Improvement of Station Feeder Road including drain works of Pathsala town at Pathsala under SOPD(G) for 2019-20

Amount

Excavation in Cutting in Soil by manual means with lead upto 50 m Excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3 (Manual should be use where machines can not be deployed due to site condition)

Plant Mix Method (Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density,complete as per cl. 401( with an initial lead of 5 Km.)( Including cost of testing of materials at site and laboratory as directed by the deptt.) (ii) for grading II Material

Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sb-base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density (including carriage of mixed materials up to 10.0 Km initial lead from mixing plant )

Prime coat Prime coat (Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 1.00 kg/sqm using mechanical means.) ( Including cost of testing of materials at site and laboratory as directed by the deptt.) '(i) With bitumen emulsion-CSS-1hh

Tack Coat :- Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20kg per sqm on the prepared bituminous/ grannula surface cleaned with mechanical broom ( Including cost of testing of materials at site and laboratory as directed by the Deptt.) ii) With bitumen emulsion- CSS-1 (IS- 8887-2004 ) (b) dry & hungry bituminous surface

Dense Graded Bituminous Macadam (Providing and laying dense bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5% by weight of total mix and filler transporting the hot miox to work site,laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no. 507. complete in all respect. (including carriage of mixed materials up to 10.0 Km initial lead from mixing plant )( Including cost of testing of materials at site and laboratory as directed by the deptt.) (a) With hydrated lime / cement as filler (refer table 500-9 of MoSRT&H specification) & anti stripping agent as per IS:14982 (Refer Appendix-5 of MoSRT&H specification)(I)'with 60/70 or VG-30 grade bitumen (i) for Grading I ( 13 mm nominal size )

Bituminous Concrete (Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 % of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.509. complete in all respect. (including carriage of mixed materials up to 10.0 Km initial lead from mixing plant )( Including cost of testing of materials at site and laboratory as directed by the deptt.) (a) With hydrated lime / cement as filler (refer table 500-9 of MoSRT&H specification) & anti stripping agent as per IS:14982 (Refer Appendix-5 of MoSRT&H specification)(I)'with 60/70 or VG-30 grade bitumen (i) for Grading I ( 13 mm nominal size )

Retro reflectorised Traffic sign: Providing and erecting of Retro-Reflectrorised cautionary, mandatory & informatory sign as per IRC: 67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand) 90cm equilateral traingle

Retro reflectorised Traffic sign: Providing and erecting of Retro-Reflectrorised cautionary, mandatory & informatory sign as per IRC: 67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand) 60cm equilateral traingle

Retro reflectorised Traffic sign: Providing and erecting of Retro-Reflectrorised cautionary, mandatory & informatory sign as per IRC: 67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand) 60cm circular

Retro reflectorised Traffic sign: Providing and erecting of Retro-Reflectrorised cautionary, mandatory & informatory sign as per IRC: 67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand) 80cmm x 60 cm rectangular

Providing reflective pavement marker with a provision of spike at the bottom with Micro prismatic lens in both direction having thermoplastic body adhering to the specification and guidelines of MoSRTH & H's fixed to the road surface using the adhesives and the procedures recommended by the manufacturers with three months replacement warranty and free maintenance.

Providing ‘Sparkle Solar Road Studs, manufactured by Tata B.P.Solar India Ltd. Of size (125mmx125mm), 90mm height (from bottom of shank to the top of stud) with detachablebattery, m6LEDsthree on each side for Bi-directional studs/3 LEDs on one side for unidirectional studs, ultra bright LED in amber and red colour, weight per stud 700+25 gms, flash rate of 50-65 times per minute completely water resistant and weather proof with replacement warranty and free maintenance fro one year from the date of installation of stud on road-(installation should be made using adhesives and procedures recommended by manufacturer under the supervision of their competent technician). a) Bi-directional Stud

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

Kilo Metre Stone (Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc) ii) Ordinary Kilometer stone (Precast)

Cross Drainage Works Cleaning and de-silting of road side drains / cross drains etc. by mechanical means with adequate road safety measures by providing caution boards / safety ribbons /proper barricading where necessary / proper lighting if necessary etc. without damaging the foot paths / slabs / road surfaces etc including immediate disposal of the semi liquid / silt / garbage/Floating materials/ Polythin etc. taken out from the drains/ culverts etc. upto a lead of 20.00 KM from the site within 24 hours as directed keeping the road surface / footpath etc. clean and as directed by the department . De-siltation work will have to be carried out as and when necessary as directed by the Engineer-in-Charge. (Measurement shall be taken on inside of the drain wall )

Dismantling of Structures (Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material,disposal of unserviceable material and stacking the serviceable material with all lift and lead of 1000 metres) 'By Mechanical Means for items No. 202.

Excavation for structures Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, constructing of shoring and bracing, removal of slumps and other deleterious matter, dressing of sides and bottom, backfilling with approved material. I ) In ordinary soil B)Mechanical Means. (ii)Depth up to 3.00 m (with dewatering)

Removal of Unserviceable Soil with Disposal upto 1000 metres ( Removal of unserviceable soil including excavation, loading and disposal upto 1000 metres lead but excluding replacement by suitable soil which shall be paid separately as per clause 305 ). Quantity = Same as item no. 1 above

Dry rubble flooring. Construction of dry rubble flooring at cross drainage work for relatively less important works.

PCC 1: 3: 6 in Foundation. Plain cement concrete 1: 3: 6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation nand compacted by vibration including curing for 14 days.

Plain/Reinforced cement concrete, in sub structure complete as per drawing and technical specification and steel shuttering formwork

Reinforcement. Supplying, fitting and placing TMT bar reinforcement in sub- structure complete as per drawing and technical specification. (ii) With TATA make TMT rebar. TMT-IS 1786 ( Fe-500 D) Secondary Producer (ISI approved)

Back filling Back filling behind abutment , wing wall and return wall complete as per Drawing and technical specification. B. Sandy material

Weep Hole Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100mm dia AC pipe, extending through the full width of the structure with slope of 1 V:20 H towards drain face. Complete as per drawing and technical specification.

Traffic island Excavation for structures Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, constructing of shoring and bracing, removal of slumps and other deleterious matter, dressing of sides and bottom, backfilling with approved material. I ) In ordinary soil B)Mechanical Means. (ii)Depth up to 3.00 m (with dewatering)

Removal of Unserviceable Soil with Disposal upto 1000 metres ( Removal of unserviceable soil including excavation, loading and disposal upto 1000 metres lead but excluding replacement by suitable soil which shall be paid separately as per clause 305 ). Quantity = Same as item no. 1 above

Dry rubble flooring. Construction of dry rubble flooring at cross drainage work for relatively less important works.

PCC 1: 3: 6 in Foundation. Plain cement concrete 1: 3: 6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation nand compacted by vibration including curing for 14 days.

Plain/Reinforced cement concrete, in sub structure complete as per drawing and technical specification and steel shuttering formwork

Reinforcement. Supplying, fitting and placing TMT bar reinforcement in sub- structure complete as per drawing and technical specification. (ii) With TATA make TMT rebar. TMT-IS 1786 ( Fe-500 D) Secondary Producer (ISI approved)

Back filling Back filling behind abutment , wing wall and return wall complete as per Drawing and technical specification. B. Sandy material

Painting Two Coats on New Concrete Surfaces' Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces

Painting Two Coats on New Concrete Surfaces' Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces

Construction of Boundary wall Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Upto a depth of 2.00 m below the existing G.L. In ordinary soil

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a).Brick on flat soling.

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level). ISI approved super ductile TMT Bar

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level). ISI approved - M.S. Rod

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. Sides of tie beams, grade beams etc. at or below ground level.

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. Columns, Pillars, Posts & Strut

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b). In prop. 1:4:8 (1 cement:4 coarse sand : 8 coarse agg. by volume (using mixture machine)

Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using mixture machine. In sub - structure up to plinth level. M15 or Prop. 1:2:4

Super-structure from plinth level upto 1st floor level. Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M15 or Prop. 1:2:4

112 mm thick 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately). (a). In cement mortar in proportion 1:4.(1 cement:4 sand)

Providing, fitting and fixing M.S. grill including gate iron of requiredpattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws. I . Plain grill. (c). Fixed to Brickwork/P.C.C/R.C.C.

15 mm thick Cement plaster in single coat on rough side of single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. (b). In cement mortar 1:4

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new wall surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials.

Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. a). With ready mixed "red-lead/ red oxide" primer.

Applying primary coat over new steel and other metal surface upto 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. b). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Solar Street Lighting : Supplying including installation and commissioning automatic on/off operation street lighting system with 350 Wp (175 wpx2) solar module rating and energy efficient high power led lamps of 80 watts with luminous flux greater than 8000 Lummens and Lumen efficiency of 100 - 120 Luminarie - Luminaire with transparency lic cover , housing and high efficiency LED lamps and fitted with gasket and assessories for weather and insect proof operation Battery : 12 V 150 ah-02 nos sealed low/ negligible maintenance batteries designed for repeated cycle operation and shall be enclosed in a cabin that has pilfer proof lock & key arrangement. Pitch Circle dia 250 mm bolt length 750 mm , projected bolt length 125 mm . Pole foundation shall be pit of 75x75x200 cm in all type of soil or rocks and filling the pit with 1:2:4 cc and muffing of the pole up to 400 mm above the ground level.

Shifting of Utility Services as per direction of the Executive Engineer in consultation with the concerned department

Plantation: Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plant

ANIL DAS