Interior Modification of IMFL shop at Delanipur, Sri Vijaya Puram

Amount

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Providing and laying vitrified floor tiles in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Extra for providing and fixing wind ties of 40x 6 mm flat iron section.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour

Old work (one or more coats)

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

One or more coats on old work

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (including equivalent design mix)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade

Two or more coats on new work

Providing and fixing aluminium composite panel(ACP) 4mm thick (0.50+3.00+50mm) on anodized aluminium frame work using JINDAL/INDAL or equivalent box section of size 50x50x2mm thick and 40x40x3mm anodized aluminium angle at not more than 0.60 mtrs centre to centre spacing as per actual requirement at curves, junctions jointed with all necessary fixtures such as cleat angles,brackets, screws etc. fixed to wall for partition with necessary high performance imported double side CHB tapes, structural seatant (DOWCORNING NO.789,998) fixed so as to transfer the weight of Alcon panels (ACP) to aluminium frame work and to avoid undue stress on silicon sealant, closing the grooves (12-16mm) with weather grade silicon dealant ensuring the whole system water proof, rigid against wind using conversion resisitant hardware necessary paints thermal expansion/contration mechanism etc. complete as directed by Engineer-in-charge.

Aluminium panelling with anodized frame

Providing and fixing false ceiling at all height with aluminium composite panel(ACP) 6mm thick (0.50+5.00+50mm) on anodized aluminium frame work using JINDAL/INDAL or equivalent box section of size 50x50x2mm thick and 40x40x3mm anodized aluminium angle at not more than 0.60 mtrs centre to centre spacing as per actual requirement at curves, junctions jointed with all necessary fixtures such as cleat angles,brackets, screws etc. fixed to ceiling with necessary high performance imported double side CHB tapes, structural seatant (DOWCORNING NO.789,998) fixed so as to transfer the weight of Alcon panels (ACP) to aluminium frame work and to avoid undue stress on silicon sealant, closing the grooves (12-16mm) with weather grade silicon dealant ensuring the whole system water proof, rigid against wind using conversion resisitant hardware necessary paints thermal expansion/contration mechanism etc. complete as directed by Engineer-in-charge.

Aluminium panelling with anodized frame

Providing and fixing height adjustable floor standing metal shelves (heavy duty) end cap rack of approved quality of height 2.10 m and depth 0.45m having 5 shelves and the height between two shelves is 0.35m, all as per approved drawings and as per the direction of Engineer-in-charge.

Providing and fixing Billing Counter 'T" shaped model with 19mm laminated finish HDF board/19 mm thick marine ply with laminate including flap door, side door, draws with telescopic channel, shutters, locking arrangement, handles, hinges, all required fittings, materials etc. complete as per approved drawings and as per the direction of Engineer-in-charge.

Providing and fixing vinyl on grey laminte finish and stickering as per approved drawings and as per the direction of Engineer-in-charge.

Providing and fixing Name Board of frame size 3.0x0.60m in Backlit Acrylic sheet with "Logo & ANIIDCO LIQUOR STORE" etc. all complete as per approved drawing and as per the direction of Engineer-in-charge.

Providing and fixing of 19mm thick marine ply with laminate finish or HDF board laminate finish on dry wall as per approved drawings & as per direction of Engineer-in-charge.

Dismantling of existing display rack, counter table, grill, hand rail etc. including stacking of serviceable materials and disposal of unserviceable materials at dumping area etc. complete as per direction of Enfineer-in-charge.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

3 Module (100mmX75mm)

6 Module (200mmX75mm)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Providing and fixing LED tube light - 20W of make Philips, Luker or equivalent to ISI standard.

Providing and fixing LED 9W indoor ceiling spot light/focus light specially designed for commercial usage long life Make: Crompton or equivalent in Bajaj/Havells/Philips etc.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

1 x 2.5 sq. mm

Providing and fixing wall hanging LED smart TV of size 43" with suitable accessories for hanging the TV of approved brand like LG or equivalent to Samsung/Panasonic etc as per direction of Engineer-in-charge

K K Construction (BID ID -61563)

SONA MONA TRADERS (BID ID -61485)