Providing furniture and fixture of Incubation centre on top floor of Veg processing Hall and bakery block at main campus Nauni, Distt. Solan.

Amount

a)Providing and fixing Table Top Work station having size 1050Lx600Dx750/1200H table top partition with separator 52 mm thick It shall be fabricated out of 25mm thick prelaminated particle board of Interior grade as per IS:12823 The top shall have straight edging with PvC edge band 1.00 mm-2.00mm from front, rear side and Gable end side.The top shall be supported by a frame fabricated out of MS bracket of 14 gauge CRCA sheet (black powder coated finish) for additional strength. i)Partition Systems: Providing and fixing of Frame & Tile System of 60mm thick of 1200mm high factory made finely tolerance partition. The partitions framework shall have horizontal and vertical anodized Aluminum sections of 1.2 to 1.5mm thickness. The frame work is joined together horizontally and vertically with help of aluminum die cast connectors of 5 mm thickness. Connector are fitted with A pole with the help of M6x16 pan-head machine screw and washer. The corner & tops are concealed by post cover which are of different anodized aluminum profiles All 2way,3way and 4 ways junction is covered with Die cast aluminum caps.

ii)Wire Management The caps rectangular slots for wires on the upright is 60mmhigh by 23mm width ,1 no at the bottom and 6 nos at the intermediate level where in each slot can allow 9 power cable of dia 10 or 32 data cable of dia 6. The bottom horizontal would also have 2 slots for carrying wires, which are of size 60mm(L)) x23mm(W) for wire carrying Raceways of 120mm high made up of anodized aluminum is provided at skirting and above/below the worktop. iii)Keyboard pull out tray of made of 1.2 mm thick CRCA steel duly powder coated, of minimum thickness 50 micron, with metallic roller slides on both sides on Telescopic mechanism and shall be fixed to the bottom of worktop surface with the help of screws. The size of Keyboard tray is 240mm x 484mm and shall be suitable to accommodate keyboards of standard sizes iv)CPU Trolly of size 250x250x234mm (ht) made of 0.7mm thick CRCA steel sheet, duly powder coated in colour of approved shade with 50mm dia castors to provide mobility. The width of CPU should be adjustable complete in all respect as per satisfaction of Engineer-in-charge.

b)Providing and fixing Table Top Work station having size 900Lx600Dx750/1200H table top partition with separator 52 mm thick It shall be fabricated out of 25mm thick graminated particle board of Interior grade as per IS 12823 The top shall have straight edging with PVC edge band 1.00 mm-2.00 mm from frant , rear side and Gabte end side The top shall be supported by a frame fabricated out of MS bracket of 14 gauge CRCA sheet (black powder coated finish) for additional strength. Partition Systems: Providing and fixing of Frame & Tile System of 60mm thick of 1200mm high factory made finely tolerance partition. The partitions framework shall have horizontal and vertical anodized Aluminum sections of 1.2 to 1.5mm thickness. The frame work is joined together horizontally and vertically with help of aluminum die cast connectors of 5 mm thickness Connector are fitted with A-pole with the help of M6x16 pan-head machine screw and washer. The corner & tops are concealed by post cover which are of different anodized aluminum profiles all 2way,3way and 4 ways junction is covered with Die cast aluminum caps Management :

The rectangular slots for wires on the upright is 60mm high by 23mm width ,1 no at the bottom and 6 nos at the intermediate level where in each slot can allow 9 power cable of dia 10 or 32 data cable of dia 6. The bottom horizontal would also have 2 slots for carrying wires, which are of size 60mmLx23mm(W) for wire carrying Raceways of 120mm high made up of anodized aluminum is provided at skirting and above/below the worktop. Keyboard pull out tray of made of 1.2 mm thick CRCA steel duly powder coated, of minimum thickness 50 micron, with metallic roller slides on both sides on Telescopic mechanism and shall be fixed to the bottom of worktop surface with the help of screws. The size of Keyboard tray is 240mm x 484mm and shall be suitable to accommodate keyboards of standard sizes and CPU Trolly of size 250x250x234mm (ht) made of 0.7mm thick CRCA steel sheet, duly powder coated of thikness not less 50 micron in colour of approved shade with 50mm dia castors to provide mobility. The width of CPU should ha adjustable complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 3000mm X 1800mm X 750mm conference table 72mm Thick Top with Provision of Power Dock mounting facility mounted on Box type gable end of 200mm thickness and Full height apron providing space for wire management within alongwith. Table top 72mm thick Top surface of conference table shall be the combination of different types of Top such as Stationary Main Top with provision for Power Dock fixing, Openable Top with provision of Power Dock placement and Stationary Side top. Side Top and Main Top shall be made up of 18mm PVC foiled MDF with three batten of same thickness fited arround the edges from Bottom side. PVC foiling of top after fitment of one batten to it and rest two battens are foiled together to give a look of two solid blocks of 36mm thickness joined together to form a muscular look of 72mm thickness. Side Top shall be of Vermont color and Main Top are finished in matt black color . Central Tops with openable fiture are made up of 18mm thick pvc foiled MDF act as horizontal box cover to access the wire mangement provision with piano hinges. Side Top of 600mm width and length as per final size in case of final size is more than 2400mm the table top shall be splitted in two equal part.,

Main Top of 600mm X 600mm size and Openable top of 596mm width and length according to sizes. Leg 200mm thick box patern hollow leg made up of 18mm thick pvc foiled MDF with C shape part made by foil and fold process packed with cover panle made up of 18mm thick Pre-laminated Particle board. Modesty :- Made up of Prelaminated 18mm MDF. Provision of support panel below top for easy wire management across the Conference table length. Provision of wooden stiffners of 100mm width and 18mm thickness made up of PPB fixed below table top inline with Modesty panel. Wire Management :- Provision for wire pasing throughout the structure without mixing data and power connections, the wires can be pull inside the tabel from floor and placed in the boxes build below openable shutter. The access point for data and power can mount on Main top as well as openable top complete in all respect as per satisfaction of Engineer-in-charge.

Providing Meeting Table having a size of 1050X1050X750 Top : 25mm Table Top made up of 25mm thick Both side PVC foiled MDF. The Edges machined to have chamfred edges gives look of waterfall Edge. The Top fixed on Metal structure with floating look due to angled cutting. Under-Structure:- Under-Structure of table combination of Two C type Leg and two cross member joined together with the help of special connecting brackets. The Vertical Member of Legs shall be made up of M.S. Square pipe of 50X50X1.6mm thickness and Horizontal member of M.S. Square Pipe 40X40X1.2mm thickness. The Cross members lip sections 40X40 made out of 1.6mm thick CRCA sheet. The Cross Members and Leg shall be Clamped together with the help of one way block made up of di-casted MAZAK alloy. Provision of Special Leveler Brackets and end clossing caps complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing Computer Table with Keyboard and drawer three layers prelaminated particle board of grade type-2 IS 12823/ Gable end and modesty panel material three layer prelaminated particle board of grade type-2 IS 12823/ 25 mm thick. Length of table 915 mm depth of table 610 mm height of table 840mm complete in all respect as per satisfaction of Engineer-in-charge.

Providng and fixing chair for workstation having a size of 45 cm (W) 42 cm (D) and back 39 cm (w) 47 cm (H) SEAT/ MIDBACK ASSEMBLY. The seat and back are made from 1.2 thick hot pressed plywood and upholstered with fabric and moulded polyurethane foam together with seat and back cover. The back foam shall be with contoured lumbar support. Seat/ back covers injection moulded in black Co-polymer polypropylene. The HR polyurethane foam is moulded with density 45 +/-2 kg m3. The one piece armrest shall be injection moulded from black nylon fitted to the seat with armrest connecting bracket made of 0.5+/-0.05 cm thk HR steel. The permanent contact mechanism designed with the 3600 Upright position. The pedestal injection moulded in black 30% glass-filled nylon and fitted with 5 nos twin wheel castors complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing chair for discussison havig a size of Seat Size 49 cm (W) 44 cm (D) and back 49 cm (w) 47 cm (H). Seat/ Mid Back Assembly: - The seat and back shall be made from 1.2 thk hot pressed plywood and upholstered with fabric and moulded polyurethane foam with PVC lipping all rounds. The HR polyurethane foam is moulded with density 45 +/-2 kg m3. The armrest top injection moulded from black polypropylene fitted to tubular armrest M.S E.R.W tube and black powder coated .The tubular armrest supports hold together the seat and back. The permanent contact mechanism designed with the 3600 Upright position. The pedestal injection moulded in black 30% glass-filled nylon and fitted with 5 nos twin wheel castors complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing chair for conference table with seat and back made from 1.2 thk hot pressed plywood and upholstered with fabric upholstery cover and moulded polyurethane foam. Foam designed with contoured lumbar support and the seat with has extra thick foam on front edge. Seat Size 47 cm (W) 48 cm (D) and back 47.5 cm (w) 58 cm (H). The one piece armrest of injection moulded black nylon. The pedestal shall be injection moulded in black 33% glass-filled nylon and fitted with 5 nos twin wheel castors complete in all respect as per satisfaction of Engineer-in-charge.

Providing of office table having a size of ( 1200mmx600mmx750mm) 30 mm thick made up of 18 mm thick pre-laminated particle board with 12 mm thick PVC foil wrapped decorative profile made up of MDF fixed along all the edges from bottom side with Modesty panel made up of 18 mm thick pre-laminated particle board providing stability to structure and allow sufficient leg privacy to user “D” headed decorative aluminum profile fixed on it alongwith table drawer unit with two book and one file drawer size 404(W)x450(D)x675(H)mm complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing of Printer table having a size of 900mmx600mmx750mm) 30 mm thick made up of 18 mm thick pre-laminated particle board with 12 mm thick thin PVC foil wrapped decorative profile made up of MDF fixed along all the edges from bottom side with Modesty panel made up of 18 mm thick pre-laminated particle board providing stability to structure and allow sufficient leg privacy to user “D” headed decorative aluminum profile fixed on it complete in all respect as per satisfaction of Engineer-in-charge.

Providing Table having a size of 2250x2100mm Top and Return 30 mm thick Curved edge table top made up of 18 mm thick PVC foiled MDF with batten of same thickness and finish fitted all over the edge with decorative “D” headed aluminum profile fixed between joint of top and batten panel to avoid by forced pill-off of pvc foil from edge side resulting in a rich looking 30 mm solid free flow structure for executive seating The return top of 30mm thickness with same structure as main top to be fixed on return unit with the help of table top support made up of M.S round pipe epoxy powder coated. Size alongwith Combo storage with three drawers and two shutter with good storage capacity usable as return storage for office storage alongwith Carcass Top, Side Panel, Verticals, Bottom, Skirting Panel, Shelf of Dark shade and Shutters of Lighter shade are made up of 18mm thick Pre-laminated Particle board with proper grooving done near to back side edge of side panel and Bottom for fitment of back panel made up of 9mm thick prelaminated particle board. There is provision for a pedestal structure (i.e. Two Book drawer and one file drawer) and two Open able storage places with adjustable shelf within.

Drawer :- Provision of two book Drawer of size 321(W) X 400(D) X 80(H) and one File Drawer of size 321(W) X 400(D) X 225(H) made up of 12mm thick Prelaminated Particle board with bottom panel of 9mm thickness. The small drawers are mounted on Telescopic slide with 3/4 extension. Where Big Drawer mounted on Telescopic slide with full extension allowing storage of files with the help of file manager. Drawer facia of Lighter shade made up of 18mm thick prelaminated particle board. Provision of centralize locking for all three drawers and D type slim Handle for Drawer and Shutter complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing of officer chair high back having a size of seat size 47 cm (W) 48 cm (D). Seat Assembly The cushioned seat is made of injection moulded plastic outer & inner Plastic inner is upholstered with leatherette and moulded high resilience polyurethane foam density 45+/- 2 kg/m2. The cushioned back is made of PU foam with insitu molded MS E.R.W Round tube it upholstered ith leatherette Back Size 47.7 cm (W) 76.4 cm (D) .Armerst top is moulded foam polyurethane (PU) and mounted on to a drop lift adjustable tipe tublar armrest sport . The permanent contact mechanism is designed with the 3600 Upright position. The pedestal is is high pressure dia cast polished aluminium and filled nylon and fitted with 5 nos twin wheel castors Marval complete in all respect as per satisfaction of Engineer-in-charge.

Providing of vistor chair with arm of seat and back shall be made up of 1.2 ±0.1cm. thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and shall be upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam shall be designed with contoured lumbar support for extra comfort. The dimensions of the back shall be 49.0 cm. (W) x 47.0 cm and of seat shall be 49.0 cm. (W) x 44.0 cm. (D). The HR Polyurethane foam shall be moulded with density= 45 ±2 kg/m3 and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The armrest tops shall be injection moulded from black Polypropylene. They shall be fitted to tubular armrest supports made of dia 2.54 ±0.03cm. x 0.16 ±0.0128cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 40-60 microns ). The tubular armrest supports should hold together the seat and back. The tubular frame shall be cantilever type & made of 0 2.54±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated (DFT 40-60 microns). Overall Dimensions of Chair shall be Seat Height - 43.0cm, Height - 80.0cm, Width & Depth of Chair as measured from pedestal - Width-55.0 cm and Depth-61.0 cm. etc complete in all respect as per satisfaction of Engineer-in-charge.

Providing & fixing in synthetic leather (W) 134x (D) 87x (H) 73 cm Sofa 2 seater with Poly Poplin thread shall be provided on frame of plastic bottom PVC LEG: Woodscrew provided on frame in addition to M-8 / T-Nut, Plastic, Leg bottom-Pvc. Bush. Material of leg :- Plastic Material Handling Data Sheet (MSDS) for Glue complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing of Centre Table having a size of 1100mm(W)600mm(D)500mm(H) 8mm thick tempered glass top and 6mm thick tempered bottom glass for storage color Silver powder coated understructure Glass glass attached to the under structure via UV disc Load bearing capacity 30Kg etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing of outside sitting steel / chrome bench having a size of 183cm (L) x 67cm (W) and 77.5cm back seat height / 40cm seat heigt with Cross Beam made up of powder coated rectangular M.S. ERW tube Leg and armrest chrome plated made of cold rolled steel with 0.12+/- 0.013 cm thickness. Perforated shell Seat back shell it is powder coated made from cold rolled M.S. sheet .The side bar is made of chrome plated solid the shell is assembled on the cross beam with help of M bolts etc. complete in all respect as per satisfaction of Engineer-in-charge.

Supplying, installation, testing and commissioning of split air conditioner (DC inverter type Hot and Cold) 2.0 Ton with all features i.e. four way swing, sleep mode, on/off timer, super power cooling, super heating performance, moisture removal, night glow button, feel mode, wireless remote control, auto power restart, Health Ionizer, low voltage startup, anti mild dew, R 410 A – DC Inverter compressor healthy titanium dioxide coating upto 67% power saving, 4 metre connecting copper pipe alongwith AC wire and drain pipe, Titan Gold filter, Photocatalyst Filter, NANO filter, Catechin filter, Aniti Bacteria etc. alongwith voltage stabilizer and stand complete in all respect as per satisfaction of Engineer-in-charge (Volta/IFB/Blue star/Godrej/Llyod make).

Supplying, installation, testing and commissioning of split air conditioner (DC inverter type Hot and Cold) 1.5 Ton with all features i.e. four way swing, sleep mode, on/off timer, super power cooling, super heating performance, moisture removal, night glow button, feel mode, wireless remote control, auto power restart, Health Ionizer, low voltage startup, anti mild dew, R 410 A – DC Inverter compressor healthy titanium dioxide coating upto 67% power saving, 4 metre connecting copper pipe alongwith AC wire and drain pipe, Titan Gold filter, Photocatalyst Filter, NANO filter, Catechin filter, Aniti Bacteria etc. alongwith voltage stabilizer and stand complete in all respect as per satisfaction of Engineer-in-charge (Volta/IFB/Blue star/Godrej/Llyod make).

Supplying and fixing ½ into ¼ inch copper pipe with AC wire complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 25mm dia PVC/plastic drain pipe for AC unit complete in all respect as per satisfaction of Engineer-in-charge.

Providing almirah of Overall size 1855 (H)x910(W)x480mm(D) Rigid Knock down construction with panels made from prime quality CRCA 0.8 mm thick and front frame made from CRCA 0.7 thick with three way locking bolting device controlled by 6 lever lock finish Epoxy powder coated complete in all respect as per satisfaction of Engineer-in-charge.

Lecture Podium with built-in subwoofer ,loudspeaker ,one tweeter with 60 w rated output ,Gooseneck microphone ,LED reading lamp ,with VHF- handheld wireless mic with range 15-20 m built in control panel ,1 AUX input independent control complete in all respect as per satisfaction of Engineer-in-charge.

Prem Chand