PROVN OF COMMERCIAL INTEGRATION SUPPLY FOR MFCR AT AF STN ISSAPUR C/O AF STATION RAJOKRI UNDER GE (AF) GURGAON

M & L Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil. Complete all specified and directed by Engr-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/Disintegrtated rock complete all as specified.

Removing excavated material to distance not exc 50 metre and depositing where directed at a level n.exc 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-Charge

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified.

M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete, sub base complete all as specified.

M&L for providing reinforced cement concrete (nominal mix) type B1 (1:2:4) using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.

Use and removal of steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits [if any] of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces complete all as specified and as directed.

M&L for providing reinforced cement concrete (nominal mix) type B1 (1:2:4) using 20 mm graded stone aggregates as in Columns, pillars, piers, posts and struts complete all as specified.

Use and removal of steel formwork to sides of pillars, posts, struts, piers, columns and stanchions of any shape / cross section for rough finished surfaces of concrete complete all as specified and as directed.

M&L for providing reinforced cement concrete (nominal mix) type B1 1:2:4 (20 mm graded stone aggregates) as in beams, cantilever, lintels over 1.5m span etc complete all as specified and directed.

Use and removal of steel formwork to sides and soffits of floor or roof beams, beam launchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, splays between floors and beams and similar works for rough finished surfaces of concrete complete all as specified and as directed.

M&L for providing reinforced cement concrete (nominal mix) type B1 (1:2:4) using 20 mm graded stone aggregates as in slabs supported on walls,beams and columns in floors,roofs, complete all as specified.

Use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including rough finished surfaces complete all as specified and directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 6 mm to 8 mm, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M & L modular bricks in cement mortar 1:4 with Brickwork with flyash bricks, straight or curved on plan to any radius i n half brick thick walls,built in etc complete all as spd and directed.

M & L for Preparing the surfaces of concrete roof and brushing neat cement slurry with 3.0 KG of cement per Sq.m area, rendering 10mm thick in cement mortar 1:3 on concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make as per manufacturers instructions for levelling the surface smooth to receive the water proofing membrane, priming the surface with a coat of cold applied bituminous primer @ 0.50 KG per Sq.m, applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m, laying Polymeric water proofing membrane of weight not less than 3.00 Kg per Sq.m reinforced with polyester non-woven fabric of weight not less than 150 Grams per Sq.m, by torch application with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusion including applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m and finished with a coat of bituminous aluminium paint @ 100 grams per Sq.m on top for water proofing treatment complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M&L for rendering 15 mm thick in cement mortar (1:6) on brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified.

M & L for rendering 5mm thick in cement mortar 1:4 including mixing water proofing compound as per manufacurers instructions over a backing coat of 10mm thick in CM 1:4 on concrete or brick masonry surfaces and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

Supply only integral water proofing compound of approved make

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling finished even and smooth without using extra cement complete all as specified and as directed.

M&L Preparing of new surface of wall and applying two coats of Cement base paint over a coat of alkali resistent primer.Complete all as specified and directed

M & L for preparing newly plastered ceiling surfaces and applying three coats of white washing complete all as specified and as directed.

M & L preparation of newly plastered surfaces of wall and applying two coats of OBD over a coat of primer including preparation of surfaces on walls as specified and directed .

Providing and laying kadappa stone slab flooring, 600 x 600 mm size , 25 to 40mm thick, machine cut and mirror polished, over 20mm thick machine cut and mirror polished,over 20mm thick cement mortar (1:4) , jointed with grey cement slurry mixed with pigment to match the shade of stone including rubbing and polishing complete.

Providing and laying kadappa stone slab flooring in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade including backing coat 10mm thick in CM 1:4 .

M & L for 75 mm thick, PCC 1:3:6, Type C-1, using 20mm graded stone aggregate as in plinth protection, surfaces finished even and smooth complete all as specified and as directed.

M & L for Hardcore of gauge not exceeding 63mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rolled/rammed to a true surface complete all as specified.

M & L for 100 mm thick, PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in sub floor, floor ect, surfaces finished even and smooth complete all as specified and as directed.

M & L for 100 mm thick, PCC 1:2:4, Type B-2, using 40mm graded stone aggregate as in sub floor, floor ect, surfaces finished even and smooth complete all as specified and as directed.

S & F 100 mm size, Butt hinges, Stainless Steel, Medium weight, bright polished including fixtures complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 125 mm long complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 150 mm size of extruded section complete all as specified and as directed.

Supply only 4.00 mm thick Sheet Glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc and applying a shop coat of red oxide primer including providing PCC 1:3 :6 type C-0 using 12.5 mm graded crush stone aggregate for filling back of chowkhats complete all as specified and as directed by the Engineer-in-Charge

S & F Factory made, 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F window or ventilators section of frame 72x55mm fixed to wall or concrete surface with rowl plugs made of galvanised steel powder coated and section of shutter 47x20mm mulion section 72x50mm (Based steel as per IS 513 "D" quality galanised as per IS 277 with zinc of 120 gms/sqm) glazed or gauged and wire gauge shutter prepare to receive wire mesh to the shutter (Double door shutter) with total coated thickness of 0.6mm including grills/guard bars made of square bars powder coated fixed to window frame with screws including necessary fittings and all builders hardware such as handles, tower bolts and stays etc complete all as specified and as directed. Make : NCL type-4000 Series (Note : Glass and wiremesh shall be measured and paid separately under respective items)

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 250 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 300 mm size of extruded section complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F Floor Door Stopper of size 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

M & L for preparation of new undecorated painted wooden surface of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic Enamel paint over one coat of pink primer complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for providing pre construction anti termite treatment for the backfill in contact with foundation by applying emulsion at the rate of 7.5 litres per square metre of vertical surface [Area of the substructure in contact with back fill] complete all as specified and as directed.

M & L for providing pre construction anti termite treatment for the top surface of filled earth by applying emulsion at the rate of 5 litres per square metre of surface complete all as specified and as directed.

M & L for providing pre construction anti termite treatment for the soil under plinth protection by applying emulsion at the rate of 5 litres per square metre of surface area complete all as specified and as directed.

M & L for providing pre construction anti termite treatment for the soil along with external perimeter of building by applying emulsion at the rate of 2.25 litres per running metre of the perimeter wall complete all as specified and as directed.

S & F Galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tacks or galvanised wire staple.

S & F 35 mm, 2nd class hard wood factory made, Glazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a);,etc complete all as spd and directed.

M & L Pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc and applying a shop coat of red oxide primer including providing PCC 1:3 :6 type C-0 using 12.5 mm graded crush stone aggregate for filling back of chowkhats complete all as specified and as directed by the Engineer-in-Charge

M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:4) for bedding of tiles complete all as specified.

M&L for Cement concrete tiles 25cm x 25cm x 22 mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished, set with grey cement and pigments over 15mm thick cement screed bed in cement mortar 1:4 complete all as specified and directed.

S& F for machine pressed precast concrete interlocking paver block any shape and size,with grey cement and pigment to match, confirming to IS 15658-2006 of 60mm thick M-35 grade laid over 50 mm thick sand cushioning.

Providing and laying rubber flooring / matting 3mm thick of approved shade and pattern including adhesive and fixing as per manufacturer's instruction over existing smooth cement floor. Complete all as specified and as directed.

Supply,laying, connecting and testing Single core PVC insulated multistranded 1100 volt grade copper conductor cable of size 185 sqmm single runs drawn through existing pipes/ Floor/trench/wall complete all as specified and directed.

Supply and fixing MCCB 400 Amps 4 pole,415 Volt, 36 KA including under voltage/over voltage relay with adjutable thermal setting (80% - 100%) all as specified and directed.

Supply and fix ON load changeover switch 400 amps, 4 pole 415 volt 50 Hz,with front handle in SS Enclosure and Conforming to IS/IEC : 60947-1 & 3 of complete all as directed .

M& L for earth continuity conducted or main earthing lead fixed to wall/ceiling on batten or recess or chases or buried in ground or drawn in conduit/pipe or other directed situation for earthing etc as required 20x3 copper strip all as specified and directed.

Supply and fixing Copper cable lugs suitable for 185 Sqmm copper cable complete all as specified and directed.

M&L for carrying out horizontal boring below roads/PCC hard sanding/Drains all as specified as directed for inserting GI pipe of 150 mm dia with a depth upto 1.5m & length of road upto 6 m of the suitable for 150 mm dia GI pipe

Supply and fixing of GI tubing, light grade,150 mm bore with all fitting lais in trenches / pole / wall for protection of cables in repairs complete.

Supply , laying & testing XLPE insulated, armoured, heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches, sleeving through pipes or fixed on poles & walls or laid under floors including jointing with suitable size aluminium lugs complete of size 16 Sqmm nominal cross section x 2 core complete all as specified and directed

Supplying and laying synthetic Rubber insulated mats 10 mm thick for voltage upto 11 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety of sizes 2m x 1m.all as specified and directed by Engr -in- Charge.

M&L for point wiring complete with stranded copper conductor 1.5 sqmm single core (nominal area ) PVC insulated and unsheathed cable 1100 volts grade drawn in and including medium duty concealed in PVC concealed conduit conforming to IS and ISI marked not less than 19 mm dia with 1.6mm thick concealed pressed steel terminal boxes with plate and framecover for rquired module including single core stranded copper conductor 1.5 sqmm PVC insulated unsheathed cable in same conduit as earth wire to the common earth and connecting to earth dolly all as specified as directed by Engr -in- charge.

(a) One light point/bell point/one fan/exhanust fan controlled by one,one way switch.

(b) For one 5 pin, socket outlet 5/6 amp on independent board with other switches

M&L for point wiring complete with stranded copper conductor 4 sqmm single core (nominal area ) PVC insulated and unsheathed cable 650 volts grade drawn in and including medium duty concealed in PVC concealed conduit conforming to IS and ISI marked not less than 19 mm dia with 1.6mm thick concealed pressed steel terminal boxes with plate and framecover for rquired module including single core stranded copper conductor 2.5 sqmm PVC insulated unsheathed cable in same conduit as earth wire to the common earth and connecting to earth dolly all as specified for one 6 pin socket outlet two in one 16/6 amps on an independent board.

M&L for switch modular type single pole one way 6 amps complete all as directed by Engr - in - charge.

M&L for switch modular type single pole one way 16 amps complete all as directed by Engr - in - charge.

M&L socket outlet 2 in 1, 3/5 pin 6 Amp modular type multipurpose complete all as specified and directed by Engr-in-Charge

M&L socket outlet 2 in 1,3/5 pin 16 Amp modular type multipurpose suitable for same board complete all as specified by Engr-in-Charge

Supply and fix LED lights fitting 1x 20 Watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable Size from ceiling rose complete all as specified and as directed .Make :- Phillips/ Bajaj/CG

Supply and fixing LED building light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics with three core flexible copper conductor cable of suitable Size from ceiling rose to light fittings complete all as specified and as directed .Make :- Phillips/ Bajaj/CGcomplete with IP 65/66 protection

Supply & Fixing bracket for street light fittings made out of 32 mm bore medium grade GI tubing 1.2 m long bent to shape and including suitable size of MS clamps, nuts, bolts and washers applying two coats of aluminium paint over a coat of red oxide zinc chrome primer repair complete all as specified and directed.

S&F in replaceent of MCB DB sheet enclosure load line SPN 240V with 200 Amp suitable Size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated Acrylic double door complete confirming to IP 43 with enclosure blank plates for unused way suitable for 12 way complete all as specified and directed :

S&F MCB SP 240 volt, 6 to 32 Amps, C series, 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB . (DB will be measured and paid separately under respective items of sch A)

S&F MCBs SPN 240 volt, 6 to 32 Amps, C series, 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB . (DB will be measured and paid separately under respective items of sch A)

S&F electronic Step type , 120 watt -2 modul modular fan regulator . Make : Anchor/Surya/Havells odulardular

M&L ceiling rose , single phase /PVC /Polycarboante isolated body.

Supply and fix exhaust fan steel body, heavy duty, AC Single phase, voltage 230V, 50 Hz, Copper winding of size 380 mm sweep with, blades and frame and lovers complete all as specified and as directed.

Supply and fixing ceiling fans complete, with blades, down rods, electronic regulator and accessories,230 V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE.Five star rated with bushless direct current motor (BLDC) complete all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm X 60cm X 6mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less thatn 1.5 meters below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers GI earth wire with protected by 15mm dia light grade GI pipe and other end connected to earth testing point or main controlling switch as directed incl funnel with watering pipe 20mm bore light grade GI pipe, wire mess , charcol and common salt, concrete earth pit in PCC (1:3:6) type C1 cast iron frame cover , including necessary excavation, earth work in soft/loose soil and disposal of soil to a distance not exc 50mtr and necessary testing complete all as shown in electrical plate No 3 of MES schedule Part I and testing all as directed.

Please Enable Macros to View BoQ information