REPAIR/REPLACEMENT TO ROOF TREATMENT TO LIFT MACHINE ROOM SLAB, RAILINGS, PLASTERING, FLOORING AND STRENGTHEN OF GUIDE RAILS AND OTHER ALLIED B/R REPAIR FOR LIFTS AT CARIAPPA VIHAR, MANEKSHAW MARG, TODAPUR, NARAINA VIHAR, MOHAN ENCLAVE, 505 ABW ETC

Amount

SECTION - I

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and as directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

S&F of Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed. (Make:- Tata Blue Scope/ Indian Ispat/JSW)

S& F of Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed. (Make:- Tata Blue Scope/ Indian Ispat/JSW)

Dismantling of structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed.

S&F Rolled section as in main and cross beams, hips and jack rafters, purline where connected to common rafters and running rails and guids for sliding doors fixed with angle cleats or other plates, conforming to Fe 290 grade E-165 complete all as specified and as directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS-1161(1979) grade ST-240 complete all as specified and as directed.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and as directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and as directed. (Make:- SOMANY / JOHNSON / KAJARIA / ASIAN/ NITCO.)

M & L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tile exc 0.36 sqm but not exc 0.42 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match to match the surface of tile complete all as specified and as directed. (Make:- SOMANY / JOHNSON / KAJARIA / ASIAN/ NITCO.)

Taking down granite (of any type) any thickness complete all as specified and as directed.

Material and labour for 20 mm thick black or any other colour granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including dismantaling old unserviceable one complete all as specified and as directed.

Materials and labour for machine cut kota stone slab flooring 18-20 mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete in riser of steps, skirting, dado and wall including dismantaling old unserviceable one complete all as specified and as directed.

Demolition of brick work or stone / boulder or concrete block masonry including all quoins, arches, pillars, etc. built in cement mortar complete all as specified and as directed.

M & L for brick work with sub class ‘B’ old size bricks locally available best quality, straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Taking down cement or cement lime plaster any description on any walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M & L for Rendering 15 mm thick on fair faces of brick work or concrete surface in CM (1:6), finished even and smooth without using extra cement complete all as specified and as directed.

M & L for Rendering 10 mm thick on fair faces of brick work or concrete surface in CM (1:4), finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over one coat of alkali resistant primer complete all as specified and as directed. (Make:- JHONSON & NICHOLSON/ SNOWCEM PLUS/ BERGER / ASIAN PAINT)

M & L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of chalk whitening complete all as specified and as directed. (Make:- JHONSON & NICHOLSON/ SNOWCEM PLUS/ BERGER / ASIAN PAINT)

Taking down chowkat or frame with shutter (without taking off shutter from the frame) exceeding 1.5 but not exceeding 4.0 sqm each complete all as specified and as directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

S & F of 1.25 mm thick pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and as directed. (Make:- M/s SK Steel Febricators, Ludhiana/ M/s Sehgal Doors, New Delhi/ M/s Bhawani Steel Febrcation Gaziabad/ M/s India Mart Intermesh Ltd/ Hyat Interriors)

M & L for Steel door including projecting type hinges, steel handle, complete, with glazing bars, dovetailed or welded complete all as specified and as directed.

Taking down PVC chowkats or frame with shutters (without taking off shutters from the frame) not exceeding 1.5Sqm each complete all as specified and as directed.

M & L for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specifications and drawing as shown on page No 180 of SSR Part -II complete all as specified and as directed. (Make:- SINTEX/ RAJSHRI PLASTIWOOD/ DURA PLAST/ FENESTA)

M & L for factory made solid PVC panel door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheety strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded.sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing as shown on page No 176 of SSR Part -II complete all as specified and as directed. (Make:- SINTEX/ RAJSHRI PLASTIWOOD/ DURA PLAST/ FENESTA)

Taking down carefully steel window/ventilators including shutter, grill and glass panes of any size and making good to the damaged/ disturbed surfaces while cutting holes complete all as specified and as directed.

S & F of steel window with side hung shutters including box type hinges with steel handle, hold fast and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

Ditto as per item above but without glazing bars complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed.

Supply and fixing sheet glass ordinary quality 5.5 mm thick type fixed to aluminium doors in squares exc 0.5 sqm in each pane complete all as specified and as directed. (Make:- MODIGUARD FLOAT/ SAINT GOBAIN/ TRIVENI FLOAT)

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe-290 Grade E-165 including dismantling old one complete all as specified and as directed.

S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S & F Sheet glass 4 mm thick , ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 sq.m in each pane complete all as specified and as directed.(Make:- MODIGUARD FLOAT/ SAINT GOBAIN/ TRIVENI FLOAT)

S & F of 100 mm long stainless steel butt hinges, medium weight complete all as specified and as directed.

S & F of 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed. (Make:- ARGENT/ CLASSIC/ BHARAT/ ALANS/ HATTICH)

S & F of 125 mm long extruded anodised aluminium alloy handle, fabricated type complete all as specified and as directed. (Make:- ARGENT/ CLASSIC/ BHARAT/ ALANS/ HATTICH)

S & F of 300 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy complete all as specified and as directed. (Make:- ARGENT/ CLASSIC/ BHARAT/ ALANS/ HATTICH)

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B-1 using (20 mm graded crushed stone aggregate) as in levelling course/ roof padding complete all as specified and as directed.

Complete removal of existing water proofing treatment over RCC roof, projections of any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with wire brush including removing debris from the site and depositing in low lying area where directed and providing following :- (a) Rendering 10mm thick in CM 1:3 on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing of water proofing compound @ 2% by weight of cement. (b) Apply a coat of bituminous primer confirming to IS-3384@ 0.4 ltr/Sqm on newly plastered surface after curing as per IS-456 and dried. (c) After the primed surface has dried, apply a coat of hot blown bitumen(85/25 penetration) confirming to IS-702 @ 1.2 Kg/Sqm of the surface. (d) Provide polymeric water proofing membrane ISI marked laid with overlaps, bonded with hot blown bitumen, and laid by torch application method, end overlaps shall not be less than 150mm and side lap 75mm. Polymeric water proofing membrane should be five layered with centre core as 90 micron high molecular high density polyethylene film, min weight 3 Kg per sqm. APP membrane shall laid acorss the slop from lowest line of sloping roof towards ridge. (e) Over the APP membrane, apply a coat of semi hot blown 85/25 penetration grade bitumen confirming to IS-702 @ 1.20 Kg/ sqm and blinded with fine sand in dry condition @ 0.50 Kg / Sqm dusted over the bitumen coat Note : (i) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface. (ii) Ponding test shall be conducted for 72 hrs as directed. (iii) PCC Levelling course and WPC shall be measured and paid seprately.

Supply only integral water proofing compound ISI marked complete all as specified and directed.

M & L in repairs for 15 mm bore Chromium plated fancy type Bip taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. (Make:- Jaguar/ GEM/ MARC/Parryware)

M & L in repairs for 15 mm dia Fancy type Chromium plated Angle valves, cast copper alloy screwed down high pressure, with crutch or butterfl y handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. (Make:- Jaguar/ GEM/ MARC/Parryware)

S & F in repairs PTMT 32mm dia waste coupling (half or full threaded), minimum weight 60 gms) fixed to stainless steel sinks complete all as specified and as directed. (Make- Prayag/ Polytuff)

S & F in repairs for 125mm dia PTMT grating doom with waste hole for waste pipe ( minimum weight 40 gram) complete all as specified and as directed. (Make- Prayag/ Polytuff)

S & F in repairs for 450mm long CP brass connection pipe with CP brass nuts on both ends for fixing to pipe or other fittings complete all as specified and as directed. (Make:- Jaguar/ GEM/ MARC/Parryware)

S & F in repairs for PVC waste pipe 32/40mm bore fixed to PTMTwaste coupling for kitchen sink complete all as specified and as directed. (Make- Prayag/ Polytuff)

Supplying and fixing in repair for vitreous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed.(Make:- Hindusthan Sanitary Wares/ Jaguar/ Cera/ Parryware)

S & F in repairs PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve foat and handle including brackets 10 litres complete all as specified and as directed.(Make:- Hindusthan Sanitary Wares/ Commander/ Cera/ Parryware)

Supply and fixing in repairs viterous China wash basin, white flat back, size 550x400mm excluding taps, waste chain and plug and porcelan stopper but including brackets complete all as specified and as directed.(Make:- Hindusthan Sanitary Wares/ Jaguar/ Cera/ Parryware)

S & F in repairs for 15 mm bore brass CP wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed. (Make:- Jaguar/ GEM/ MARC/Parryware)

M & L for 75 mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in complete all as specified and as directed.

M & L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed. (Make of Paint & Primer:- ASIAN/ BERGER/ JOHNSON & NICHOLSON/ SHALIMAR)

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for 100mm thick cement concrete 1:2:4 (40 mm graded stone aggregate), type B-2 as in hard standing and footpaths complete all as specified and as directed.

M&L for 25mm thick cement concrete 1:2:4 (20 mm graded stone aggregate) , type B-1 as in flooring finished cement concrete surface even and smooth (without using extra cement) complete all as specified and as directed.

M & L for cement Concrete 1:4:8 type D2 (using 40mm graded agg) as in foundation filling and mass concrete, complete all as specified and as directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement including taking down old unserviceable one complete all as specified and as directed.

Excavating in trenches, not exceeding 1.5m wide and n.exceeding 1.5m depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. not exceeding 10 sq m on plan in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated materials n.exc 50M and depositing where directed at a level n.exc 1.5M above the starting point complete all as specified and as directed.

M&L for Salt-glazed stoneware drain pipes 150mm bore laid in trenches and jointed including taking down old unserviceable one complete all as specified and as directed.

M & L for Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:4:8 type D2 (using 40mm graded agg) for 150mm bore pipe complete all as specified and as directed.

SECTION - II

Taking down carefully existing surface/concealed unserviceable copper/Aluminium point wiring (light, fan socket or power) complete with fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing etc complete all as specified & as directed.

M & L for point wiring using 1.50 sqmm size FRLS, PVC insulated, unsheathed 1100 volts grade single core multi-stranded copper conductor cable in proper colour coding drawn into and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers except conduit junction box (junction box will be of MS) including one continuous run of PVC insulated (green colour) 1.50 sqmm size FRLS stranded copper conductor cable as in earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size for fixing modular switches/sockets/fan regulator etc , with and including Modular cover plates of suitable size and making good surface as original by plastering, whitewash/colour and distemper etc complete all as specified & as directed for the following :- Note : The cost of modular type Metal boxes and modular accessories like cover plates will be included in quoted rate. (Make of cable:- NICCO / FINOLEX / RR KABEL/ HAVELL'S/ POLYCAB / KEI INDUSTRIES LTD Make of Conduit:- FINOLEX / PAYAL/KALINGA/ PRESTO PLAST)

(a) one light point / fan point/ wall fan point controlled by one 5 Amp switch.

(b) one 3 pin socket outlet point 5 amps on the same board.

(c) one 3 pin socket outlet point 5 amps on the independent board.

All as per srl item no. 67 here-in-before but with 2.50 sqmm size FRLS, PVC insulated, unsheathed 1100 volts grade single core multi-stranded copper conductor cable and 1.5 Sqmm FRLS stranded copper conductor cable as earth wire for 15 Amp light point complete all as specified & as directed. Note : The point wiring for power point will not be mixed with light/fan point circuit or not in the same conduit pipe. (Make of cable:- NICCO / FINOLEX / RR KABEL/ HAVELL'S/ POLYCAB / KEI INDUSTRIES LTD Make of Conduit:- FINOLEX / PAYAL/KALINGA/ PRESTO PLAST)

Supply and fixing in replacement of Switch piano flush type, 5/6 Ampere single pole, one way complete all as specified and as directed. (Make : Anchor / Cona / Kinjal / Havells)

Supply and fixing in replacement of socket out let 2 in 1, 5 pin, 5/6 Amp universal type complete all as specified and as directed. (Make : Anchor / Cona / Kinjal / Havells)

Supply and fixing in replacement of Switch piano flush type, 15/16 Ampere single pole, one way complete all as specified and as directed. (Make : Anchor / Cona / Kinjal / Havells)

Supply and fixing in replacement of socket out let 6/16 Amp, flush type complete all as specified and as directed. (Make : Anchor / Cona / Kinjal / Havells)

S & F ceiling rose, 3 phase, PVC / polycarbonate, surface type, 65mm x 50mm, insulated body, three terminals complete all as specified and as directed. (Make : Anchor / Ess Ess Kay / Havells/ Cona)

Supply and fixing in replacement of LED tube light fitting 20 W to wall mounting type with and including all electric connections with two core PVC insulated, PVC sheathed copper conductor flexible cable complete all as specified and directed. (Make :Havells /Phillips / Surya Roshni Ltd / Bajaj/ Crompton Greaves/ C & S Electric)

Supply and fixing in replacement of LED tube light fitting 10 W to wall mounting type with and including all electric connections with two core PVC insulated, PVC sheathed copper conductor flexible cable complete all as specified. (Make :Havells /Phillips / Surya Roshni Ltd / Bajaj/ Crompton Greaves/ C & S Electric)

S & F in replacement of Energy efficient wall mounted LED bulk head luminaire 13.5W made of die cast Aluminium with Opal diffuser IP-65 complete all as specified and as directed. (Make:- Philips/Havells/ Wipro/ Halonix )

Tushar engineers

SHIVA ENTERPRISES