Construction of High Security Boundary wall check post in Judical Complex Sector-12 Karnal

Amount

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres.(HSR 6.6)

Dismantling brick work, tile masonry or tile lining and tile terracing . (b) in cement,[HSR 8.5(b)]

Cement concrete 1:6:12 with stone aggregate 40mm nominal size in foundation and plinth (HSR 10.32)

Cement Concrete 1:4:8 with stone aggregate 20mm nominal size in foundation and plinth. [HSR 10.38]

Cement concrete 1;2;4 with stone aggregate 20mm nominal size in first storey upto 4 metres above plinth level (HSR 10.59)

Cement concrete 1 : 1½ : 3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respects. [HSR 10.82 + 10.95 (a)]

Cement concrete 1 : 1½ : 3 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20 cm thickness (straight and curved) beams,girders, stairs, columns, (square or rectangular) battens and lintels etc excluding steel rainforcement but including centring and shuttering, laid in position, complete in all respects.[HSR 10.86 + 10.95(a)]

Damp proof course 25 mm thick of cement concrete 1:2:4 using stone aggregate without bitumen coats. [HSR 10.115]

First class brick work laid in cement sand mortar 1 : 4 in foundation and plinth (HSR 11.4)

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level ( HSR 11.9)

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, BELL, RAK, SIMPOLO & JOHNSON. (HSR 14.89)

Providing & fixing vitrified tiles of size 600mm x 600mm of approved make in skirting/dados laid in any pattern as specified over base of 12mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: NITCO, KAJARIA, SOMANI, ORIENT, BELL, RAK, SIMPOLO & JOHNSON. (Double charged tiles shall be used as approved by Engineer in charge. (HSR 14.90).

12 mm thick cement plaster 1 : 4 on walls ( HSR 15.5 )

12 mm thick cement plaster 1:6 on walls [HSR 15.7]

15mm thick cement plaster 1:4 on the rough side of single or half brick wall. (HSR 15.10)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surface. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.25).

Painting two coats with plastic emulsion paint on walls on new work to give an even shade. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.30)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)].

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81).

Factory manufactured solid flush door shutters, with block board core as per I.S.No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot pressed, conforming to I.S.2202 part I and II , fixed in position including iron hinges, screws, chocks/ cleats and stops, etc.(excluding the cost of any fittings other than specified above, but including labour for fixing the same in position) (a)commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges. [HSR 17.93(a)(iii)] 35mm thick

Wrought iron and mild steel(using angles, flats ,square bars , tee and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Pressed steel sheet frames (chowkats ), consisting of 2mm thick steel sheet of the specified section,including iron lugs(hold fasts) iron hinges conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for fillings in the frame, and cement concrete 1:3:6 for lugs complete (HSR 18.34) b) Door and window frame of size 76 mm x 38 mm with 35 mm wide single rebate

Dismantling of road including soling and wearing coat, screening and stacking of old serviceable material, complete in all respect. (HSR 24.37)

Extra for making sharpness of 60x6x6mm angle (N.S)

Recovery items:- The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Dismantiling of bricks in the DNIT. In case it is not possible to use this material on the work, the agency can take away this material after approval from employer. This material will be issued at the price quoted by the agency. However the reserve price is as under:- i) Good Bricks @ 4.50/- Each

ii) Brick Bats @ 450/- cum Note:- All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this building. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price. Note:- 1. In case of any difference in the unit & nomenclature of any of the HSR Items of Civil, P.H. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (make/brand exhibited in HSR and exhibited in approved standard document) as approved by Engineer-in-charge, while executing various items/works at site.

THE SHILPA CO OP LC SOCIETY KTL