency Firemen’s Service, Automatic Rescue operatio

Supply, erection, testing and commissioning of electic passenger cum goods lift (Machine less) of 1.0 Ton. capacity to serve Ground Floor ( two opening ) & First floors ( one opening ) ( total two stops & three openings) with a total travelling length of approximately 12.0 mtrs. including elevator, VVVF drive, machines, controllers, car body, car guides, landing doors, counterweights, main suspension steel rope, cabling, safety device and governer, automatic sliding doors for car and landing hoist way with full height IR sensor, buffers for car and accessories including intermediate supporting channels/ brackets for car guides with all allied works and scaffolding etc. and supply, erection, testing and commissioning of automatic rescue device (ARD) system operating on 4x12 V - 24 AH dry maintenance free batteries with 10 second actuation time and automatic switch over facility including all neccessary cables and termination etc. complete. Make - Otis , Kone, Schindler

CAPACITY (kgs) : 1020 Kg SPEED (mps) : 1 mps RISE (m) : 12 m CONTROLLER TYPE : ACD3-MRL DRIVE : VF Regenerative (Closed Loop) POWER SUPPLY : 400/415 Volts (3 Phase AC) OPERATION : Full collective operation CAR GROUP : One car (simplex) MACHINE : PM Gearless (Located in shaft on top of guide rails) TRACTION MEDIA : Flat Coated Steel Belt

CAR DIMENSIONS (W x D x H - mm) : 1000 mm W x 2400 mm D x 2200 mm D CAR & HOISTWAY DOOR TYPE : Central opening (CO) doors DOOR OPENING (W x H - mm) : 900 mm W x 2000 mm H DOOR OPERATOR : DC Door Operator COP : COP for stops <= 12 (950mm) in Stainless Steel #4(Hairline) CAR POSITION INDICATOR : Monochrome LCD-Blue Background & White font Dot matrix (LED) Scrolling Display HALL FIXTURES : O2000 Pan Type Fixture , HALL FIXTURE FACE PLATE : Stainless Steel #4(Hairline) HALL BUTTON ARRANGEMENT : LCD Monochrome type

CAR FINISH : • Rear Mid Panel = Stainless Steel #4(Hairline) • Rear Corner Panels = Stainless Steel #4(Hairline) • Side Mid Panels = Stainless Steel #4(Hairline) • Side Corner Panels = Stainless Steel #4(Hairline) • Front Panels = Stainless Steel #4(Hairline) FALSE CEILING TYPE : CD-41 FLASE CEILING FINISH : Stainless Steel #4(Hairline) VENTILLATION : Cross flow fan HAND RAILS : Stainless Steel Mirror Finish Handrails on rear car panels FLOORING : GRANAMITE CAR DOOR FINISH : Stainless Steel #4(Hairline) LANDING DOORS FINISH : Stainless Steel #4(Hairline) FIRE RATED DOORS : Fire rating-120mins

STANDARD FEATURES : Anti-nuisance Car Call Protection Independent Service (for Duplex only) Overload Device Nudging Emergency Car Light Unit Infrared Curtain Door Protection Door Time Protection Emergency Alarm Button Extra Door Time of Lobby & Parking Door Open/Close Button Manual Rescue Operation Belt Inspection Drive Auto Fan Cut Off OPTIONS INCLUDED : Emergency Firemen’s Service, Automatic Rescue operatio

SUBHEAD - XXVI : EOT Crane

Design, Manufacturing, Supplying, Erection, Testing & commissioning of double girder, non flame proof EOT crane 30 Tonne capacity, conforming to the standard given in IS 807,3177 and other relevant IS standards of the latest revisions etc. all complete with VVF, Drive Class -II Indoor Duty, Span 30Metre Bay Length 60Metre, Lift- 9 Metre with the followwing speed Main Hoist- 2.5 Mtrs/Min Cross Traver - 6Mtrs / Min Lang Travel - 12 Mtrs / Min

Duty: Indoor, Span: 30m, Bay length: 60m, Lift: 9 m

Supplying, Erection, Testing & Commissioning of for drag chain type of current collection system complete with drag chain with vertical separators, mounting brackets with tie wrap plates, support plates, trough with glide bar including mounting kit, along with cable from switch and with all necessary fixtures.

Supplying, Erection, Testing & Commissioning of Gantry Rails section 120Lb of prime material in length of 10m and above complete with mounting arrangement and fixing hardware etc., complete over the bay length to match the span of the crane within the permissible accuracy levels for span in height variation as per the QA plan.

SUBHEAD - XXVII : Air Conditioning Work

VRV/VRFSystem: Supply, Installation, testing and commissioning of AIR COOLED & INVERTER BASED VARIABLE REFRIGERANT VOLUME / VARIABLE REFRIGERANT FLOW MODULAR TYPE AIR CONDITIONING SYSTEM with R410A suitable for 415 ± 10% , 50 Hz. The unit shall consist of indoor units and external condensing units and other accessaries as listed below complete in all respects as under

Outdoor Unit SITC Modular type outdoor units equipped with highly efficient Heat Pump inverter type scroll compressor(s) with special precoated heat exchanger, low noise condenser fan housed in compact housing duly powder coated. Outdoor units shall have both cooling & heat pump mode, and environmet friendly refrigerant R-410A.The C.O.P shall be confirmed at full and part load at.Complete with M.S mounting stand of approved design for outdoor unit.Nitogen Flushing before gas charging.Pressure testing should be done after installation.Anti corrosive coating should be done at site.

24 HP (Actual) at Site Conditions

20 HP (Actual) at Site Conditions

18 HP (Actual) at Site Conditions

16 HP (Actual) at Site Conditions

14 HP (Actual) at Site Conditions

10 HP (Actual) at Site Conditions

8 HP (Actual) at Site Conditions

Indoor Units: Supply,Installation, testing and commissioning of both interconnected with copper refrigerant & drain pipe of required length, insulation, full charge of refrigerant gas and oil, M.S. base frame duly primered & painted, supports etc. complete as per specifications and drawings.

Celing Mounted Duct Type: SITC of Imported Air Cooled VRV/VRF Ceiling mounted built-in type/ ductable type Indoor units equipped with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, electronic expansion valve, outer cabinet, drain pan, insulation, pipe connections,control and power panel with corded remote control etc. etc. of various capacities as per specifications and drawings.

SITC of Imported Air Cooled VRV/VRF HI-Wall Type Indoor units equipped with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, electronic expansion valve, outer cabinet, drain pan, insulation, pipe connections,control and power panel with Cordless remote control etc. of various capacities as per specifications and drawings.

Split HI-Wall Type Supplying, fixing, testing and commissioning of Hi Wall type Heating and Cooling Type split air-conditioning unit suitable to operate from 230±10% volt, 50 Hz, 1 phase power supply, with air-cooled evaporator with coil, fan, and fan motor, air-cooled condenser with hermetically sealed rotery / reciprocating compressor condenser coil, propeller fans controls, control panel, Including control wiring, necessary power cable, M.S. frame duly painted to locate Outdoor Unit etc. The Unit should be atleast 3 Star rated. The Refrigerant pipe size and gas quantity should suit to the copper pipe length at actual.Upto 15 metre copper Pipe with cable tray shall include in the quote. 2.0 TR

Installation &Allied Works: Y-joints & header etc above complete as per specification and drawings.

Supply,Installation, testing and commissioning of Centralised remote controllers for operation & status monitoring of VRV/VRF indoor units.

Refrigerant Piping: Supply,installation,testing and commissioning of Interconnecting non exposed refrigerant pipe work with (19mm/13 mm thick) , Class 'O', k value-0.035 w/mk minimum, Density not less than 55 Kg/cu.m closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger & clamps

41.3 mm O.D. (insulation : 19 mm)

34.9 mm O.D. (insulation : 19 mm)

28.6 mm O.D. (insulation : 19 mm)

22.2 mm O.D. (insulation : 13 mm)

19.1 mm O.D. (insulation : 13 mm)

15.9 mm O.D. (insulation : 13 mm)

12.7 mm O.D. (insulation : 13 mm)

9.5 mm O.D. (insulation : 13 mm)

Supply,installation,testing and commissioning of Interconnecting exposed refrigerant pipe work with (19mm thick) , Class 'O', k value-0.035 w/mk minimum, Density not less than 55 Kg/cu.m closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping inside the room shall be properly supported with MS hanger & clamps Refrigerant piping will be coated with three layers of feviprotekt (only pidilite) weather coating.

41.3 mm O.D. (insulation : 19 mm)

28.6 mm O.D. (insulation : 19 mm)

19.1 mm O.D. (insulation : 13 mm)

15.9 mm O.D. (insulation : 13 mm)

Fresh air unit (for VRV): Supplying, installing, testing and commissioning of factory built Floor Mounted double skin type air handling units made of 40 mm thick panels consisting of pre plasticized G.I casing made of thickness 0.6 mm outside layer and G.I sheet of thickness 0.6 mm inside layer with polyurethane foam (PUF) insulation of density 42 kg/m3 factory injected between them by injection moulding machine, complete with Direct Driven Backward Curved Aerofoil Plug Type Fans with VFD's with aluminium finned copper tubes (tubes thickness not less than 0.3 mm),filter sections with 50 mm thick washable synthetic type pre filter having

efficiency 90% down to 10 micron,fine filters having efficiency 99% down to 5 micron along with The AHU shall be equiped with factory fitted Adavnced Oxidation plasma cell (AOP) based on nanoX technology certified by CCMB lab/ ICMR lab to kill covid-19 by greater than 99% within 45 mins. The product shall have CE & RoHS Certiffication,backward curved plug fan with aerofoil design blades with TEFC (IEE-3) suitable for VFD operation at 415 ± 10% volts, 50 Hz, 3 phase, A.C supply, mixing box ,drain connections with drain valve, Flexible connection,stainless steel drain pan, necessary vibration isolation arrangement etc, arrangement etc. TP isolator with MS enclosure box should be Provided. etc, complete as per specifications of following capacities: The fan static pressure shall be 80 mm WC static.

20 TR / 4000 cfm with 6 Rows DX Cooling Coil

8.5 TR / 1700 cfm with 6 Rows DX Cooling Coil

6 TR / 1200 cfm with 6 Rows DX Cooling Coil

Ventilation: Inline Fans : Supplying, Installing, Testing and Commissioning of Inline fans complete with motor, supporting frame, gravity louvres,etc. as per drawings and specifications. 700 CFM ,. @ 15mm Static.

Drain Piping:Supply,installation,testing and commissioning of rigid PVC piping complete with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell nitrile rubber class ‘O’ . Providng and fixing pipes with all necessary fittings, supports and insulation.

Ducting: Supply, fabrication, installation, balancing and commissioning of factory fabricated GI sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings of following gauges as per SMACNA standard:-

Thickness 24 G sheet (0.68mm)

Thickness22 G sheet(0.80mm)

Duct Insulation- Supply, installation, testing of thermal insulation of supply air ducting with closed cell Nitrile Rubber with prelaminated Aluminium foil on one side having a low stable k value of 0.035 k.cal/hr.m at 10.C and minimum density of 40-55 ± 3 kg/cum.The R.value should be as per ECBC Code. 19 mm thick

Grilles/Diffusers: Supply,installation, testing and commissioning supply and return air grilles/ diffusers as per specifications and drawings including fixing frame of G.I./wooden in false ceiling/walls.

Aluminium supply air grill with VCD(150mm wide)

Aluminium return/exhaust air diffuser without VCD

Aluminium Supply air Diffuser with VCD

Aluminium return air grill without VCD(150mm wide)

Aluminium volume control damper

Control & Transmission Wiring: Supply,installation,testing and commisioning of control cum transmission wiring of 2 core x 1.5 sqmm unarmoured copper in 25 MM heavy duty PVC conduits between indoor and out door unit & outdoor units to central remotes controllers.

A.C. Panel-DESIGN CENTER (For VRV/VRF) Supplying, assembling, erecting, connecting, testing and commissioning Outdoor type of dust, damp and vermin proof free floor standing factory built sheet steel enclosed non-drawout modular type Panel fabricated out of suitable sized angle iron and flats, base channel and covered with 2.0mm thick PCRC sheet, duly painted complete with earth bus, aluminium bus bar, numbering & sign writing, interconnection & including the cost of connection through bus bar / copper conductor flexible connection with all accessories, rotary handles,phase barriers etc. complete as shown in drawing & as per specifications and mounted with the followings etc. complete as required. (All the starters should have NO/ NC contacts for remote/ fire control facility etc. complete).

A.C. Panel-2 LAUNCHER BAY (For VRV/VRF) Supplying, assembling, erecting, connecting, testing and commissioning Outdoor type of dust, damp and vermin proof free floor standing factory built sheet steel enclosed non-drawout modular type Panel fabricated out of suitable sized angle iron and flats, base channel and covered with 2.0mm thick PCRC sheet, duly painted complete with earth bus, aluminium bus bar, numbering & sign writing, interconnection & including the cost of connection through bus bar / copper conductor flexible connection with all accessories, rotary handles,phase barriers etc. complete as shown in drawing & as per specifications and mounted with the followings etc. complete as required. (All the starters should have NO/ NC contacts for remote/ fire control facility etc. complete).

Weather Proof isolators: Supply, installation, testing and commissioning of out door weather proof switch box of continuous welded construction, fabricated out of 2 mm thick G.I. sheet complete with water tight gasket with front openable and lockable door including earthing, painting, glands, danger boards etc. suitable for mounting on wall with M.S. angle iron frame of size 40x40x6 mm consisting of relevant I.S. specifications and drawings. Weather proof box with MCCBs of suitable ratings near the outdoor units for isolations for VRV Outdoor Units.(63 Amps)

Electrical cable: Supply of PVC insulated armoured Copper conductor cables of 1.1 Kv grade 4 core - 10 mm2

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. 4 core - 10 mm2

Termination: Supplying and making end termination with brass compression gland and Copper lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 core - 10 mm2

AOP Cell -Supply, installation, testing and commissioning of duct mounted air purification system/ cell based Adavnced Oxidation plasma cell (AOP) based on nanoX technology certified by CCMB lab/ ICMR lab to kill covid-19 by greater than 99% within 45 mins. The product shall have CE & RoHS Certiffication,with complete electrical accessories etc. Upto 2700 CFM

KMV PROJECTS LIMITED

QUICK BUILDERS

NIMMA NARAYAN ENGINEERS & CONTRACTORS

SHRI GURMUKHDAS CONTRACTORS PVT. LTD.

RIC Projects Pvt. Ltd.

Inderjit Mehta Constructions Private Limited

Vishal Infrastructure Ltd

Surendra Infrastructure Pvt. Ltd.

RMS CONSTRUCTION PVT. LTD.