PLASTERING AND PAINTING ON BOUNDARY WALL INSIDE TECH AREA, VIP ROUTES INCLUDING NECESSARY B/R WORKS AT AIR FORCE STATION PALAM, DELHI CANTT-10

Amount

Taking down cement plaster on brick or concrete wall surfaces etc., including raking out joints, hacking for key , scrubbing down with water,etc. complete all as specified and directed..

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:4, to be finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying two coats of 100% Premium acrylic emulsion paint (Make: Apex of Asian or equivalent in Shalimar/Berger paints) having VOC less than 50 gm/ltr and UV resistance as per IS 15489-2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.9 litre /10 sqm over New surfaces complete all as specified and directed (Note: Complete Qty of Paint will be submitted to Engr-In-Charge and work must be got executed through authorised Applicator of manufacturer and shall be got approved from GE before commencement of work.) .

M&L for complete removal of existing treatment of old decorated external surface of walls by electrically operated grinder including necessary scaffolding etc and applying two coats of exterior emulsion paint (Make: Apex of Asian or equivalent in Shalimar/Berger paints) over one coat of primer after applying 2 mm thick wall care putty (Make: JK/BIRLA/ASIAN) to obtain smooth finishing surface etc. complete all as specified and directed.( Note: Complete Qty of Paint will be submitted to Engr-In-Charge and work must be got executed through authorised Applicator of manufacturer and shall be got approved from GE before commencement of work.)

M&L for preparation of concrete or plastered surface, plain/kerb stone moulded over 10cm width or girth by cleaning brushing etc. and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.( Note: Complete Qty of Paint will be submitted to Engr-In-Charge and work must be got executed through authorised Applicator of manufacturer and shall be got approved from GE before commencement of work) .

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and as directed.

S& F for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, with grey cement and pigment, set jointed and pointed in neat cement slurry in floors laid over 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L Glazed ceramic coloured tiles (colour & shade as approved) of size 300x200x7mm thick in vertical surfaces as in skirting and dado, set and jointed in neat cement slurry, over 10mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

Supply and Fixing in repair pre cast cement concrete jallies, 35 mm thick, type B0 1:2:4 (using 12.5 mm graded crushed stone aggregate) including wire fabric set and jointed in cement mortar 1:6 complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quions,arches,pillars etc. complete all as specified and directed.

Material and labour for brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for preparation of old painted surfaces of steel and Iron surfaces of any description ,n.exc 10 cm in width or girth when unconnected with other painting or when painted in a different tint and applying one coat of synthetic enamel paint complete all as specified and directed.( Note :Complete Qty of Paint will be submitted to Engr-In-Charge and work must be got executed through authorised Applicator of manufacturer and shall be got approved from GE before commencement of work.) .

Material and labour for preparation of old painted surfaces of steel and iron surfaces of any description not otherwise described , over 10 cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed .( Note :Complete Qty of Paint will be submitted to Engr-In-Charge and work must be got executed through authorised Applicator of manufacturer and shall be got approved from GE before commencement of work) .

Dismantling plain or corrugated steel sheeting, any gauge,thickness, including nainital or similar pattern roof coverings complete all as specified and as directed.

S&F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel seet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall ,fixed with self taping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F Steel Rolling shutters,with ball bearing including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated complete gear operated type with bevel gear box and crank handle with thickness of laths as 01 mm complete all as specified and directed.

M&L for two coat of synthetic enamel paint over a coat of red oxide after preparation of new steel surfaces of any description,over 10 cm in width or girth complete all as specified and directed .( Note :Complete Qty of Paint will be submitted to Engr-In-Charge and work must be got executed through authorised Applicator of manufacturer and shall be got approved from GE before commencement of work) .

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each including cutting holes in walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.50 Sqm but n. exc 4.0 sqm each including cutting holes in walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and directed.

S&F anodised aluminium powder coated frame (minimum thickness of powder coating 50 micron) for door, windows, ventilators, partition wall with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed

S&F anodised aluminium powder coated door shutters, aluminium section weighing 0.55 Kg/m (Thickness or powder coating not less than 50 micron), including neccesary joining cleats, glazing clips,rubber neoprene packing, handle 2 nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handle 2 nos in each window , anodised aluminium fitting such as peg stays150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and directed.

S&F aluminum grill of design and pattern as approved including aluminium beading complete all as specified and as directed.

M&L for 12mm thick prelaminated particle board, exterior grade, prelaminated both side with decorative choice laminations & fixed with screws to timber frame work complete all as specified and as directed

S & F Door closer hydraulically regulated designation No 3 ,universal type, suitable for door shutter of 851 to 1000 mm in width of Aluminum body (die cast) and of weight between 61 to 80 kg complete all as specified and as directed.

S & F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other party made of mild steel heavy duty complete all as specified and as directed.

S & F mild steel mortice lock, vertical type, size 100mm, 4 levers complete all as specified and as directed

S&F aluminium anodised, barrel tower bolt of extruded section, 150mm length of bolt and fixed with screws,complete all as specified and directed.

S&F aluminium door stopper double legged with rubber shoe 75mm long fixed to door shutters complete all as specified and as directed.

Demolition of concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed.

M&L for Stone kerb of roughly squared stones of size 20cm x 30cm, dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20 mm for the rest of surfaces jointed in cement mortar 1:6 with sand stone and struck flush,chamfered angles, weathering or singly round throating etc complete all as specified and as directed.

M&L for applying two coat of rubber chlorinated high build coating synthetic enamel paint on concrete surfaces over a coat of primer including necessary preparation, complete all as specified and as directed.( Note :Complete Qty of Paint will be submitted to Engr-In-Charge and work must be got executed through authorised Applicator of manufacturer and shall be got approved from GE before commencement of work) .

M&L for old external surface of walls including necessary scaffolding etc and applying one coat of exterior emulsion paint (Make: Apex of Asian or equivalent in Shalimar/Berger paints) to obtain smooth finishing surface etc complete all as specified and directed. Note : 1.Complete Qty of Paint will be submitted to Engr-In-Charge. and work must be got executed through authorised Applicator of manufacturer and shall be got approved from GE before commencement of work. Note for item no 3 ,4 & 35 : MOU with Manufacturers of Paints : Irrespective of whatever specified elsewhere in tender documents, the work ( for item no. 3, 4 & 35 of Sch’A’ ) shall be executed through authorized applicator of manufacturer of Asian paints(Apex) / Berger paints / Shalimar paints only. Tenderers are deemed to have entered into a triparty agreement between tenderer, said manufacturer of Paints and their authorised Applicator and a valid MOU on Non Judicial Stamp paper of Rs. 100/- towards same is to be submitted within 15 days to GE from date of commencement of work as mentioned in Work order no 1 provided by GE. In case of non-submission of MOU within 15 days from date of commencement of work (stated in WO No 1) by tenderer to the GE , same shall be immediately brought to the notice of Accepting officer and contract shall liable to be cancelled on default of tenderer. MOU shall also cover the Guarantee and defect rectification during guarantee period and the aspect that work will have to be completed within stipulated time period mentioned in contract by the authorised applicator of paints. Contractor is liable to collect the details of work from Engr-in-Charge on weekly basis and submit completion report after assigning of location(s) for execution of work to Engr-in-charge as directed. Authorised Applicator of above mentioned Paint Manufacturers shall have valid authorization letter from the manufacturer issued not earlier than 60 days from the Bid submission start date of this tender.

M&L for Providing and applying plaster of paris putty (Make: JK/BIRLA/ASIAN) of 02 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

SHEELSONS ENTERPRISES

SHYAM ENTERPRISES

M/S Satyam Associates

M/S Parshant Associates

Atish Builders LLP

YP INFRA

PIONEER REFRIGERATION AND ELECTRICALS