SPL REPAIR TO BLDG NO P-107 AND P-150 AT DRUGMULLA IN THE AOR OF AGE B/R-III UNDER GE 874 EWS.

Amount

Demolition of Concrete cement concrete un reinforced in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of floor hearth or wall tilling including cement mortar bedding removing tiles to rubbish of the premises complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 20 mm graded crushed stone aggregate) as in plinth protection finished even and fair without using extra cement complete all as specified and directed.

M&L for 50 mm thick PCC 1:2:4, type B-0 using 12.50 mm graded aggregate for floor complete all as specified and directed.

M & L for plain cement concrete B-1, 1:2:4, type B-1, using type 20 mm graded aggregate , 25 mm thick as in sub base over rammed earth complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8 mm thick area of each tiles exc 0.18 sqm but not exc 0.38 sqm, laid in floors etc., set and jointed in neat cement slurry and pointed in white cement to match the shade of tile laid over and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement complete all as specified and directed.

M & L for Non-skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over 15mm thick rendering in Cement Mortar 1:6 complete all as specified & directed.

M & L for Glazed ceramic coloured tiles (450 x 300 x7mm) thick, as in vertical surface such as in skiting and dado etc, set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over 10mm thick rendering in Cement Mortar 1:4 complete all as specified & directed.

Dismantling plain or corrugated steel sheeting, any gauge thickness including Nainital or similar pattern roof covering complete all as specified and directed.

S & F Pre- painted galvanlume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering Ridge Factory Made Provide sheet fixed with self tapping screws complete all as specified and directed.

Dismantling wall and ceiling boards or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed.

M & L for second class soft wood in scantling clean swan complete all as specified and directed.

M&L plywood grade BWR type BB, 12 mm thick fixed with nails to timber frame work in ceiling complete all as specified and directed.

M&L for providing and Fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed.

M & L for plain fillets 2nd class soft wood of exc. 3 & n exc. 6 Sqcm, square rectangular or triangular in section, clean swan, secured with nails complete all as specified and directed.

M&L for preparation of newly un treated surfaces and applying two coat of synthetic enamel paint on wooden surfaces of any description not other wise described over 10 cm width or grith etc complete all as specified and directed..

Taking down chowkat with shutters exc.1.5 Sqm but n exc.4 Sqm (w/o taking off shutters from chowkhat) complete all as specified and directed.

Taking down chowkat with shutters n. exc.1.5Sqm (w/o taking off shutters from chowkhat) complete all as specified and directed.

S & F 2nd class soft wood plain solid straight chowkats and frames wrought framed, rebated on the solid complete all as specified and directed.

M&L for plain, framed, panelled shutters second class soft wood 35 mm thick (any number of panels), with panels of timber flat on both sides(feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

S & F Glazed and skeleton shutters, second class soft wood 30 mm thick open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

M&L for preparation of old painted surfaces and applying one coat of synthetic enamel paint on wooden surfaces of any description not other wise described over 10 cm width or grith etc complete all as specified and directed..

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffener and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing complete all as specified and directed. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

S&F 100 mm size mild steel butt hinges medium weight complete all as specified and directed.

S&F 75 mm size mild steel butt hinges medium weight complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 100 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F aluminium anodised alloy handles fabricated type 150mm size of handle complete all as specified and directed.

S&F 100 mm long aluminium handles cast type anodised complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised sliding door bolt, with hasp and staple (bolt type) cast or extruded section and fixing bolts of extruded section complete all as specified and directed.

Hacking out old broken glass (any thickness, size quality of description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F 03 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified.

S & F in Stainless Steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

S & F for Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. including of fixing supply pipe to flushing cistern, trap and waste pipe

M & L for Vitreous China wash basin, fancy bowl flat back size 550 x 400 m including waste pipe and coupling 32mm for basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed including MS brackets & waste pipe complete all as specified and directed.

M & L Mild steel bars 10mm TMT bars dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for precast cement concrete 1:2:4 type B 1 using ( 20 mm Graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed.

S&F 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platrom and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding off edges including cutting hole for wash basin fixing as per required size completed as specified and directed.

S& F in Vitreous China premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white closed pattern including all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified.

S&F in repair vitreous China squatting pan 'Orissa' pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing system anti syphonage pipe etc complete all as specified and as directed.

S&F in PVC valveless, syphonic action type, low level PVC flushing cistern 10 ltr capacity white with flush pipe & all fitting complete all as specified and directed.

S & F in repair Health faucet (ABS Body) mild steel Cr plated suitable for 15 mm dia pipe with 1.25 m long tube complete all as specified and directed.

S&F Bib taps cast copper alloy, chromium plated, with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

S&F in repair pillar tap cast copper alloy, fancy type with capstan heads chromium plated screwed down with high pressure with or without lettered hot or cold with long screwed, shanks and fly nuts screwed for iron pipe 15mm dia complete all as specified and as directed.

S&F 20 mm Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed

S&F ball brass valve, with polyethylene float and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and directed.

S & F 15mm bore Stop/Angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs two way angular stop cock chromium plated 15mm dia complete all as specified and as directed.

S&F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F PVC connection 15mm dia and 600mm long with PTMT nuts and washer complete all as specified and directed.

S&F PVC connection 15 mm dia bore and length 450 mm fixed complete all as specified and directed.

Taking up or down 15mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

S&F GI tube 15 mm dia medium grade galvanized with all fittings laid in floors /wall etc. complete all as specified and as directed.

S&F GI tube 20 mm dia medium grade galvanized with all fittings laid in floors /wall etc. complete all as specified and as directed.

S&F lagging to 15mm bore pipes used in internal water supply or plumbing all round with, 25mm thick bonded mineral wool preformed 'SNAPON' pipe section of density 144 Kg \cum conforming to IS 9842 along with chicken mesh wire netting 25 gauge, 20 mm mesh fixed in repairs complete all as specified and directed.

All as per item No 58 abore but for 20mm bore pipe.

Taking down of cement plaster of any description including racking out of joints hacking for keys and scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick on brick/stone masonry surfaces or other than fair faces in cement mortar 1:4 finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for rendering 10mm thick on brick/stone masonry surfaces or other than fair faces in cement mortar 1:6 finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for rendering 10mm thick on brick/stone masonry surfaces or other than fair faces in cement mortar 1:4 finished even and smooth (without using extra cement) in celling complete all as specified and directed.

Demolition of Brick/stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:4 Complete all as specified and as directed.

M&L for preparation of old plastered surfaces of ceiling and applying two coat of White Wash complete all as specified and directed.

M&L for Preparation of New plastered surfaces of ceiling and applying two coat of White Wash complete all as specified and directed.

M&L for Preparation of old plastered surfaces of wall and applying two coat of oil bound distemper complete all as specified and directed.

M&L for preparation of New plastered surfaces of wall and applying two coat of oil bound distemper complete all as specified and directed.

M&L for preparation old surface finishing walls with Acrylic Smooth exterior paint of required shade : New work/old work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

S & F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed.

S & F in Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms) complete all as specified and directed.

Dismantling of rain water pipe and sewage line pipe of any type and any size including fitting complete all as specified and as directed.

S & F for 100 mm Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors pipes are epoxy coated inside & outside complete all as specified and directed.

All as per item No 75 above but fixed to walls.

S & F for 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S & F for 100 mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches cast iron complete all as specified and directed.

S & F for 100 mm bore cast iron bends (any radius) with duck's foot or heel rest cast iron complete all as specified and directed.

S & F for Sockets (double) collars cast iron 100 mm bore complete all as specified and directed.

S & F for cast iron swan necks (or off- sets)/Floor trap upto 152 mm projection cast iron complete all as specified and directed.

S & F for Traps ‘P’ or ‘S’ cast iron in 100/125 mm complete all as specified and directed.

S & F for Cast iron cowls/vent cowl in 100/125 mm complete all as specified and directed.

Treatment of sunken floor slab comprises of the following specifications and steps complete all as specified and directed.:-

(a) Demolition of lean cement concrete up to any depth/bottom of sunken floor, any type of filling in sunken portion, removing debris & cleaning the bottom and vertical surface of wall up to the finished floor level.

(b) M&L for PCC (1:2:4) type B-0 using 12.5 mm aggregate stone aggregate, average 75 mm thick, maintain the slope of 1:40 towards the outgoing spout pipe, providing 32mm dia GI pipe, medium grade, spout projected at least 150 mm beyond outer face of wall including cutting of hole in RCC beam and brick wall.

(c) M&L for providing plaster 15 mm thick in CM (1:4) mixed with water proofing compound @ 3% by weight of cement to the floor and side walls upto the finished floor level.

(d) M&L for applying evenly two layers of industrial bitumen 85/25 @ of 1.20 Kg/Sqm in each layer over floor and vertical surface of sunken floors including cleaning the surfaces. Applying a layer of polymeric modified APP based membrane not less than 3mm thick, weighing not less than 3 kg per sqm, reinforced with polyester non- woven fabric (weighing not less than 150 gm per square metre), which shall be laid by torch application. Side overlaps of membrane shall be 100mm, ends laps shall be 150 mm and overlap joints shall also be sealed by torch application.

(e) M&L for providing 300 mm thick PCC (1:5:10), type E-2 using 40 mm graded brick aggregate,. The sunken portion of Nahani / floor trap and pipe joints shall be embedded in PCC (1:3:6) type C-0 using 12.5 mm aggregate stone aggregate. Necessary leakage shall be tested in CI pipes / joints /slabs / with filling the water for 72 hours and it shall be ensured that there is no leakage is found, else the above treatment shall be repeated till satisfactory result are found.

(f) PCC (1:2:4), type B-0, using 12.5 mm aggregate stone aggregate, 75 mm average thickness shall be laid at the top of slab maintaining a slope of 1:40 towards the outgoing pipe, surface shall be finished even and smooth with using extra cement.

Note :- (i) Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of GE. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing is included in the rates quoted above. (ii) All debris obtained from site will be thrown away out side MD land by contractor at his own expense. (iii) For payment purpose the plan area of sunken floor shall be taken into accounts.

S&F rotational moulded polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position of 500 ltrs capacity fixed with PVC tank all accessories be combined all rates Coated, complete all as specified in SSR Part I.

M&L for preparation of old steel surfaces over 10 cm in width or girth and applying one coat of synthetic enamel paint on old painted surfaces complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment (thick 0.63 mm) etc complete all as specified and directed.

S&F mild steel plates (plain or chequered) channels (thick 0.63 mm), square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

M&L for preparation of new steel surfaces over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L for 15mm thick rendering in Cement Mortar 1:4 on any faces of brick or concrete surfaces of walls & finishing the surface even and smooth without using extra ement, complete all as specified and directed.

M & L for 10mm thick rendering in Cement Mortar 1:4 on any faces of brick or concrete surfaces of walls & finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for applying two coats of white wash on newly plastered surfaces on wall including preparation of surface complete all as specified and directed.

M&L for Preparation New undecorated surface of walls and applying one coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

S&F 1000 Ltr capacity PVC water storage tank (cylindrical vertical with closed top ) and fixed in position all as specified in SSR Part -I complete all as specified and directed.

S&F PTMT ball valve high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule 20mm dia.

S & F bend suitable for 110mm dia PVC (SWR) pipe complete all as specified and as directed

S&F 110mm bore PVC (SWR) junction, single (single T) equal or unequal with door access complete all as specified and directed.

M&L for PVC (SWR) vent cowl for 75 mm dia complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, fixed to complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, fixed to wall complete all as specified and directed.

M&L for mild steel framed work for such as grills, gratings, etc..with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings, removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specified and directed.

Taking down MCCB, MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

Disconnecting unserviceable sub main wiring/service connection of any size and including steel conduit and accessories and removing from site and making good the disturbed surfaces complete all as specified and directed.

M&L for point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLSH insulated un-sheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC FRLSH insulated un-sheathed copper conductor single core multi stranded flexible cable (green colour) as earth lead in and including cable 1100 volts grade including casing and capping/conduit (ISI marked) including sunk cast iron/pressed steel terminal boxes, junction boxes, other boxes made from thick sheet of suitable sizes for mounting of switches, sockets, fan regulators, light fittings etc. covered with plastic laminated sheet or PVC gang box 2 to 8 way as per site requirement fiing in surface mount or concealed including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified.

All as per item No 105 herein before but wiring with 1.5 sqmm copper wire (FR-LS-H) and 1.5 sqmm earth wire for socket outlet 3 pin 5 amps on same board.

All as per item No 105 herein before but wiring with 1.5 sqmm copper wire (FR-LS-H) and 1.5 sqmm earth wire for socket outlet 3 pin 5 amps on independent board.

All as per item No 105 herein before but wiring with 2.5 sqmm copper wire (FR-LS-H) and 1.5 sqmm earth wire for socket outlet 6 pin 15 amps on independent board.

S&F switch piano flush button single pole, one way 5 amps complete all as specified and directed.

S & F switch socket combination 2 in 1,5A, flush type complete all as specified and directed.

S & F switch socket combination 5 pin 16A, flush type complete all as specified and directed.

S&F of distribution board single pole & neutral with 200 Amps rated bus bar, for double door IP-42 DB's, made out of sheet steel enclosure, recessed type, factory made powder coated 8 way -240 volts suitable for housing MCB's and isolator's complete in all fixing material/accessories etc complete all as specified and directed.

S&F MCB's single pole 240 volts 6 to 32Amps 10 KA 'C' curve series, all as specified and as directed by Engr -in-Charge.

S & F of MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

M & L Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and directed.

Supply and fix LED Bulb 9 Watt all complete all as specified and directed.

S&F LED, 20 Watts, 4 ft, fittings complete with all accessories for mounting light fittings complete with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body complete all as specified and directed.

Supply and fix ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body complete all as specified and directed.

S&F exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230v , 50HZ , RPM 1200, Copper winding of sweep 300mm, complete all as specified and directed.

S&F 09W/10W Bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

M&L for wiring for circuit/submain wiring along with earth wire with the following sizes of FRLSH PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing caping of size 2x6 sq. mm + 1x4 sq. mm earth wire complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60x60cmx6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge lead of the plate not less than 1.5 mtr below normal ground level, connected galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in Electrical plate No 3 connected to earthing test point including earth work, all as specified or indicated including testing on completion, complete all as specified and directed.

S&F electric water Heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 50 liter ,BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc, complete all as specified and directed.

S&F of distribution board single pole & neutral with 200 Amps rated bus bar, for single door IP-42 DB's made out of sheet steel enclosure, recessed type, factory made powder coated 4 way -240 volts suitable for housing MCB's and isolator's complete in all fixing material/accessories etc complete all as specified and directed.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 sq. mm nominal cross section in service connections, all as specified and directed by Engr-in-Charge.

Taking down carefully copper/ aluminium unserviceable/ perished cable any size ,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specified and directed.

Supply and fix PVC insulated, armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 sq, mm 3.5 Core, complete all as specified and directed.

Supply and fix MCCB 4 Pole, 415 V, Adjustable type, 200 Amps with breaking capacity 36 KA, complete all as specified and directed.

M/S GHULAM AHMAD BABA (BID ID -3457063)

M/S ABDUL AZIZ MIR (BID ID -3461326)

M/S MIR BUILDERS (BID ID -3457047)

M/S SUMJI BROTHERS (BID ID -3457104)

Bidder Name

M/S SUMJI BROTHERS

M/S MIR BUILDERS

M/S ABDUL AZIZ MIR

M/S GHULAM AHMAD BABA

Concept Engineering & Constructions