SPECIAL REPAIRS TO BLDG NO T-217 (1 to 8) NP LINE OF ASC CENTRE (SOUTH) - 2 ATC UNDER GE (CENTRAL) BANGALORE

Dismantling of Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed.

Demolition of brick work,precast concrete block walling or stone boulder masonry,built in cement mortar including all quoins, arches, pillars, etc complete all as specified and directed.

Demolition of unreinforced cement concrete in floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M & L for Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer in Charge

Dismantling structural steel including gates ,purlins,rafters but excluding trusses complete all as specified and directed by Engineer in Charge.

Fabrication and Re-fixing only rolled sections as in main and cross beams ,hip and jack rafters; pulins where connected to common rafters and running rails ; fixed with angle cleats or other connecting plates complete all as specified and directed.

M&L for providing PCC type B0,1:2:4 (12.5 mm graded aggregate) in roof kerbs or mud stops,rounded or chamfered on edges complete all as specified and directed.

Taking down chowkhats or frames n.exc 1.5 Sqm (with out taking off shutters from the frame) complete all as specified and directed.

Taking down chowkhats or frames exc 1.5 Sqm and n.exc 4.00sqm (with out taking off shutters from the frame) complete all as specified and directed.

Taking down cement plaster on Brick / Concrete surfaces incl raking out joints, hacking for key scrubbing down with water and Removing Rubbish of the MD Land all as directed by Engineer-in-Charge.

S&F IInd class hardwood in scantlings, rectangular or triangular in section,clean sawn, framed and fixed complete all as specified and directed.

S&F Plain, solid, straight 2nd class hard wood frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

S&F 19mm thick MDF Board both side finished as in wardrobe no of compartments & Drawers all as specified and as directed by Engineer-in-Charge.

S & F 40mm width Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed by Engineer in Charge

M&L for 18-20mm thick Sadherhali stone slab flooring, steps, jambs, pillars, window- cills, steps/stairs, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit including 15 mm thick screed bed in CM 1:4 and Rounding to edges complete all as specified and directed by Engineer in Charge

M&L for 18-20mm thick Sadherhali stone slab for skirting, riser, dado and like jointing in cm (1:3) cluding pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit including 10 mm thick rendering in CM 1:3 complete all as specified and directed by Engineer in Charge

S&F rolled sections as in main and cross beams ,hip and jack rafters; pulins where connected to common rafters and running rails; fixed with angle cleats or other connecting plates complete all as specified and directed.

S & F for 4 mm thick of size 600mm x 600mm HSPC (High pressure steam cured) pre-primetered self embossed, textured designer board E-Board Classic( White colour) to be fixed and including GI based frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screw at 450mm centre to centre/ intermediate channel 09mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with & incl ceiling section(n.exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm fixed to intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre suspended with 6 mm dia GI barhangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purline from the roof with alignment clip including providing provision for light fixtures of any size including dismantling of old unsv false ceiling complete all as specified and directede.

M&L Rendering 15mm thick in CM 1:6. finished even & smooth without using extra cement to walls all as specified and directed.

M&L Rendering 15mm thick on brick or concrete surface in CM 1:4, finished even and smooth with out using extra cement complete all as specified and directed by Engineer in Charge

M&L Rendering 10mm thick in CM 1:4. finished even & smooth without using extra cement to walls all as specified and directed.

M& L for rendering 20 mm thick in two layer first layer is 10mm thick in CM1:6 and second Layer is 10mm thick in cm (1:4) on stone Masonry surfaces and finished even and smooth without using extra cement and mixed with water proofing compound as per manufacturer instructions complete all as specified and directed

M&L for preparation of newly plastered surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004,alkali & fungal reisistance, dirt resistance exterior paint of required shade ( Company Depot Tinted ) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.9 litre/ 10 Sqm including complete all as specified and directed.

All as per item No 23 above but on old surfaces complete all as specfied and directed.

Supply only Liquid water proofing compound complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distember over 1 to 2 mm thick putty finish complete all as specified and directed.

M&L for preparation of old plastered / decorated wall surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and appyling two coat of Oil Bound Distemper over a coat of alkaline resistant primer including necessary scafolding and safety measures as required complete all as specified and as directed by Engr-in-Charge.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed by Engr-in-Charge.

S& F for 0.80mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed by Engr-in-Charge.

S &F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as inroof covering/cladding towall,fixed with self tapping screws complete all as specified and as directed.

S &F for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as inroof covering/cladding/ridges towall,fixed with self tapping screws complete all as specified and as directed.

M&L for precast cement concrete block (Type C1, 1:3:6, 20 mm graded aggregate) masonry with solid block,exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for cutting holes in brick walls Exc one Brick, but not two bricksbuilt in cement mortar for inserting hold fasts and making good dismantled portion in cement concrete 1:2:4 type B-1 as required complete all as specified and as directed by Engr-in-Charge.

S & F Pressed steel door frames ( 125mm x 60mm) with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and as directed by Engr-in-Charge.

S & F Pressed steel door frames ( 105mm x 60mm) with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and as directed by Engr-in-Charge.

S & F Mild steel bands, straps, support clamps, hold fasts etc and similar small articles conforming to Fe-410-0 or 310-0 complete all as specified and as directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) as in coping, block for hold fast block or for filling up any chowkat of any description or similar work and finished the surface with existing and including form work complete all as specified and as directed by Engr-in-Charge.

S&F Powder coated aluminium sliding window (three way) frame & shutter with glazed shutter and without wiremesh shutter /skeleton section with the following details complete all as specified and as directed by Engr-in-Charge. :- (i) Aluminium frame section 116x36.50x1.80mm. (ii) Aluminium shutter glazed/skeleton section 50x20x1.50mm thick. (iii) Aluminium grill size 50mmx50mm and 4 to 5mm thick bars complete all as specified. (iv) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape. (v) 4mm thick glass orinary quality and fixed with rubber gasket for with glazed shutter etc. (vi) Stainless steel wire mesh 0.36mm nominal dia avg aperature 1.14mm and fixed with rubber gasket for without glazed shutter etc. (vii) Aluminium disc /bow hanle and locking system complete

S&F Powder coated aluminium Ventilator (partially fixed glazing and Partially louvered glazing) with the following details complete all as specified and as directed by Engr-in-Charge :- (i) Aluminium frame section 45x25x1.80mm. (ii) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape. (v) 4mm thick frosted glass orinary quality (partially fixed glazing and Partially louvered glazing) and fixed with rubber gasket for with glazed shutter etc.

S&F Second class hardwood 30 mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc.edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24(a) complete all as specified and directed

S &F for Flush shutters 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engineer in Charge

Supply and fixing Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 125 mm Butt hinges, medium weight, cold rolled, mild steel complete all as specified and directed.

S & F 40mm width of flaps Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed

S&F 150 mm extruded aluminium alloy handles fabricated type complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel towerbolts of extruded section and fixed complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel towerbolts of extruded section and fixed complete all as specified and directed.

S&F 300 mm long aluminium alloy,anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 140mm floor door stopper of aluminium alloy body and tongue,anodised,with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F 300mm,Mild steel ordinary rat tail rod pattern springs,including roller and roller plate complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge,such as in steps,cooking platform,and other similar situations complete all as specified and as directed.

M&L for 18-20mm thick Granite work in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite lncluding rounding of edges complete all as specified and directed.

M&L for 25 mm thick cement concrete type B-1,1:2:4 (20 mm graded aggregate) is used for levelling course complete all as specified and directed.

M&L for coloured joint free non-skid ceramic tiles 7 to 8 mm thick area of each tile exc 0.11 sqm but not exc 0.18 sqm,in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing including screed bed of CM 1:4,10 mm thick complete all as specified and directed.

M&L for coloured joint free non-skid ceramic tiles 7 to 8 mm thick area of each tile exc 0.11 sqm but not exc 0.18 sqm, in as Skirtings etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering in CM 1:4, 10 mm thick as backing coat to receive wall tile or dado complete all as specified and directed.

M & L for coloured Glazed ceramic tiles in vertical surface 450x300x7 mm mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick backing coat in CM 1:4 all as specified and directed by engineer in charge

M&L for preperation of new steel surfaces and applayingtwo coat of synthetic enamel paint over a coat of red oxide, zinc chrome complete all as specified and as directed by Engr-in-Charge.

M&L for old steel surfaces and applayingtwo coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.

M&L for PCC 1:3:6 type C1 using 40mm graded aggregate of 75mm thick as in Plinth Protection finishing even and smooth without using extra cement complete all as specified and directed.

S & F of 50mm x 47 mm size PVC solid door frame of size made out of 5mm plain Colour PVC sheet reinforced with MS square tube , supplying and fixing in opening as per specification and drawing shown in SSR 2020 Part II. complete all as specified and as directed.

S & F of 30mm thick factory made solid panel PVC door shutter (with fittings) (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain Colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck in side with solvent cement for stiles and plain Colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain Colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification and drawing shown in SSR 2020 Part II complete all as specified and as directed

Taking up or down steel water tubing galvanised along with fittings and connections 40 mm bore or any other type of pipe and removing to store or cleaning for refixing with new pipes and fittings complete all as specified and as directed.

Taking up or down steel water tubing galvanised along with fittings and connections 25 mm bore or any other type of pipe and removing to store or cleaning for refixing with new pipes and fittings complete all as specified and as directed.

Taking up or down steel water tubing galvanised along with fittings and connections 20 mm bore or any other type of pipe and removing to store or cleaning for refixing with new pipes and fittings complete all as specified and as directed.

Supplying and laying 40 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling (Concealed/surface) or laying in floors complete all as specified and directed.

Supplying and laying 25 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling (Concealed/surface) or laying in floors complete all as specified.

Supplying and laying 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling(Concealed/surface) or laying in floors complete all as specified.

S & F in repairs stop valves/Angle cock 15 mm bore fancy type chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engr-in-Charge.

S & F in repairs stop valves/Angle cock 15 mm bore fancy type concealed type chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engr-in-Charge.

S & F in repair fancy type Bip taps 15 mm bore cast copper alloy Chromium plated with crutch of butterfly handles screwed down screwed for iron pipes complete all as specified and as directed by Engr-in-Charge.

S & F in repair 2 way bib cock double handle with flange, cast copper alloy chromium plated, screwed down, suitable for 15mm bore iron pipe complete all as specified and as directed by Engr-in-Charge.

S & F in repairs brass chromium plated shower rose of 125 mm size suitable for 15mm bore pipes including shower arm complete all as specified and as directed by Engr-in-Charge.

S & F in repair PVC Waste pipe of size 32/40mm dia for WHB/Sink complete all as specified and as directed by Engr-in-Charge.

S & F for Shelf of PTMT fixed soap dish with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and as directed by Engr-in-Charge.

S & F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including PVC SWR P/S trap connecting to flush pipe and to anti syphonage pipe, flushing cistern of capacity 10 liters, low level, white, with inlet, ball valve, float and handle including bracketsetc. complete including making good to floor., fixed in repairs complete all as specified and directed.

S & F in repair Viterous China hand wash basin along without pedastal white flat back size 550x400mm including brackets and Pillar taps Fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixedand fixed all as specified and directed by engineer in charge

S & F PVC (SWR) 75 mm dia floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S & F in repairs Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) complete all as specified and directed.

S & F 100 mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F 25mm dia Curtain Rod/Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed.

S & F Aluminium anodised Brackets for suitable for 25 mm dia Curtain rod complete all as specified and directed.

S&F in repairs CP health faucet along with 1 m long flexible tube and holding stand including all necessary fittings complete all as specified and as directed

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

Demolition of drain or PVC pipes any diameter including fittings complete all as specified and directed by Engineer in Charge

S & F in repairs 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed

S & F in repairs 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

S & F in repairs 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed

S&F 110 mm PVC (SWR) vent cowl complete all as specified and directed

S & F PVC (SWR) branch piece of 110 mm, single (single T) equal or unequal provided with access door complete all as specified and directed

S & F PVC (SWR) branch piece of 75 mm, single (single T) equal or unequal provided with access door complete all as specified and directed

S&F for PVC Connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

Demolition of reinforced Concrete of any description and in any position not otherwise specifically provided for all as spcified and directed

M & L for Reinforced cement concrete (nominal mix) in chajjas type B0, 1:2:4 wirh 12.5 mm graded aggregate including necessary formwork all as specified and diected by engineer in charge

M & L Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

S & F rotational moulded polyethylene water storage tanks of capacity 1000 litres tripple layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I with tank adaptor, Gun-metal globe gate valves of 25mm dia, with iron wheel head, screwed both ends for iron pipe and fixed and ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed all as spcified and directed

M & L for surface excavation not exc 30cm and avg depth not exc 15cm in soft loose soil complete all as specified and as directed by Engr-in-Charge.

M & L for hard core fo gauge not exc 63mm, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified and as directed by Engr-in-Charge.

M&L for PCC 1:3:6 type C1 using 40mm graded aggregate of 75mm thick as in Sub Base or flooring finishing even and smooth without using extra cement complete all as specified and directed.

Plain Cement Concrete Type C1, 1:3:6 (using 20 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates, back filling of pressed steel door frames, troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work complete all as specified and as directed by Engr-in-Charge.

M&L for chequered cement concrete tiles of 30x30x25 mm thick,with grey cement and pigments set,jointed and pointed in neat cement slurry in floors including screed bed of cement mortar 1:6 ,20 mm thick complete all as specified and directed.

M&L for returning filling of soft/loose soil in including spreading,levelling,watering and well ramming in layers n.exc 25 cm complete all as specified and directed.

Removal of spoil / debris taken out of either demolished / excavation / dismantling out of the MD land to the dumping yard of any distance firstly by raising and filling the removed spoil into the tractor / tipper or any other vehicle designated for carrying the spoil for disposal complete all as specified and as directed

S&F in repairs Stainless steel plate rack of size 600mm x600mm x 250mm including fixed with rawl plug and screws on walls complete all as specified and directed

Cutting chases, pinning in Brick walls/Stone concrete block or slab walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.;and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth complete all as specified and directed

S & F for Aluminium Wall mounted stand 16 feet (4 No of Pipes, 4 ft each) consisting of four anodized, Aluminum pipes, each of outer dia 22 mm and inner dia 19.8 mm, mounted on anodized Aluminium angle of size 30x30x3 mm complete all as specified and directed by Engr-in-Charge.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, bell, light fittings etc removing materials for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc.complete all as specified and directed.

M&L for complete with 1.5 sqmm single core PVC insulated FRLS unsheathed cable 1100 volts grade with multistranded copper conductor conforming to IS-694 1990 with ISI marked (for phase ,neutral and earth) drawn in and including non metalic rigid PVC conduit medium gradewith ISI mark of minimum 20mm dia and all conduit accessories Concealed including cutting / chases in wall /ceiling /fixed to roof /truss/columns etc and including factory made branded make embossed galavanised steel pressed terminal boxes alongwith size modular cover plates with frames fixing modular switches, sockets, regulators etc.of suitable size modules and earth wire to be connected to common earth dolly complete all as specified and directed for the following :- Note:Location of light points,6 Amp socket points and light fittings may be decided by Engr-in-charge as per site/user requirment. (a) One light /Fan /Bell point controlled by one modular switch 6 Amps one way

(b) One 3 pin Point 6 Amps switch socket outlet point controlled by one switch on the independent board complete all as specified and directed.

(c) One 3 pin Point 6 Amps switch socket outlet point controlled by one switch on the same board complete all as specified and directed.

All same as per item No 108 here-in-before but with 2.5 sqmm size single core multistranded copper conductor cable for 3 pin 16 Amps Modular switch socket combination outlet on independent board with 2.5 sqmm FRLS insulated and unsheathed copper conductor as earth and connected to earth dolly complete all as specified and directed.

S&F Modular switch 1 way 6 Amps,1 module all as Specified and directed. (Make: Arteor of Legrand / Zencelo/Avator Of Schneider /Panasonic Vision Of Pansonic / Millenium of ABB / Englaze of L&T)

S&F Modular Type shuttered socket outlet, 3 pin 6A 230 volts 2 modules with ISI mark Complete all as Specified and directed. (Make: Arteor of Legrand / Zencelo/Avator Of Schneider /Panasonic Vision Of Pansonic / Millenium of ABB / Englaze of L&T)

Supply and fix modular switch 1 way 16A,1 module all as Specified and directed. (Make: Arteor of Legrand / Zencelo/Avator Of Schneider /Panasonic Vision Of Pansonic / Millenium of ABB / Englaze of L&T)

S&F Modular Type shuttered socket outlet, 3 pin 6A/16 Amps,230 volts 2 modules with ISI mark Complete all as Specified and directed. (Make: Arteor of Legrand / Zencelo/Avator Of Schneider /Panasonic Vision Of Pansonic / Millenium of ABB / Englaze of L&T)

Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC square blocks complete all as specified and directed.

S&F Modular switch bell push button 6 Amps 230 volt one way complete all as specified and directed. (Make: Arteor of Legrand / Zencelo/Avator Of Schneider /Panasonic Vision Of Pansonic / Millenium of ABB / Englaze of L&T)

S & F, Ding Dong AC, 230 volts, single pole complete all as specified and directed.

S&F Stepped type electronic modular fan regulator 1-module, 230 Volts AC complete all as specified and directed. (Make: Arteor of Legrand / Zencelo/Avator Of Schneider /Panasonic Vision Of Pansonic / Millenium of ABB / Englaze of L&T)

S&F in replacement LED tube light fitting of 20 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

S&F in replacement LED tube light fitting of 10 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

S&F inrepair bldg security light light fittings 1x 25 Watt LED street light with cast aluminium housing, toughened flass diffuser, IP65/66 and wired with all accessories and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size all as specified and directed.

S&F steet light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete including taking down unserviceable one all as specified and directed.

M&L for Sub main wiring with 2 runs of 4.0 sqmm, single core, FRLS insulated & unsheathed cable conforming to IS-694, FRLS, 1100 volts with copper conductor multi stranded drawn in existing non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 2.5 sqmm single core FRLS insulated & unsheathed copper conductor FRLS Cable as continuos earth wire dolly and connecting to existing main switch board / distribution board of the building as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and directed.

Supply and fix in replacement Sub main wiring with 2 runs of 6.0 sqmm, single core, FRLS insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in existing non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 6 sqmm single core FRLS insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and directed.

S&F Sheet metal enclosure (ISI marked) acrylic distribution board for TPN 4 way , 415 V TPN Acrylic DB, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

S&F in replacement Sheet metal enclosure (ISI marked) Acrylic distribution board for 240 volts, SPN 8 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

S & F MCB single pole 6 to 32 Amps 240 volts, C Curve, 10 kA rupturing capacity providing in DB complete all as specified

S & F MCB single pole & neutral 6 to 32 Amps 240 volts, C Curve, 10 kA rupturing capacity providing in DB complete all as specified.

Supply and fix in repair MCB Tripple pole & neutral 40 to 100 Amps 415 volts, C series,10 kA rupturing capacity providing in DB complete all as specified.

S&F in replacement of sheet metal enclosure of size 850 x 850 x 150 MM grouted on wall/floor in PCC with nuts and bolts made out of 2.0 mm thick CRCA sheet, having Nine nos chamber for housing of Eight energy meters and SPN MCB with Peeping glass fixed PVC frame and one MCB SPN with fixing rail and suitable busbar chamber for fixing four Nos aluminium strips 300 Amp capacity each making holes for fixing aluminium lugs, complete internal wiring with 6 sqmm multistranded copper cable FRLSH, epoxy based bakelite sheet of suitable size for fixing of energy meters & MCBs, including indl chamber locking system.The quoted rate includes the cost of seven nos MCB SPN 32 Amp complete all as specified and directed by Engr-in-chagre.

Taking down ceiling/exhaust fan dismantling and painting of ceiling/exhaust fan complete at site with synthetic enamel paint by spraying incl (fittings with filler) one coat after cleaning all dust etc incl connecting up. Provn of twin core cable of suitable size for ceiling rose to connector connecting of earth wire incl replacement of fan capacitor 2.5/3.15 MFD,canopy, bearing/bush, rubber bushes minor nuts bolts screws washers greassing in fan bearing & refix same complete all as specified and directed

Rewinding of ceiling fan with 1200 mm sweep size of copper enamelled wire including varnishing, heating with proper insulation complete and testing all as specified and directed.

Rewinding of Exhaust fan with appropriate size of copper enamelled wire including varnishing, heating with proper insulation complete and testing all as specified and directed.

S&F exhaust fan Including making necessary opening for fixings sweep made of sturdy Engineering plastic complete with louvers shutter,voltage 230 V, 50 Hz, 1200 RPM noiseless,copper winding of sweep 200/225 mm with self closing louvers and blades as per existing complete fittings all as specified and as directed. NOTE: Quoted rate deemed to be included for providing hole by opening in any type of walls in the building including neccessary plastering, grouting of nuts & bolts and washers suitable size and neccessary fixing arrangement for fixing louvre and including making good to disturbed surface area to its original position complete all as specified and directed.

M & L for Earthing complete with galvanized steel earth plate electrode 600x600x6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4.0mm dia by means of bolts,nuts,check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point all as specified or indicated including testing on completion including dismantling of old earthing materials complete all as specified and directed.

Taking Down any type and size of Geysers and refixed in orginal position any description after necessary water connection & all necessray fittings complete all as specified and directed.

S&F GI tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, size of 25 mm bore with and including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc, incl taking down of old unsv GI tubing complete all as specified and directed

S&F Gun-metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778 : 1984, size of 25 mm inclduing taking down old valves complete all as specified and directed.

S&F GI tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, size of 40 mm bore with and including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc, complete all as specified and directed

Cutting of existing GI/DI Pipe and connecting the pipe line with connected items all as specifoed and directed

Excavation in trenches in soft/loose soil n.exc 1.5m wide and n.exc 1.5m in depth for laying pipes or foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n.exc 10sqm on plan and n.exc 1.5m in depth and getting out in any type of soil complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm in any type of soil complete all as specified and directed.

Removing excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.