RequiredExperience with Government Bid to RA enabled No Track Suits - Sports ( 500 pieces ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) UTILITY UTILITY Unisex * COMPONENTS Components Complete Set consisting of Upper and Lower * MATERIAL Fabric ( Composition ) Polyester Blended With Viscose Polyester Blended With Viscose Percentage of Blending ( in case of Blended Fabric ) Polyester 65 % and Viscose 35 % Polyester 65 % and Viscose 35 % 1/8 Mass ( gram per square mtrs ) 220 220.0 Fabric Construction Knitted Knitted Weave ( In case of Woven Fabric ) Plain Plain Any other weave as per buyer's requirements ( in case weave is other than already mentioned above ) - * Knitting ( In case of knitted Fabric ) Interlock Knitted Interlock Knitted Ends per dm - * Picks per dm - * Courses per dm - * Wales per dm - * Count of knitting yarn - * Raising at inner side of Main Fabric Yes Yes Upper Lining Yes Yes Lower Lining Yes Yes Lining Material 100% Polyester Mesh 100% Polyester Mesh Mass of Lining (Gram per Square Meter) Not Applicable * Netting mesh No of holes on base & bias within 625 Square millimeter Not Applicable * Technical Requirements of Slide Fastener for Upper Closing No No Technical Requirements of Slide Fastener for Pocket Closing ( For Pockets with Slide Fastner for closing ) No No Slide Fastners are BIS Marked Not Applicable Not Applicable Width of Tape Elastic at Waist of Trouser 4.0 cm * Width of Tape Elastic at Bottom of Upper 4.0 cm * Technical Requirements of No No 2/8 Waist Band Waist Draw Cord Polypropylene Cord of 4mm dia * Draw Cord Ends Fused * Breaking Strength of Draw Cord 340 N minimum * Sleeve Ends ( Cuff ) Elastic Tape * Upper provided with Piping Yes Yes Lower provided with Piping No No Piping Fabric- Composition 100 percent Polyester * Piping Fabric- Any other material as per buyer's requirements ( Other than mentioned above ) - * Piping Fabric Mass ( gram per square mtrs ) 90 90 Embroidery Thread Not Applicable Not Applicable SIZE Size Extra Large (XL) Extra Large (XL) DIMENSIONS OF UPPER Width Across Chest 25 mm below under arm 57.5 cm ( Extra Large ) * Width Across Bottom Opening (relaxed) 50 cm ( Extra Large ) * Length at front from top of collar to bottom 70 cm ( Extra Large ) * Sleeve length (from center of back to bottom of sleeve 89.5 cm ( Extra Large ) * Sleeve opening relaxed ( Cuff ) Width 9 * Front Neck Drop 9 * Back Neck Drop 2 * Length of Slide Fastener 68 cm ( Extra Large ) * DIMENSIONS OF LOWER Side Seam Length 109.5 cm ( Extra Large ) * Waist relaxed ( Width Across ) 47 cm ( Extra Large ) * Waist stretched (Width Across ) 57.5 cm ( Extra Large ) * Seat/Hip ( 15 cm below 57.5 cm ( Extra Large ) * 3/8 waist band) Thigh (at Crotch) ( Width Across ) 38 cm ( Extra Large ) * Bottom Opening ( Width Across ) 25 * Front rise including waist band 30 cm ( Extra Large ) * Back rise including waist band 40 cm ( Extra Large ) * Length of Waist Tying Cord 154 * Bottom Fold (Hem) with full turn in(cm) 2.5 * POCKETS Number of Pockets (Upper) 2 Side Pockets 2 Side Pockets Size of Side Pockets- Upper ( Length X Width ) ( cm ) 18 X 20 cm * Size of Inside Pocket at Chest- Upper Not Applicable * Side Pocket opening - Upper 15.0 cm * Side Pocket Closure with Slide Fastener -Upper No No Number of Pockets (Lower) 2 Side Pockets 2 Side Pockets Size of Side Pockets - Lower ( Length X Width ) ( cm ) 18 cm X 20 cm * Side Pocket Opening- Lower 15 * Pocket Closure with Slide Fastener - Lower All Pockets with Slide Fastener All Pockets with Slide Fastener Material of Pockets Main Basic Fabric * COLLAR Collar Type Stand and Fall Type
RequiredMade of two layers of self material * Collar Reinforcement Without Reinforcement * SLEEVE Sleeve Type Reglan Sleeve * PIPING Position and Dimensions of Piping on Upper - * Position and Dimensions of Piping - * 4/8 on Lower STITCHING Sewing Thread 125 d tex X 3
RequiredPolyester * Raw edges
Requiredif any shall be bound by overlock stitching Yes * Waist band stitching of Upper Stitched in three rows with chain stitch on the elastic * Sleeve Bottom (Cuff ) Stitching Stitched in three rows with chain stitch on the elastic * Waist band stitching of Lower Stitched in three rows with chain stitch on the elastic * Lining seams Inverted * Bartack Stitching ( Reinforcement Stitching ) at stress bearing areas Pocket opening
RequiredCentre of Waist Band Seam and bottom hem and other stress bearing areas * Tunnel at Waist Band for Lower Two holes stitched to allow the draw cord with insertion free movement * Stitches per dm ( min ) 36 * COLOUR/PRINT Colour Light Blue * Multicolour Contrasting Pannels Any other colour as per buyer's requirements - * Sublimation Printing (for 100 % polyester only) Sublimation Print as per buyer's requirements Sublimation Print as per buyer's requirements Sublimation Print as per buyer's requirements - * Colourfastness to Light ( IS 2454 ) 5 * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3)) Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * Colourfastness to Rubbing ( IS 766 ) Dry- 4/Wet- 3 * Colourfastness to perspiration ( IS 971 ) 4 * Colour of Mesh Lining Same as colour of the base fabric Same as colour of the base fabric 5/8 Any other colour of Mesh Lining as per buyer's requirements - * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3))- Mesh Lining Not Applicable * Colourfastness to perspiration ( IS 971 )- Mesh Lining Not Applicable * Colour of Piping Material Blue * Any other colour as per buyer's requirements - * OTHER REQUIREMENTS Pilling Resistant [after 5 hours Test as per IS 10971 (Part 1)]
Requiredmin 4 * Dimensional stability to washing
RequiredShrinkage or Elongation Percentage
Requiredmax ( IS 2977 latest)
Requiredin lengthwise and widthwise direction 3 3 LOGO AND MARKING Logo/Totem Marking As per buyer's requirements As per buyer's requirements Type of Logo Printed Printed Number of Logos on Upper Not Applicable Not Applicable Number of Logos on Lower Not Applicable Not Applicable Size
RequiredDesign and Location of Logo as per buyer's requirement - * TEST REPORT Availability of Test Report from designated AHSP NABL/ILAC accredited or Central Government Lab to prove conformity of products to the specification No No Test Report No - * Test Report Date - * Name of the Lab - * Address of the Lab - * 6/8 Test reports to be furnished to buyer on demand
Requiredif claimed to be available Not applicable * ADVANCE SAMPLE Agree to provide Advance Sample(s) for buyer's approval before commencement of supply Yes Yes * Specifications highlighted in bold are the Golden Parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer.
