Construction of Zila Parishad Bhawan Distt. Rewari

Amount

NS-1 Providing and fixing Stainless Steel Fittings (Chrome Finished) to doors, window, cupboard etc. (Grade 304) with nuts and screws etc complete.(as per sample approved by Engineer-in-charge) (i) Providing and Fixing 8` long Chrome finish S.S. Tower Bolt.

NS-1 Providing and fixing Stainless Steel Fittings (Chrome Finished) to doors, window, cupboard etc. (Grade 304) with nuts and screws etc complete.(as per sample approved by Engineer-in-charge) (ii) Providing and Fixing 6` long Chrome finish S.S. Tower Bolt.

NS-1 Providing and fixing Stainless Steel Fittings (Chrome Finished) to doors, window, cupboard etc. (Grade 304) with nuts and screws etc complete.(as per sample approved by Engineer-in-charge) (iii) Providing and Fixing 250 mm long Chrome finish S.S. Tower Bolt.

NS-1 Providing and fixing Stainless Steel Fittings (Chrome Finished) to doors, window, cupboard etc. (Grade 304) with nuts and screws etc complete.(as per sample approved by Engineer-in-charge) (iv) Providing and Fixing S.S REAR MAGNETIC DOOR STOPER.

NS-1 Providing and fixing Stainless Steel Fittings (Chrome Finished) to doors, window, cupboard etc. (Grade 304) with nuts and screws etc complete.(as per sample approved by Engineer-in-charge) (v) Providing and Fixing 150 mm floor S.S front Door stoppers

NS-3 Providing and Fixing Patch lock for frameless doors (Ozone make or equivalent)

NS-2 Providing and Fixing 450 mm long, 32 mm thick H type Stainless steel door handle for frame less doors (Ozone make or equivalent)

NS-4 Providing and fixing of 6 mm thick HPL (High Pressure Laminate) sheet cladding in horizontal or vertical direction on the building façade. The façade tiles shall be rigid and of adequate strength and shall satisfy all the performance parameters. The HPL sheet Cladding shall be fixed to an extruded aluminum support framework consisting of vertical aluminum tubular sections measuring 40x40mm spaced at maximum 1000mm c/c intervals, fixed to the wall using aluminum L-brackets spaced at maximum 1200mm distance vertically. (Aluminum frame will be payable separately)

F1: Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-`F` insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. 2280 lpm at 70 m Head

F2: Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump). Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminum sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 2280 lpm at 70 m Head

F3: Supplying, installation, testing and commissioning of electric driven pressurization pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump). Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-`F` insulation, conforming to IS : 325. M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 70 m Head

F5: Providing and fixing of pressure switch in M.S. pipe line including connection etc. as required.

F6.1: Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 250 mm dia (wall thickness 6.3 mm)

F6.2: Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 200 mm dia.

F6.3: Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia.

F6.4: Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia.

F6.5: Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm dia.

F6.6: Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 65 mm dia.

F6.7: Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 50 mm dia.

F6.8: Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 40 mm dia.

F6.9: Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 32 mm dia.

F6.10: Providing, laying, testing and commissioning of `C` class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25 mm dia.

F8: Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :SIngle Single headed Stainless steel

F9: Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :SIngle Single headed Stainless steel

F10.1: Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :50 mm Dia.

F10.2: Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :65 mm Dia.

F10.3: Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :80 mm Dia.

F10.4: Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :100 mm Dia.

F10.5: Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :150 mm Dia.

F10.6: Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :250 mm Dia.

F11.1: Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 65 mm dia.

F11.2: Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80 mm dia.

F11.3: Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dia.

F12: Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve and nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve and M.S. Pipe and socket.

F13: Supplying and fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

F14: Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

F15: Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

F16: Providing and fixing flow switch in following sizes M.S. pipe including connection etc as required: 150 mm Dia.

F17: Providing, fixing, testing and commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of following sizes as required : 100 mm Dia.

F18.1: Providing, fixing, testing and commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendant Type

F18.2: Providing, fixing, testing and commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Upright

F18.3: Providing, fixing, testing and commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Horizontal side wall Sprinkler

F19: Providing, installation, testing and commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

F20: Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange and landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

F21: Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 250 mm dia

F22: Supplying and fixing of Gunmetal Fire Brigade Suction Hose coupling (Draw out connection) with Nut for female coupling as per IS:902-1974 complete with 100mm dia G.I. Suction pipe and 100mm dia foot valve (to be connected to Static Tank).

F23: Providing and fixing Air vessel 450 mm dia 8mm thick MS sheet 1800mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25mm dia gunmetal wheel valves and the legs shall be provided MS plate size 75x75x5 mm at the bottom and grouted in CC foundation. with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

F24: Providing and fixing dial type pressure gauge with isolation cock and pipe at hydrant station and sprinkler line. Dia 100 mm calibration 0-15 Kg.

F25: Providing and fixing of hose cabinet of sizes 750 mm x 600 mm x 250 mm made of 2 mm thick MS sheet with 6 mm thick glazed glass doors i/c necessary locking arrangement suitable to accommodate external hydrant with butterfly valve 2 nos 15 mtr long hose pipe 1 no branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respective of external hydrant as required.

F26: Providing and fixing fully glazed MS fully welded construction double leaf door shutter for fire hydrant station fabricated from MS 50x50x6 mm angle iron frame, fixed to wall and hinged MS 40x40x5 mm angle iron door shutter with required MS sash bars for glazing complete with locking arrangements, enameled fire red finish with `FHC` written in front. The width and height to depend upon the actual size of the fire shaft available and get it approved by Engineer-in Charge/ consultant before fabrication

F27: S/F Fire man axe as rqd.

F28: Providing and fixing portable fire extinguisher, dry powder type (gas cartridge) with cylinder initially fully charged with dry powder (ABC type) of 4 Kg. Complete with standard discharge valve with tube, CI bracket for wall mounting etc. conforming to IS: 115683.

F29: Providing and fixing portable fire extinguisher carbon dioxide type with cylinder initially fully charged with CO2 gas of 4.5 Kg. Capacity, complete with discharge valve, discharge tube, horn, CI bracket for wall mounting etc. conforming to IS: 15683.

NS-5 120 MIN. FIRE RATING WOODEN FIRE CUM ACCOUSTIC DOOR (30-32 db) Supply of Wooden fire cum accoustic doors as per BS:476 Part- 20 and 22 and IS 3614 part-1 and part-2 for stability, integrity and thermal insulation. 03 Criteria Wooden door confirming to IS 277 with the following specification. Recommended 52mm thick fire door shall have doors tested at CBRI vide test report no. FR/0378 Dt: 22-06-2018 for maximum rating of 2hrs without acoustic properties, as there is no arrangement to measure the acoustic properties at CBRI, Roorkee. Any deviation in specification other than what is mentioned in the test certificates are not allowed. Proper label confirming the type of door and the hourly rating is mandatory. Door leaf shall be 77mm thick fully flush door with or without vision lite. 77mm thick shutter, comprising of 100mm x 69mm hardwood internal timber frame work, with infill of 45mm thick fire resistant and accoustic wool insulation of 48 Kg/m3 density coated with VIPER FR coating on both sides for insulation. The coated insulation shall be sandwiched between 12mm thick HILUX / PAMTECH Non Combustible (Calcium Silicate) Board on both sides (edge to edge on internal Hard wood frame and cladded with 6mm thick commercial ply and 1mm thick Laminate (Any Regular Plain Shade In Suede Finish) on both sides, with 77mm x 10mm exposed Hardwood beading, 20 x4mm fire and smoke intumescent seal shall be used for shutter and for the frame 01 Nos. X 20 x 4mm fire and smoke intumescent seal (For Smoke Sealing). The Frame shall be 140 x 90mm of Hardwood (Red Mirandi) and coated with VIPER Fire reatrdent Primer. The frame shall be installed in civil opening with the help of HRD fastener of size M10 dia of FISCHER Make. The rebate shall be of 20mm x 80mm in Door Frame to accommodate the shutter in frame The board shall be Resistant to vermin, mould growth, minor impact, abrasion and short term water attack and shall be Off –white in colour with a smooth surface suitable to receive most forms of decoration. The prices should be incluisve of SS Ball Bearing Hinges 100x89x3mm Of Becker F.S.,Overhead Door Closer TS-2000v Of GEZE, Mortise Dead Lock Of Becker F.S., SS H Type Pull Handle Of KICH / Becker F.S., SS Exposed Tower Bolt 450mm of DORSET. The door woulde fitted with accoutic seal set of RAVEN Make (RP8Si, RP16Si, RP-120) and will be having 11mm thick 120 min. fire rated interlayered glass vision panel of size 300x350mm of CONTRAFLAME DOORLITE of SAINTGOBAIN Make.

NS-6 Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical locations in load application areas that accommodates multi directional seismic movement without stress to it`s components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall conform to ASTM 6063). Floor Joint of 200mm gap

NS-7 Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings and complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall conform to ASTM 6063.) Wall Joint of 200 mm Gap

NS-8 Providing and fixing of expansion joint system of approved make and manufacture for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates as per ASTM B221-02. The system shall be such that it provides water tight roof to roof /roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.) Roof Joint of 200 mm GAP

NS-9 Providing and fixing of Flocked textile floor covering of FLOTEX HD Collection or equivalent with 100% Nylon and completely water proof resilient backing, The carpet should be manufactured under ISO 9001 and 14001, should have a built in anti-microbial treatment called SANITISED. The carpet should be completely stain resistant and of a density of 80 million fibres per Square Meter. The carpet should have permanent static control and should be fixed with with powder coated aluminium angles as per detail. Aluminium angles to be paid separately. [Makes FLOTEX (FORBO FLOORING, UK) / MOHWAK / SHAW (U.S.A.)]. The work should be carried out by the authorised installer of the Company in India.

NS-10 `Synthetic surface - 2.1 mm thick for Gymnasium Providing and fixing 100% pure polyvinyl chloride (PVC) wear layer combined with a pure PVC backing. Sanosol®, a fungistatic and bacteriostatic treatment shall be incorporated throughout the entire thickness. The wear surface shall be Triple-Action Protecsol®, UV cured, factory applied, and permanently bonded to the surface of the resilient Flooring. 1. Width of the roll . 4’11” (1.50m) 2. Total Thickness of the roll. 2.1 MM THICK 3. Weight 0.56 /sq.ft 4. Static Load Limit ASTM F970 modified (600 p.s.i. 5. Dynamic Load Limit (N) DIN V 18032-2 (April 2001) )1000 N 6. Excellent Chemical Resistance ASTM D543 7. Fungus Resistance ASTM G21 . Complete 8. Critical Radiant Flux ASTM E648 Class 1 9. Fire Rating ASTM/E648 )0.45 W/cm² Class 1 (Make Taraflex Gerflor / Tarkett / BSW)`

STP-1 Supplying, installing, testing and commissioning of Stainless Steel Perforated Screen (Grade SS-304) suitable for handling Raw Domestic Sewage

STP-2 Supplying, installing, testing and commissioning of raw sewage lift pumps as per following details: The pump set unit shall be complete with : a) Pumps: Non-clog fully floodable submersible pump suitable to handle raw sewage `Material of Construction (M.O.C): Corrosion Resistant in general Shaft — SS` Impeller — CI Motor: Housing — Stainless Steel RPM — 2900 Insulation Class — F Protection Degree — IP68 Suspension System Duty: Discharge : 2.5 M3/hr. (Minimum) Head : 12M

STP-3 Supplying, installing, testing and commissioning of filter feed pump as per the following details : The filter feed pump unit shall be complete with : a) Pumps: Vertical /Horizontal monoblock with mechanical seal `Material of Construction (M.O.C): Corrosion Resistant in general Pump Casing—Cast Iron/Stainless Steel` Impeller — CI Shaft — Stainless Steel Duty: Discharge ( each pump) : 5 M3/hr. Head : 30M

NS-4 Supplying, installing, testing and commissioning of twin lobe air blowers of approved Make `Details of Equipment offered (To be filled in by the tenderer)` Air Blower Make: Model: Discharge : 50 M3/hr. at 5000 mmWC

NS-5 Supplying, installing, testing and commissioning of FAB Reactor . It shall include media for bacterial growth, air diffusers (including for Equalization and sludge holding tanks), and all other equipment, media etc. required in the reactor unit. `Details of Media and Equipment offered (To be filled in by the tenderer)` Type of Reactor: No. of Reactor: Type of Media: Volume of Media/ Reactor (M3): Vol. of MS Tanks Required (each) M3: Kg BOD Removed/ M3 Media: Make:

NS-6 Supply, installation, testing and commissioning of non clogging type Sludge recirculation pumps CI material complete with mechanical seal and all accessories, motor of required capacity.Suction header with Isolation Butterly valves, Delivery header with isolation Butterly valve,NRV`s. Pumps shall have following duty. Sludge recirculation pump Flow Rate (each) = 2.0 m3 / hr Head = 8-10Mtr Solid handling = 8mm Make: Wilo/ Grundfos/Kirlosker Motor HP = As per manufacturer recommendation

NS-7 Providing, installing, testing and commissioning vertical down flow type multi grade sand bed pressure filter capable of filtering 5 cum/hour of water at prescribed filteration rate of 15 cum/sq.m/hr. The filter shall comprise of Composite FRP PP lined shell, suitable for a test pressure of 6 kg/sq.cm. , complete with pedestal, access cover, PVC underbed, 50 mm dia frontal piping, pressure guage, first charge of filter media. etc. Details of Filter `Filter Shell MOC : Fibre glass and polyester resin` Dia : 650 MM (Min.)

STP-8 Providing, installing, testing and commissioning vertical down flow activated carbon filter capable of filtering 5 cum/hour of water at prescribed filteration rate of 15 cum/sq.m/hr. The filter shall comprise of Composite FRP PP lined shell, suitable for a test pressure of 6 kg/sq.cm. , complete with pedestal, access cover, PVC underbed, 50 mm dia frontal piping, pressure guage, first charge of filter media. etc. Make : Astral or equal approved. Details of Filter `Filter Shell MOC : Fibre glass and polyester resin` Dia : 650 MM (Min.)

NS-9 Providing, installing, testing and commissioning chemical doser comprising 100 litres capacity HDPE tank, electronic metering pump of 0 - 6 litres/hr. capacity injection fitting, solution delivery tube etc. including making electrical connection for auto operation, all complete

NS-10 Providing, installing, testing and commissioning of Sludge Filter Press of following rating, all complete including making electrical and drain connections etc. Cake Holding Volume: 120 Litres Size: 450 mm X 450 MM with 17 nos. plates MOC: CI/ MS frame with Poly Proplene (PP) plates `Sludge Feed Pumps: a) Type : Screw Type b) Nos : 2 Nos.(1 Working plus 1 Standby) c) Duty : 2 Cum/Hr at 35 M Head

NS-11 Providing, installing, testing and commissioning UV Disinfection System for the complete disinfection of the final effluent of the following make or equal approved. a) Flow : 5M3/Hr Make: Alfa UV

NS-12 Providing, fixing, jointing, testing and commisioning interconnecting pipe work, sleeves, valves, Rotameters to control the flow, pressure gauges with isolating cocks etc.

NS-13 Providing, fixing, connecting, testing and commisioning of Pump Control Panel.

STP-14 Providing, fixing,connecting, testing and commisioning power and control cabling between pump panel, pumps, level controllers, solenoid valves etc.

NS-15 Providing, fixing, testing and commissioningof Electro Magnetic Flow Transmeter with Communication Port, of approved makes. Suitability: Sewage Effluent MOC: Body : Non-corrosive Lining : PTFE Flanges : Stainless Steel Electrode : Stainless Steel Coil Housing : Stainless Steel Pressure Rating : Minimum 10 Bar Temerature Withstanding : upto 850 C a) 50 mm dia

NS-16 Providing factory fabricated/ fabricated at site MS vessels for reactor-2nos, settler, sludge holding tank and chlorine contact tank, complete wirth all accessories, overflow channels, support structures, ladders, inspection platforms etc.all complete including installation at site. Note: The material of construction shall be non corrosive and the Vendor shall submit a note mentioning the material , proposed anti corrisive treatment and method of fabrication.

STP-18 ULTRA FILTERATION (UF) BASED POLISHING SYSTEM Providing, installing, testing and commissioning of Ultra Filteration (UF) system for further polishing treated effluent and capable of producing 5,000 litre / hour of polished water meeting the requirements given in Section-B and D of Scope of Work. The system shall be complete with UF Feed Pumps (1W plus 1S), CIP Pumps (1W plus 1S), Backwash Pumps (1W plus 1S), Cartridge Filters, UF Membranes Flushing / Cleaning System, complete instrumentation for automation and monitoring, Rotameters, Pressure Gauges, interconnecting pipework, electrical cabling and switchgear, all complete as described in Scope of Work enclosed herewith.

NS-11 `External Wall Finishes Providing and Applying permanent stone finish wall covering system made of pure quartz, inorganic pigments, pure acrylic emulsions, binder of 100% pure acrylic emulsion, broad spectrum fungicides to be sprayed to the surface by means of a customized spray gun with a coating thickness of 1.5-2.0mm over coated with a clear acrylic top coat in 2 coats, to be applied on a cured, smooth and level plaster base without keying covered with a two coat wall care putty as per manufactures application products, as per shade combination approved by Architects all complete inclusive of primer on the base, for all height, inclusive of scaffolding and creation of groves it approves. Approved manufactures 1. Bakelite hylam 2. Unitile 3. Any other approved by architects `

NS - HO101 Providing uPVC pipes confirming to relevant IS 4985-2000 including all fittings with or without access doors i.e bends, junctions, cowls, offsets, etc., and jointing with Solvent cement as per Manufacturer`s specifications including cutting holes in walls and floors, wherever required, and making good the same complete as directed by the Project-in-Charge. (i)PVC Pipe 75mm X 6 kg/cm2

NS - HO102 Providing uPVC pipes confirming to relevant IS 4985-2000 including all fittings with or without access doors i.e bends, junctions, cowls, offsets, etc., and jointing with Solvent cement as per Manufacturer`s specifications including cutting holes in walls and floors, wherever required, and making good the same complete as directed by the Project-in-Charge. (ii)PVC Pipe 63mm X 6kg/cm2

NS - HO104 Providing uPVC pipes confirming to relevant IS 4985-2000 including all fittings with or without access doors i.e bends, junctions, cowls, offsets, etc., and jointing with Solvent cement as per Manufacturer`s specifications including cutting holes in walls and floors, wherever required, and making good the same complete as directed by the Project-in-Charge. (ii)PVC Pipe 40mm X 6kg/cm2

NS - HO103 Providing uPVC pipes confirming to relevant IS 4985-2000 including all fittings with or without access doors i.e bends, junctions, cowls, offsets, etc., and jointing with Solvent cement as per Manufacturer`s specifications including cutting holes in walls and floors, wherever required, and making good the same complete as directed by the Project-in-Charge. (ii)PVC Pipe 50mm X 6kg/cm2

NS - HO202 Providing of Spray Pop up having radius of covering 3 m- 5 m with discharge of 0.08 lps to 0.1 lps and operating pressure from 2.5 kg/cm2 to 3.0 kg/cm2. The Spray Head body shall be constructed of heavy-duty, ultraviolet resistant plastic and stainless steel spring with mutifunctional wiper seal with small exposed cover. etc. item complete.

NS - HO203 Providing of 3/4` Pop up Connecting Four Elbow Swing joint Assembly. The fittings shall be made of UV resistant thermo plastic.etc. item complete.

NS - HO204 Providing of 1/2` Pop up Connecting Four Elbow Swing joint Assembly. The fittings shall be made of UV resistant thermo-plastic.etc. item complete.

NS - HO201 Providing of Impact Pop up having radius of covering 8 m- 12 m with discharge of 0.15 lps to 0.2 lps and operating pressure from 2.5 kg/cm2 to 3.0 kg/cm2. body shall be constructed of heavy-duty, ultraviolet resistant plastic and stainless steel spring with multifunctional wiper seal with small exposed cover. etc. item complete.

NS - HO205 Providing of PVC service saddle of varying size 3/4` and 1/2` etc. item complete.

NS - HO301 LLDPE Emitting Pipe 16mm, CL-2 Pressure Compensating

NS - HO302 LLDPE Lateral Pipe 16mm 2.5kg

NS - HO401 Providing of Main Line PVC Double Union Ball Valve,security pivot to maintain lever in space,double water tight joint,direct injection stem,Stem O-Ring, non mechanical ,ball Seals with backing seals and with a base which permits maximum penetration into the valve of size 63mm. with pressure rating PN 10

NS - HO402 Providing of 10` Round Valve Box with green lid and corrugated structure with unique shovel access slot and bolt hole knock out etc. item complete

NS -HO403 Providing of flush valve 50/40 mm size with all fittings and accessories complete

NS - HO404 Providing of PVC Gate Valve 75mm with Maximum Working Pressure 10kg/cm2 as Control valves as per specifications including the cost of all fittings and accessories complete

NS - HO405 Providing of PVC Quick coupling valve 1` made of plastic with locking cover corrosion resistant and stainless steel spring. Including service saddle and riser assembly. etc. item complete.

NS - HO406 Providing of Plastic Key threads into top of QCV to provide water access And Brass Swivel Elbow. etc. item complete.

NS- HO407 Providing of 6`Round box with green lid and corrugated structure with unique shovel access slot and bolt hole knockout. etc. item complete.

NS - HO408 Providing of a double acting 2` Air release valve, The Air release valve shall be capable of both releasing and admitting air from and into the line. Including gate valve, service saddle, and riser assembly

NS - HO501 SAND MEDIA FILTER 40 M3/HR WITH BACK WASH ARRANGMENT

NS - HO502 DISCK FILTER 25 M3/HR WITH FLUSH VALVE

NS - HO503 Providing of Pressure Relief Valve with Maximum operating pressure 10kg/cm2 made of plastic and 1.5` in size

NS - HO601 Supplying of Mono Block Pump (1 W plus 1S) having 6.5 Lps Discharge @ 45- 50 Mtr head, with suction delivery, NRV ,with control panel complete

NS - HO602 Installation Charge

NS - HO303 Pressure compensating dripper 2, 4 and 8 LPH

Bidder Name

Amount

Gawar Construction Limited(GSTN-06AADCG1026A1ZH)

M/s. Lord Shiva Construction Company Pvt. Ltd(GSTN-06AAACL2040G1Z3)

Ashok Kumar Garg(GSTN-06ABTPG1118P1ZC)

Deepak Kumar Contractor(GSTN-06AKPPG6396J1ZJ)

Krishna Construction Co(GSTN-06AALFK6441Q1ZP)

Prerna Real Tech Pvt. Ltd.(GSTN-NA)

Prerna Real Tech Pvt. Ltd.

Gawar Construction Limited

Ashok Kumar Garg

M/s. Lord Shiva Construction Company Pvt. Ltd

Krishna Construction Co

Gawar Construction Limited

Deepak Kumar Contractor

Prerna Real Tech Pvt. Ltd.

M/s. Lord Shiva Construction Company Pvt. Ltd

Krishna Construction Co