SPECIAL REPAIR TO BLDG NO 83 (T-LINE) AT BAKLOH CANTT

Amount

Schedule "A" Part-I & Part-II:- Demolition of precast concrete articles and precast block walling, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete,all as specified.

Demolition of stones or brick masonry, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete,all as specified.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.

Taking down chowkhats or frames exc 1.50 sqm but n.exc 4.00 sqm with shutters (without taking off shutters from the frames) all as specified & directed.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Dismantling timber scantling in any position over 40 sq. cm and over in section, in unframed work, all as specified.

Dismantling plain or corrugated steel sheeting any guage, thickness including Nainital or similar pattern roof covering, all as specified.

Precast cement concrete M-10, type C-1, solid blocks (using 20mm graded aggregate) as in solid block masonry exceeding 10 cms in width, set in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified. Note: (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be paid under respective Items of BOQ.

Walling random rubble masonry with best quality locally available stone (bakloh stone), uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 (1 cement : 6 coarse sand), all as specified.

Walling random rubble masonry with best quality locally available stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 (1 cement : 6 coarse sand), but except stone all as specified. Note: Servicable stone retreived from demolition under respective Items of BOQ shall be reused.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe 410 -W (Gde-E- 250) quality-A, steel work duly painted with one shop coat of zinc chromate primer including preparation of surfaces all as specified.

Steel clip-in false ceiling system with steel plain, perforated, beveled edged tile (600mmx600mm) manufactured out of 0.50 mm thick polyster coil coated galvanised steel having 180 grams zinc coating. Coil coated steel tile shall have 20 micron polyster coated finish on front side and back coat of 5 micron alkalys primer. Two sides of each tile shall be raised and piped and stopped to ensure positive engagement into the spring clip-in profile allowing for demounting of individual tiles. The rigid suspension system consists of rows of galvanized steel 0.50 mm thick clip-in profile of size 38mm x 20 mm and installed at 600 mm c/c spacing to support the tiles. Wall suspension angle, clip-in profiles shall be suspended and jointed fs of size 24 mm X 24 mmX 0.40mm thick are suspended from roof structure by GI ceiling brackets. wall suspension angles of size 24mmx24mm and 0.40mm thick are suspended from the roof structure by GI ceiling brackets. Wall suspension angle are made of coil coated steel matching the colour of tile. They are jointed to the clip in-profile system by hold on clamps. The tiles/ planks are held in place by pressure clips as per manufacuters instructions for spacing. In the flexible system the hanger and butterfly clip replace the suspension angle including necessary scaffolding all as per manufacuters specifications/ instructions and specified and directd by GE. Make:- As per Appendix "C".

Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Prepainted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, hips, valley/ eaves/ rain water gutters, drip and straight flashing (length and girth as fixed), fixed with self tapping screws all as specified and directed.

Factory made solid PVC Door Frame of size 50mm x 95mm made out of 5mm thick single side prelaminated PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 160 of MES SSR 2010 Part-II

Factory made EPS core solid PVC moulded door shutter with wood free EPS board, 30 mm thick (stiles) with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelaminated PVC Sheet on the front face & 2mm Plain prelaminated PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing on Page No. 161 of MES SSR Part-II. The door shall on all edges to be sealed with lipping of 10 mm (5 mm X 2) thick and 25 mm wide PVC sheet for three sides and 60 mm wide PVC sheet for lock side. The lipping shall be bonded to the 2 mm moulded/ plain PVC sheet with solvent cement all as specified and directed.

Mat finish, premium quality, joint free, coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm (600mm X 600mm), as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

30mm thick cement concrete M-15 (Nominal mix) type B-0 (using 12.5mm graded crushed stone agg ) as in flooring, finished even & fair complete all as specified and directed.

Rendering cement plaster 15 mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer), on fair faces of brick walls/ concrete surface in cement mortar 1:4 (1 cement : 4 coarse sand) and finished even and smooth without using extra cement complete all as specified.

Rendering cement plaster 15 mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer), on other than fair faces of brick wall or on stone masonry surfaces, trowelled to even and smooth finish without using extra cement complete all as specified.

Bib taps, 15mm bore, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down high pressure, screwed for iron pipe or for brass ferrule fixed in repairs, all as specified.

Chromium plated angle valve/ stop valve concealed type, cast copper alloy with long shank, 15mm bore, screwed down, high pressure with crutch or butterfly handle both ends screwed for iron pipe or for union etc. fixed in repairs all as specified.

PVC connection 15mm size with PTMT nuts at boths end 300mm long and fixed in repairs, all as specified.

Cast copper alloy, chromium plated 15mm bore, centre hole mixer, half turn with capstan head for mixing hot or cold water with long screwed shanks screwed for iron pipe complete, all as specified.

PVC waste pipe with union, flexible suitable for wash hand basin or urinals, 32 mm dia, fixed in repairs, all as specified.

Wash hand basins, Vitreous China (White) size 550mmx400mm, excluding tap etc including brackets with 32 mm bore waste fittings, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, PVC connections 15mm size with CP brass coupling nuts of length 450mm, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, chain and plug, PVC 32mm dia flush pipe and all accessories fixed in repair complete as all specified and directed. Make: Cat Part No. 1008 of Cera or equivalent makes mentioned in Appx 'C'

Vitreous China wash down water closet (pedestal pattern), white including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC white seat cover and chromium plated jet including PVC connection, fixed complete including demolition of old unservicable WC and provision of plain cement concrete M-15, type B-I, using 20mm graded crushed stone aggregate, fixed in repairs all as specified. Make: Cat Part No. 2008 for EWC, 2308 for seat cover, 2201/B for internal fittings of 'Cera' or equivalent in makes mentioned in Appx 'C'

Vitreous China urinals of size 440 X 315 X 265 mm, crystal white, small, half stall urinal, with 32 mm bore waste fittings, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement with brackets, flush pipe, trap, grating and Union for discharge pipe including fixing supply pipe to flushing cistern, trap and waste pipe, fixed in repairs all as specified and directed. Make: Cat Part No. 5001 of 'Cera' or equivalent makes mentioned in Appx 'C'

PVC valve less, crystal white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, in repairs, all as specified. Make: Cat Part No. 2602 of Cera or equivalent in makes mentioned in Appx 'C'.

Chromium plated toilet paper holder with flap recessed type, fixed to walls with CP brass screws, fixed in repairs all as specified. Make: As mentioned in Appx 'C'

Chromium plated health faucet (ABS body with 1 metre long PVC tube and wall hook complete with accessories, fixed in repairs all as specified.

Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms), fixed with chromium plated brass screws, complete fixed in repairs all as specified.

Brass chromium plated tubular towel rail 20 mm dia, "D" type, 60 cms long between flanges fixed in repairs with and including chromium plated brass brackets, brass screws complete fixed in repairs all as specified

Grating round 140 mm size of PTMT (Minimum weight 50gms), fixed in repairs all as specified.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Applying two coats of cement base paint over a coat of white wash on newly plastered or previously undecorated wall surfaces including preparation of surface, tint and shade as approved by Engr-in-Charge.

Prepration of old wall surface by removing existing treatment by scarping, brushing etc including making surface clean , dry and free from any loose paint film, dirt, chalk, grease, fungus and algae and filling holes, dents, cracks with mixture of white cement mortar and applying two coats of oil bound distemper over a coat of primer over 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Painting two coats with synthetic enamelled paint on new steel or iron surfaces of any description exceeding 10cm width/ girth including preparation of surfaces over a coat of red oxide primer all as specified and directed.

Taking down point wiring with aluminium/ copper conductor for light point, socket point/ power point etc. in PVC casing and caping, surface pvc/ steel conduits, wood batten with clips including taking down board any type and size complete with any type of switches, sockets, holders, (batten or pendent type), ceiling rose etc. The light fittings (any type), main switches, distribution board with MCB’s of any capacity and make are to be removed/ replaced if required and all as specified and directed. NOTE: - Existing fan regulator (any type) and electric meters are to be refixed and connected properly where required.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multistrand) PVC insulated ISI Marked unsheathed cable in and including PVC concealed (concealed wiring) conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marking, medium grade, ISI marked with all fittings/ accessories as specified in preamble 1 (a) to (q) of Section 19 of SSR Part-II, under heading point wiring, cutting chases, making good in cement mortar in CM (1:3), finishing surfaces to match with existing and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as earth wire (green colour) connected to common earth dolly for modular fitting, modular box sunk for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for one light point or one fan point through regulator or one bell point, controlled by one way switch/ push button complete all as specified and directed.

All as per serial item No '41' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per serial item No '41' above, but for one 3 pin 5 Amps socket outlet, independent all as specified and directed.

All as per serial item No. '41' above but for 3 pin 15 Amps socket out let independent with 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Switch piano flush type, single pole, one way, 5 Amps, all as specified.

Socket outlet two & three pin 5Amp flush type, all as specified.

Switch piano flush type, single pole, one way, 15 Amps, all as specified.

Switch out let two in one, 3 Pin 5 amps and 15 amps, flush type, all as specified.

Lamp holder, PVC/Polycarbonate type with back plate suitable for angular/ batten fittings, all as specified.

Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified.

Renewal of wall mounted LED integrating batten fitting T5, 20 Watt LED, 4 feet, PVC extruded with 20 watt LED tube rod with all acessoreis prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete, all as specified and directed. Havell's Cat Part No. LHEBTP7UN1W018/ C&S Cat Part No LTTB4F20WLEDP/W/ Philips CAT Part No BN021LED20S-6500 NW PSU GR or equivalent in makes mentioned in Appx 'C'.

LED lamps, 10 watts all as specified and directed. Make:- CAT Part No LHLDEUEEML8R010 of make "Havells" or equivalent in makes mentioned in Appendix "C".

Energy efficient LED ceiling light 36 Watts of size 2 feet X 2 feet complete with all accessories and fixtures including LED lamps with all acessoreis prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete, all as specified and directed. Make : Cat Part No. LCPL-36-CDL (2X) of 'Crompton' or equivalent in makes mentioned in Appx 'C'.

Renewal of bulk head LED light fitting, 6 Watts with deep drawn anodised aluminium body, epoxy white powder coated, heat resistant prismatic glass cover with specially designed glass cover with 6 watts LED lamp with all acessoreis prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete. Make:- Crompton Greaves Cat Part No. CG80IB6WLEDor equivalent in makes mentioned in Appx 'C'.

Renewal of mirror optics linear and compact 9 Watt mirror light with decorative grey end caps, polycarbonate body and ribbed opal diffuser complete with all accessories and fixtures with extruded polycarbonate, environmental friendly with 9 watts LED tube rod/ lamp with all acessoreis prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete, all as specified and directed. Make : Havell's Cat Part No. LHEXARP7PN1W009 or equivalent in makes mentioned in Appx 'C'.

Renewal of sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 8 way, double door, 240 volts with 200 Amp rated bus bar including taking down old unservicable ICDP/ DB's including KIT KAT fuses/ MCB's (SPN/ SP), all as specified. Make : Cat Part No. 811807 of 'Indo Asian' or equivalent in makes mentioned in Appx 'C'.

Renewal of sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 12 way, double door, 240 volts with 200 Amp rated bus bar including taking down old unservicable ICDP/ DB's including KIT KAT fuses/ MCB's (SPN/ SP), all as specified. Make : Cat Part No. 811808 of 'Indo Asian' or equivalent in makes mentioned in Appx 'C'.

Sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded RLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 4 Sqmm and drawn into and including PVC concealed conduit with all fittings/ accessories, junction boxes 1 to 4 way 20mm dia, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly, complete and as directed. Note :- (i) Two run (each run of 1 RM) of 6 sqmm copper conductor, one RM of earth wire of 4 Sqmm and one RM of concealed PVC conduit, shall be measured as one RM. (ii) Cost of cutting chases in walls and making good disturbed surfaces in cement mortar (1:3) including finishing surfaces to match with existing shall be deemed to be included in unit rate quoted by bidder.

Sheet metal enclosures of size 90 x 60 x 20 cms complete with double door hinged shutter and locking arrangements, dust and vermin proof, fabricated out of 2mm thick MS sheet on suitable size of angle iron frame flushed/ semi flushed/ or grouted on wall including mounting arrangements for energy meters and DB TPN/ SPN including DIN rail channel for mounting MCB's in three rows and TPN bus bar channel of rating 200 Amps duly mounted on 'F' class insulator with colour coded heat shrinkable sleeves and powder coated paint after preparation of surfaces with suitable glass vision panel, front opening painting on internal and external surfaces including taking down old unservicable sheet metal enclosure from the building and making good damaged/ distrubed surfaces to match with existing complete and all as specified and directed.

MCB SPN 63 Amp, 240 Volts, 10 kA all as specified. Make : IndoAsian Cat Part No. 811154 or equivalent makes mentioned in Appx 'C'.

MCB SP 6 to 40 Amp, 240 Volts, 10 kA all as specified. Make : IndoAsian Cat Part No. 811008 to 811016 or equivalent makes mentioned in Appx 'C'.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC M-15, type B-I using 20mm graded crushed stone aggregates with 40mm thick cover of RCC M-15, type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

M/s. Rishav Sood

Havish Construction

M/s Joginder Paul Bhatia

m/S Varun Gupta