CANOPY & SIGNAGE REPAIR AGRA RRO

SUPPLYING&TRNSPT,FBRCTN 7001-AGRA RETAIL RO — "SUPPLYING, TRANSPORTING, FABRICATING, ERECTING IN POSITION IN POSITION OF PRE- FABRICATED STEEL STRUCTURES AT ALL ELEVATIONS FOR CANOPY USING STRUCTURAL STEEL SECTIONS ISMB/ISMC/ISA CONFORMING TO IS:2062 AND IS 226 , INCLUDING CUTTING, WELDING OR BOLTING, SUPPLY OF BOLTS/NUTS/WASHERS ETC., COMPLETE AS PER DRAWINGS INCLUDING SURFACE PREPARATION AND APPLYING ONE COAT OF ZINC PHOSPHATE PRIMER BEFORE ERECTION, ONE COAT AFTER ERECTION AND TWO COATS OF SYNTHETIC ENAMEL PAINT AS PER SPECIFICATION AFTER ERECTION AND ALL MATERIALS AND LABOUR COMPLETE. ( NO WELDING IS PERMITTED AT SITE). THE RATE QUOTED SHALL INCLUDE COST OF BOLTS, NUTS, WASHERS, WELDING AND ELECTRODES AND ANY OTHER CONSUMABLES REQUIRED FOR COMPLETING THE WORK. NUT BOLTS SHALL NOT BE CONSIDERED FOR PAYMENT.THEORETICAL WIGHT OF STEEL SECTIONS SHALL BE CONSIDERED FOR PAYMENT..(.(NO MEASUREMENT SHALL BE TAKEN FOR NUT,BOLT,WASHER SPLICE PLATE & GUSSET PLATE) "

SUPPLY&FIXING,CLIPPON — "Supply and fixing Clippon Roofing System:

PROVIDING&FIXING,FALSE — "Providing & fixing false ceiling system of Trac 150 F exterior grade or approved equivalent of 0.5mm thick galvanised steel with stove enameled coil coated finish inter locking ceiling panels, carriers, suspension system and edge closure as per the following specification. Supplying and installation of exterior grade 150 F ceiling system comprising of 150 mm x 17 mm deep panels roll formed out of 0.5 mm galvanised steel with stove enameled coil coated finish. The panels shall be pre-treated and coil coated on one side in manufacturers standard colour shades as approved by the Architect/ Engineer in charge. The rear side of the panel shall be given a coat of primer and a wash coat while the finished side shall be given a coat of primer and finish colour coat in polyster paint for a min. dry film thickness of 20 microns, fixed on to the roll formed carriers 34.5 mm x 488 mm deep out of 6 mm thick Galvanised steed with prongs to hold panels in the module of 150 mm at maximum 1.2 mts. C/C. The carriers to be suspended from roof truss by rigid suspension angles as per manufacturer's recommendation. Panels shall be supplied in custom length upto maximum of 5 mts. Job also includes providing ceiling flashing using factory formed 0.5 mm thick Polyster coated galvanised steel material. Rate shall be including providing flashing to cover gap if any between illuminated banding and false ceiling.

SUPPLY AND FIXING FOR — "Supplying and fixing 20 SWG GI sheet facia including painting with one coat of zinc chromate primer and two coats of 1 st quality synthetic enamel paint on front side . Necessary facia framework for fastening the sheet to the canopy securely shall be paid separately.

SUPPLY&FIXING,80W LED — "80 W LED FITTING AS MENTIONED IN IS STANDARDS IS 16101 TO 16107:SUPPLY AND FIXING OF 80 W LED HOUSED BY SINGLE PIECE PRESSURE DIE CAST ALUMINUM BODY, RECESS MOUNTABLE FITTING WITH GUARANTEED BURNING HOURS OF 50000 .MAKE PHILIPS/HAVELLS/BAJAJ/WIPRO/OSRAM/CROMPTON/GE/BEVE R INNOVATIONS. IP PROTECTION OF MINIMUM IP 65 AND ABOVE, SUITABLE FOR CANOPY LIGHTING AT RETAIL OUTLETS (PETROL STATION) .THE BIDDER SHOULD SUBMIT COPY OF CERTIFIED PHOTOMETRIC REPORT AS PER IESNA LM- 79(APPROVED METHOD FOR THE ELECTRICAL AND PHOTOMETRIC MEASUREMENTS OF SOLID-STATE LIGHTING PRODUCTS) FROM A UL/ ERTL /ERDA OR ANY NABL ACCREDITED LABORATORY TO VALIDATE THE PHOTOMETRIC CLAIMS AS & WHEN ASKED BY HPC. A MINIMUM 3 YEARS WARRANTY FROM MANUFACTURING DEFECTS FOR THE LUMINAIRE BY MANUFACTURER.I) WITH HIGH LUMEN EFFICACY LEDS FROM CREE, SEOUL SEMI-CONDUCTOR, LUMILED PHILIPS, OSRAM, NICHIA (JAPAN), TRIDONIC (AUSTRIA), GE AND BRIDGELUX . EFFICIENCY OF MORE THAN 90 LUMENS PER WATT . LEDS USED IN THE FIXTURE SHOULD BE FROM THE SAME BIN AND CERTIFIED AS PER LM-80 (IESNA: APPROVED METHOD FOR MEASURING LUMEN MAINTENANCE OF LED LIGHT SOURCES AND LED LUMEN DEPRECIATION TIME TO L70 BASED ON LM-80 DATA). BY ANY UL/ ERTL /ERDA OR ANY NABL ACCREDITED LABORATORY TO VALIDATE THE PHOTOMETRIC CLAIMS AS & WHEN ASKED BY HPC.II) BOTTOM OPEN ABLE FOR EASY MAINTENANCE.III)HIGH QUALITY POLYCARBONATE OPAL DIFFUSER FOR OPTIMUM UNIFORMITY AND GLARE FREE LIGHT OUTPUT.IV) GENERAL ELECTRICAL PROTECTION AGAINST HIGH VOLTAGE AND SURGES UP TO3 KVV) POWER FACTOR > 0.95VI) RANGE ALLOWED FOR TOTAL SYSTEM WATTAGE 80 W WITH +2W OR -2W VII) DRIVER OPERATING VOLTAGE RANGE: 140 V- 270 V VIII) OPERATING TEMPERATURE 0 TO +45 DEG CENTIGRADE VIII) CRI MORE THAN 70 IX) COLOUR TEMPERATURE5650K?500K (TO BE MENTIONED IN LM 79 CERTIFICATE) X)WIDE BEAM ANGLE FOR SPREAD OF LIGHT 120 DEGREES OR MORE XI)LUMINAIRE PERFORMANCE COMPLIES TO IS10322 (PART 5/SEC 3) & IEC 60598-1,IEC 60529, ROHS"

SUPPLY,END — END TERMINATION END TERMINATION OF FOLLOWING CABLE WITH DOUBLE COMPRESSION NFLP GLAND AND CRIMPING SOCKETS 4CX2.5 SQMM END TERMINATION

END TERM OF — CABLE TERMINATION USING SINGLE/DOUBLE COMPRESSION BRASS CABLE GLANDS, FLAMEPROOF/NON-FLAMEPROOF WITH EARTH TAGS, CRIMPING TYPE TINNED COPPER LUGS FOR COPPER CABLES AND ALUMINIUM LUGS FOR AL CABLES AND OTHER CONSUMABLES FOR THE FOLLOWING SIZE OF CABLES. APPROVED MAKE OF 3C X 1.5 SQ.MM. INSTRUMENTATION CABLE (DOUBLE COMPRESSION FLAMEPROOF) AT PRESSURE TRANSMITTER. REFER BOQ AND TECHNICAL SPECIFICATIONS FOR DETAIL DESCRIPTION.

SUP & FIX - LED — 40 WATT LED LINEAR LIGHT: SUPPLY, FIXING, TESTING AND COMMISSIONING OF SUSPENDED CEILING LUMINAIRE FOR LED 40 WATT BASE G5, 230 V, DIRECT LIGHT EMISSION, SUPPORT PROFILE ANODISED ALUMINIUM, BATTEN LUMINAIRE WITH RAPID CONNECTION LUMINANCE DIFFUSER), INTEGRAL HF ELECTRONIC CONTROL GEAR DETEC MULTIWATT, WITH SUSPENSION/SUPPORTS AS REQUIRED, PROTECTION CLASS, IP40 L=1200MM B=70 MM, B=85 MM-CAN BE MOUNTED LINEAR PROFILE, LIKE 2400L, 3600L ETC.

PROVIDING&FIXING,AL — "Providing and fixing 2 mm thick Aluminum Sheet Gutters of required shape in slope with 40 mm x 3 mm MS. Brackets at 1000 mm maximum spacing and 8 mm dia G.I. J or L hooks, boltsand nuts, GI Limpet and bitumen washers, providing nut bolt joint , sealing the joints with silicon sealant testing the gutter for leakage by filling water etc. Complete.(Refer attached Drawing .For allowable tolerance refer to IS codes

PROVIDING AND FIXING FOR — "PROVIDING AND FIXING 6"" DIA PVC PIPES OF 6 KG/SQCM OF APPROVED MAKE AS PER IS 4985 FOR RAIN WATER PIPES INCLUDING ALL FITTINGS LIKE BANDS , SHOES ETC., MS FABRICATED BRACKET AS PER REQUIMENT ETC. ALL COMPLETE AS DIRECTED BY THE EIC."