PROVN OF PATHWAY, SPL REPAIR TO OTM ACCN BLDG No. NP-6, PROVN OF SOAKWELL CUM SEPTIC TANK, AND PROVN OF 50 NOS WIREMESH DOOR IN AOR OF AGE BR-II IN DIFFERENT LOCATIONS UNDER GE(WEST)PATHANKOT

Amount

Sch 'A' Part-I B/R Portion:- Surface excavation not exceeding 30 cm deep and average 15cm deep and getting out in soft / loose soil, complete all as specified.

M&L for broken stone or boulders in hardcore of gauge exc 63 mm but n exc 100 mm deposited spread and levelled in layers n. exc 15 cm thick watered and rolled/rammed to a true surface complete all as specified and as directed.

M&L for plain Cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate), 75mm thick as in sub base complete all as specified and as directed.

M&L for 60mm thick glossy finish factory made chamfered edge cement concrete rubber moulded paver block of M-35 grade with approved colour, design & pattern with pigment as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as secified and as directed. Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other, Colour of paver blocks & laying pattern approved by GE.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft & loose soil complete all as specified and directed by Engr-in-Charge.

Returning, Filling in, including spreading, levelling, watering and well ramming in layers, not exc 25 cm in soft/loose soil complete all as specified and directed.

Removing excavated material n exc 50 m and depositing where directed at level n exc 1.5m above the starting point complete all as specified and directed.

M&L for cement concrete type B-1 (1:2:4) using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed etc complete all as specified and directed.

Taking down chowkatts or frames (without taking off shutters from frame)exc 1.5 sq. m but n exc 4 sq m each complete all as specified and directed .

Taking down of chowkats or frame with shutters (without taking off shutters from the frames) n.exc 1.50 Sqm each complete all as specified and directed .

M&L for Pressed steel frames of size 165mmx60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. including back filling of hollow portion of frame including fixing of hold fast with plain cement concrete type c-0, 1:3:6 using 12.5mm graded crushed stone aggregate, complete, as specified.

S&F 35mm thick flush shutter, solid core construction, with particle board core with block board core and plywood face panels commercial type on both side complete all as specified and directed.

M&L for factory made Glazed and skelton shutters 35mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (without shash bars), size of members of shutters as specified in SSR Part-1, secton 8, clause 8.24(a) kiln seasoned and pressure treated, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified and directed.

M&L for Preparation of new steel surface of any descripion over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed..

M&L for preparation of old painted steel surface of any description over 10cm in width or grith not otherwise described for and apply one coat of synthetic enamel paint, complete all as specified and directed.

S&F solid PVC door frame of size 50 x 47mm made out of 5mm wallnut colour PVC sheet reinforced with MS square tube suppling fixing in opening as per specification & drawing complete all as specified & directed.

S&F factory made solid panel PVC door shutter of walnut colour, 28 to 30mm thick (stile) with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on front side face and 2mm plain colour pvc sheet on back face at site as per specification & drawing, complete all as specified & directed.

S&F Aluminium, anodised, barrel tower bolts of 200 mm long and 10mm dia stove enamelled black with bright bolt fixed complete all as specified and directed.

S&F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified.

S&F 150 mm Aluminium handles, cast type, anodised fixed complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor Overall length of cover plate 140mm complete all as specified and directed.

S&F stainless steel hinges, 100 mm long of medium weight, fixed with screws, complete all as specified & directed.

S&F MS butt hinge 100mm long, heavy weight cold rolled fixing with welding to door frame.

S&F 200mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate including welding to steel frames complete all as specified & directed.

S&F steel window/ventilator factory made, made out of mild steel box type and shutter suitable for double shutter i.e. glazed and gauged shutter. Glazed shutter made out of hollow section with sash bar and gauged shutter made out of hollow section without sash bar including hinges, tower bolt, handle, grill 10mm sq bar including two coat of synthetic enamel paint over one coat of red oxide primer, atrred hold fasts, PCC bed blocks for fixing hold fast, including plain/ figured glass and stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.18mm & fixed with stainless steel wire staples etc complete all as per drg No CEPZ/ C-TD/032/13 Sheet No 1/2 & 2/2 including taking down old windows/ventilators, complete all as specified and directed.

M&L for Preparation of new wooden surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar or cement lime mortar including all quions, wall, arches, pillars, man-holes, drain etc complete all as specified and directed.

M&L for brick work with fly ash old size brick, straight or curved on plan exc 6.0 m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with fly ash old size brick, straight or curved on plan exc 6.0 m mean radius built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc including necessary scaffolding up to four storeys height of bldgs if required and removing of debris out of MoD land complete all as specified and as directed.

M&L for rendering 15mm thick in CM 1:4 in two layers with backing coat 10mm thick and second coat of 5mm thick WPC (as per manufacturer’s instructions) on fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement including necessary scaffolding up to four storeys height of bldgs if required complete all as specified and as directed.(Note:- WPC shall be measured and paid separately)

Supply only `Liquid Water Proofing Compound complete all as specified and as directed .

M&L for rendering 10 mm thick on other than fair face of brickwork or concrete wall surfaces in cement mortar 1:6 and finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for rendering 15 mm thick on other than fair face of brickwork or concrete wall surfaces in cement mortar 1:6 and finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for rendering 5mm thick on fair faces of brickwork or concrete surfaces in cement mortar 1:3 as on ceiling complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of cement base paint over a coat of alkali resistant priming, of any approved colour including necessary scaffolding if required, all painted areas site to be cleaned and hand over as earlier without any extra cost, complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash on walls, complete all as specified & directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash without any brush marks on the surface including necessary scaffolding if required complete all as specified and as directed.

M&L for preparation of newly plastered internally surfaces of wall and applying one coat of wall care putty on the surfaces & making the surface absolutely smooth surface and applying one coat of primer (as per manufacturer’s recommendations) on the surfaces and applying two coats of distemper oil emulsion, white or tinted, finished without any brush marks on the surface including necessary scaffolding up to four storeys height of bldgs if required, all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed. Note:- Shade/colour shall be approved by GE.

Demolition of cement concrete (unreinforced) in ground floor and pavings n exc 15 cm thick ( above or below GL) and disposal of debris out of MoD land, complete all as specified

M&L for cement concrete type C-1 1:3:6 (using 20mm graded crushed stone agg) as in plinth protection and paving 75mm thick laid in slope finished even and fair without using extra cement incl making joints every 2.5m and complete all as specified.

M&L for repairing to chajjas, roof projection and facias of exposed reinforcement surface or damaged loose RCC surface including cutting down rusted/exposed reinforcement and applying one coat of cement slurry and filling with cement concrete 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) and finished with cement mortar 1:3 using coarse sand. Thickness of RCC member not exc 150 mm including scaffolding if required, complete all as specified and as directed . Note : No extra rates of scafffolding will be paid separately against this item.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed .

M&L for coloured Glazed ceramic tiles in vertical surface such as dado etc 450mmX 300mmX 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and as directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

S&F joint free non skid coloured Ceramic tiles 08mm to 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

S&F joint free non skid coloured Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for non-skid ceramic coloured tiles, area of each tile exceeding 0.18 square metre but not exceeding 0.38 square metre of 7 to 8 mm thick set and jointed in neat cement slurry and pointing in coloured cement to match shade as in skirting/dado including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M&L for obliterating the old writing of any description, not exceeding 0.1 square meter, with paint to match with the existing work including necessary scaffolding if required, Shade/colour shall be approved by GE,all painted areas site to be cleaned and hand over as earlier without any extra cost to Govt complete all as specified and as directed.

M&L for Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for precast reinforcement cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate, in cover slabs( for manholes etc.) chulla hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar (1:6) complete all as specified and directed. (Reinforcement shall be measured and paid separately).

M&L for Mild steel TMT bar 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L liquid water proofing treatment to RCC roof slab including dismantling of existing roof treatment of any description such as worn-out tar felt, debris, mortar of any description & any thickness, surface cleaning of all foreign material such as shrubs/roots, fungus, moss, dust including plaster, APP membrane etc. including disposal of debris out of MoD land, in following procedure : (a) Prepare the surface by cleaning with concrete surface grinder/ wire brush and a high pressure water jet and ensure that it is free of dust, oil and loose particles. Damaged portions, hollow area must be repaired with epoxy mortar and repair cracks of old concrete by cutting 'V' groove, corners and joints of drain pipes, channels etc. treated with epoxy mortar prepared with epoxy primer (as per manufacturer's instructions). (b) Laying 10mm thick rendering in Cement mortar 1:3 with liquid water proofing compound (as per manufacturer’s instructions) on fair faces of concrete roof surfaces, finished even and fair to receive treatment on roof Complete (c ) Applying three coats of polyurea waterproofing coating as per manufacturer's instructions for maintaining minimum dry film thickness 1.5mm and elongation at break of free film of approx. 500% ± 50% and tensile strength at 14 days of 5MPa. (e)The materials shall be applied with brush or roller, complete in all respect as per the direction of Engineer-in-charge / Consultant. (Note:- minimum 6hrs interval between two coat shall be maintained) (f) All auxiliary and accessories involved during application should be supplied by single manufacturer as a part of system. Note: - (i) Work to be carried out by authorized applicator and as per manufacturer’s instructions. (ii) Providing test with filling of water for continuous 48 hours if there is any leakage than entire treatment will be done again by contractor without any cost. (iii) The rate includes for filling cracks in existing roof with epoxy cement mortar using suitable bonding agent before laying cement plaster.

S&F Rotational moulded polyethlene water storage tanks three layers of 500 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

S&F in repair Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed.

S&F 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed.

Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed.

S&F 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed.

Cutting chase, pining in making good to facings where required and pointing in cement mortar (1:3) to ends, cutting chases for concealed water tubing ror concealed conduit wiring etc and making good cutting not exc 10cm girth.

S&F in repair 15 mm bore long body CP Bib taps cast copper alloy fancy type with capstan heads (chromium plated),and cup screwed down , high pressure for iron pipe complete all as spd & directed.

S&F in repair CP stop cock/angle valve cast copper alloy screwed down high pressure ,with crutch or butterfly handle screwed both ends for iron pipe or for union of 15 mm bore complete all as specified & directed.

S&F in repair stop valves, 15mm dia, cast copper alloy,chromium plated fancy type with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed

S&F in repair pillar taps, fancy type cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore, complete all as specified & directed.

S&F in repairs Brass CP shower rose 125mm size including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs corner sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S&F in repair 15mm dia 600 mm long PVC connection including brass check nut at both ends screwed both end for iron pipes complete all as specified and directed

S&F in repairs Tubular towel rail, ISI marked 60cm long between flanges , 20mm dia 'D' type Brass Chromium plated incl brackets, fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. complete, including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed.

S&F in repair viterous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, witht integral foot rests (excluding flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc. complete including making good to floor complete all as specified and as directed.

S&F in repairs of Wash basins, Vitreous China (flat back type) 550 x 400mm, including cutting for and pinning in ends of brackets or erecting stand, including 32 mm dia 75 cm long PVC flexible waste pipe etc complete all as specified and as directed.

S&F in repairs for Viterous China urinal, half stall type, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed.

S&F in repair Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms)

S&F 32mm bore PVC waste pipe flexible including PVC waste coupling with minimum length 800mm, Make : Paryag or equivalent in any of the make mentioned in list of product.

S&F Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern

S&F in repairs 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specfied and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and as directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F PVC (SWR) bends any radius 110mm dia all as specified and directed.

S&F in repairs of PVC (SWR) 110mm bore vent cowl complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, PVC/AC or Reinforced concrete) set in cement mortar,and taking out of trenches, if required, Internal dia of pipe in 75mm/100mm complete all as specified and directed

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and directed.

S&F PVC (SWR) bends any radius 75mm dia all as specified and directed.

S&F in repairs 75mm PVC floor trap, ISI marked with CP grating with/without waste pipe hole incl jointing to waste pipe fixed with solvent cement complete all as specified and as directed.

S&F in repairs of PVC (SWR) 75mm bore 'T' equal or unequal complete all as specified and directed.

S& F in repairs fancy type MS curtain rods powder coated 25 mm dia with end fittings and fixing brackets of required size (two nos end brackets with fancy type stainless steel finial and two Nos wall brackets fixed with wooden gutties and screws, complete all as specified and as dircted.

M&L for Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors, gate ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified.

M&L for 150mm bore Reinforced concrete pipes, class NP-3(ISI Marked), laid and jointed in trenches complete with collars complete all as specified and as directed.

M&L for Concrete bed to drain pipe 200mm bore, type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) including packing under, and haunching against the sides of pipes after they are laid and tested;complete all as specified and as directed.

M&L for Plain Cement Concrete Type C-2, 1:3:6 (using 40 mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in surface channels, drais etc complete all as specified and as directed.

M&L for 20 user LLDPE septic tank designed to carry sewage and sluge water including earth work and PCC foundation 1:4:8 of appropriate size, vent shaft, and connection complete all as specified and directed by Engr-in-Charge

M&L for construction of soakage well of size 1.8mx3mdeep, including earth work in any type of soil, PCC foundation 1:3:6, old size burnt clay brick work for honey combed masonry in cement mortar 1:4 with top ring of M-25 concrete, including intercepting chamber and screen chambermade of brick masonary in CM 1:4, M-25 RCC cover slab, interlocking pipes of RCC/DWC complete all as specified and as directed by Engg-in-Charge.

M&L for preparation of newly plastered external surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over and including 1.5mm thick wall care putty without any brush mark on the surface including necessary scaffolding complete all as specified and as directed.

Cutting holes in brick wall built in cement mortar or cement lime mortar for inserting holdfast/purlin/rafter etc and making good dismantal portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required, depth of embedded portion of holdfast or lugs measured from the face of the jamb into the wall exc half brick but n.exc one brick complete all as specified and as directed.

M&L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each and removing from site complete all as specified and directed.

Sch 'A' Part-I E/M Portion:- Taking down old unserviceable copper/aluminium point wiring (light, fan, socket , power socket and bulk head fittings) on surface wiring on wooden batten/casings & caping complete, including fixture and fittings such as switches, ceiling roses,pendents holder, regulators and sockets by unscrewing carefully from boards etc and making good disturbed surfaces of walls, as per existing finishes complete all as spd and directed.

M&L for point wiring for one light/one fan controlled by one switch with 1.5 Sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H 1100 volte grade cable, with and including PVC rigid concealed conduit (ISI marked) with all fittings including sheet steel/CI terminal box of adequate size including 1.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable as earth continuity conductor connected to comman earth dolly, complete all as specified and directed. Note:- 1. connection of cable with MCBs/switch sockets shall be done through proper size copper /brass thimbles. 2. Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible. 3. Proper colour coud will be used for wiring as per the electrical rule and as directed.

All as per Srl item No 101 here-in-before but for 5 pin 5 amps socket outlet on the independent board controlled by one switch SP, one way 5 Amp, 240 Volts. complete all as specified and directed.

All as per Srl item No 101 here-in-before but for 5 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed.

M&L for point wiring with 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable with in and including PVC concealed conduit heavy duty with all fittings including anodise pressed steel sunken box with bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed.

M&L for point wiring with 4 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable with in and including PVC concealed conduit heavy duty with all fittings including anodise pressed steel sunken box with bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 4 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed.

S&F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S&F switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 amps flush type 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S&F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

S&F ceiling rose 65 x 50mm three terminals complete all as specified and directed.

S&F ceiling fan regulator electronic socket type 5 stage speed variation ISI marked complete all as specified and directed.

S&F CFLs with LED Lamp, B22 type ,12 watt,complete all as specified and directed.

S&F in replacement energy saving decorative 20W LED tube light box type, light fitting extruded PVC housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver complete with all accessories prewired without tube and making connection with twisted flexible copper cable of suitable size from ceiling rose/PVC connector to light fitting complete all as specified and as directed.

Taking down carefully ceiling fan from the hook including dismantling the blades and minor repair such as replacement of locking pin, reel insulators, bolts, nuts etc and painting one coat of synthetic enamel paint of existing colour including rehanging the same at existing position after cleaning, greasing and connecting up with PVC insulated copper flexible wire of suitable size from ceiling rose to connector of fan complete all as specified and directed by Engr-in-Charge .

M&L for providing/ cutting the round/ square hole of required size in wall finishing the distrubed surfaces as per existing finishes complete all as spd and S&Fing propeller MS ventilating fans, Single phase, 230 volts 300 mm or 12" sweep complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core of suitable size copper cable from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as spd and directed by Engr-in-charge.

S&F in replacement of old unsv sheet metal enclosures distribution boards, double door three phase 415 volts 4 ways vertical TPN DB for comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following (a)MCCB FOUR POLE 63 Amps AC 415 VOLTS 25 KA=01 NO as incoming and 12 nos. MCB SP 40 Amps, C series as outgoing (Note :- (i) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(ii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped.(iii) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (iv) double continuous earth wire shall be provided for each three phase DB from earthing mains dolly (v)MCCB's and MCB's should have a same make as of DB.

S&F in repair bldg secuirty light fitting energy saving high efficiency LED street light fitting 35 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 25 mm dia bent to shape having length not less than 0.9 mtr fixing with clamp etc and making connections using suitable size copper cable from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage.

Supply, laying and testing in replacement LT XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 25 sq. mm 4 core complete all as specified

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft/loose soil for laying of cable ,pole foundation,stay,laying of pipe etc complete all as specified and directed.

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable complete all as specified (Note:-Punned thickness shall be measured and paid)

M&L for brick covering equal to length of bricks as mechanical protection to cable with well burnet sub class ‘B’ bricks laid as directed by the Engr-in-Charge.

S&F GI tubing light grade 80 mm bore for cable protection laid in trenches in road crossing or fixed to wall/Pole including fittings /clamp complete all as specified and directed.

Supply and installation of the electric water storage heater of ABS body type, 25 ltr capacity with rated power 2KW, 5 star rated, vertical type, thermally insulated mild steel tank with glass line coating inside the tank alongwith glass lined incoloy heating element with anti corrosive magnesium anode, NRV, thermostat, indicators and temperature adjustable knob including steel braided flexible connection for pipe of size 15mm bore with GI hexagonal adopters/nuts on both sides for inlet (cold water supply) & outlet (hot water supply) and including provision of wall mounting arrangements and mounting on wall with suitable size of anchor bolts with complete connection of water including testing after installation complete all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode , 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level)with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point , GI tubing 15 mm bore light grade protection pipe , GI watering pipe 20mm bore light grade with funnel and wire mesh , charcoal ,salt packed around the earth plate and precast PCC 1:2:4 (Nominal mix ) reinforced with XPM having weight not less than 4 kg /sqm including suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover including earth work in any type of soil , removal of surplus soil to a distance n.exc 50m and connecting , testing on completion complete all as shown on electric plate No 03 of SSR -2009 Part I and connecting to existing earth test point complete all as specified and directed or including testing on completion.(Note: Excavation and earth work is deemed to be included in the rates quoted).

Note:-The accepted amount will be arrived after deducting the Sch of credit i.e. Rs 18,430.00 and any other reduction if any from quoted amount.

BALKRISHAN GUPTA AND SONS (BID ID -3442654)

M/S SATYA SAI CONSTRUCTION (BID ID -3436840)

HARI OM ENTERPRISES (BID ID -3435437)

JP AND CO. (BID ID -3436768)

Substantial Const. Co. (BID ID -3437072)