GE/863/EWS-T-85/2019-20

Amount

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillet complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in Unframed work or Framed work complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quions, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Dismantling water tanks of capacity exc 250 & n exc 500 litres and removing to store complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware) 150 mm dia set in cement mortorcomplete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Demolition of Re-inforced Cement Concrete in any position and any description including cutting of reinforcement bars to facilitate demolition complete all as specified and directed.

Demolition of stone walling/boulder masonary , laid dry complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sqm but not exceeding 4.00 sqm each,with shutter (without taking off shutter from the frame) complete all as specified and directed .

Taking down chowkats or frames not exc 1.5 sqm each ,with shutter (without taking off shutter from the frame) complete all as specified and directed by Engr-in-charge.

Dismantling of wrought iron or mild steel work any description and fixed in any position complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard / dense soil complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in hard / dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

S & F 6 mm thick (5 Nos of ply) plywood BWR grade, type – BB, fixed with nails to timber frame as in ceiling, flat or sloping and similar location complete all as specified and directed.

S & F 2nd class hard wood (SAL) in scantling, clean sawn in any position and any description as in framed or unframed work complete all as specified and directed.

M&L for clean sawn second class hard wood for scantling as in framed or unframed work but except timber complete all as specified by Engr-in-Charge.

S & F of 2nd class soft wood (CHIR) plain fillets, bull nosed, splayed, chamfered or rounded on one face or edge, clean sawn, secured with nails sectional area exc. 3 sqcm but not exc. 6 sqcm complete all as specified and directed.

M & L for block masonry with solid pre-cast cement concrete blocks made out of cement concrete 1: 3: 6 type C-1, using 20 mm graded stone aggregate, exc. 10 cm in width and setting in cement mortar 1 : 6 complete all as specified and directed.

M &L for 75 mm thick cement concrete type C-2, 1:3:6 using 40mm graded stone aggregate finishing surface even and smooth without using extra cement as in plinth protection complete all as specified and directed.

M & L for providing 25 mm thick cement concrete 1:2:4 type B0 Nominal Mix (using 12.50 mm graded stone aggregate) as in sub base of floor, etc and finishing surfaces of concrete even and rough to receive the topping layer complete all as specified and directed.

M & L for machine cut kota stone slab flooring 20 - 25 mm thick over and including 20 mm thick screed bed laid in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for treating the kota stone slab surface with beeswax polish complete all as specified and directed .

M & L for Glazed ceramic coloured tiles of size 300 mm X 200 mm X 7 mm thick as on vertical surfaces such as skirting, dados and rises to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles including redering 10 mm thick on concrete surfce as in backing coat for laying wall tiles in CM 1:4 complete all as specified and directed.

M & L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

S & F of rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters, running rails and guides for sliding doors fixed with angle cleat and other connecting plates confirming to Fe – 410 (Gde E-250 ) Quality ' B' complete all as specified and directed.

S & F MS Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

M & L for plain cement concrete (1:2:4) (using 20 mm graded stone aggregate), as in lintels upto 1.5 m clear span, cills, steps,seismic and other similar bands, plinth course, string courses, lacinng courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for providing reinforced precast cement concrete (1:2:4) type B-1 (using 20mm graded stone agg) as in cover slab for manholes & septic tanks with plane face set in CM (1:6) complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in Chajjas complete all as specified and directed.

S & F of 0.63 mm thick galvanized corrugated iron (CGI) sheeting with two corrugation side lap using grade of zinc coating -275. inclusive of both sides, fixed with ‘L’ or ‘J’ type hooks or cranked hook / bolts and washers as in roof covering etc. complete all as specified and directed.

Fixing only 0.63mm thick galvanised corrugated MS sheeting with two corrugation side lap, fixed with J/L hook in roof complete all as specified and directed .

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, bands, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges in rough finished flat surface of concrete complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or secure complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and including binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F for 2nd class hard wood plain, solid, straight chowkats and frames, wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F factory made 2nd class hard wood rail and style Plain, framed, panelled shutters 40 mm thick ( two panels), with lock rail ad panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces . The size of rail and stile as per IS 1003 (Part I ), kiln seasoned and chemically pressure treated complete all as specified and directed.

S & F II class hard wood Plain, framed, pannelled shutters 35 mm thick (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers etc complete all as specified and directed.

S&F II class hard wood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed .

-Ditto- but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers

S & F 30 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter as specified in clause No. 8.24 (b) of MES schedule part – I (Specifications - 2009) complete all as specified and directed.

S&F for IInd Class hard wood of Small fittings such as brackets of any type, latch and hing blocks, shaped door & window stops & the like, including all necessary labours; articles n exc 200 cu.cm each complete all as specified and directed.

M&L PCC 1:2:4 type B1 (20 mm graded aggregate) as in bed plates complete all as specified and directed.

S & F MS flat iron bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gate, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fast, wall ties, hooks for hanging fans and other similar small steel article conforming to Fe – 290 Gde E -- 165 complete all as specified and directed.

M & L for preparation of surface of wood and wood based materials, steel or iron work, new or old of any description or girth not otherwise described, and treated with tar or coal tar black paint as in ends of posts, back of chowkhats etc. area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm each complete all as specified and directed.

M & L for preparation of surface of wood and wood based materials, steel or iron work, new or old of any description or girth not otherwise described, and treated with tar or coal tar black paint as in small articles such as stop, covers, gully gratings, holdfasts, ende of posts, back of chowkats, etc. area tarred not exc. 0.10 Sqm each complete all as specified and directed.

Supply & fixing MS barrel tower bolt of 150mm long stove enamelled black with bright bolt complete all as specified and directed.

S & F of 125 mm long (Length of bolt) mild steel barrel tower bolts, stove enamelled black, with bright bolt complete all as specified and directed.

S & F of 250 mm long (Length of bolt) mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F 125mm long MS butt hinges medium weight cold rolled complete all as specified and directed.

S & F 100 mm butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 75mm long MS butt hinges medium weight cold rolled complete all as specified and directed.

S & F 150mm mild steel pressed handles , oval type, stove enamelled black complete all as specified and directed.

Supply & fixing MS pressed handle oval type stove enamelled black of 125mm long fixed with screw to shutter complete all as specified and directed.

Supply & fixing 300 mm ,Mild steel ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F for galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S & F of 4 mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads in square not exc. 0.5 Sqm in each pane complete all as specified and directed.

M & L for preparation of new wooden surface any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint over a coat of prink primer all as specified and directed.

M& L for one coat of synthetic enamelled paint on old steel surfaces exc 10cm width or girth including preparation of surfaces complete all as specified and directed.

M & L for preparation of new or previously untreated surfaces of steel of any description , over 10 cm in width or girth not otherwise described applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and directed.

M & L for chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick, set, jointed and pointed in neat cement slurry over and including 20mm thick screed bed in cement mortar 1:4 as in floors with grey cement and pigment complete all as specified and directed.

M&L for precast PCC 1:3:6 type C1 using 20mm graded stone agg as in bond stone set in cement mortar 1:6 complete all as specified and directed . Note :- The quantiry of bond stone used in the wall shall be deducted from stone masonry .

M & L for providing, cement concrete cast in situ 1:2:4 , type B1 (Using 20 mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edge including form work complete all as specified and directed.

M & L for walling of random rubble stone masonry, un-coursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 complete all as specified and directed.

M & L for walling of random rubble stone masonry (EXCEPT STONE), un-coursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 complete all as specified and directed. Note: - old stone obtained from demolition shall be used under this item.

M & L for Raised pointing to random or polygonal rubble, uncoursed or buought upto course in cement mortar 1:3 to walls complete all as specified and directed.

M & L for rendering 15mm thick on fair faces of brick or concrete surfaces or PCC block walling in cement plaster 1:4 and finished even and smooth (without using extra cement) complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick or concrete surfaces or PCC block walling in cement plaster 1:6 and finished even and smooth (without using extra cement) complete all as specified and directed.

M & L for 10 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing the surface even and fair complete all as specified and directed.

M & L for preparing newly plastered or previously untreated walls surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M&L for two coat of oil bound distempering over priming including preparation of new wall surface complete all as specified and directed.

S & F PVC (SWR ), pipes of 110 mm dia single socketed , in any length with rubber ring joints , laid in trenches or in floor complete all as specified and directed .

S & F PVC (SWR ), pipes of 110 mm dia single socketed , in any length with rubber ring joints ,fixed to walls or fixed in retaining wall as spout pipe complete all as specified and directed .

S&F PVC (SWR) junction double , (double 'T') , equal or unequal with access door complete all as specified and directed.

S & F PVC (SWR ) vent cowl for 110 dia pipe complete all as specified and directed

S & F PVC (SWR) 'S' trap of 110/110 mm dia complete all as specified and directed .

M & L PVC (SWR) floor trap 75 mm dia of outlet , plain with grating including jointing with solvent cement complete all as specified and directed.

S & F 20mm bore tubes 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Fixing only 20mm bore tubes any grade to walls and ceilings or laying in floors complete all as specified and directed.

S & F 15mm bore tubes 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S & F 500 litres capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S & F in repair 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repair 20mm bore ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

M & L for preparation of new plastered surface of wall and applying three coats of white wash complete all as specified and directed.

S & F in repairs vitreous china wash down water closet pan (pedestal pattern) white complete all as specified and directed .

S & F plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging deviced complete all as specified and directed .

S&F in repairs of Indian type WC vitreous China squating pan, 'Orissa' pattern, white with integrated foot rest including provision of lime concrete bedding .complete all as specified and directed .

S&F PVC low level flushing cistern 10 Ltr capacity incl float valve and flush pipe complete all as specified and directed.

S & F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S & F in repairs 15mm bore bib taps, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs stop valves, 15mm dia chromium plated, fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F PVC connections 15mm size with PTMT nuts of lengh 450 mm complete all as specified and directed.

M & L for Gully traps salt glazed stoneware (SGSW) square or round mouthed type 'P' of size 180x100mm for drain pipes complete all as specified and directed.

S & F towel rail 450 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum wt 170 gms) complete all as specified and directed.

M&L for 150 mm internal dia salt glazed stone ware pipe Grade 'A' laid in trenches and jointed complete all as specified and directed.

M& L for PCC 1:4:8 type D-2, (using 40mm graded stone aggregate) as in bed of drain for 150mm bore pipe incl packing under and completely surrounding pipes with concrete after they are laid and tested for 150mm dia pipes complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D2, using 40mm graded stone aggregate as in surface of flooring all as specified and as directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone agg as in foundation, filling and mass concrete of retaining walls complete all as specified and directed.

Taking down carefully copper/aluminium point wiring from existing points (light, fan, socket or power) alongwith compete fittings such as switches ,ceiling rose, pendent holder, sketch fitting & regulator etc. including making good to the disturbed surfaces of wall, roof and floor etc. to match with the existing surfaces complete all as specified and directed.

Taking down unserviceable service cable any size removing from the pole to main DBs complete all as specified and directed .

Taking down unserviceable main switches, DBs with MCB SP/Isolators by unscrewing form board complete all as specified and directed.

M&L for point wiring using approved colour coding as per IS with 1.5 Sqmm multistranded,1100 volt grade copper conductor FRLS cable of PVC insulated and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable FRLS for continuous earthing in & incl PVC casing & caping with accessories having ISI mark fixed on wall surfaces / ceiling including provision of PVC Box on top for fixing switches sockets etc. for one light point/ fan /Bell point controlled by one switch complete all as specified and directed .

All as per Srl item No 110 here-in-before but controlled with one 3 pin socket outlet 15 Amp, independent board with cable 2.5sqmm including provision of 1.5 sqmm single core multistranded PVC insulated copper conductor as earth conductor

All as per Srl item No 110 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the independent board with other switches with cables 1.5 Sqmm

All as per Srl item No 110 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the same board with other switches with cables 1.5 Sqmm

Supply and fixing of switch piano type 15 Amp, 230 Volt, flush button single pole one way complete all as specified and directed .

Supply and fixing of socket outlet 3 pin 15 Amp 2-in-one 230 Volt flush type complete all as specified and directed .

Supply and fixing of socket outlet 3 pin 5 Amp 2-in-one 230 Volt flush type complete all as specified and directed.

Supply and fixing of switch piano type 5 Amp, 230 Volt, flush button single pole one way complete all as specified and directed .

M&L Ceiling rose, 3 terminal with ISI mark all as specified and directed ..

Supply and fixing surface & wall mounted LED 20W tube light fitting batten 4 feet with extruded aluminium housing and robust construction 20W system lumen with all accessories complete all as specified and directed . Make: Wipro Cat No. LL20-221-xxx-65-NE or equivalent of Bajaj and CG/Philips

Material and labour for lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings. Make : Anchor/leader/havells

Supply and fixing LED lamp 9 W ,system lumen (NOM) 600 with all accessories complete all as specified and directed.

Supply & Fixing bulk head light with 10 W LED Lamp complete all as specified and directed. Make: Bajaj Cat No BIBWP 10W LED or equivalent of Wipro and CG/Philips

Supply and fixing of sheet metal enclosure double door for DBs single pole and neutral for 8 way 240 volt complete all as specified and directed .

S&F MCB SPN 40 Amp,10 KA complete all as specified and directed.

S&F MCB SP 6 Amp to 32 Amp, 10 KA. complete all as specified and directed.

Supply and fixing 1100 Volts grade heavy duty FRLS cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire one twin core cable flat or circular of size 16 Sqmm complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth wire 4 mm dia as earth continuity coductor by means of bolts, nuts, check nuts and washers of galvanised iron or steel ,GI earth strip protected by GI medium grade pipe 40 mm dia all as shown in electrical plate No. 3 ,connected to earthing test point complete all as specified or indicated including testing on completion or any other equipment with provision of GI pipe light grade etc all as specified and directed including necessary excavation and earth work in hard/dense soil, returning filling, disposal of surplus soil up to 50 M, provision of concrete pit in PCC (1:2:4) type B1 using 20 mm graded stone aggregate with 40 mm thick cover of RCC 1:2:4 using 20 mm graded stone aggregate, reinforced with XPM (weight not less than 4 kg/sqm) and frame of angle iron 40x40x6 mm with 6 mm dia bar handle made to shape duly exposed surface painted with 2 coats of synthetic enamal paint over a coat of primer, necessasry form work, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 meter long placed on top edge of earth plate, common salt and charcoal filling, test point made out of bronze/ gun metal with fixing arrangement, funnel, wire mesh etc. complete all as specified and directed. Note: Earth continuity conductor beyond 7.5 mtr shall be mearured and paid separately.

Supply and fixing LED lamp 12 W system lumen (NOM) 600 with all accessories complete all as specified and directed . Make:Cromptom Cat part No-LED 12DFCDL-PRO-BO or equivalent of Bajaj/Philips/wipro

S&F in repair Exhaust fan heavy duty,1400 RPM, AC, Single Phase,300mm sweep,with louvres complete all as per specified and directed .

Supply & fixing in repair, water heater storage type of capacity 25 liters with 5 STAR BEE rating,multifunctional safety valve, electric operated 230 V, Single Phase complete including one no of heating element, automatic thermal cut out, fusible plug, anti vacum sys, built in presser release valve,thermostat, rust proof powder coated body, indicator lamps and all safety advices as per E-in-C's Branch technical instructions and including provn of grouting bolts in walls including pillar cock , PVC connection etc and making good to disturbed surfaces and Testing complete all as specified and directed .

Supply and fixing in repair security light fitting 60 watt LED with lens, compact, security street light fitting with pressure diecast aluminium housing IP66 protection with high power LED as power source complete incl provn of PVC insulated unsheathed copper conductor twin core cable 1.5 Sqmm, 1.5 mtr long approx for connection Complete all as specified and directed . Make: Crompton Cat Part No LSTP -60-CDL or equivalent to Bajaj/Philips

M & L for submain wiring with cable insulated single core multistranded copper conductor cable 1100 volts grade 4 sqmm 2 runs and one run of 2.5 sqmm as earth wire drawn through & incl in PVC casing caping of suitable size medium grade complete all as specified and directed.

M & L sheet metal enclosure with two pin and earth plug and socket complete with single pole MCB 20 Amp, 10 KA including dismantling old one complete all as specified and directed.

Supply and fixing of sheet metal enclosure double door for DBs, single pole and neutral for 4 way 240 volt complete all as specified and directed .

Supply , installation, testing & commissioning of split AC 1.5 TR Capacity , 5 STAR, with inner / outer wall mounting units complete with cordless remote control, including all required accessories for installation to performing cooling & heating function & compressor with inverter technology and making electric connection complete all as specified and directed.

Supply & fixing voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 180 V to 280 V with putput voltage stabilized at 230 v with accuracy of + 2.5 % and of capacity 5.0 KVA & wall mounting type complete all as specified and directed.

Supply and fixing of 50 watt LED flood lights , energy saving, environmental friendly, long life, pressure die-cast aluminium, housing with high power LEDs as light source, suitable for highlighting architectural features or area lighting, IP66 with color temp 5000k with complete fixing from tubular pole with & including 1.5 mtr long & 2.50 sqmm service wire complete all as specified and directed.

Supply and laying or fixing or passing through pipe, 1100 Volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 sqmm 2 core nominal cross section in service connection complete all as specified and directed.

Net Contract Sum will be after deducting Sch Of Credit of Rs. 60,830.00

M/S Gulab Singh