SPECIAL REPAIR OF BLDG NO 191 AND 192 (06 QTRS) AT THIMAIYA MANSION AND SPECIAL REPAIR TO OFFICER MD ACCN BLDG NO P-12 IN KRISHNA ENCLAVE OF HQ MB AREA UNDER GE (W) JABALPUR

Amount

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store, of size 20mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store, of size 25mm bore of pipe complete all as specified and as directed.

Dismantling of water tank of any description of capacity exc. 250 litres but not exc. 500 litres, removing to store or from the site complete all as specified and as directed.

Dismantling of water tank of any description of capacity exc. 500 litres but not exc. 1000 litres, removing to store or from the site complete all as specified and as directed.

Removing old tarfelt, all loose dirt,old roof tiles,including taking down cement plaster, cleaning the concrete surface with wire brush including removal & cleaning of vegetation, fungus,moss, small trees etc from the roof top , removing the strips of lightening conductor item including refixing the same after repair work complete all as specified and directed by Engineer-in-Charge.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.50 sqm each and removal complete all as specified & directed.

Taking down shutter of any description n.exc 1 sqm each and removing from site complete all as specified and directed.

Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each and removing form site.

Taking down shutters of any description n.exc 1.00 sqm each resecuring, easing , adjusting and re-fixing in same opening after minor repairs including all necessary fittings complete all as specified and as directed .

Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each resecuring, easing , adjusting and re-fixing in same opening after minor repairs including all necessary fittings complete all as specified and as directed.

Taking down cement plaster etc on brick walls/ concrete (ceiling) surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of unserviceable materials to out side of MD land complete all as specified & directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

Dismantling of Stone slabs and kota stone, Granite, Chequered tiles, Paver block, etc of any description or thickness in floors, aprons etc. laid bedded and pointed in any cement mortar complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removal of debris to out side MD land complete all as specified & directed.

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cm in thickness (below or above ground level) including removal of debris to out side MD land complete all as specified & directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of AC (corrugated or semi corrugated etc.) sheets including ridges in roof coverings complete all as specified & directed.

M&L for 10mm thick rendering in CM (1:3) mixed with liquid water proofing compound as per Manufacturer's instructions, on concrete roof surface, finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed. (Note- Liquid WPC will be measurd and paid for separately as "Supply only")

M&L for 10mm thick rendering in CM( 1:6) on internal surfaces of wall, finished even and smooth without using extra cement complete all as specified & directed.

M&L 15 mm thick rendering in CM 1:4 on external surfaces of walls & top surfaces of chajja/roof, mixed with liquid water proofing compound as per Manufacturer's' instructions, surface finished even and smooth without using extra cement complete all as specified & directed. ( Note : Liquid water proofing compound will be measured and paid for separately as "supply only" against relevant item of BoQ)

M&L for 5mm thick rendering in CM 1:3 as on ceiling, soffit of RCC shelves, surfaces finished even and smooth without using extra cement complete all as specified & directed.

M&L PCC ( 1:4:8 ) type D-2 (using 40 mm graded stone aggregate ) as in foundation filling and mass concrete complete all as specified and as directed.

M & L for water proofing treatment for sunken slab with polymeric standard water proofing membrane, Aquaflex having 10 years gurantee for water tightness complete all as specified and described as under:- (a) Preparation of sunken surface by providing 10 mm thick rendering in cement mortar (1:4) mixed with liquid WPC as per Manufacturer's instructions and applying one coat of polymeric modified bitumen 85/25 @ 1.2Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/sqm including cleaning surface all as per manufaturer's specification complete all as specified and directed. (b) Supply & providing water proofing with polymeric proofing membrane of 3Kg/Sqm consisting of 100micron HMHDPE film centre core including coating the surface with compatible primer and torch application of membrane with 10cm overlaps as required thereof, complete all as specified and directed (c) GI pipe 40mm bore light grade shall be embedded as outlet at the lowest portion of slope, in the wall extending upto at least 450 mm beyond the outer wall

M&L for applying oil based bitumen primer @ 0.30 kg/Sqm and laying 3 mm thick APP modified water proofing membrane weighing not less than 3.00 kg/sqm, reinforced with non woven polyester reinforcement matt weighing not less than 160 gm/Sqm polyester core, torch application, with a min overlap of 100mm at the sides and 150mm at the ends, sealing and applying two coat of bitumen based aluminium paint @ 0.20 Kg/Sqm on membrane surfaces complete all as specified and as directed .

S & F for CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors including chase cutting and fixing with solvant suitable for CPVC pipe and brass treaded fittings for fixing taps and valves, complete all as specified and directed.

S&F for CPVC pipes 25 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors including chase cutting and fixing with solvant suitable for CPVC pipe and brass treaded fittings for fixing taps and valves, complete all as specified and directed.

M&L for PCC (1:2:4 ) type B1 (using 20mm graded stone aggregate)as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs,Hold fast and similar works water troughs and the like including weathering, slightly rounded for chamfered angles and necessary formwork complete all as specified and as directed

S & F Pressed steel frames made of 1.25 mm thick MS Sheet size 125x60mm for doors, with double rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified & directed by Engr-in-Charge.

S & F Pressed steel frames made of 1.25 mm thick MS Sheet size 105x60mm for doors, with single rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified & directed by Engr-in-Charge.

M & L for providing PCC (1:2:4 ) type B0 (using 12.5mm graded stone aggregate ) to fill the frame & making good the disturbed surface complete all as specified & directed by Engr-in-Charge.

S&F 35 mm factory made shutters of second class hard wood Plain framed, panelled shutter (three panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated supplied and fitted to chowkat complete all as specified and directed

M&L for 35 mm thick 2nd class hard wood glazed/gaused and skelton door shutter, factory made, open rebated and prepared to receive glass/guage etc. (without sash bar) edge of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guage etc size of member as specified in SSR Part I Section 8 clause 8.24(a) and fixed to chowkat, complete all as specified.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels with sunmica on both sides both face is covered with lipping/frame to match as in cupboard door shutters complete all as specified and directed

S & F Factory made internal PVC door frame of size 100 x 60 mm single revated made out of solid PVC mitred cut at two corners and jointed with 02 Nos of 150 mm brackets of 15x15 mm MS square tube. The two vertical door profiles are to be in forced with 40x20 mm MS tube of 19 gauge through out the frame complete all as specified and as directed by Engineer-in-Charge.

S & F Providing and fixing 30mm thick FACTORY MADE MOULDED DOOR SHUTTER ‐ WOOD FREE consisting of frame made out of M.S. tubes of 19gauge thickness and size of 25mm x 25mm for stiles, top and bottom rails. M. S. frame shall have a coat of steel primers. The inner panel shall consist of 25mm thick EPS of Density 23 Kg /cum. bonded with 2mm thick termite proof, water proof and fire resistant moulded PVC Sheet Manufactured by an ISO‐9001‐2015 certified company, with 2, 4, 6 raised panel design in different plain and / or prelam colours after routing the Moulded design on one side & 2mm plain and /or prelam PVC sheet on other side of the EPS. The edge of panel to be sealed with lipping of 15mm wide PVC sheet baton ( made by sticking 2mm rigid foam PVC sheets of 5mm (±0.25) thickness using PVC solvent cement ) and stile sides 25mm (5mm x 5nos.) thick and 30mm width PVC Sheet fitted along M.S. tube for hardware provision & for lock 25mm thick ( 5mmx5nos. ) PVC sheet of size 150mm x 200mm fixed with inner side of EPS Panel etc. complete all as per specification & drawing and as directed by Engineer-in-charge.

S&F aluminium powder coated(minimum thickness of powder coating 50 micron) window sliding type (3 track) with frame size 100x35x1.2mm thick and shutter frame size 39.40x17.70x1.2mm thick with two glass shutter and one mesh shutter including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with and including 4mm thick plain float glass and 0.36mm dia apperture 1.4mm stainless steel wire mesh and fittings etc and making good the jambs and painting to match with existing surface complete all as specified and directed .

S&F aluminium powder coated(minimum thickness of powder coating 50 micron) louvered ventilators of section size 80mmx20mmx1.50mm including 5mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc. making good the jambs and painting to match with existing surface complete all as specified and directed.

M & L for timber, 2nd class HW, plain fillets, square, rectangular or triangular in section, wrought, fixed with screws, sectional area exc 13cm but n. exc 25sqcm.with white sunmica, Including dismantling existing,unframed work, complete all as specified and directed.( 169.73+15.30)

S&F, in repairs, 18mm thick ply, PVC sheet with prelaminated on one side of approved texture (as approved by GE) as in Kitchen cabinet and cupboard etc (with shelves and partitions) including necessary fittings & fixtures as per manufacturer's instructions complete all as specified and directed.

S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

S&F 100mm long Butt hinges,medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

M&L for 200mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

M&L for 150 mm long aluminium anodised handles, oval type, stove enamelled black complete all as specified and directed.

S&F 75mm long Butt hinges,medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

M&L for 150 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

M&L for 125 mm long aluminium anodised handles, oval type, stove enamelled black complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 35 mm complete all as specified and directed.

S&F in repair 50 mm size magnet catcher, cupboard lock, safety type, Aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repairs 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor

M&L for Machine cut cudappah stone slab 20-25mm thick as in Shelf/cooking platforms, and like including cutting and fixing over and including 15mm thick cement screed base in CM (1:4) and jointed to support granite top complete all as specified and directed.

M & L Granite (Black/Ruby Red ) work (table rubbed and polished) 18 to 20 mm thick in cooking platforms bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including grinding and polishing complete over and including screed bed 15 mm thick in CM 1 : 6 complete all as specified and directed.

M&L for Granite tiles 18 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with the shade of granite stone laid over and including 15 mm thick screed bed of CM (1:4) , as in tread and riser of staircase,steps , jambs, pillars, window- cills, complete complete as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

M&L for mild steel work conforming to Fe-290 Gde E-165 as in hand rail, holdfast, half round or other steel section or core for wooden hand rail strait portion, drilled and countersunk for balusters running bars for doors, nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in leveling course complete all as specified and as directed.

M & L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles, laid over and including 20 mm thick Cement mortar (1:4) screed bed, complete all as specified.

M & L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished,not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles, laid over and including 10 mm thick Cement mortar (1:4), complete all as specified and directed.

S & F Non - skid Ceramic colour tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:4 all as specified.

M&L Glazed ceramic colour tiles in vertifical surface 450x300x7mm thick with necessary border etc., set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles, laid over and including 10mm thick renderting/ back coating in cement mortar 1:4 complete all as specified and directed

S & F Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars and similar work conforming to Fe- 290 ( Gde-E-165) complete all as specified and as directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts). No claim whatso ever shall be entertained by Govt on this account.

S&F framed work as in iron enclosure, doors or gate of angle iron or other section with gussets plate, rails, braces etc drilled for fixing of steel seating other covering, door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel handing door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and as directed. Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account.

S&F in repair 1 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required, complete all as specified and directed.

S&F in repair mild steel, Framed work as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde E- 250 quality-A) complete all as specified and directed.

M&L, in repair, for mild steel work conforming to Fe-290 Gde -165 as in nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.

Supply and fix, in repair, pre-painted galvalume aluminium zinc coating GI based 0.50mm thick(AZ-150)corrugated steel sheet of any colour having minimum tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws/ L or J type or cranked hook/ bolts as complete all as specified & directed.

M&L 75 mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate laid in panels surface finish even and smooth without using extra cement as in plinth protection, hard standing and similar works, complete all as specified and as directed.

M & L for 100mm thick PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in subbase, Hard standing and similar works, complete all as specified and as directed.

M&L for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed.

Labour only for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed. ( Note : Old serviceable bricks retrieved against dismantling shall be re-used)

Disconnecting existing tanks,Capacity exc 500 ltrs but n exc 1000 ltrs setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

Supply and fix 500 ltrs capacity rotational moulded polyethylene water storage tank double layered, ISI Marked, (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

Supply and fix 1000 ltrs capacity rotational moulded polyethylene water storage tank double layered, ISI Marked, (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

S&F, in repair, 25 mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description over 10 cm in width or girth not otherwise described and applying one coats of synthetic enamel paint complete all as specified and directed.

M & L for preparing new or previously untreated wood surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified

M&L preparing old wood or wood based surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.

M & L preparation of New plastered wall surfaces and applying 2mm thick wall care putty in two layers, to get smooth and even surfaces as directed and applying two coats of oil bound distemper over resistant priming paint complete all as specified and as directed .

M & L for complete removal of existing treament and preparation of old plastered wall surfaces and applying 2mm thick wall care putty in two layers, to get smooth and even surfaces as directed and applying two coats of oil bound distemper complete all as specified and as directed .

M & L for preparation of new plastered ceiling surfaces and applying 2mm thick wall care putty in two layers, to get smooth and even surfaces as directed and applying two coats of oil bound distemper over resistant priming paint complete all as specified and as directed .

M & L for complete removal of existing treament and preparation of old plastered ceiling surfaces and applying 2mm thick wall care putty in two layers, to get smooth and even surfaces as directed and applying two coats of oil bound distemper complete all as specified and as directed.

M&L for Preparation of new/old wall surface or complete removal of existing treatment on wall surfaces of any description including brooming down with steel wire brushing, scrapping down smoke soots , moulds, moss and efflorescence, salts, trading oil and greasy spots etc and applying two coats of Anti fungal weather proof grade exterior acrylic emulsion paint of approved tint over a coat of weather proof primer including filling the cracks etc with crack filling upto 5 bars of positive hydrostatic pressure on vertical walls without any dilution with forced coverage not more than 3.5 Sqm / Ltr as per manufacture's instruction and all coats incl primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSIAllow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and directed

S&F in repair vitreous china wash basin white flat back size 550x400 mm including,pillar tap, 32 mm dia CP waste fitting and PVC waste pipe 610 mm long and brackets, complete all as specified and as directed.

Supply & fix, in repair, vitreous china squatting pan, Orissa pattern of size 580x440 mm white, with integral foot rest and PVC 'P' or 'S' trap including connection to trap, and to flush pipe, etc (excluding flushing pipe) and making good to floor complete all as specified & directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including all necessary fittings complete all as specified and directed.

S & F in repairs PVC Low level flushing cistern 10 litres capacity including all fittings I.e float valve, syphon, flushpipe,brackets complete all as specified and directed.

S&F, in repair kitchen sink with drainage board made out of 1mm thick stainless steel with plugs, washers & wastes including CI cantilever bracket & connection union to pipe over all size 915mmx460mm & bowl size 410 x330x160mm complete all as specified and as directed.

S&F in repairs Stop cock (Concealed) cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule with long shank and cup for 20 mm bpre of pipe complete all as specified and as directed.

S&F in repair angle cock cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule for 20 mm bore of pipe complete all as specified and as directed.

S & F in repairs CP shower rose 150 mm round with arm and flange including fixing to steel pipe complete all as specified and as directed

S & F in repair PVC connections 15mm dia with PTMT nut on both ends and washers 450mm long complete all as specified and directed.

S&F in repair Bib tap long body cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed for iron pipe or or brass ferrule for 15 mm bore of pipe complete all as specified and as directed.

S&F in repair,15 mm dia WHB Mixer , cast copper alloy, fancy type,chromium plated,screwed down high pressure,with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed.

Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match with the existing floors complete all as specified and as directed.

S&F in repair 0.63 mm thick kitchen plate rack made of stainless steel 600 x 750 x 220 mm size fixing with wooden plug with suitable size of screws complete all as specified.

S&F stainless steel kitchen basket in various type of basket such as plain basket , Thali basket, Cup and saucer and perforated cutlary basket, made of SS-304 anti-corrosive material complete all as specified and directed.

S&F hettich channel for basket size 46 mm wide complete all as specified and directed.

S&F for 32 mm dia PVC waste pipe suitable for WHB / Kitchen sink complete all as specified and as directed.

S&F in repair brass CP fancy type sink mixer with hot & cold knob and fixed complete all as specified and as directed.

S&F in repair PVC (SWR) gully trap 150 x 150 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F in repair PVC floor trap square type with CP grating with or without hole including provision of jointing to waste pipes in run lead joint, dia of outlet 75 mm, complete all as specified and directed.

S&F in repair towel rail 450 mm long of Brass CP fixed with and including chromium plated brass screw and wooden / plastics cleats complete all as specified and as directed. ( min wt 170 gms)

S & F in repair of 110 mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches,floor and wall including taking down old unserviceable pipe any description and any type complete all as specified.

S & F in repairs PVC (SWR) Pipes single socketed in any length with rubberring joints laid in trenches or in floors and wall 75mm bore including taking down old unserviceable pipe any description and any type complete all as specified and as directed.

S & F in repairs PVC (SWR) bends 110 mm dia bore any radius with access door complete all as specified and as directed.

S & F in repairs PVC (SWR) bends 75mm dia bore any radius with access door complete all as specified and as directed.

S & F in repairs PVC (SWR) branch piece, single (single Y) 110 mm dia equal or unequal

S & F in repairs PVC (SWR) branch piece, single (single Y) 75mm dia equal or unequal

S&F in repairs 75mm bore PVC (SWR) junction single (Single T) equal or unequal.

S&F in repairs 110mm bore PVC (SWR) junction single (Single T) equal or unequal.

S&F in repairs 110mm bore PVC (SWR) vent cowl complete all as specified and as directed. .

S&F, in repair, Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed.

S&F in repairs 25 mm dia Stainless Steel drapery rod / curtain rod with bracket and fancy knob etc fixed with rawl plug and CP screw complete all as specified and directed.

M&L for Water Poofing Treatment of external walls , chajja and newly plastered surface by applying two coats of elastomeric coating material after cleaning the surface thoroughly and sealing all cracks with acrylic sealing compound complete as per the manufacturer instructions complete all as specified and as directed.

S&F in repair plastic water closet seat, white/black closet pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Supply and fix in repairs elegant mirror PVC Cabinet of size (475x600x150mm) complete all as specified and directed.

S&F corner glass shelves 300 mm with railing fixed with C-bracket consisting of 5.5mm thick sheet glass shelf with chromium plated bracket guard complete all as specified and directed .

S & F CP jet spray fitting to EWC or wall with screws and including two way CP stop cock 15mm dia complete all as specified and directed .

S&F in repair health Faucet ABS body ,with 1 metre Stainless Steel Braided connection pipe complete all as specified and directed.

S&F, in repair, wall mixer, three in one, with complete accessories complete all as specified and directed .

S&F, in repair, Toilet paper holder, fixed to walls with chromium plated (CP) brass screws complete all as specified and directed .

S&F, in repair, towel ring of CP, fixed with and including CP brass screws and wooden / plastic cleats (min wt 90 gms) for kitchen complete all as specified and directed .

Supply only liquid water proofing compound ISI Marked, of make as approved by GE complete all as specified & directed.

Demolition of reinforced cement concrete as in Roofs, floors (other than groundnfloors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping),flat, fair finished surface of concrete, complete all as specified and directed.

Reinforced cement concrete (1:2:4) Type B-0 (12.5mm graded crushed stone aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves,Chajja and the like, complete all as specified and directed .

M&L for mild steel TMT bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 8 mm dia as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete including removal of debris to out side MD land complete all as specified & directed.

Resecuring without taking down chowkats or frame with shutters of any description (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

Dismantling of timber scantlings unframed 40Sq Cm and over in section, in any position complete all as specified and directed.

Dismantling wall and ceiling boards any type (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Taking down steel tubing and connections including cleaning for refixing or removal from site for 15mm bore pipe all as specified and directed by Engr-in-charge.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortar for 150 mm internal dia of pipe complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section,in concrete, brick work masonary including taking out embedded portion and making good disturbed ground.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, head, shoes, bends, swan-necks atc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified & directed

M & L for dark shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match,over 20 mm thick Cement mortar (1:4) screed bed, complete all as specified.

M & L for dark shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished,exceeding 0.36 sqm but not exceeding 0.42 sqm, in skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles, laid over and including 10 mm thick Cement mortar (1:4), complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring, 20-25 mm thick over & including 15mm thick cement screed bed in CM (1:6) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for Machine pressed precast cement concrete rubber moulded interlocking paver block any shape and size conforming to IS 15658-2006 of 80mm thickness, M-40 Grade, laid over and including 50mm thick sand cushioning complete all as specified and directed.

M&L 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded crushed stone aggregate as in floors including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed.

M&L for PCC (1:2:4) type B1 using 20 mm graded stone aggregate for insertion of hold fast including necessary form work etc complete all as specified and directed.

Plain Cement concrete (1:2:4) type B-1,using 20 mm graded stone aggregate as in flooring 100 mm thick and finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed .

M&L 100 mm thick PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in floor sub base and finished even and fair complete all as specified and directed.

M&L for chequered Rubber moulded cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and no pigment in floors over and including 15 mm thick screed bed in CM (1:6) for laying floor finish complete all as specified and all as direcred.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 in half brick thick wall complete all as specified and directed.

Cutting holes in brick walls exc 1/2 brick & n exc full brick built in cement mortar for inserting hold fasts, cutting and preparation of brick wall for insertion of doors, windows & ventilator and making good dismantled portion in cement mortar 1:3 etc complete all as specified and directed.

S&F 35 mm factory made shutters of second class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated supplied and fitted to chowkat complete all as specified and directed

S&F PVC moulded door frame of size 50mm x 95mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube supplying & fixing in opening but single pre laminated PVC sheet used instead of plain colour PVC sheet as per specifications complete all as specified and as directed.

S & F 35 mm thick 2nd class hardwood moulded glazed/gauged door with pre pressed lamination on both side, solid core construction & prepaid to receive glass/wire mesh including fixing of SS wiremesh of nominal dia 0.36 mm , 2 Nos door handle, 3 Nos SS butt hing of 100mm , 2 nos Aluminium tower bolt 150mm length in each shutter complete all as specified in SSR Part I and as directed and fitted to chowkhats.

S & F 30 mm thick 2nd class hardwood moulded flush door with pre pressed lamination on both side, solid core construction 2 Nos door handle, 0.3 Nos butt hing of 100mm , 2 nos tower bolt 150mm length and 300 mm length sliding door bolt in each shutter complete all as specified in SSR Part I and as directed and fitted to chowkhats.

M&L for IInd class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified & directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 40mm complete all as specified and directed.

M&L for box type or other type section for door frame for fixing of door shutter of single MS channel etc complete as specified and directed.

M & L Aluminium powder coated( minimum thickness of powder coating 50 micron) sliding windows(three track) of frame of size bottom section 92.00x31.75x1.50mm ( Section No 20832),Top and Sides of size ( Section No 20831) with anodised aluminium shutters Top and bottom size 40x18x1.55mm (section 20736) and sides ( handle) of size 40x18x1.55mm (section 20738) and lock side shutter frame size 40x18x1.45mm (section 20737) including rubber gasket,beading and locking arrangement , both glazed and gauzed with 5.0 mm thick glass, stainless steel wire cloth netting(0.36mm nominal dia and averege width of aperture 1.40mm), and fixed including necessary glazing clips, rubber packing, anodized aluminiunm snap beading screws and aluminium fittings of standred size complete all as specified and directed. ( Notes : (i) Glazing and stainless steel wire cloth will not be measured and paid for separately under relevant items of this BOQ

S & F anodised aluminium powder coated (minimum thickness of powder coating 50 micron) Ventilator louvers type frame top and sides of size 31x42x1.6 mm ( Section No 20558) rectangular tube of size 40x20x2.0mm ( Section No 14019) and middle vertical of size 42x46.20x1.60mm ( section No 20560) and clip for fixing in wiremesh and glass of size 19x17.30x0.90mm ( section No 19360) including rubber gasket, beading, anodised aluminium snap beading, screws, handle,fixing 4.00 mm thick glass frosted glass , 0.36 mm nominal dia wiremesh with necessary rubber beading gasket etc including necessary plaster, painting ,cill and making good to disturbed portion all as specified and directed. ( Notes : (i) Glazing and stainless steel wire cloth will not be measured and paid for separately under relevant items of this BOQ

S & F Factory made internal PVC door frame of size 50x47mm single revated made out of extruded 5 mm PVC foam sheet, mitre cut at two corners and jointed with 02 Nos of 150 mm brackets of 15x15 mm MS square tube. The two vertical door profiles are to be in forced with 40x20 mm MS tube of 19 gauge through out the frame complete all as specified and as directed by Engineer-in-Charge.

S&F for aluminium anodised, barrel tower bolts of extruded section with length of bolt 100 mm and fixed complete all as specified and directed.

S&F for extruded aluminium alloy handles, fabricated type, anodised of size 100 mm complete all as specified and directed.

S&F for extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

S&F, Mild steel sliding door bolts 300mm size, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F mild steel, 300 mm long ordinary helical door spring including roller and roller plate complete all as specified and directed.

S&F Floor 40-50 mm door stopper of aluminium alloy body and tongue anodised with hard steel spring ,fixed in floor complete

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified and directed.

S& F 3 mm thick sheet glass ordinary quality and glazing with oil putty/wooden beading in square n. exc 0.5 Sqm in each pane complete all as specified and directed.

S & F 3 mm thick figured glass pin head type and glazing with oil putty/wooden beads in squares n exc 0.5 Sqm in each pane etc complete all as specified and directed.

S&F in repairs Stainless steel fancy type curain rod 25 mm including SS brackets, decorative knobs,and including all necessary fittings such as rawl plug screws complete all as specified and directed.

S & F 2nd class hardwood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed.

S&F 25mm bore tubes medium grade galvanized with all fitting such as socket, elbow, Tee tee, union and short length etc. and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed by Engr-in-charge.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for 16mm bore of pipe including Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor and all necessary fittings etc complete all as specified and directed.

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S & F in repair 15 mm bore brass chromium plated Wall Mixer three in one including Provn of OH shower and including hand shower fancy type screwed down to GI pipe with CP brass cup complete all as specified and directed.

S&F vitreous china wash basin white flat back, size 550 x 400mm excluding taps, waste, chain & plug and porcelain stopper but including brackets, PVC connections 450 mm long complete all as specified and directed.

S&F in repair PVC low level flushing cistern of capacity 10 litres complete with siphon handle, lever, float valve and PVC bend including connecting to ITWC/ ETWC, PVC connection 450 mm long and fixing on wall bracket complete all as specified and directed .

S&F in repair PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and as directed.

S&F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete all as specified and directed.

S&F in repair 15mm bore stop valve/ angle valve fancy type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for union all as specified and directed by Engr-in-charge.

S&F in repair of CP Soap dish, any type, fixed to plugs with chromium plated brass screws.

S&F in repair 0.63 mm thick kitchen plate rack made of stainless steel 900 x 750 x 220 mm size fixing with wooden plug with suitable size of screws complete all as specified.

S&F in repair chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed

S&F stainless steel hinges 100 mm for cupboards of senso (as per 3D designs) inclduding all connection fitting as complete all as specified and directed and approved by GE.

S&F Handles of senso (as per 3D designs) 150 mm inclduding all connection fitting as complete all as specified and directed and approved by GE.

S&F PVC (SWR) nahani/ floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia etc complete all as specified and directed.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over new surfaces of plaster / stone complete all as specified and directed.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over and including prepration of old surfaces of plaster / stone complete all as specified and directed.

Prepration of newly plastered surfaces and applying three coat of white wash on ceiling all as specified.

M&L for laying DWCP 150 mm dia pipes in trenches Class SN-8 conforming to IS 16098 (Part -2) in 6 mtr length with coupler complete all as specified and directed by Engr-in-charge.

S & F Door Seal rubber etc, complete all as specified

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding/ ridge to wall, fixed with self tapping screws complete all as specified and directed.

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, wind ties etc. conforming Fe 410 -W (GdeE- 250) qualityA complete all as specified and directed.

Providing and filling epoxy putty into RCC crack after opening up RCC cracks in V– groove manner approximate 10 mm wide & 10mm deep using mechanical cutter, properly cleaning the same to remove loose dust dirt etc and filling the same using Nitocote VF –three component, solvent free, thixotropic, Epoxy resin based putty having 100% solid contents mixed density of 1.6 g/cc, compressive strength – 50 N/mm ², pot life of 40 minutes at 27 degree C, Drying time 8 hrs. recoatable time 24 hrs. and finishing in line and level with existing concrete surface etc. complete all as specified and directed. Notes : (i) Quoted rate shall be deemed to be inclusive of materials, labours, tools and plants, scaffolding and working upto height 6 mtr etc. complete as per specification and directed by GE . (ii) Adoption of necessary safety arrangements like safety belts ropes, helmets netting etc which are required for safety of worker working at height exceeding 3 mtr shall be mandatary and deemed to be inclusive in quoted rates

M & L for snap grid false ceiling system of E board exposed suspended system, grid size 600mm x 600mm compressing of GI powder coated Main Runner of dimensions 39mm x 24mm x 0.8 mm thick to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt-0.007 kg/clip), hold down clips (wt-0.0035 kg/clip), and fixed with pre painted 4mm thick E board of approved design and with provn of light fixture complete all as per manufacturer instructions and as directed.

M&L MS work as in wind ties for roof including securing bolts, drilling holes, notching for wire etc complete all as directed.

S&F, in repair, chromium plated, Toilet paper holder complete all as specified and directed.

S & F in repair 32 mm thick PVC waste pipe of minimum length 1 mtr for kitchen sink and WHB etc complete all as specified and directed.

S & F in repair 40 mm thick PVC waste pipe of minimum length 1 mtr for kitchen sink and WHB etc complete all as specified and directed.

Supply & Fixed in repairs Two way angle cock complete as specified and as directed.

Supply & Fixed in repairs Corner Glass Shelves including C type bracket fixed with steel screws complete all as specified and directed.

S & F in repair 15 mm bore brass chromium plated Sink Mixer for hot & cold water with long shank and fly nut complete all as specified and directed.

Taking down carefully any type point wiring (light, fan, socket bell or power) , complete with fitting such as switches ceiling roses,lamp holders sockets,regulators,call bell light fitting with PVC conduit surface /concealed or wooden pattens including sunken cast iron /pressed steel terminal boxes etc complete all as specified and directed by Engineer in charge.

Taking down carefully Main switch and Distribution boards any make and size .

Taking down the ceiling fan/exhaust fan in situ and depositing it in MES store complete all as specified and directed.

Taking down carefully Old unserviceable any type sub main wiring with wooden batten/PVC surface conduit of any size and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed by Engineer in charge.

M/L for Sub Main Wiring two single core PVC insulated cable of size 6.0 Sqmm multistranded copper conductor two run drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting,fixing accessories and one run of 6.0 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :-Two Nos of 6.0 Sqmm Wire and one No of 6.0 Sqmm Earth wire in One RM length Measured as one unit length.

M/L for Sub Main Wiring with two single core PVC insulated cable of size 4.0 Sqmm multistranded copper conductor drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 20mm dia with all conduit fitting,fixing accessories and 4.00 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :- Two Nos of 4.00 Sqmm Wire and One No of 4.00 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of antirorrrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engineer in charge.

One light point/Bell point controlled by one switch 5/6 Amp.

One fan point controlled by one switch 5/6 Amp.

One socket point controlled by one switch on same board.

One socket point controlled by one switch on Independent board.

Description all as per item No 213.00 here-in-before but with 1100 volts grade copper standard conductor cable of size 2.5 Sqmm with 2.5 Sqmm stranded copper conductor for 3 pin switch socket outlet15 Amp independent board complete all as specified and directed by Engineer in charge .

S & F in repair for bell ding dong AC 230 volts single pole one way complete all as specified and directed by Engineer in charge.

S & F in repair for Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

S & F in repair for Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed by Engineer in charge

S & F in repair for switch socket combination 3 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and directed by Engineer in charge

S & F in repair for Ceiling rose surface bakelite 65 mm x50 mm three terminal AC 230 volts flush type complete all as specified and directed by Engineer in charge

S & F in repair fan regulator Step type of polycarbonate complete all as specified and directed by Engineer in charge.

Supply and fixing in repair of LED lamp rotary type/holder type of 9 watt all as specified and directed.

Supply and fixing in replacement of decorative wall light fitting WITH LAMPS 12 WATT made up of Polycarbonate , City-1 , Cylindrical shape , with LED lamp 9 Watt complete with fixing arrangements on wall all as specified and directed.

Supply & Fixing Smart bright Batten Series, LED luminaire using LED 22 watt 110 Lumens/watt with diffuser which ensures uniform distribution and comfort, batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminium housing, Energy efficient, Flicker free start Inbuilt driver unit, Suitable for wall and ceiling mounting using brackets with and including the luminaire testing on completion as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), complete all as specified and directed.

S & F in repair of LED Decorative /mirror light fitting 10watt along with fixture Surface mounted suitable for indoor aplication , connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge.

S&F in repair Bulk head endura LED light fitting complete with10 watt LED and making necessary electric connection to ceiling rose with copper conductor of suitable size & length complete all as specified & directed.

Supply & fix in replacement of LED Security Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with two coats of aluminium paint over a coat of primer. complete all as specified and as directed.

S & F in repair Sheet metal enclosure DBs Tripple Pole and Neutral 4- way with 200 Amps rated bus bar 415 volts single pole and neutral complete double door complete all as specified and directed by Engineer in charge

S & F in repair MCB TPN 415 volts 63 Amps, C Series complete all as specified and directed by Engineer in charge .

Supply and fixing Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet remote control radio frequency 5 speed +off timer option speed regulation class of insulation two nos bearings including connecting wire complete with all as required and directed.

S & F in repair Sheet metal enclosure DBs Single Pole and Neutral 8 way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and directed by Engineer in charge

Supply and fixing in replacement MCB single pole and neutral 240 volts 40 Amps, B Series complete all as specified and directed by Engineer in charge

Supply and fixing in replacement MCB/Isolators single pole 240 volts upto 40 Amps, B Series complete all as specified and directed by Engineer in charge

Supply & Fixing in repair modular AC box (earth plug socket) complete with 01 number single pole MCB 20 Amps complete all as specified & directed.

S & F in repair for bell push piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep, metallic body complete with Metalic louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep, made of sturdy Engineering plastic complete with louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with PVC flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.

Supply and fix Geyser 25 ltr with fitting arrangements all as per required and directed

Supply and install electric chimney max 1000cum all as per reuqired and directed by Engg In Charge.

M&L for earthing complete with galvansided steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to galvanised iron wire 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 15mm bore GI pipe medium grade including necessary fittings for protection of earthing wire, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear including 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith protection pipe and testing on completion complete all as specified and directed. Note:- GI wire and protection pipe from earth electrode to test point max upto 7.50M shall be deemed to be included in the unit rates as quoted by the contractor.

Supply, installation, commissioning and testing indoor wall mounting LT Panel Board of minimum size 1.20 m (height) x 1.20 m (breadth) x 0.30m (depth) factory made CPRI approved panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of Seven nos single phase meter and MCB and providing glass view for reading of meter and providing rubber/ PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/ sleeves with the colour code and copper strip/wire busbar of suitable size to MCCB input and MCCB/MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 1.5 sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as directed by Engineer-in-Charge. (For JCO/ORs, Civilian Md Accn 06 Qtrs)

OUTGOING :- (a) MCB, Single pole & neutral, 40 amps, 240 volts, 'C' curve, 10 KA -06 Nos (b) MCB, Single pole & neutral, 10 amps, 240 volts, 'C' curve, 10 KA - 1 No.(stair case lighting) (c) Fixing only serviceable existing electric meter - 01 No. (d) Smart Single Phase Meter AC single phase Four wire, tamper proof, static meter of class 1.0, 240Volts, 50 Hz of capacity 10 Amps-60 Amps conforming to IS-16444 and relevant IEC standards with in built 865-867 MHz radio frequency communication facility with self healing mesh network with default and on demand display, billing data generation facility, anti-temper features, microprocessor and LED/LCD based circuitry. Meter should support the follwing data: 30 min instantanous data for voltage, current, power factor, power cumulative energy and frequency, 30 load survey data for energy, monthly billing survey for cumulative energy and max demand. Meter should have connnect/disconnect funtionality operable compactable system from prepaid billing software in future. The meter should support open communication protocol DLMS with the software. 05 Nos.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 25 sqmm, 4 core including jointing materials such as cable glands & lugs etc complete all as specified and directed.

Supply,laying & fixing Double Wall Corrugated (DWC) pipes made of High Density Polyethylene (HDPE) with all accessories i.e. all type of joints,Sockets,Elbows,bends and End caps etc.. complete all as specified and as directed , outer dia 50 mm and inner dia 38 mm complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply and fix Geyser 25 ltr with fitting arrangements complete all as per required and directed. Note :- Old Unserviceable geyser shall be deposited to MES store

Schedule of credit amount of Rs 1,05,995.00 to be deducted during AOC

RAVI ENTERPRISES (BID ID -3091709)

Kirti Chandeliya and Assosicates (BID ID -3096888)

Tiki Water proofing Co (BID ID -3081188)

M/s Ram Associates (BID ID -3091892)

DEEPAK CONSTRUCTION (BID ID -3096990)