Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹77.2 LAccepted-AOC H NO 17036 9 STREET NO 5 A AGGARWAL COLONY BATHINDA PB 151001 | BATHINDA | BATHINDA | PUNJAB | 151001 | L1 | Accepted-AOC Being L-1 and reasonable rate | |
| 2 | L2₹77.3 L+₹15,249 (0.20%)Rejected-Finance H NO 18 SHEET NO 5 A KATIA COLONY NAMDEV MARG BATHINDA 151001 PB | BATHINDA | BATHINDA | PUNJAB | 151001 | L2 | Rejected-Finance Being not L1 | |
| 3 | L3₹77.5 L+₹36,535 (0.47%)Rejected-Finance 1000 PUDA MODEL TOWN PHASE 5 BATHINDA 151001 | BATHINDA | BATHINDA | PUNJAB | 151001 | L3 | Rejected-Finance Being not L1 | |
| 4 | L4₹78.8 L+₹1.6 L (2.13%)Rejected-Finance 18969 A 1 SHRI GURU TEG BAHADUR NAGAR BIBIWALA ROAD STREET NO 15 BATHINDA 151001 | BATHINDA | BATHINDA | PUNJAB | 151001 | L4 | Rejected-Finance Being not L1 |
Tender Value
₹80 L
EMD Value
₹1.4 L
Closing Date
12 Dec 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
CWE Bathinda
HQ CWE Bathinda, Bathinda Military Station
SPL REPAIR TO BLDG NO. P-208 (OR LIVING) AT BATHINDA MIL STN
2022_MES_550521_2
CWE BTD 8127/2022-23/E8
Open Tender
Civil Works
Item Rate
270 days
BATHINDA
As per NIT
6 documents required · 6 mandatory
₹1,000
GE (South) Bathinda
₹1.4 L
Yes
26 Dec 2022
22 Nov 2022
14 Dec 2022
22 Nov 2022
12 Dec 2022
29 Nov 2022
22 Nov 2022 - 28 Nov 2022
Amount
Preparation of Architectural working drgs including structural design drgs detail of Bldg " Reconstruction fo toilet blocks of buildings ( three story) of size 11.50m x 6.5m through any E-in-C's Br approved consultant. The vetting of structural design including all design calculation and drawings shall be done from IIT/NIT/ Govt. Engg. College.
Soil testing bore report through MES approved consultant complete all as specified and directed. Soil investigation is to be carried out as per IS-1892. Bore hole dia sahll be 150 mm and depth of bore shall be decided as per the soil condition and may be taken 15 m or N value reaches 50 whichever is earlier. Note:- Under this test following results also be provided:- (i) Grain size analysis, identification adn classification of soil. (ii) Unit weight ( bulk density) nature moisture content, liquid limit, plastic limit, shrinkage limit, plasticity index & specified gravity. (iii) Dry density degree of saturation of soil. (iv) Free swelling index and swelling pressure if expensive soil is encounter. (v) Shear parameter. (vi) Consolidation test and permeability test. (vii) Depth of water table below ground level. (viii) Presence of loose soil and if any and its depth. (ix) If weak soil with less N value as specification in table-1 of IS-1893-2016 is encountered then evaluation fo liquefaction porential shall be assessed and remedial action to be adopted shall be specified. (x) SPT test shall be done at 1 m interval. (xi) Recommendation fo regarding type fo foundation to be adopted and net SBC / pile capacity to be adopted also recommendation shall be given regarding stability of soil and soil stabilization required if any. (xii) Recommendation for fillign under floors and filling under plinth protection. (xiii) Bore hold position duly marked on plan and there distance from adjacent prominent reference point. (xiv) For open foundation, calculation of net SBC at 1.5 m, 2 m, 3.0 m from shear as well as settlement criteria. SBC values shall be calculated based on C-Øanalysis as well as SPT value. For calculation formula given in IS 6403 shall be used.
(xv) Plan size of bldgs shall also be marked in the plan. This plan shall be signed by GE,AGE & soil consultant & Contractor (xvi) Undisturbed soil sample shall be collected at 1.5 m interval and at change of strata. K-value of soil 0.5 m depth required in case of swimming pool and water retaining structure. Modulus of subgrade reaction , Direct shear test on un-disturbed soil sample(xvii) Submission of report in duplicate. Note: Colour photograph on A4 size paper of the site with the locations of the boreholes duly flagged should be submitted. The photographs should also preferably include any reference structre and the identification of the same be marked
Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each as in door, windows and ventilators etc including cutting holes for removal of hold fast complete all as specified.
S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm pre laminated PVC sheet reinforced with MS square tube, supplying and fixing in opening as specifications and drawing all as specified.
S&F factory made solid PVC moulded door shutters 28 mm to 30 mm thick with 2, 4, 6 raised panel designed with 2 mm thick moulded pre laminated PVC sheet on front face and 2 mm plain colour PVC sheet on back face including particle board core complete all as specified and directed.
S & F 100 mm long aluminium anodised butt hinges with galvanised mild steel screws complete.
S & F 150 mm long aluminium anodised, barrel tower bolts extruded section complete.
S & F 125 mm long cast type aluminium anodised handles complete.
Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 Sqm each as in doors, windows and ventilators etc including cutting holes for removal of hold fast complete.
S&F factory made pressed steel frames of size 125 mm x 60mm for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc (thickness of MS sheet shall not be less than 1.25 mm), including making good the wall with cement plaster in CM 1:6 compete, all as specified.
S&F factory made pressed steel frames of size 105 mm x 60mm for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc (thickness of MS sheet shall not be less than 1.25 mm), including making good the wall with cement plaster in CM 1:6 compete, all as specified.
M & L for PCC (1:3:6) type C-1 using 20 mm graded stone aggregate for filling in bed block of hold fast etc complete.
Taking down shutters of any description exceeding 1.00 Sqm and not exceeding 2.00 Sqm each and re-fixing the same in same opening complete all as specified.
S&F for 35mm thick factory made flush shutter solid core construction with block board core and plywood face panel commercial type on both sides complete all as specified and directed .
S & F factory made glazed and skeleton shutters 35mm thick using second class hard wood open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24(a); all as specified complete.
S & F mild steel wire cloth, 0.56 mm nominal dia of wire & average width of aperture 1.18mm and fixed with tinned tackes or galvanized wire staples complete.
S & F in repair 300 mm long MS ordinary rat tail rod pattern springs for doors including roller and roller plate complete.
S&F 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.
S & F mild stee barrel tower bolt 200 mm long stove enamelld black with bright bolt complete all as specified.
S & F mild steel pressed handle, oval type 150 mm long stove enamelld black complete all as specified.
S & F factor made steel window box type using ERW hollow 'P' section comprising double frame for and inclduing gauged skeleton shutter jointed internally with flat iron 40x4 complete including grill of 8mm sq bar fixed horizontally @ 100 mm C/C hinges handle tower bolts, stop lugs etc complete all as specified and directed as per TD drawing No. BTD-889.
S & F aluminium powder coated ventilator including provision of necessary rubber gas kit for fixing glass panes etc complete all as specified and directed and as shown in drawing No. CEBT/SK-936.
S & F figured glass pin head type sheet glass, 4 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane as in ventilators complete.
Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins / spring clips of size not exceeding 0.5 Sqm each pane and S & F 4 mm thick ordinary sheet glass and glazing with oil putty complete all as specified.
S & F for factory made flush shutter 25mm thick solid core construction with block board core and plywood face panels commercial type on both sides including teak wood beading complete.
M & L for painting to new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified.
M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified.
M & L rendering 15 mm thick C:M 1:3 mixing with WPC @ 200 ml per bag of cement on fair faces of concrete surfaces after wire brushing and cleaning surface and finished even and smooth without using extra cement complete all as specified. (WPC shall be measured and paid separately)
Supply only liquid water proofing compound complete all as specified.
M & L for applying two coats of Dr Fixit, pidecrete in sunken floor portion of toilet, bathroom, chajjah, stair case etc by using proportion of 1 kg/ 2 Sqm and applying by brush complete all as specified and as directed.
M & L for PCC (1:5:10) type E2 using 40 mm graded stone aggregate as in filling of sunken floor etc complete all as specified.
Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified.
M & L for non skid ceramic coloured tiles, 7 to 8 mm thick (square / rectangular) in floor area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over and including M & L for 15 mm thick screed bed of mortor (1:4) complete all as specified.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish to a distance exceeding 1 kilometer but not exceeding 2 kilometer complete all as specified.
M & L for glazed ceramic coloured tiles 450 x 300 mm, 7 to 8 mm thick in vertical surfaces such as in dado / skirting, set and jointed in neat cement slurry and pointed with white/ coloured cement to match the shade of tiles and over and including M & L for 10 mm thick rendering in cement mortar (1:4) as backing coat and finish the surface rough to receive the tile complete all as specified.
M&L for marble work (Udaipur green slabs) in one piece 15 to 16 mm thick slab of WHB cills of windows and urinal partition and like in laid over and including M&L for 15 mm thick cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade and roundening to the edge of stone slabs on edges etc. all as specified.
M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified.
M & L for machine cut kota stone slab flooring 18-20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.
All as per ser item No. 38 here-in-above but in vertical surfaces such as steps, riser, skirting , dado and pillars complete all as specified.
S & F 0.63 mm thick plain galvainsed, mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating complete all as specified.
S & F in repairs, CP basin mixture single lever type and fixed complete all as specified and directed. Make : CERA Cat Part No. F1017451/Hindware Cat Part No. F520011CP/ Jaquar Cat Part No. COPCHROO1BPM.
S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified
S&F in repairs stop valves, chromium plated angular type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union for 15 mm bore dia of pipe complete all as specified. Make : Hindware Cat Part No. F530043CP/ CERA Cat Part No. F1012201/ Jaquar Cat Part No. KUPCHR35053PM.
S & F in repairs brass chromium plated shower rose 125 mm size with or without swivel joints fixed to steel pipe or union complete all as specified and as directed. Make : Hindware Cat Part No. F160142CP/ CERA Cat Part No. F7010212AB/ Jaquar Cat Part No. OHSCHR1789.
S & F in repairs stop valves, cast copper alloy, fancy type, quarter turn, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe. Make : Hindware Cat Part No. F260018CP/ CERA Cat Part No. F1012351/ Jaquar Cat Part No. ADLCHRO69FT (Reduce Body) & CQTCHR23069K (Exposed Part).
S&F in repair brass chromium plated tubular towel rail, 20 mm dia, D type, 600 mm long between flanges fixed with CP screws and wooden cleats complete all as specified and as directed.
S & F in repairs, stainless steel chromium plated soap tray of size 100 x 100 x 6mm and fixed on wall with chromium plated brass screws complete.
S&F in repairs 15 mm bore chromium plated fancy type quarter turn, bib taps, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule complete all as specified . Make : Hindware Cat Part No. F440003CP/ CERA Cat Part No. F1012151/ Jaquar Cat Part No. CQTCHR23047.
S & F in repair grating doom 125mm dia with waste hole of PTMT (minimum weight 40 gm).
S&F in repairs drapery rod (conduit) of dia not less than 25mm duly powder coated of shade as decided by Engr-in-Charge including ABS plastic finials of approved shade and including standard MS powder coated brackets fixed to walls with rawl plugs and steel screws complete.
Taking up or down 15mm bore galvanized iron tubing and connections complete all as specified.
Taking up or down 20mm bore galvanized iron tubing and connections complete all as specified.
S & F GI tubing medium grade ISI marked with all fittings and fixed to walls & ceiling or laid in floors, bore of pipe 15 mm complete all as specified
S & F GI tubing medium grade ISI marked with all fittings and fixed to walls & ceiling or laid in floors, bore of pipe 20 mm complete all as specified
Taking down rain water pipe any size including all fittings such as head shoes, bends, swen neck etc complete all as specified and directed.
S & F PVC (SWR) 110mm bore pipes, single socketed, in any length with rubber ring joints fixed to wall with mild steel climps of suitable size complete all as specified.
S & F 110 mm bore PVC (SWR) bends ISI marked of any radius / shoe, fixed to PVC pipes complete all as directed.
S & F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. including making good to floor and excluding flushing cistern, flush pipe and waste pipe complete.
S&F in repairs PVC low level valveless syphonic action type flushing cistern of capacity 10 ltr , white with inlet, ball valve, float and handle including brackets and flush PVC pipe of high density of 32 mm dia,900 mm long including S & F long P trap complete all as specified
S & F in repairs vitreous china, counter sunk oval shaped wash hand basin, white, of size 560mm x 450mm , including 32 mm dia brass chromium plated waste coupling and PVC waste pipe including angle iron brackets complete all as directed complete, .
S & F in repair vitreous china urinal, half stall type, white (excluding flushing cistern , flush pipe & waste pipe) including connections to flushing pipe and out going pipes complete all as specified.
Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section ) in cement concrete (1:2:4) type B-1 smooth finished, and reforming benching as required for 150mm dia pipe complete all as specified and as directed.
Dismantling and disconnecting of existing cast iron soil waste & vent pipe 100 mm bore fixed to wall or laid in trenches or in floors including all fitting and accessories complete all as specified.
Dismantling and disconnecting of existing cast iron soil waste & vent pipe 75 mm bore fixed to wall or laid in trenches or in floors including all fitting and accessories complete all as specified.
S & F 100 mm dia cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, fixed to walls with and including suitable size clamps complete all as specified.
S & F 75 mm dia cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, fixed to walls with and including suitable size clamps complete all as specified.
S & F in repair 100 mm dia cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified.
S & F in repair 75 mm dia cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified.
S & F in repair 75 mm dia CI floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1, complete all as specified.
S&F in repair 100 mm dia cast iron branch pieces, single (equal or un-equal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete.
S & F in repair 75 mm dia cast iron branch pieces, single (equal or un-equal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete.
S & F in repair 100mm cast iron Cowl fixed with cement joint in cement mortar 1:2 complete all as specified.
S & F in repair 75mm cast iron Cowl fixed with cement joint in cement mortar 1:2 complete all as specified.
M & L in repair for 100 mm dia CI floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1, complete all as specified.
M & L for extra for joints over cast iron pipe of 100/75 mm bore pipes, bend joints etc provided Epoxy joints in lieu of cement joints complete.
S & F SFRC (Steel fibre Reinforcement concrete cover & frame) heavy duty HD-20, grade designation conforming to IS-12592, graded rectangular clear opening 800 x 800mm total weight of cover and frame not less than 182 Kg fixed in cement concrete (1:2:4) etc complete all as specified.
Taking down old cement plaster including raking out joints hacking for key scrubbing down with water etc and removing rubbish from the premises to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.
M & L for rendering 15 mm thick on internal surface in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finishing the surfaces even and smooth without using extra cement complete all as specified.
M & L for rendering 15 mm thick on external surface in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finishing the surfaces even and smooth without using extra cement mixed with liquid water proofing material as per manufacturer's instruction complete all as specified. Note:- Liquid water proofing material shall be measured and paid for separately.
M & L for rendering 5 mm thick on ceiling in cement mortar (1:3) finishing the surfaces even and smooth without using extra cement complete all as specified.
Demolition of brick work masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and pre cast concrete articles as in foul condition complete all as specified..
M&L for 75 mm thick PCC (1:3:6) type C-2 using 20mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement complete all as specified.
Dismantling of old water tank of exceeding 500 ltr and not exceeding 1000 ltr complete all as directed
S & F 1000 ltr capacity Rotational moulded polyethylene in white colour, three layered, ISI marked, water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified.
S&F in repair ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 25 mm bore (minimum weight 20mm-210 gram) complete all as specified.
S & F in repair for 20 mm bore Gun metal globe or Gate valve with iron wheel head, ISI marked, screwed both ends for iron pipe or for unions complete.
Complete removal of existing treatment of internal wall (any number of layers) by scrapping with steel wire brushes or any other means, including filling depressions of scrapped surfaces with 3 mm thick wall putty and preparation of surfaces for further treatment etc complete all as specified
M & L for applying two coats of oil bound distemper over a prepared of old surfaces of wall complete all as specified.
M & L for applying two coats of white wash including preparing surfaces of od wall complete all as specified.
M & L preparation of newly plastered or unplastered surface and applying three coats of white wash on walls complete all as specified.
M & L for complete removal of existing surfaces of ceiling and applying three coats of white wash etc complete all as specified.
M & L preparation of newly plastered or unplastered surface and applying three coats of white wash on ceiling complete all as specified.
Complete removal of existing treatment and preparation of surfaces of walls and applying two coats of acrylic emulsion paint @ 1.43 Ltrs per X Sqm over a priming coat of exterior primer complete all as specified. Note:- The work shall be got executed from authorised applicator of maufacturer and approval will be given by GE. 5 year unconditional guranteee will be given by contractor through manufacturer as described in PS clause of tender documents.
M & L for preparation of newly plastered surfaces of walls and applying two coats of acrylic emulsion distemper over a coat of 3mm thick putty of approved tint complete all as specified.
M & L for preparation of old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint on wooden surfaces complete all as specified.
M & L for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint on steel surfaces complete all as specified.
Demolition of brick tiles or terracing tiles, single layer on roofs including removing the demolished material exceeding 1 km and not exceeding 2 km away from site and disposal off in low lying area as directed.
Demolition of mud in roof, any thickness including plastering and leaping (where full thickness recovered or only a part there of) including removing the demolished material not exceeding 200 m away from site and disposal off in low lying area complete.
M&L for wire brushing and cleaning top surfaces of roof slabs etc, including washing the roof surface with water and making the surface free from mud and previous treatment, making surface good to receive further treatment etc complete all as specified.
M&L for 15 mm thick screed bed or bedding layer in cement mortar (1:3) on roof surfaces parapet or vertical beam surface (horizontal or vertical) finishing the surfaces even and fair complete all as specified. (Note :- Course sand (Toka sand) shall only be used in screed bed/plastering.)
M&L for water proofing treatment over RCC slab by applying oil bound bituminous primer @ 0.30 kg/Sqm and providing and laying 3mm thick APP modified water proofing memberane weighing not less than 3.50 kg/sqm, reinforced with non woven polyester reinforcement matt weighing not less than 160 gm/Sqm polyester core, having soften point not less than 150°C, longitudinal tensile strength not less than 650 N/ 5 cm, tearing strength of 180 N, torch application, side overlap 75 mm and end overlap 100 mm and tucked into the chases including ponding test all as specified and directed.
M&L for Lime concrete in lime mortar (1:3) using 40 mm graded brick aggregate, laid to slope as directed by Engineer in charge over RCC roofs as padding complete all as specified. Note: Minimum thickness of lime concrete at lower end shall not be less than 50mm.
M & L for 20- 22 mm thick factory made PCC tiles of size 250mm x 250mm with grey cement and no pigment , bedded in cement mortar (1:4), 15 mm thick and joints grouted flush in CM (1:3) mixed with @ 5% of crude oil by weight of cement over lime concrete roof padding surface complete all as specified.
M & L for PCC (1:2:4) type B1 using 20mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified.
Demolition of RCC as in roof floors (other than ground floors), beams, stair case, landing, chajjas, and similar suspended work and in any position not otherwise specifically provided for including reinforcement cut as required to facilitate demolition complete all as specified.
Excavation in trenches, not exceeding 1.5 metres in depth and 1.5 mtr width for foundations etc and getting out in soft/loose soil.
Excavation in trenches, not exceeding 1.5 metres in depth and 3 mtr width for foundations etc and getting out in soft/loose soil.
Removing excavated soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5mtr the starting point complete all as specified.
Returning, filling in, including spreading, levelling, watering and well ramming of soft/ loose soil in layers not exceeding 25cm thick.
M & L for PCC (1:4:8) type D2 using 40mm graded stone aggregate in foundations, filling and mass concrete etc complete all as specified.
M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6) complete all as specified.
M&L for half brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6) complete all as specified.
M & L for RCC M-25 (Design Mix) using 20 mm graded stone aggregate in foundation , footings , including rafts , foundation beams , plinth beams , bases for columns and basement slab etc all as specified and directed. (Note - Reinforcement and form work shall be measured and paid separately)
All as per ser item No. 115 here-in-above but for columns, pillars, piers, post and struts .
All as per ser item No. 115 here-in-above but for beams, cantilevers, bressummers, lintels .
All as per ser item No. 115 here-in-above but for chajja .
All as per ser item No. 115 here-in-above but for slab supported on walls .
M & L use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) for flat rough finished surfaces of concrete complete all as specified.
M & L for use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exc 20cm wide and sides of RCC /PCC bands in walls, horizontal or sloping and similar work exc 5cm but not exc 10cm wide with rough finished surface of concrete.
M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions having square, rectangular or polygonal shape with rough finished surface of concrete.
M & L for use and waste of form work to concrete foundation , footings , bases of columns, rafts and beams , sides and soffits (if any) of foundation and plinth beams and similar works , vertical or to battle for rough finished surfaces of concrete flat all as specified.
M & L for use and waste of formwork to sides and soffits of roof beams, gable beams, lintels etc with rough finished surface of concrete complete all as specified.
M & L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges with fair finished surface of concrete complete all as specified.
M & L for TMT bars 10mm dia and over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified.
All as per item No 126 above but TMT bars 5mm dia and over upto including 10mm did ,as in stirrups , spacers & binders all as specified.
M & L for treating the bottom and sides of excavation/ top of filled earth/ plinth protection area at the @ 5 litre of emulsion per square metre of surface area complete all as specified.
M & L for treating the back fill in contact with foundation @ 7.5 litres of emulsion per square metre of vertical surface complete all as specified. Note:- Area of the substructure in contact with backfill to be measured.
M & L for 75 mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base, floor, path, pavings etc complete all as specified.
M & L for 30mm thick PCC (1:2:4) type B-2 using 12.5mm graded stone aggregate as in floor etc complete all as specified.
M & L Hard core of gauge not exceeding 63mm , using broken stone or boulder , deposited , spread & leveled in layer not exceeding 15 mm thick watered and rammed to a true surface complete.
Carefully chipping, removing existing loose/ damaged concrete with plaster from Roof, Ceiling, Chajja, Fascia, Fins, Drops and similar items by low impact high frequency hammer/ chipper without damaging the existing sound concrete and exposing old reinforcement upto 10mm beyond corroded reinforcement bars using electrically operated diamond concrete saw blade, making the edges straight and even and cleaning it by wire brush and then by air blower complete all as specified and as directed by Eng-in-Charge.
Cleaning all existing reinforcement bars in Roof, ceiling, Chajja, Fascia, Fins, Drops and similar items with wire brush/ rotary wire brush to make entire circumference surface of bars free from rust scales, loose material, dirt etc, complete and applying alkline rust converting primer on the existing rebar and allowing it to react with rust for 6 hrs and form a coorsion resistant, insoluble and adherent protective layer including cleaning the reinforcement, wire brushing to remove the rust spalls, complete as per manufacturer's instructions, complete all as specified and directed by Eng-in-Charge. Note:- Mode of measurement per sqm of breaking area of concrete only. Make :- Sika Rust off-100/ Fosroc- Reebaklens RR/ Pidilite Dr Fixit Rust Remover or equivalent make approved by E-in-C's Branch.
Providing and application of zinc rich epoxy anti-corrosive protective coating on reinforcement bars as corrosion protection system in 2 coats to the entire circumference surface of bars ( consumption Qty as per manufacturer's instructions but min 0.4 kg/ Sqm approx) in roof, ceiling, chajja, Fascia, Fins, Drops, columns, Beams and similar items complete all as specified and directed by Eng-in-Charge. The product should confirm carbonation resistance of 2mm and bond strength > 1N/Sqmm according to ASTM C-882-78 complete all as specified. Make :- Sika- Friazinc R/ Fosroc- Nitozinc Primer/ Pidilite Dr Fixit zinc rich primer or equivalent make approved by E-in-C's Branch.
Apply SBR based bonding agent to the opened grooves in the concrete before filling up with Polymer modified mortar or any other treatment ( consumption Qty as per manufacturer's instructions but min 0.4 kg/ Sqm approx) including cleaning the surface to remove dirt, dust or any other impurities on the surface in roof, ceiling, chajja, Fascia, Fins, Drops, columns, Beams and similar items complete all as specified and directed by Eng-in-Charge. Make :- Sika- Sika Dur 32 LP/ Fosroc- Nitobond SBR (EP)/ Pidilite Dr Fixit Super Latex (EP) or equivalent make approved by E-in-C's Branch.
Rebuilding the section of structural damaged RCC/PCC elements of Roof, ceiling, chajja, Fascia, Fins, Drops repair to spalling concrete to its original size and shape in layers of 10 mm average thickness in 1st layer by providing and applying with pre-batched, one component fiber based repair mortar having compressive strength>= 50 N/Sqmm (28 days) according to ASTM C 109, flexural strength >= 5N/Sqmm (7 days) according to ASTM C-293-79 complete all as specified and directed by Eng-in-Charge. Make :- Sika- Monotop 122 F/R Fostroc- Renderoc S2/ Pidilite Dr Fixit Polymer Mortar HB or equivalent make approved by E-in-C's Branch.
Rebuilding the section of damaged RCC elements to its original size in thickness upto 100 mm by supply and casting with ready to use non shrink. Cementations free flow micro-concrete having compressive strength > 60 N / mm (28 days) according to ASTM C 1107-99 including mixing, placing and leveling the surface by grinding off cementations slurry or cementations joints differences if any and cruing complete all as specified. Note:- Mode of measurement per Kg of micro concrete only. Make :- Sika -Sika rep Microcrete 4/Fosroc- Renderoc RG/ Pidilite Dr Fixit Micro concrete or equivalent make approved by E-in-C's Branch.
Supply and Grouting injecting two part, low viscosity, moisture insensitive injection liquid, based on high strength epoxy resin by pressure and using pressure epoxy injector with accessories till nozzle refused to accept the grout including mixing of grout having following properties (i) Mixed Density 1.1 kg/1 (at + 27ºC) : Viscosity -250 m Pass at + 30ºC and should comply according to ASTM C 881 Type II and IV , Grade-I , class E+F (ii) Compressive strength >= 70 N/mm2 (7 days) according to ASTM C 579 : Tensile strength -50N / mm after 7 days at +30ºC cure) (According to ASTM D 638). Tensile modul- 2000N / mm( after 7 days at +30ºC cure) (According to ASTM D 638),(iii) Bond strength -10.8N / mm (failure in concrete ) after 14 days at +30ºC cure) Flexural strength -50 N / MM according to ISO 178. (iv) Seal with nozzle with thixotropic epoxy adhesive after the refusal of grout material from the nozzle. Note :- (i) Leakage through other nozzle or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost complete all as specified and as directed by Eng-in-Charge.(ii) Mode of measurement per kg of materila consumed. Make :- Sika-SikaDur 52 LP/Fosroc- Conbextra EP 10 / Pidilite Dr Fixit Epoly Injection Grout or equivalent make approved by E-in-C's Branch .
Drilling holes of 12mm dia upto 100 mm deep holes in structural members at the interval of 300mm in staggered manner or along the crack line in reinforced concrete (RC) structural element including cleaning of the holes by air blower and inserting 12mm dia NRV (Non Returnable Valve) nozzle compatible with epoxy injector and having machined external end to receive outlet of Grouting Gun. Fix inside the hole by applying thixotropic epoxy adhesive to ensure complete sealing and allow curing the system for minimum of 8 hrs before Grouting including nozzle projections, excess putty, if any, over concrete element by gridding , leveling and finishing the external surface after completion of the work etc complete all specified and as directed by Eng-in-Charge. Make epoxy adhesive Sika/ Fosroc/ Pidilite Dr Fixit) or equivalent make approved by E-in-C's Branch.
Note:- Item No. 133 to 140 shall be executed by authorised applicator of Manufacturer and approval will be given by GE.
S & F MS framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc, not exceeding 10 Kg each brackets, conforming to Fe 290 Gde E-165.(Brackets over 10 kg each to be measured under ' Structural Steel) cooler stand etc complete.
M & L pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour, having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified.
Taking down 32 mm bore pipe and connections complete all as specified and directed.
S & F GI tubing medium grade ISI marked with all fittings and fixed to walls and ceiling or laid in floors bore of pipe 32 mm complete all as specified and directed.
Forming jams etc to opening ( to forgoing items) including cutting, toothing and properly bonding into old work also facing, jointing and pointing to match existing work complete in CM 1:4 all as specified.
Cutting chases pinning in making good to facings where required and pointing in cement mortar 1:3 to ends and edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chases for concealed water tubing and concealed conduit wiring etc. and making good cutting not exceeding 10 CM girth as in brick walls complete all as specified and directed.
M & L for preparation of old/ new surfaces of walls by applying two coats of acrylic emulsion paint @ 1.43 Ltr per ten Sqm over a priming coat of exterior primer on column, beam, chajja, facia complete all as specified and directed.
S & F white vitreous china wash down water closet pan ( pedestal pattern) with and including water closet sheet white back, closed pattern with flat bottom and mild steel chromium plated or aluminium hinging device including flush pipe and fixing bolts ( excluding flushing cistern and including jet spray) etc compete all as specified and directed.
S & F stainless steel fancy type peg set of six and fixed in position with steel screws complete all as specified and directed.
S & F CP health faucet 15 mm bore including 1 Mtr flexible led complete all as specified and directed. Make : CERA Cat Part No. F8030107AB/Hindware Cat Part No. F160122CP/ Jaquar Cat Part No. ALD-CHR-565.
S & F 20 mm thick granite slabs for wash hand basin over 15 mm thick screed bed in CM 1:6 including moulding and nosing of corners/ edges complete all as specified and directed,
Taking down existing wooden cabinet and S & F built in locker of 1mm thick black steel sheet of size 760mmx 600mm x 1100 mm and specifications as per drawings No. FD-1029 including a coat of primer and two coats of synthetic enamel paint and provision of CP handle and mortice lock as per Godrej Pattern complete all as specified and directed.
S & F 4 mm dia GI wire fixed to walls with 16mm dia MS hasps & bolts for mosquito proofing complete all as specified.
Taking down carefully existing unserviceable copper / aluminum point wiring (light, fan, socket) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, light fittings etc except concealed conduit and sunken boxes and removing the retrieved materials from site including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.
M & L for point wiring for one light / fan point controlled by one switch with 1.5 sqmm (nominal area) PVC insulated unsheathed multi stand copper conductor cable FRLSH in and including concealed PVC conduit 20 mm dia heavy duty ISI marked, steel terminal sunken boxes and 3 mm thick phenolic laminated sheet top cover for sunken boxes flush to surface for one light point/ fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 sqmm copper conductor cable FRLSH connected to common earth dolly complete including cutting, chasing the surface and then making good the same in CM (1:3) complete all as specified and directed by Eng-in-Charge. Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of Sch 'A')
All as per item No 156 here in before but for one socket outlet 3 pin, 5/6 Amp 250 volts flush type on same board complete all as specified.
All as per item No 156 here in before but for one socket outlet 3 pin, 5/6 Amp 250 volts flush type on independent board complete all as specified.
All as per item No 156 here in before but for one socket outlet 6 pin, 6/16 Amp 2 in 1 with cable 2.5 sqmm multistranded copper conductor FRLSH cable on the independent board including provn of 2.5 Sqmm PVC insulated copper conductor FRLSH cable continues as earth wire connected to earth dolly complete all as specified.
All as per item No 156 above but for one light point controlled by two switches two way.
S &F switch piano flush type 5/6 Amp, ISI marked 230V AC, single pole, one way complete as specified.
S &F switch piano flush type 5/6 Amp, ISI marked 230V AC, single pole, two way complete as specified.
S &F Socket piano flush type 3 Pin ,5 Amp 230V AC complete as specified. ( Switch and socket shall be the same make)
S &F one switch and one Socket 2 in 1, 3 Pin ,15 Amp 230V AC complete as specified. ( Switch and socket shall be the same make)
S&F fan regulator electronic step type (1-5), socket type 230-240 Volt, AC supply suitable for 1200/1400 mm ceiling fan complete all as specified and directed.
S & F ceiling rose, surface bakelite type, 65 x 50 mm, three terminal with back plate etc complete all as specified.
S & F lamp holder PVC/Polycarbonate type surface including S & F 9/10 watt LED bulb complete all as specified.
S & F sheet metal enclosures double door made out of CRCA mild steel sheet, concealed, surface mounting, acrylic door, IP-43 protection, 8 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old unserviceable DB complete all as specified.
S & F sheet metal enclosures double door made out of CRCA mild steel sheet, flush mounted, acrylic door, IP-43 protection, 4 way, TPN 240 Volts AC with 200 Amps rated bus bar dust and vermin proof suitable for incorporation of MCBs and isolators etc including taking down old unserviceable DB complete all as specified.
S & F MCB SPN 40 Amps curves MCB repturing capacity 10 KA etc complete all as specified and directed by Eng-in-Charge.
S & F MCB SP 6 Amps to 32 Amp capacities ,C, series, rupturing capacity 10 KA etc complete all as specified and directed by Eng-in-Charge.
S & F sub main wiring with 2 single core cable PVC insulated unsheathed of copper multi standard conductor FRLSH cable of size 6 sqmm, 1100 volts grade drawing through in and including PVC concealed conduit 20 mm dia medium duty including accessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 6 sqmm unsheathed multistranded FRLSH copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishing the surface to match with existing surface etc including taking down old unserviceable wiring 6 Sqmm complete all as specified. Note:- Two runs of cable, one run of earth wire and one run of PVC conduit shall be measured as one unit.
M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia light grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note :- (a) PCC chamber shall be constructed at least 1.5 m away from earth pit. Pipe for watering shall be provided in slanting manner. (b) 4mm dia GI wire and 15mm dia light grade GI protection pipe upto 7.5 metre shall deemed to be included in quoted rate.
S & F blanking plate etc complete all as specified and directed by Eng-in-Charge.
S & F LED light fitting 1x20 watt, 230 volt, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified.
S&F 35 watt light fitting, 650 K , efficacy not less than 100 lumen/ watt, pressure die cast aluminium housing with toughened glass cover with IP-66 protection complete inbuilt driver & accessories including fixing with GI/MS bracket made out of suitable size of light grade tube upto 1.2 mtr length cut to length, bend to shape with 02 Sets of MS clamps made out of minimum 3 mm MS flat iron with suitable bolt and nuts complete with making connection complete all as specified.
S & F mini mirror LED light mirror type with high output diffuser 2 feet 10 watt 220 Volt AC decorative type with dirver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified.
S & F heavy duty metal body exahust fan of 300 mm sweep 240 volt, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up inlcuing 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2 mm from ceiling rose to fan complete all as specified.
M & L for making hole into any type of wall for fixing of exhaust fan including cutting of wall, grouting, plastering and making good with existing surface complete all as specified.
Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender from total amount of Schedule 'A'/BOQ
V K CONTRACTOR
M/s Kamal Builders
SHARDA ENTERPRIES
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .