Construction of Primary Health Center DIHRI BISHRAMPUR in Vill DIHRI BISHRAMPUR, GP MAHUARI, Block HUSAINABAD, District PALAMU under Zila Parishad, Palamu.

Earth work in excavation in foundation trenches in Hard soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance up to 50 M. including all lifts, leveling, ramming the foundation trenches, removing roots of trees,, shrubs all complete as per approved design, building specification and direction of E/I.Extra for earthwork in herd soil es per specificatlon and directian of E/I(Vide cleseitfioetion of soil item_B)

Filling in foundation trenches and plenth in layers not exceeding 150 mm. thick well watered ,rammed ,fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume).

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering texes royalty all complete as per building specification and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth & floor including ramming & watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing and laying in position cement concrete of specified grade |excluding the cost of centering and shutfering All work up to plinth level:1:2:4 (1 cement: 2 coarse sand (zone-1) :4 graded stone aggregate 20 mm nominal size)

Providing and laying in positionspecified grade of reinforaed cement concrete, excluding the cost of centering, shutterhe. finishing and reinforcement- All work upto plinth level. 1.5:3 (1 cement: 1.5 course sand (zone-1): 3 graded stone geregate 20 mm nominal size)

Reinforded cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajas, lintels, bands, plain window sills, staircases and spiral stair cases

Reinforced cement concrete work in wals (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets column pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering& finishing and reinforcement :1:1.5:3 cement: 1.5 coarse sand (zone-l):3 graded stone ag8regate 20 mmnominalsize)

Reinforded cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajas, lintels, bands, plain window sills, staircases and spiral stair cases Jabove plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:15:3 cement: 1.5 coarsesand(zone-l):3 graded stone aggregate 20 mm nominal size).

Reinforded cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajas, lintels, bands, plain window sills, staircases and spiral stair cases Jabove plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:15:3 cement: 1.5 coarsesand(zone-l):3 graded stone aggregate 20 mm nominal size).

Reinforded cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajas, lintels, bands, plain window sills, staircases and spiral stair casesJabove plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:15:3 cement: 1.5 coarsesand(zone-l):3 graded stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc. and removal of form for foundation, footings, bases of columns etc. for mass concrete.

Centring and shuttering including strutting, propping etc. and removal of form for lintel, beams, plinth beams, griders, bressumers and contilevers.

Centring and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts

Centring and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform.

Providing TOR Steel reinforcement of 10mm ,12mm ,& 16mm. dia bars as per apporoved design and drawing excluding carrige of bars to work site ,cutting ,bending , and bending with annealed wire with cost of wire , removal of rust , placing the rods in position all cpomplete as per building specification and direction of E/I .TMTC-500 8mm dia

TMTC-500 8mm dia

TMTC-500 10mm dia

TMTC-500 12mm dia

TMT-500 16mm dia

Providing designation 75B brick work in C.M.(1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. Thick morter joints, cost of screening, materials, scaffolfing, raking out joints to 15mm. Depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 125 mm thick reinforcement designation 75 A brick work in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials, scaffolding raking out joints to 15 mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Providing 12 mm , cement plaster (1:4)with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water ,scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6 mm , cement plaster (1:4) in ceiling with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water ,scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing and applying WHITE cement based putty 1 mm thickness over plastered surface to prepare the surface even and smooth complete

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Providing 12 mm , cement plaster (1:4)with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water ,scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such shades except white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622/ ISO 13006, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. complete Size of Tile 600 x 600 mm

Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622/ ISO 13006, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. complete Size of Tile 600 x 600 mm

Providing and laying 25mm. thick kotah stone tiles in risersof steps, skiiting and pillars of approves size, texture and colour laid cover 12mrn. thick cement mortar (1:3) and.loined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolilthic finish with approved quality of carborandurn stone including cost of curing, taxes and royaliy all complete as per building specificationand direction of El.

Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.)

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames einforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin-charge 9.117.1 Extruded section profile size 48x40 mm

24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (±0.2 mm) with inbuilt edging on both sides. The styles and rails mitredand joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filledwith a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).

Supplying fitting and fixing good quality well dressed and second local wood work. In chaukhat in door , windows skylight , fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality of the surface bulting walls and lintels all complete as per building specification and direction of E/I

Supplying, fitting and fixing 30mm thick solid core decorative single leaf flus door shutter with both decorative vannered with block board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminium fitting such as hings, tower bolts , handle , cleats and sand blocks taxes all complete as per building specification and direction of E/I

Supplying, fitting and fixing fully glazed steel door, windows or ventilators of standard Z and mullion steel sections and size as per IS 1038 joints met and welded with 100x16x3mm M.S Lugs fixed in cement concrete 1:2:4 blocks 15x10x10 cm size including cost of oxidized iron fittings with hinges handle per steps catch springs 3mm thick plain glass panes with aluminium beads and inner frame fixed with lugs with 20mm long 6.3mm G.I counters sunk machine screw and nuts and applying a coat of red lead paint, carriage to work site, hosting & placing in position in all stories and taxes all complete as per building specification and direction of E/I.

Supplying.fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20X10X2 mm. at 100mm. Centres and braced with M.S. flat diagonals 20 X 3mm with top ad botom rails of T. iron 40x40x6mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing 150mm Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm aporn including cost of earthwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in CM(1:3) With Punning over Exposed surface all complete as per building specification and direction of E/I

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin-Charge.80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.

Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. 'p' trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S equivalent make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixed a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. 580 mm. long With 10 lit. low level P.V.C Cistem

Supplying, fitting and fixing 40mm high vitreous white glazed ware E.W.C. with "p" trap of parry/hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make and complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle cock of approved qualty weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and White/black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide prining, all complete as per specification and direction of E/I.With s trap 10 lit. low level P.V.C cistern

Supplying, fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Supplying fitting and fixing white glazed fire's clay sink of approved make with overflow arrangements supported on C.I. or R.S. painted brackets 40mm. dia C.P. brass waste with C.P. brass chain and rubber plug 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one endand 15mm C.I. body brass spindle bib cock of approved quality of weight not less than 450grams. including cutting wall and making good the same etc. all complete as per specification and direction of E/IKitchen sink 600 mm x 450 mm x 250 mm

Supplying, fitting and fixing H.C.I. pipes with ear of approved make conforming to I.S.I. 1729 including supplying nails and bobins short pieces, cutting loose collars, lead and yarn for making lead caulked joints, cutting pipes to size including earth woek or scaffolding where necessary etc. all complete as per specification and direction of E/I.100mm dia

75mm dia

Supplying and fixing H.C.I. fittings of approved make confirming to I.S.S. 1729 including supplying nails and bobines lead and yarn from making lead caulked joints including earthwork or providing scaffolding as the case may be all complete as per specification and direction of E/I.(B) H.C.I. Heal Rest bend (i)100 mm dia (wt. 5.5 kg. app)

80 mm dia (wt. 4 kg. app)

(D) H.C.I. double junction with door and ear (i) 100 mm dia (wt. 15.5 kg. app)

(ii)80 mm dia (wt. 15.5 kg. app)

(J) Floor trap with grating (i)100mm dia

(K) Norton patent H.C.I. Cowel (i)100mm dia (wt. 3.25 Kg appx.)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 12.41.2 (110 mm diameter)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single pushfit Coupler 110 mm(12.42.2.2)

Single tee with door 110x110x110 mm

Bend 87.5°110 mm bend

Shoe (Plain) 110 mm Shoe

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 15 mm dia (18.8.1)

20 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.25 mm nominal outer dia Pipes (18.7.3)

32 mm nominal outer dia Pipes

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :100 mm diameter S.W. pipe (19.2.1)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :15 mm nominal bore(18.18.1)

25 mm nominal bore

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (19.4.1/19.4.1.1)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying in position cement concrete of specified grade |excluding the cost of centering and shutfering All work up to plinth level:1:3:6 (1 Cement: 3coarse sandzone-ll):6 graded stone aggregate 20 (i) Sloping portion 1:20

Providing designation 75A brick work in C.M (1:4) in foundation and plinth with approved quality of clean coarse sand of F.M 2 to 2.5 including providing 10mm th mortar joints, cost of screening materials , raking out joints to 15mm depth , curing , taxes and royalty all complete as per building specification and direction of E/I

Providing 12mm thk. Cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I.

Providing 19mm thk. Water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other water proofing compound including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I.

(i) C.I. cover and frame 300 x 300 mm inside

(ii) S.C.I. plain bend 100 mm dia

(iii) S.C.I. Tee 150 mm dia

Supplying all materials, labours and tools and equipment for drilling 200x150 x125mm dia bore well in any kind of soil and rock by using DTH Super Rig machine and ball hammer technology inclusive of mobilization, demobilization, demobilization of rigs air compressor all accessories of rigs tool and plant labour etc. all complete job including transportation charge.(a) 0.00 to 50.00 M below G.L.

(b) 50.00 to 125.00 M below G.L.

Supplying, assembling, lowering and fixing in vertical position in bore well, un-plasticized PVC medium well casing (CM) pipe of required dia, all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia.

Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, all as per requirement and direction of Engineer-incharge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe,Nremovable as per requirement, all complete for borewell of 150Nmm dia.

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts required size complete. 150 mm clamp.

Supplying fitting and fixing of KSB/KIRLOSKER/CRI make 1.00/1.5HP Submersible pump set having head of 135 metre including all taxes, royalty, etc.all complete job as per direction of E/I.

Supplying of 3 core 4 sq. mm flat copper cable of Finolex make for pump set connection with panel board including labour cost and making conneting etc. all complete.

Cost of one of ISI marked extre deep indiaa mark -II hand pump confirming to IS 13287 :1992 with latest amendment no Is 1to 6 complete with all ......do....do......E/I.

Point Wiring in PVC Conduit, with Modular type Switch:- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.Group C

Twin control Point Wiring in PVC Conduit, with Modular type Switch:-Wiring for twin control light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with 2 way modular type switch, modular plate, suitable size of GI box etc as required.

S/F Ceiling Rose :- Supplying and fixing 2pin 5 amp ceiling rose on the existing junction box/wooden block including connection as required etc.

S/F Modular type electronic fan regulator :- Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

Supply, fitting, fixing and testing of 1200mm Sweep, double ball-bearing, 2 canopy ceiling fan including connection with 1.5 sq mm copper wire, down rod all accessories as required.

S.I.T.C of following rating surface mounted LED tube lightfitting suitable for 230V 50Hz, single phase supply etc. compete as required.

20w/22w LED tube

Supplying and fixing batten/ angle holder including connection etc. as required.

10 Watt LED Bulb

S.I.T.C of following rating LED post top lamp made in die cast aluminium housing with decorative claer/opal acrylic diffuser on existing pipe including connection with 1.5sq.mm. copper conductor etc all complete as required. 45w LED Post top lamp opel

12" (300mm) Exhaust fan

Installation of exhaust fan upto 450mm sweep in the existing opening, including making the hole to suit the size of he above fan making good the damage, connection, testing, commisionig etc as required.

S/F light plug point with modular type accessories :-Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc, as required.

S/F light plug point with modular type accessories :-Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

S/F Modular type blanking plate :-Supplying and fixing modular blanking plate on the existing modular plate & switch box but excluding modular plate as required.

S/F T.P. MCB DB:- Supplying and fixing following way three pole & neutral ,sheet steel, MCB distribution board, 415 volts, onsurface /recess, complete with tinned copper bus bar, neutral bus-bar, earthbar ,dinbar, interconnections, powder painted including earthing etc. as 4 Way (4 + 12), Double Door, Horizontal type required.

6 Way (4+18) Double Door, Horizontal type

SUBMAIN WIRING COPPER IN PVC CONDUIT Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor single core cable in surfacce/ recessed medium class PVC conduit.4R X 16 sq. mm + 2R x 6 sq.mm Earth Wire

CIRCUIT WIRING COPPER IN PVC CONDUIT FOR 5A & SWICTH BOARD:-Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of PVC insulated copper conductor single core cable in surfacce/ recessed medium class PVC conduit. 2R X 4 sq. mm + 1R x 4 sq.mm Earth Wire (Sockets)

2R X 2.5 sq. mm + 1R x 2.5 sq.mm Earth Wire (Switch Boards)

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed armoured electrical cable with aluminium conductor for working voltage upto 1.1 KV etc as required. 3.5c x 95 sq.mm

Cairrage of Materials (1) Cement

(b) Sand

(Ć) Local Sand

(Ć)Stone Chips

(D) Briks

€ Steel

LABOUR CESS @ 1%

Supplying fitting and fixing panel board with MCB voltmeter main with starter having starting capacity and running capacity with indicator etc. all complete required for submerfible pump set.

provision and supplying of sutaible arrangment of MS plate or reducer socket for installation of extra deep wel Hand pump......do..........do.......E/I.

Supplying, Lowering of uPVC pipe of 50 mm dia heavy duty including of required fittings,solvent etc.all complete job as per direction of E/I.

RATE ANALYSIS OF SLDB

FIRE FIGHTING CYLINDER(MR)

LABOUR CESS @ 1%

Please Enable Macros to View BoQ information