Special repairs to building No P-207 (Chandra Hall), provision of iron grills for SWT and provision of utensil stand in Airmen SMQs at AFS Amla

Amount

B/R Portion Demolition, Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed. (0+0+15)

Demolition of cement concrete (unreinforced) as in ground floor and paving not exc 15 cm thickness below or above ground level complete all as directed. (18.02+0+0)

Taking down cement plaster on brick or stone walls etc, including racking out joints, hacking for key, scrubbing down with water etc. all as directed. (1275+0+450)

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as directed. (40+0+0)

Taking down wooden chowkats or frames exc 1.5 sqm but not exc 4 sqm each (without taking off shutters from the frames) complete all as specified and directed . (8+0+0)

Taking down wooden chowkhats or frames not exc 1.5 sqm with shutters (without taking off shutters from the frames) complete all as specified and directed (3+0+0)

Taking down steel chowkats or frames exc 1.5 sqm but not exc 4 sqm each (without taking off shutters from the frames) complete all as specified and directed. (23+0+0)

Taking down steel chowkhats or frames not exc 1.5 sqm with shutters (without taking off shutters from the frames) complete all as specified and directed (30+0+0)

Dismantling water tanks of a capacity exceeding 250 litres but not exceeding 500 litres and removing to store complete all as directed. (1+0+0)

Taking up or down steel tubing alongwith its connections from any position such as wall, floor, ceiling etc., including cleaning for refixing complete all as specified and directed for the following size of pipes:-

15 mm Bore (30+0+0)

20 mm Bore (20+0+0)

25 mm Bore (20+0+0)

M&L for providing, cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. (0+0+15)

M&L for Precast reinforced cement concrete type B0, 1:2:4 (12.5 mm graded aggregate) in door and windows frames, any size, single or double rebated, including arrangement for fixing of hinges and fixtures as required. (0.28+0+0)

M&L for 75 mm thick PCC 1:3:6 Type B-1 (40mm graded aggregate), as in plinth protection complete all as specified and directed. (50+0+0)

M&L for cutting openings, through brick walls built in cement mortar for the door, window and other openings or enlarging existing openings converting window into door openings, etc. or cutting out defective brickwork for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m complete all as specified and directed. (4+0+0)

M&L for cutting holes in brick walls built in cement mortar for inserting holdfasts or lugs to a depth exceeding half brick but not exceeding one brick from the face of jamb and making good dismantled portion in cement concrete 1:2:4 (type B-1) or cement mortar 1:3 as required at site complete all as specified and directed. (0+0+80)

S&F 40mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. (20+0+0)

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. (5+0+0)

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all specified and directed. (15+0+0)

S&F 100mm size, butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed. (36+0+0)

S&F 100mm size, butt hinges, heavy weight, cold rolled mild steel, complete all as specified and as directed. (0+0+40)

S&F 150mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. (24+0+0)

S&F 150mm long, extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. (24+0+0)

S&F 300mm long, Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. (9+0+0)

S&F Brass chromium-plated tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges fixed on the wall using wooden plugs with chromium-plated brass screws and cup washers complete all as specified and directed. (2+0+0)

S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples all as specified and directed. (0+0+690)

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as specified and dirceted. (0+0+10700)

S&F rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410-W (Gde- E- 250) quality-A all as specified and directed. (0+0+2620)

S&F in repairs collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, including taking down old steel gates complete all as specified and directed. (7.2+0+0)

S&F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed. (45+0+0)

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. (375+0+0)

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for sliding shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. (460+0+0)

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge. Note: Only weight of grill will be measured and considered for payment. (75+0+0)

S&F steel ventilator with top hung shutters including hinges and steel peg stay complete all as specified and directed. (2.64+0+0)

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed. (430.5+0+0)

M&L for machine kota stone slab 20-25mm thick as in riser of steps, skirting, dado and pillar laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing complete over and including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed (20+0+0)

M&L for digital coloured glazed ceramic tiles in vertical surfaces 350 x 250 x 7mm/450 x 350 x 7 mm thick, etc set and jointed in neat cement slurry and pointed in colour cement to match the shade of tiles including 10mm thick backing coat in 1:4 cement mortar complete all as specified and directed. (70+0+0)

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match set, over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed. (40+0+0)

M&L for Endura tiles 30cm x 30cm x 12mm thick conform to IS 4457: 2007, set, jointed and pointed in neat cement slurry with white cement with pigment in floors, including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. (30+0+0)

M&L for Machine cut cudappah stone slab 20-25mm thick as in window cills over and including 15mm thick cement screed base in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. (72+0+0)

M&L for 20mm thick Granite (Z Black) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like including 10 mm thick; cement mortar (1:4) backing coat and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. (7+0+0)

S&F 20mm thick; Granite urinal partitions slab of size 0.75mx1.3m terminating about 40cm above floor line by embedding slab 50mm into the existing wall after necessary cutting holes into or through brick walls built in cement mortar and making good in cement mortar 1:3 and pointing in white cement (1:2) using marble dust with an admixture of pigment to match with the shade of granite complete all as specified and directed. (7+0+0)

M&L for rendering 10mm thick cement mortar 1:6 over brick or concrete wall surfaces finished even and smooth without using extra cement complete all as specified and directed. (650+0+0)

M&L for rendering 10 mm thick cement mortar 1:4 over brick or concrete wall surfaces finished even and smooth without using extra cement complete all as specified and directed. (0+0+450)

M&L for 5mm thick rendering as in ceiling on fair faces in cement mortar 1:3 all as specified and as directed. (150+0+0)

M&L (10+5)mm thick for rendering fair faces of brick work or Concrete surface in two coats 10mm thick in CM(1:6) as under coat 5mm thick CM (1:4) as finishing coat in two separate layer mixed with liquid water proofing compound in finishing coat only with liquid waterproofing compound @ 200ml per bag of cement finished even and smooth without using extra cement complete all as specified and as directed. (405+0+0) Note: Liquid water proofing compound shall be measured and paid separately.

Supply only liquid water proofing compound (4.5+0+0)

M&L for 3mm thick wall care putty on wall surfaces including finishing the surface even and smooth all as specified and directed. (1055+0+0)

M&L for two coats of oil emulsion distemper on wall newly plastered surfaces over a coat of chalk white primer including preparation of new surfaces complete all as specified and directed. (650+0+0)

M&L for two coats of cement base paint on walls, pillasters, cornices, etc., on newly plastered walls over a coat of alkali resistant primer including preparation of surfaces complete all as specified and as directed. (405+0+450)

M&L for preparing of new decorative surface of ceilings and applying three coat of white wash all as specified and directed. (150+0+0)

M&L for preparing of old decorative surface of walls and applying one coat of white wash on ceilings including cornices etc including cracks filling with wall care putty where ever necessary complete all as specified and directed. (440+0+0)

S&F sheet glass 4mm thick ordinary quality and glazing with oil putty in squares not exc 0.50 sqm in each panes in steel window complete all as specified and directed. (54+0+0)

S&F in repairs 3mm thick sheet glass, ordinary quality frosted on one side, for fixing in steel ventilator with glass putty, in square not exceeding 0.5 Sqm in each pane complete all as specified and directed. (2.64+0+0)

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specifed and directed. (44+0+0)

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm in width or girth and applying two coat of synthetic enamel paint over a coat of redoxide, zinc chrome primer complete all as specified and directed. (2.64+0+690)

S&F steel water tubing ISI marked, ‘medium grade’ galvanised, with all fittings such as bends, elbows tees, short, pieces, connections, back nuts, diminishing pieces caps, plugs and unions etc, fixed to walls and ceiling or laid in floors complete of the following sizes:-

15 mm Bore (30+0+0)

20 mm Bore (20+0+0)

25 mm bore (20+0+0)

S&F 500 litres capacity; rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete. (2+0+0)

S&F in repair 15mm bore dia, bib taps, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass, ferrule all as specified and directed. (3+0+0)

S&F in repair 15mm dia Pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete including taking down old rusted tap complete all as specified and directed. (5+0+0)

S&F in repair 15mm dia; Stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. (8+0+0)

M&L for 32mm dia; Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including dismantling old unserviceable one complete all as specified and directed. (5+0+0)

S&F 15mm bore; Push tap suitable for urinals, any colour high pressure of PTMT screwed for iron pipe (Minimum weight 15mm-50gms) complete all as specified and directed. (7+0+0)

S&F Towel Ring of PTMT fixed with and including Chromium-plated brass screws and wooden/ plastic cleats (Minimum weight 90gms) complete all as specified and directed. (2+0+0)

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm fixed to pipes and valves complete all as specified and directed. (12+0+0)

S&F 75mm bore dia, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. (20+0+0)

S&F PVC (SWR) 110mm bore ‘S’ trap including connecting to outlet with solvent cement complete all as specified and directed. (2+0+0)

S&F in repairs brass chromium plated bottle traps of 32 mm bore for wash basins/ urinals with inlet and outlet screwed for pipe or connections including necessary packing, union and cap all as specified and directed. (9+0+0)

S&F in repairs PVC (SWR) nahani trap, plain with grating suitable for 75mm diameter of outlet pipe including jointing with solvent cement and making good the disturbed surface with plain cement concrete 1:2:4 type B-1 complete all as specified and directed. (3+0+0)

S&F in repairs 10 litres PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed. (3+0+0)

S&F in repair 32mm dia waste pipe of polyethylene of low or high density or PVC. 32 mm dia, suitable for vitreous china wash hand basin including taking down old unserviceable pipe complete all as specified and directed. (5+0+0)

S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe all as specified and directed. (7+0+0)

S&F in repairs Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor all as specified and directed. (2+0+0)

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat cover, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. complete all as specified and directed. (1+0+0)

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe all as specified and directed. (5+0+0)

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium-plated bracket guard and railing 60cm long complete all as specified and directed. (2+0+0)

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. (3+0+0)

S&F Stainless steel plate rack of size 900mm x 750mm x 250mm (36x31x10 inch) made of 0.63mm thick stainless steel sheet, S.S Screw & round pipe, including fixing on wall with screw and rawl plug, complete all as specified and directed. (0+90+0) Make:- BlueStar Cat No. SSKPR-315/ Prayag Cat No. P- 348.

E/M Portion Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fitting fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors, etc. complete all as specified and directed. (114+0+0)

M&L for point wiring using approved colour coding as per IS with 1.5 sqmm two single core PVC insulated but unsheathed FR cable, 1100 volts grade, ISI-694 marked with multistranded copper conductor and earth continuity wire with similar 1.5 Sqmm cable (including connecting to earth dolly) drawn through ISI Marked heavy duty rigid PVC concealed conduit with all accessories etc with mild steel sunken box duly,concealed in wall and having PVC modular cover plate with frame suitable for modular switch/Sockets/regulators for the following :-

One light / fan controlled by one switch one way. (82+0+0)

One 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board. (11+0+0)

One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent board. (13+0+0)

All as per item No : 80 but for point wiring with 2.5 Sqmm two single core copper cable and earth continuity wire with 2.5 Sqmm single core cable for one three pin 15 Amp socket outlet point on independent board. (8+0+0)

S&F Modular switch 01 way 6 Amp , 01 module complete all as specified. (106+0+0)

S&F Modular switch 01 way 16 Amp , 01 module complete all as specified. (8+0+0)

S&F Modular socket, 6 Amp - 2/3 pin combined, 02 module complete all as specified. (24+0+0)

S&F Modular socket, 6 Amp/ 16 Amp - 2/3 pin combined, two in one, 02 module complete all as specified. (8+0+0)

S&F in repair Modular step fan regulator, 120 Watt - 02 module complete all as specified. (24+0+0)

S&F in repair ceiling rose of 3 phase/ PVC/ polycarbonate, isolated body all as directed. (82+0+0)

S&F in repair for wall mounted LED 18/20 W CRCA fitting 230 V with extruded aluminium heat sink provided for efficient heat dissipation and integral electronic driver connector block etc., complete with all accessories internally prewired including necessary mounting arrangement, provision of new 2 core multistranded copper conductor of size 0.5 sqmm from ceiling rose to fitting including necessary polycarbonate LED tube 4 feet, 18/20 W complete all as specified and directed. (55+0+0) Make:- Cat no LT8-20-865(2) for rod & DIJB12LT8-20 for batten of Crompton/ Cat no BLRB 18W CW- Pro LED Tube rod & BLRB-DB 118 for batten of Bajaj/ Cat no REGALBATTENT8UPTO1X22WD SBSWH for batten & TITANIANEO1213T8SSTL20WLED865SPC for rod of Havells

S&F in repair for environment friendly high efficiency with better thermal management type building security light 24/25Watt with integral electronic driver connector block etc. complete with all accessories internally prewired including necessary mounting arrangement, provision of 2 core 1 Sq. mm multistranded copper conductor from ceiling rose to fitting complete all as specified and directed. (3+0+0) Make:- Cat Part No ASTRA LSTS-25-CDL-M of Crompton/ ENXT P 24L WH CR PC SD of Bajaj/ ENDURAPEARLSL25WLED757SASYTOPCMP of Havells.

Taking down ceiling fans of any size/sweep after disconnecting the wire from existing ceiling rose and refixing the same after cleaning dust, oiling, greasing including providing flexible cable from ceiling rose to connector of fan complete all as directed by Engineer-in-Charge (22+0+0)

S&F in repair for MCB DB TPN 4 way double door sheet metal enclosure comprising of OEM/manufacturer specified bus bar 415 volts, 50 Hz bus bar and neutral link complete including inserting in wall complete all as specified. (1+0+0)

S&F in repair MCB triple pole and neutral 415 Volts, 63 Amps, 10 KA. (1+0+0)

S & F in repair 'C' curve MCB SPN 240Volts 40 Amp. (3+0+0)

S&F in repair 'C' curve MCB SP 240 volt 6 to 30 Amp. (9+0+0)

S&F in repair Exhaust Fan with louver, Steel body, size 300 mm, max 410 Watts, minimum 1400 RPM, Single phase, 230 Volts including providing flexible copper cable from the ceiling rose to the connector of fan complete all as directed. (2+0+0)

M&L for plate earthing with galvanised mild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than 2.25 m below normal ground level) with the top edge of the earth plate at a depth not less than 1.5 m below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and incl GI earth wirte 4 mm dia bolted (with GI nuts, bolts & check nuts) and riveted to earth plate at one end and connected to metallic bodies of equipment’s etc at the other end including 15 mm GI light grade protection pipe with all fittings from top of electrode to body of equipment fixed with iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from bottom of earth pit to top of electrode complete with earth pit in PCC 1:2:4 type B-2 using 12 mm graded crushed stone aggregate and RCC cover complete all specified and shown in electrical plate No 3 of SSR Part-1 including testing earth resistance and submitting test report to AGE E/M by the contractor complete all as specified & directed. (2+0+0) Note :- (i) Earthing resistance required in earthing shall less than 3.0 Ohms after completion of work. All earthing shall be tested by the contractor in presence of Engr-in-Charge. Test result shall be recorded and signed by the contractor and Engr – in- Charge. If contractor fail to achieve the above result the same shall be rectified by the contractor without any extra cost to Govt. The earthing result will be required maintaining up to end of defect liability period of one year and if any variation found in earthing result during defect liability period same will be intimated to the contractor by Engg-in-Charge and contractor shall rectify the same. The quoted rates shall be deemed to include for above said provision. (ii) Quoted rates shall be deemed to be included for earth wire with 15 mm dia protection pipe up to 7.5 length.

Note:- The amount against the Schedule of Credit mentioned in the tender document shall be deducted from the total amount quoted against Sch 'A' while deriving the Contract Sum for Acceptance.

Raj Construction

Vee kay construction