REPAIR TO SEEPAGE/LEAKAGE OF UG SUMP, ROOF, PLASTERING, FLOORING, JOINERY, PERIODICAL SERVICES TO MES INSTALLATION AT HASTINGS, BMC, OD SAHAPORE AND RASPUNJA UNDER GE (C) KOLKATA

Amount

Demolition existing Roof Padding including Roof Treatment complete carefully by cutting, chiseling, etc. and cleaning the surfaces by scrapping, booming, bruhing, etc. and removing the rubbish from Site to a distance n exc 50.00 Metre complete all as specified and as directed.

Demolition of cement concrete (Un-reinforced) in ground floor and paving nexc 15cm thick above or below GL complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed.

Dismantling AC Corrugated Sheets as in Roofing including Ridge or Similar Pattern Roof Coverings, complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work, viz. MS Flat Iron (Wind Tie) and Similar Work including MS Bolts, Nuts, etc., complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from frames) of any sizes n exc 1.5 Sqm each complete all as specified and directed.

Taking down Chowkat or Frame with shutters (without taking off Shutter from the Frame) exc. 1.50 Sqm but not exc. 4.00 Sqm Each, complete all as specified and as directed.

Taking down Shutters of any description, not exc 1.00 Sqm Each, and keep in Safe Custody for removing to store, complete all as specified and as directed.

Taking down Shutters of any description, exc. 1.00 Sqm but not exc 2.00 Sqm Each and keep in Safe Custody for removing to store, complete all as specified and as directed.

Taking down Rolling Shutters of any description, nexc. 7.00 Sqm Each and keep in Safe Custody complete all as specified and as directed.

Taking down Rolling Shutters of any description, exc. 7.00 Sqm but not exc 12 Sqm Each and keep in Safe Custody complete all as specified and as directed.

Taking down Rolling Shutters of any description, exc. 12.00 Sqm Each and keep in Safe Custody complete all as specified and as directed.

Dismantling fencing wire mesh, any type complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

Dismantling of stone slabs and tiles laid,bedded and pointed in any mortar of any description or thickness in floors, aprons etc all as directed by Engineer-in-charge.

Dismantling floors hearth or wall tilling including cement mortor bedding (but not backing) removing serviceble tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement plaster of any description on brick work or stone msonary wall including racking ot joints hacking for key scrubbing down with water etc. complete all as specified and directed.

Hacking Out Old Broken Glass (any thickness, size, quality or description) from Wooden Frames, Glazed with Putty or fixed with Beads, complete all as specified and as directed.

Taking up or down Steel Water Tubing 15mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use, or removing to store, complete all as specified and as directed.

Taking up or down Steel Water Tubing 20mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use or removing to store, complete all as specified and as directed.

Taking down unserviceable PVC (SWR) Pipes & Fittings of any size or pattern and in any Position (Measured overall as fixed along the Centre Line over the Fittings and Accessories), complete all as specified and as directed.

M&L RCC (Nominal Mix) 1:2:4 type B-1 (Using 20mm graded stone aggreagate) as in slab, shelves supported on walls beam & coloumns in floor roof including balconies, conopies, deck slabs & shelves complete all as specified and directed.

M&L Plain cement concrete 1:2:4 type B1 (using 20 mm graded crushed stone aggregates) as in bed block for embedding angle iron fencing post. complete all as specified and as directed.

M&L Cement Concrete Type B0 (1:2:4) (12.5mm graded crushed stone aggregate) as in padding and benching and filleting ,roof kerbs or mud stop complete all as specified and directed.

M&L Plain Cement Concrete type C-1, (1:3:6) (40mm graded crushed stone aggregate) as in Coping. bed plate,hold fast etc,block benching,channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed.

Cutting chases, pinning in making good to facing where required and pointing in CM 1:3 to end or edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chase for concealed water pipe etc. and making good cutting not exc 10Cm girth complete all as specified and directed.

Carefully chipping of damaged, detoriorated, spalled, debinded and weak concrete from the beams columns walls, roof of staging structure at all height including removal of rubbish upto a lead of 50 metre complete all as per direction of Engineer-in-Charge.

Removing rust from existing corroded reinforcement by mean of application of Rust Remover such as Hind Rust Clean (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc and then washing the same to make the reinforcement scale free complete all as per the direction of Engineer-in-Charge. Note : Payment to be made on exposed RCC area

M&L for Application of anticorrosive paint such as Hind Anti Rust (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc on cleaned reinforcement as per manufacturer's specification complete including labour and material complete all as per direction of Engineer-in-Charge. Note : Payment to be made on 25% of exposed area

M&L for Application of bonding coat based on polymer modified cementious material such as Nitobond SBR/Hind Styrene BR (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc @ 0.50 Kg/Sqm (due to rough concrete surfaces) to act as bonding agent between old and new concrete including material and labour as per manufacturer's specification and complete all as per direction of Engineer-in-Charge.

M&L for pressure guniting at a pressure not less that 6Kg/Sqcm to surface of column, beam, ceiling, facia and similiar structural members in polymer modified concrete with mix ratio 1:1.5:3 (1 cement : 1.5 Coarse Sand : 3 Stone aggregate of 10mm nominal size) admixed with acrylic latex polymer such as Hind Styrene BR/Nitobond SBR (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc @ 3.00 Kg per Sqm and plasticiser Hind Plast Super/Conplast SP 337 (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc @ 100Gms per Sqm for an average thickness of 50mm (the concrete to be applied when the bonding coat is still green) including material and labour, scaffolding and formwork etc. complete all as per manufacturer's specification and direction of Engineer-in-Charge

M&L Application of two coat of acrylic polymer slurry coating on 10 x 10 count glass fibre wooven mesh over the cured plastered inside surfaces of tank with Hind Crete Plus WPM (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc after proper cleaning by brushing washing etc to act as waterproofing membrane complete all as specified and directed.

M&L Pulverizes fly ash bricks using class 'A ' old size bricks straigth or curved on plan exc 6m mean radius built in CM (1:6) cmplete all as specified and directed.

M&L Brick Work pulverizes fly ash bricks ,Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

M&L Formwork to Soffits of suspended slab such as Roof slab, Floor slab, landings and similar works horizontal or sloping etc., not exceding 200mm thick ,flat rough finished surfaces of concrete, complete all as specified and as directed.

S&F for 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed.

S&F 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009 complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening with and including 3 Nos. stainless steel butt hinges 75mm long complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed.

M&L Steel Work in Tubular /hollow section as in Trusses and post including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-4923 grade YSt.-240 complete all as specified and as directed.

M&L Framed Work such as Grills, Gratings, etc. with ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework of Water Tanks and Similar Work, conforming to Fe-290, Gde-E-165, complete all as speci-fied and as directed.

S&F Mild steel angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Fixing only PVC coated chain link fencing mild steel galvanised 3.00mm dia (minimum weigth 3Kg/Sqm) of wire and spacing 75mm x 75mm including line wires to any standards, rails and straining bolts including provision of binding wire complete all as specified and directed. Note :- Line wire ,binding wire and bolts/nuts shall be measured and paid separetaly under relevant item of BOQ

Supply only PVC coated chain link fencing mild steel galvanised 3.00mm dia (minimum weigth 3Kg/Sqm) of wire and spacing 75mm x 75mm including 8mm dia round bar as in line wires to any standards, rails and straining bolts including provision of binding wire complete all as specified and directed.

M&L Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut of 11 to 15mm dia, and 5cm to 10cm long complete all as specified and directed.

M&L Framed work as in doors or gates of angles or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering running rails and guides) and hanging also fastening and fixing complete Fe 410 -w(Gde E-250) quality B) complete all as specified and as directed.

M&L Mild Steel Plain Black Sheet 1.6mm thick in Hearths, covering to Door Shutters, covering to steel gates, etc. cut to size edges beaded if directed, holes punched including round headed Screws Clout screws including bending, turning up, mitred angles, stopped ends, outlets, etc. as required, as in repair complete all as specified and as directed.

S&F Steel rolling shutter with thickness of latch 1.25mm without ball bearing as specified including top cover anchoring rod, hasp & staple and one shop coat of primer , erected in position , push pull of manual type including taking down old one complete all as specified and as directed.

S&F Safety lever locks mild steel with 4 levers for rolling shutters as in repair complete all as specified and as directed.

S&F Ball bearing for rolling shutters as in repair complete all as specified and as directed.

Overhauling and greasing of rolling shutter of any size and pattern including scrubbing down old greasing for proper functioning, area of each shutter nexc 7 Sqm each complete all as specified and as directed.

Overhauling and greasing of rolling shutter of any size and pattern including scrubbing down old greasing for proper functioning, area of each shutter exc 7 Sqm but n exc 12 sqm complete all as specified and as directed.

Overhauling and greasing of rolling shutter of any size and pattern including scrubbing down old greasing for proper functioning, area of each shutter exc 12 Sqm complete all as specified and as directed.

S&F MS locking plate of standard size and shape from approved quality with a coat of red oxide primer including taking down of old one complete all as specified and as directed.

S&F Rolling shutter profile of 1.00mm thick MS sheet with a coat of red oxide primer (shope coat) minimum width of profile 75mm including taking down old one complete all as specified and as directed.

S&F Spring of rolling shutter of approved quality and size including taking down of old one complete all as specified and as directed.

S&F Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossing with and provision of galvanised mild steel wire staples or steel pins etc (each line wire to be measured entanglements aprons,barriers,gates etc including restraining resceuring and making good to staples as in repair.complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Welded steel wire fabric weight not more than 4Kg/Sqm fitted by mild steel nails complete all as specified and directed.

M&L False ceiling with 'E' board "Classic" , reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium powder coated snap grid to support the boards/files with aluminium anodised main 'T' section 35mm x 25mm x 1.50mm cross tee 25mm x 25mm x 1.50mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides duly suspended with 4mm dia GI hanger fixed with GI hooks 4mm dia and fastner as required at the site and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete all as specified and as directed.

S&F 40mm bore MS tubing medium grade and fixed at wall for ceiling complete all as specified and directed.

M&L Pressed steel frames for doors with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note :- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate

M&L Pressed steel frames for doors with one or more rebates size of frame 105 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note :- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate.

S&F Powder coated Aluminium anodised doors, windows, partitions and ventilators using aluminium sections of size and type approved by Engineer-in-Charge including jointing cleats, snap beading etc, complete all as specified and as directed.

S&F Powder coated anodised aluminium door shutters, aluminium section weighing 1.00kg/m (minimum) thickness not less than 2.00m including necessary jointing cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door shutters, floor hinges, powder coated aluminum snap beading screws etc. complete all as specified and directed.

M&L 1.50mm thick power coated aluminium , three track sliding window with three nos shutters made of aluminium section as per drawing no CWE/KOL/TD-33 of section no 1F-1F including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos , anodised aluminium snap beading screws etc.Complete all as specified and as directed. Note Nos :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window. (ii) Only Glass for window & wire mesh shall be measure and paid separately under relevant items of BOQ .

S&F Powder coated aluminium ventilators with louvers and glazing including frame of section over all size of window 600X450mm complete with following specification . (a) Alu frames of size 45x45x1.2mm (b) Rail & Stile 45x45x1.2mm thick (c) 4.80mm thick frosted sheet glass Note :- All ventilators/louvers member including fitting & fixture shall be deem to included quoted rate. Only measure opening size of ventilators/louvers

S&F Butt Hinges extruded brass,bright polished size of Hinges 100 mm (medium weight) and fixed with brass hinge pin complete all as specified and as directed.

S&F Aluminium anodized, Barrel Tower Bolt 200mm long, Extruded Section and fixed, complete all as specified and as directed.

S&F 300mm long Aluminium alloy, anodised, Sliding Door Bolt with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Aluminium alloy Handle 150mm long, Extruded Section, Fabricated type, anodized and fixed, complete all as specified and as directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring (overall length of cover plate 150mm) complete all as specified and as directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L Water Proofing Treatment on existing cleaned RCC Roof with the following Specifications and Manufacturer's instructions, complete all as specified and as directed :- (a) Rendering 10mm thick in Cement Mortar 1:3, when concrete is steel green including WPC even and smooth and shall be cured properly for 07 Days by Ponding of water over Roof. (b) Preparing and cleaning of fully dry surface as per IS:3067-1966. (c) Applying Bitumen Primer conforming to IS-3384-1986 over the Cleaned Plastered Surface @ 0.40 Litre per Sqm. (d) Applying a layer of APP based Polymeric Membrance; modified prefabricated five layer ,3.0mm thick (minimum) weighing 3.60 Kilogram per Square Metre (reinforced) with Polyster Non Woven Fabric weighing not less than 160 Grams per Square Metre by Torch application. The overlaps shall be minimum 100mm on the Transverse direction and 75mm on Longitudinal direction. (f) Applying two coat of bitummen based UV paint with Aluminium finish @ 0.11 Litre per Sqm over APP based Polymeric Membrane.

M&L Cement Concrete type D2 (1:4:8) using 40mm graded aggregate 75mm thick in Sub-bases, finishing concrete surfaces fair and even, complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

M&L Cement Concrete type B1 (1:2:4) (20mm graded aggregate) 50mm thick, laid in panels as in hard standing concrete surfaces even and smooth complete all as specified and as directed.

M&L Cement Concrete type B0 (1:2:4) (12.5mm graded aggregate) 25mm thick, in Flooring, finishing concrete surfaces even and smooth complete all as specified and as directed.

M&L Prepolished Coloured Cement Concrete designers Chequered Tiles 300 x 300x 25 mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles complete including 20 mm screed bed in CM (1:6) of thickness complete all as directed.

M&L Prepolished Coloured Cement Concrete designers Chequered Tiles 300 x 300x 25 mm thick, on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

M&L joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:6 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges, complete all as specified and as directed.

M&L Glazed Ceramic Coloured Tile 450x350x7mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar on fair faces of brick work or concrete surface of wall in two layer, first layer 5 mm thick in cement morter (1:4) and top layer 10mm thick in cement morter (1:4) using water proofing compound and finishing the surface even and smooth without using extra cement complete all as specified and as directed. . (NOTE:-WPC shall be measured and paid separately)

M&L Applying polymer modified cement mortar rendering 20mm thick in CM 1:3 on wall duly mixing polymer modifier "Nitobond SBR of M/s Forsoc Chemical India (Pvt) Ltd" or "Hind Styrene BR of Hindcon Chemical Ltd" or equivalent make of M/s Pidilite Industries @ 7 Litre per bag of cement complete finished even and smooth without using extra cement as per manufacturer's specification complete all as specified and directed.

Cutting out existing cracks in concrete surfaces forming grooves of 25mm x 40mm size, cleaning the groove thoroughly with blower, applying primer coat of the mix of IPH CC Resin & Hardner in equal proportion with suitable brush to form a film on the surface of groove, filling the groove with putty made by mixing IPH CC Resin, Hardner and admixture in the proportion of 1:1:4 and finally applying the sealing coat of the same mix and in the manner primer coat is applied with following min. coverage per running metre length of groove :- Material Priming Coat Putty Filling Seal Coat Resin 60 Gms 100 Gms 40 Gms Hardner 60 Gms 100 Gms 40 Gms Admixture - 400 Gms -

M&L rendering 15mm thick in CM (1:6) on other than fair faces of brick work or concrete surfaces even & smoth without using extra cement complete all as specified and directed.

M&L rendering 5mm thick in CM (1:3) as in ceiling/chajjas surfaces even & smooth without using extra cement complete all as specified and directed.

"Supply only" liquid water proofing compound (ISI marked) complete all as specified and directed. Make:- STP NO 1/ PEDILITE(DR FIXIT)/ FOSROC/ CICO/ SIKA

S&F 4.00mm thick sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F 4.80mm thick tinted sheet glass , pin head type and glazing in squares exc 0.5 sq. M in each pane complete all as specified and as directed.

S&F Frosted Glass 4.0mm thick, Pin Head type and glazing with Wooden Beads or Oil Putty in Square or Rectangular, not exc. 0.50 Sqm, complete all as specified and as directed.

M&L preparing new Surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Complete removal of old decorated surfaces and on walls and applying Three Coat of White Wash (any colour/ tint) complete all as specified and as directed.

M&L Complete removal of old decorated surfaces on ceiling and applying Three Coat of White Wash (any colour/ tint) complete all as specified and as directed.

M&L Preparing old decorated Plaster Surfaces of Wall and applying One Coat of White Wash (any colour/ tint) complete all as specified and as directed.

M&L Preparing old decorated Plaster Surfaces of Ceiling and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing old decorated plastered surfaces of Walls and applying One Coat of Cement Base Paint complete all as specified and as directed.

M&L Preparing new Surfaces of Walls and applying Two Coats of Cement Base Paint over a coat of primer complete all as specified and as directed.

M&L Preparing new Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 3mm thick BIRLA/JK water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L Preparing new Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 3mm thick BIRLA/JK water proof wall care putty including rubbing with emmery paper to make ceiling surface smooth and even complete all as specified and directed.

M&L Preparing old decorated Plaster Surfaces of Wall and applying One Coat of oil bound distemper (any colour /tint) complete all as specified and as directed.

M&L Preparing old decorated Plaster Surfaces of Ceiling and applying One Coat of oil bound distemper (any colour /tint) complete all as specified and as directed.

M&L Complete removal of old decorated surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L Preparing newly plastered surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L Preparing old decorated plastered surfaces of Walls and applying One Coats of Exterior Emulsion Paint Weather Coat (any colour /tint) (as per Manufacturer’s instructions), complete all as specified and as directed. Make- Asian (apex ultima), Berger Paints-Weathercoat Lifelong7 ,Dulux Paints-Wheathershield Ultraclean

M&L Preparing new Wood and Wood Based Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Pink Primer, complete all as specified and as directed.

M&L Preparing old Wooden Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L Preparing old Steel Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

S&F 20mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F 25mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F Chromium plated Bib taps for 15 mm bore of pipe as in repair complete all as specified and directed. Make : Essco (MQT-511KN) or equivalent make specified in the particular specification

S&F Brass chromium plated long body bib cock with Wall Flange screwed for 15 mm bore pipe as in repair complete all as specified and directed Make : Essco (MQT-512KN) or equivalent make specified in the particular specification

S&F Brass chromium plated two in one tap with Wall Flange screwed for 15 mm bore pipe as in repair complete all as specified and directed Make : Essco (MQT-512ANKN) or equivalent make specified in the particular specification

S&F Brass chromium plated Pillar Tap screwed for 15 mm bore pipe as in repair complete all as specified and directed Make : Essco (MQT-508KN) or equivalent make specified in the particular specification

S&F 15mm bore brass chromium plated Angular Valve with Wall Flange as in repair complete all as specified and directed. Make : Essco (MQT-526KN) or equivalent make specified in the particular specification

S&F 15mm bore brass chromium plated Stop Valve (concealed type) with Wall Flange as in repair complete all as specified and directed. Make : Essco (MQT-514AKN) or equivalent make specified in the particular specification

S&F Chromium plated Health faucet with 8mm Dia, 1.2 Meter long flexible tube and wall hook with N.R.V (Back Flow Preventer) as in repair complete all and specified and directed Make:- Essco (CAT No. ALE-ESS-583) or equivalent make specified in the particular specification

S&F Vitreous China Colour Wash down Water Closet Pan (Pedestal Pattern) with "p" or "s" trap front or back inlet including fixing Bolts with and excluding 10 litre capacity low level Flushing Cistern matching with water closet colour with inlet ball valve float handle and providing 32mm dia PVC flush pipe including plastic water closet seat with flat botton cover (coloured) fixed with mild steel chromium plated or aluminium hinging device including taking down old unserviceable one complete all as specified and as directed. Make -Essco Model No-ECS-WHT-551PSPP or equivalent make as specified in the particular specfication.

S&F Vitreous China White Squatting Pan ‘ORISSA’ Pattern, size 580x440mm with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan including Flushing Cistern and Flush Pipe, fixing with and including provision of cement Concrete Bedding as in repair complete all as specified and as directed. Make - Hindwire cat No 20042 or equvilant of approved make specified in particular specification.

S&F White PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Syphonic Action type with Inlet, Ball Valve, Float and Handle including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 and fixed as in repair complete all as specified and as directed. Make : Parryware Model No- C-8090, Cera cat part No CONGO B1010109 or equivalent model as specified in Particular Specification here in after.

S&F PVC Conncetions 15mm size with PTMT Nuts of length 450mm complete all as specified and as directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 500Litre Capacity (Cylindrical Vertical with Closed Top), White in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nipples with check nuts for inlet, outlet wash and overflow pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, and 15mm dia PVC waste pipe, including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including taking down old unserviceable one complete all as specified and as directed. Make - ESSCO(ECS-WHT-801 or equivalent make as specified in the particular specfication.

S&F Vitreous China White Urinal, flat back of size 465x355x265, complete including providing and fixing plugs, bedding urinal against Wall in Cement Mortar 1:2, securing urinal to plugs, grating with and including 60mm long brass screws, pointing around urinal back in cement fixing with 40mm dia PTMT waste coupling including PTMT Urinal spreader any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) etc complete all as specified and as directed. Make - Hindware Model No-600001 or equivalent Jaquer/Cera/ Parryware etc.

S&F UPVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), Type "B" single socketed, in any length with Rubber Ring Joints fixed to Walls, as in repair complete all as specified and as directed.

S&F UPVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), Type "B" double socketed, in any length with Rubber Ring Joints fixed to Walls, as in repair complete all as specified and as directed.

S&F UPVC (SWR) Bend 110mm bore (dia), any type, and Jointing with Solvent Cement, as in repair complete all as specified and as directed.

S&F UPVC (SWR) Junction 110mm bore (dia), Single (Single T) equal or unequal and Jointing with Solvent Cement, as in repair complete all as specified and as directed.

S&F UPVC (SWR) Nahani/Floor Trap 75mm bore (dia) Outlet, Plain with Grating and Jointing with Solvent Cement, as in repair complete all as specified and as directed.

PINKY CO.