Vertical Extension of Mini Cinema Hall with Assam Type Roofing at Assam State Film _Finance and DevelopmentCoorporation ltdPanjabari Guwahati

Amount

18 mm thick Marble stone slab flooring of sizes 1200x1200 including treads and risers of steps, skirting, laid over 20 mm thick base of cement plaster 1:6 (1 cement : 6 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with marble slab of specified quality and shade at all levels.(i) Dungri slab (Green Marble)

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed (for Brick Pillars).(b) In proportion 1:4.(1 cement:4 sand)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately) above Brick Pillars.(a) In prop 1cement: 3 sand :6 coarse aggregate by volume

Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face (for PCC above Brick Pillars).

Supplying, fitting and fixing 38mm thick (finished size) wooden flooring with sal wood plank butt jointed, fitted on sal wood joist of size 100mm x 125mm spaced not more than 900mm apart fitted with 16mm dia bolt and nuts with iron clamp of 50mm x 5mm size inserting in the cement concrete floor base (floor base to be measured and paid separately) including providing 25mm thick damp proof course with water proofing compound as recommended by the manufacturer over C.C floor base including providing kiricide oiling two coats to the timber joists, underside of the flooring planks, two coats of anti-corrosive paint to the iron works, including providing ventilation gaps for the timber works of specified size (75mm x 75mm) covered with welded mesh fabrics at the face of the gap including dressing, levelling, finishing complete as specified and directed by the department at all levels (measurement shall be taken at the finished area of the works).

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) a) Normal range Somany / Orient / Nitco / Varmora / VITA / Marbito Make ii) Of size 600mmx600mm and above

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of J.K Wall Putty (White Cement based putty for concrete/mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Finishing old / new wall with water proofing weather coat smooth anti-fungal premium textured exterior finish of Sandex Matt brand of Snowcem India Ltd. of required shade after clering and clearing the surfaces etc.including scaffolding complete as directed at all levels (two coats).

Supplying, installation testing and commissioning of the following rating copper wound indoor / out door type transformer complete including the payment to be made to power supply authority for supervision charge, labour charge, cost of L.T/H.T metering etc. (excluding the cost of load security) and making necessary arrangement for charging approval of the sub-station from the competent authority as directed and specified by the department. Transformer should be as per CEA guidelines as ammended up to date upto 200 KVA star rating up to 5 star, above 200KVA as per CEA guidelines for losses along with LV enclosure. 250 KVA 33/0.433 KV. Oil filled transformer with Off Circuit tap change.

Supplying including installation, testing and commissioning of Air/Water Cooled Diesel Generator set coupled to suitable alternator of 220/415 V, AC, 1/3-Phase 0.8 p.f. mounted on a 1) M.S. Fabricated base frame.,2) M.S. fuel tank of required capacity.,3) Residual Silencer.,4) AMF Control Panel.5) Suitable batteries with lead.,5) First fill of lube oil.,6) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification.. as per manufacturer. (RANGE FROM 5 KVA TO 625 KV . Kirloskar green/bliss, Leyland, Volvo Penta, Perkinson, Mahindra, Greaves, Escort engine and Kirloskar, Stamford, Leroy somer or equivalent alternator. KVA- PHASE- Approx size- Approx Wt - COOLING 160 3 4040x1450x1900 3550 Kg W/C

Supply & fixing of PAR 64 1000Watt, 240 Volts, Shielded Beam with 2 Mtr, 3 Core wire, 16A plug top & clamp complete in all respect. (Make: Delhi Light / Canara Lighting)

Supply & fixing of PAR 64 1000Watt, 240 Volts, Flood with 2 Mtr, 3 Core wire, 16A plug top & clamp complete in all respect. (Make: Delhi Light / Canara Lighting)

Supply & fixing of Spot Light 1000 Watt, with T-11 type lamp with 2 Mtr, 3 Core wire, 16A plug top & clamp complete in all respect. (Make: Delhi Light / Canara Lighting)

Supply & fixing of 1000W Halogen barndoor flood light consisting of1000W Halogen Bipin T-11 lamp with 2 Mtr, 3 Core wire, 16A plug top & clamp complete in all respect. (Make: Delhi Light / Canara Lighting)

Supply & fixing of 500W Halogen Cyclorama Flood Lights with 500W Halogen tubes. Alluminium anodised reflector, 2nos compressible recessed single contact holders, colour frame & suitable clamp with 2 Mtr, 3 Core wire, 16A plug top & clamp complete in all respect. (Make: Delhi Light / Canara Lighting)

STAGE LIGHT POINT: Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt./ Havells make), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) (note: one end will be terminated to dimmer panel). Extra long point up to 15.00 metre. length.

Extra long point up to 20.00 metre. Length.

Extra long point up to 25.00 metre. Length.

Supply & fixing for Dimmable Auditorium Down Light comprising of 100W PAR Light with diffused reflector in recessed powder coated alumidium die cast fitting with safety wire hooked to the roof structure complete in all respect as directed by the consultant. (Lamp Make: GE/OSRAM/approved equal)

Supply & Fabrication of M.S. Ladders / other necessary support structures etc for the stage area as directed by the consultant including all material, labour, consumables including, Gas, welding rod, primer and synthectic paint etc. complete in all respect as directed by the consultant as approved by the consultant

Supply & fixing of Wall mounted electronic dimmer rack with 12 x 4kW per Channel, electronic dimmers to be distributed in 3 phases with suitable bus bar arrangement as directed by the consultant & complete in all respect. (Make: Delhi Light Model WMD-100 or approved equal in Canara Lighting)

Supply & fixing of 12 Channel DMX Control panel including laying connection cable between the control panel and dimmer rack complete in all respect and as directed by the consultant (make: Codem V- Mix 2000 or approved equal in Canara Lighting)

Supply & fixing of 4 kW Dimmer solution suitable for PAR Lights for ambinece lighting of auditorium complete in all respect as directed by the consultant (make: MK/Phillips/Delhi Light / Canara Lighting)

Supply & fixing of 2 kW Dimmer solution suitable for PAR Lights for ambinece lighting of auditorium complete in all respect as directed by the consultant (make: MK/Phillips/Delhi Light / Canara Lighting)

WIRING FOR AUDITORIUM AMBIENCE LIGHTING: Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Providing and fixing of Rear biparting motorised Main Curtain made out of Velvet curtain cloth (480 to 500 gram in 1 mtr cloth with horizontal sliding arrangement complete with fixing railing track,fixing brackets,runner,master runner,3mm rope wire 1HP Crompton Motor,drum with groove cutting,pulleys,2 No. air breaker switch (L&T,Siemens,GE make) for reverse & forward, 2 No air micro switch for auto stop,3 No push button for Open/Stop/Close position. The curtain should be droped to half area,when in closed position and minimum overlap at the centre should be 900mm and curtain should be stitched in double gathering. (approx size 12000 X 6000) as per design and as directed by the consultant. (Make: Canara Lighting, Delhi Light & Sound).

Providing and fixing PVC Cinema Screen in Matt White having 1.5mm perforation with 6.85% density, which is flame retardant, washable, having eyelets at 200mm, with invisible seam, including cinema screen frame made of MS round pipe duly painted black with tying hooks at every 200mm. The screen will be finished with masking all around made by pasting heavy mill black cloth on 12mm waterproof plywood secured to a rigid ms frame structure. Approx Size incuding the mask is 12000mm x 5500mm. The work to be done as per drawings and as directed by the consultant. (Make: Zoher & Co).

Supply & Fixing of Push Back Auditorium Chairs suitable for installling in 900mm tread, made as per Fire Safety Norms and Standards, with maximum lumbar support for fatigue free healthy seating, engineered for ergonomic shape, environment friendly with no wood used & CFC free, having 25mm x 5mm MS Flatmade back inner frame with 3 serpentine springs, PPCP Plastic molded one-piece inner seat frame, Molded Polyurethane foam cushioned seat back, Uphoistered with Flame Retardant Fabric with Scothgard for Stain Resistance, Zipper attached to seat back fabric for easy removability, epoxy powder coated paint for all steel parts, Integrated skin type PU foam made arm rest without cup holder, Maintenance free Synchornized Push back system, with seamless seat supporting tray, Heavy gauge CRC Sheet made side stand covered with fabric - 4.5 Kg, Back side of the back covered with PPCP Plastic back cover, Chairs installed to the floor with expanded anchor fasteners including accessories like Seat number, Gangways & Aisle light boxes etc complete is all respect as directed and in color shade approved by the consultant (Make: Penworkers/Merryflower

Providing and fixing 2mm Vinyl Flooring Planks to existing levelled floor with SR 988 adhesive. The vinyl shade and design will be approved by the consultant before supply. (Make: Armstrong or approved equal).

Providing & Fixing Step Edge Protection made of Extruded Aluminium Profile duly anodised in approved colour and duly screwed (at 150mm c/c) to the floor concrete using pvc inserts and metal screws. The profile will be Jindal Aluminium 2010 Catalog No 19166 (Width - 57mm; Height - 16m; Thickness - 3mm).

Providing & fixing Led Foot Lights with Seat Nos & Directions including neceaasry wiring on the floor complete in all respect asdirected by the consultant.

Supply, installation, testing & commissioning of Dual 15" High Power Two Way Speaker "Driver Size: LF Driver : 2 x 15"" ,HF Driver : Minimum 1"" Rated Power : Passive/LF - 1,200 W RMS , HF- 75 W RMS Impedance : 4/8 Ohms Maximum SPL Peak(dB) : 135 dB or better Frequency Response : 40 Hz – 18 kHz System Sensitivity : 99 dB Dispersion : 75° H x 50° V Birch Plywood Construction"Approved Makes :Turbosound/Yamaha / QSC

Supply, installation, testing & commissioning of Dual 18" High Power Subwoofer "Driver Size: 2 x 18” LF drivers Rated Power : 1,600 W RMS Impedance : 4 Ohms Maximum SPL Peak (dB) : 137 dB or better Frequency Response : 30 Hz – 200 Hz System Sensitivity : 100 dB 18 mm birch plywood" Approved Makes :Turbosound/Yamaha / QSC

Supply, installation, testing & commissioning of 12000-Watt Dual Channel Power Amplifier with DSP Control and USB Interface "No of Channels: 2 Class-D Maximum Output Power 4 Ω Per Channel : 3200 Watts 8 Ω Per Channel : 1700 Watts Integrated DSP 24-bit/96 kHz converters Distortion <0.2% or better Frequency Response: 20 Hz- 20 kHz Signal-to-noise : >100 dB" Approved Makes : Behringer /Yamaha / QSC

Supply, installation, testing & commissioning of 6000-Watt Dual Channel Power Amplifier with DSP Control and USB Interface "No of Channels: 2 Class-D Maximum Output Power 4 Ω Per Channel : 2800 Watts 8 Ω Per Channel : 1500 Watts Integrated DSP 24-bit/96 kHz converters Distortion <0.2% or better Frequency Response: 20 Hz- 20 kHz Signal-to-noise : >100 dB" Approved Makes : Behringer /Yamaha / QSC

Supply, Installation, Testing and Commissioning of 15,000 Lumens DLP Digital Cinema Projector. DLP technology : 0.98" 2K DMD 3DLP Cinema chip, Brightness : 15,000 Lumens, Resolution : 2048 x 1080 2K, Screen size upto 50 ft (15 m), 3D ready, Number of colours : 35.20 trillion, Lamps : 1.4 KW - 2.3 KW, Standard inputs : 2 x HD - SDI Inputs for 2K source content 2 x DVI (HDMI) inputs, Dimensions : 687 x 665 x 395 mm.

Long Through Lens for the above Projector

Supply & installation of Blue Ray Player of Professional Grade with Dolby Digital output. Approved Make : Denon / Panasonic / Pioneer.

Supply, Installation & Commissioning of Automatic HDMI Switcher for 04 HDMI Input & 01 HDMI Output; Make: Kramer Model: VS41/H as per drawings and as directed by the consultant.

Supply, Installation & Commissioning of Sound Processor & FeedBack Supressor; Make: DBX Model: Driver Rack 260 as per drawings and as directed by the consultant.

Supply, Installation & Commissioning of 32 channel digital mixer . Approved make : Behringer /Yamaha/Soundcraft

Supply, installation, testing & commissioning of UHF Cordless Collar Microphone with Diversity Receiver.Approved Make : Shure / Beyerdynamic/Sennheiser

Supply, installation, testing & commissioning of UHF Cordless Handheld Microphone with Diversity Receiver. Approved Make : Shure / Beyerdynamic/Sennheiser

Supply, installation, testing & commissioning of Dynamic Vocal Microphone with frequency response from 3 khz to 15 khz. Approved Make : Shure / Beyerdynamic/Sennheiser

Supply, installation, testing & commissioning of Stand for Vocal Microphone. Approved Make :Klotz

Supply, installation, testing & commissioning of Gooseneck Microphone fixable to wooden podium with on/off switch. Approved Make : Shure / Beyerdynamic/Sennheiser

Supply, installation, testing & commissioning of Head Phone with connecting cord. Approved Make : Shure / Beyerdynamic/Sennheiser

Supply, Fixing & Commission of all the above equipments as per drawings and as directed by the consultant including the following or any other work required to complete the work to the satisfaction of the consulatant and the department: (a) AV Cables vix., oxygen free speaker cables, HDMI Cables, component cables, composite cables, microphone cables, patch panels, connectors, male-female sockets, adapters, and any other cable/ accessory/ PVC coduit/pipe required to complete the work in all respect as per drawings and as directed by the consultant. Any accessory required to complete the integration of all the above equipments is also inclused in the scope of work (b) Floor Junction Box with XLR connector for microphones.(neutrik Make). (c)Wall Junction Box for Loudspeaker with Phone input connector. (d)Patch Panel as per drawings and as directed by the consultant (e)Suitable Power Termination to all the above equipments from the nearest source provided in the projector room and near the stage (f) Approved Makes: Copper multistrand Speaker cable - Finolex, RR Kabel Snake Cable for Microphone : GOTHAM / Approved Equal Microphone Cable - GOTHAM /Approved Equal Stage Box for Microphone - NEUTRIK / Approved Equal HDMI / Component Cable - Belkin / Approved equal

Supply, installation, testing & commissioning of 10 KVA Servo Controlled Stabilizer as per drawings and as required by the consultant. (Make: Sharp / Venus)

Supply, installation, testing & commissioning of 10 kVA online sine wave UPS with SMF Battery for atleast 15 Minutes Power Backup as per drawings and as required by the consultant. (Make: Better Power/ APC/ Ennov; Battery: Exide/Amaron)

Supply, installation, testing & commissioning of 42U equipment rack as per drawings and as required by the consultant. (Make: APW / PRESIDENT)

Supply, installation, testing & commissioning of Dual 18" Cinema Subwoofer With Dual 700-watt Transducers; Frequency Range Extends To Below 25 Hz When Used With The Correct B6 Filter; Maximum Output 2 Calculated Peak At Rated Power 137 dB; Nominal Impedance 4 ohms; Sensitivity 2 V at 1 Meter, Half Space 101 dB; Maximum Input Power 3(100 hours of 6 dB crest factor IEC 268 noise spectrum) 1200 Watts Continuous.

Supply, installation, testing & commissioning of Surround Left: Surround Loudspeaker System With Directivity Matched Transition™ Provides Balanced Sound Between Woofer And Horn; Rated Noise Power 400 Watts Continuous; Maximum Rated SPL (Calculated Peak At Rated Power) 127.5 dB; Rated Impedance 8 Ohms; Frequency Range (-10 dB, half space) 56 Hz to 20 kHz; Nominal Coverage 90° Axisymmetric.

Supply, installation, testing & commissioning of Surround Right: Surround Loudspeaker System With Directivity Matched Transition™ Provides Balanced Sound Between Woofer And Horn; Rated Noise Power 400 Watts Continuous; Maximum Rated SPL(Calculated Peak At Rated Power) 127.5 dB; Rated Impedance 8 Ohms; Frequency Range (-10 dB, half space) 56 Hz to 20 kHz; Nominal Coverage 90° Axisymmetric.

Supply, installation, testing & commissioning of Surround Rear Left: Surround Loudspeaker System With Directivity Matched Transition™ Provides Balanced Sound Between Woofer And Horn; Rated Noise Power 400 Watts Continuous; Maximum Rated SPL(Calculated Peak At Rated Power) 127.5 dB; Rated Impedance 8 Ohms; Frequency Range (-10 dB, half space) 56 Hz to 20 kHz; Nominal Coverage 90° Axisymmetric.

Supply, installation, testing & commissioning of Surround Rear Right: Surround Loudspeaker System With Directivity Matched Transition™ Provides Balanced Sound Between Woofer And Horn; Rated Noise Power 400 Watts Continuous; Maximum Rated SPL(Calculated Peak At Rated Power) 127.5 dB; Rated Impedance 8 Ohms; Frequency Range (-10 dB, half space) 56 Hz to 20 kHz; Nominal Coverage 90° Axisymmetric.

Supply, installation, testing & commissioning of Digital Cinema Sound Processor, The Processor Accepts Up To Eight PCM Channels From Any Cinema Server, Supporting Access To Optional Hearing- and Visually-impaired Tracks. Three Additional Digital Inputs Accept PCM Or 5.1-channel Dolby Digital from preshow and alternative content sources.

Connectors

Audio Signal Cable;Balanced microphone cable with single shield, high flexible, velvet faint PVC-Jacket , Conductor: Stranded bare copper wires 28 x 0.10 mm (0.22mm²) , Jacket: PVC, 6.0 mm max. Ø

High Flexible Speaker Cable For Power Amplifiers Up To 4000 Watts. 224 Strands Of 0.15 mm Bare Cupper Wires.

19 " Equipment Rack , 42 U , with Heat exaust Fan & Power Distribution box

Servo Stabilizer , 10 KVA , 130-270 Volt - Voltage range

Installation , Programming , Testing & Commissioning cost

Providing & fixing Magnesite bonded wood wool acoustic panel with fibre width of 1mm and size 1200 * 600 * 15mm thickness fixed over a framework of GI frame consisting Of 0.8mm x 50mm th. GI Stud wall channels & floor channels centers filled with 50mm thk fibre glass resin bonded insulation of density 32kg/cum.to be held in position with chicken mesh of 18mm 24SWG. leaving a 50mm airgap. The board shall be covered with FR grade fabric of specified shade or shades shall be stretched on the 15 mm panels using Vinyl Tracks Stretching System. Stretch Perimeter Track half wrap/ full wrap 15 mm and MidSeamTrack 15 mm shall be staple-fixed to the wood wool panels and the fabric is to be fixed on these vinyl tracks.The shade and design of the panelling will be approved by the consultant before supply. (Make: Anutone / Hera Design).

Providing & fixing Acoustical wall paneling using 1.5mm thick Laminate with 12mm thick waterproof termite resistant ply panels secured over GI frame consisting Of 50mm th. GI Stud wall channels & floor channels with filling of 50 mm th. fibreglass resin bonded insulation of density 32kg/cum of UPtwiga.The insulation to be supported from the back by covering the frame with 19mm mesh GI wire netting. (Plywood: Greenply, Mayur, Century; Laminate: Greenlam, Century).

Providing & fixing of black coloured acoustic wood wood wool tiles for back Stage Walls of size 600x600X25mm having a denisity of 400 Kg/M3 directly screwed on 0.8mm thick GI Grid of 50X50mm at 600X1200mm C/c (max) leaving a 50mm air gap between the wall and wood wool panel and finally finished with 2 coats of synthetic enamel paint as per tender drawings and as directed by the consultant for stage and wing area (Make: Hera Design, Himalayan Acoustics, Anutone, Fibercrete).

Providing & fixing of 100mm X 15mm Teak Wood Skirting on bottom and top of wooden wall panelling duly polished with spirit and stain as per drawing and as directed by the consultant.

Providing & fixing of double leaf Accoustic Doors made using 100mm thick hard wood hollow framing filled with 24Kg/M3 desnity fibre glass wool, fixed with 8mm water proof ply wood on both sides, finally pasted with teak vineer on both sides duly polished, consisting of peripheral seals all around on existing 150mm wide Sal chowkhat, with small small 150mm X 150mm glass winodw, with complete hardware including panic bars, steel hinges with ball bearings, latches, pad lock, lock etc complete in all respect and as directed by the Consultant.

Providing & fixing of black coloured Soft Mineral Fibre/Glass Wool Ceiling tiles of size 600x600X20mm with high NRC value greater than 0.9 on a black powder coated GI T grid framework as per tender drawings and as directed by the consultant for main auditorium ceiling (Make: Armstrong/Anutone/AMF).

Providing & fixing of Gysum Ceiling on GI Frame including 3 coats of emulsion paint finish as per IS and as directed by the consultant (Make: India Gypsum / Lafarge).

Providing & fixing of black coloured acoustic wood wood wool tiles of size 600x600X25mm having a denisity of 400 Kg/M3 placed on a black powder coated GI T grid framework as per tender drawings and as directed by the consultant for stage and wing area (Make: Aunotone / Fibrecrete/Himalayan/Heardesign).

Supply and fixing of duct thermal insulation with 13mm thick Armaflex O class nitrile insulation with factory pasted Alum foil on one side pasted on the duct using Dendrite or equiv. adhesive. The insulation seams will be pasted with 50mm wide alum tape and PVC strapping roll strapping will be provided at 600 mm intervals. ( Make: Armaflex , K-Flex, A-Flex).

Supply and fixing of duct accoustic lining inside the ducts with 13mm thick Armaflex O class open cell nitrile sheet pasted on the duct using Dendrite or equiv. adhesive. and harnessed with GI NUT Bolt washer at every 150mm CC. for the first 3 mtr of the duct. as per drawings and as directed by the engineer.( Make: Armaflex, K- Flex, A- Flex)

Providing and fixing of AHU Room wall Insulation with 15mm thick Armaflex O class nitrile opencell insulation with GI Sheed C section grid and finally covered witth 24G Alum Perforated Sheet as per drawings and as directed by the consultant.( Make: Armaflex , K-Flex, A-Flex)

Supply and fixing of Sound Atttenuator in the AHU room for retun air as per drawings and as directed by the consultant.( Make: Airflow Mapro / Ravistar)

Supply , installation , testing and commissioning of Air Cooled Floor Mounted Packaged Air Conditioners suitable to operate from 415+- 10% volt , 50 Hz , 3 phase power supply and consisting of hermitically sealed scroll compressor and having R22 as refrigerant. The scope of work will include copper refrigerant piping with Rajco make 19G hard drawn eddy current tested bright annealed copper pipe,outlet damper, initial gas charging,condensate drain piping, ODU installation on 50 X50X5mm MS Frame(treated with one coat of red oxide and two coats of synthetic enamel paint) , canvas connection , nitrogen flushing , pressure testing and electrical interconnection between IDU and ODU. (Make: Daikin/Bluestar/Voltas) 16.5 Tr Nominal Capacity

phase , having rotary compressor and using R22/R410 as refrigerant and controlling wireless remote. The scope of work includes initial gas charging , refrigerant piping , ODU installation on 50 X50X5mm MS Frame(treated with one coat of red oxide and two coats of synthetic enamel paint) and electrical connectuion between IDU and ODU, connection with insulated drain piping upto nearest drain point complete in all respect. (Make: LG/Voltas/Bluestar/Daikin/Panasonic/Mitsubishi) 2.0 Tr 3 Star Rated

phase , having rotary compressor and using R22/R410 as refrigerant and controlling wireless remote. The scope of work includes initial gas charging , refrigerant piping , ODU installation on 50 X50X5mm MS Frame(treated with one coat of red oxide and two coats of synthetic enamel paint) and electrical connectuion between IDU and ODU, connection with insulated drain piping upto nearest drain point complete in all respect. (Make: LG/Voltas/Bluestar/Daikin/Panasonic/Mitsubishi) 1.5 Tr 3 Star Rated

Supply, installation, testing and balancing of square shape ceiling diffusers with VCD with removable core in extruded aluminium construction with powder coated finish complete in all respect as per drawings ( Make: Mapro Airflow / Dynacraft / Ravistar).

Supply, installation, testing and balancing of Linear Discreet / Continious Grill with 15 Deg Deflecting linear bars in extruded aluminium construction with powder coated finish complete in all respect as per drawings ( Make: Mapro Airflow / Dynacraft / Ravistar).

Supply, installation, testing of multiblade box type Galvanized Sheet Steel construction for duct dampers to be provided with suitable links and quadrants for control of volume of air ( Make: Mapro Airflow / Dynacraft / Ravistar)

Supply and fixing of Galvanised Iron rectangular duct along with all necessary spitters, dampers, supports etc. ( Make: TATA, SAIL). 24G GI Sheet

Supply and fixing of Galvanised Iron rectangular duct along with all necessary spitters, dampers, supports etc. ( Make: TATA, SAIL). 22G GI Sheet

Supplying and fixing Wet Riser Cum Sprinkler Pump:Supply, Installation, Testing & Commissioning of ELECTRIC MOTOR DRIVEN, horizontal split casing, centrifugal fire duty operation pump, coupled through flexible coupling (i/c coupling guard) with totally enclosed, fan cooled squirrel cage 4 pole induction motor suitable for operation on three phase AC supply of 415 + 10% Volts, 50 Hz, fixing the coupled pump and motor on a common structural base frame, making a suitable cement concrete foundation and mounting the complete pump-motor set on the foundation using suitable numbers of anti vibration mountings as per the design / recommendations of the manufacturer and as per the detailed specifications. a) Capacity : 2250 LPM b) Head : 60 meter c) HP : as required. d) No of stages : single e) RPM : 2900 f) Mover : Electric Motor driven. g) Impeller: Bronze h) Shaft: Carbon Steel EN-8 i) Casing : CI j) Bearing : Grease lubricated k) Seal : Mechanical Seal Make: Kirloskar, Mather & Platt, Grundfos, Wilo

Supply ,Installation, Testing & Commissioning of ELECTRIC MOTOR DRIVEN, horizontal end suction type, centrifugal fire duty operation pump, coupled through flexible coupling (i/c coupling guard) with totally enclosed, fan cooled squirrel cage 4 pole induction motor suitable for operation on three phase AC supply of 415 + 10% Volts, 50 Hz, fixing the coupled pump and motor on a common structural base frame, making a suitable cement concrete foundation and mounting the complete pump-motor set on the foundation using suitable numbers of anti vibration mountings as per the design / recommendations of the manufacturer and as per the detailed specifications. a) Capacity : 180 LPM b) Head : 60 meter c) HP : as required. d) No of stages : single e) RPM : 2900 f) Mover : Electric Motor driven. g) Impeller: Bronze h) Shaft: Carbon Steel EN-8 i) Casing : CI j) Bearing : Grease lubricated k) Seal : Mechanical Seal Make: Kirloskar, Mather & Platt, Grundfos, Wilo

Supply ,Installation, Testing & Commissioning of the DIESEL ENGINE DRIVEN, centrifugal, pump & Diesel Engine, complete with all required accessories/systems e.g. couplng guard, fuel service tank , fuel pump, fuel oil filter, Lube oil pump with filter, Electrical batteries, Residential exhaust silencer, exhaust pipe duly cladded with mineral wool & aluminium sheet, engine starting panel having with keys for manual starting etc. fixing the COUPLED PUMP SET and ENGINE on a common structural base frame, making a suitable cement concrete foundation and mounting the complete Engine-pump set on the foundation using suitable number of anti vibration mounts as per the design / recommendations of the of the manufacturer and as per the detailed specifications. a) Capacity : 2250 LPM b) Head : 60 meter c) HP : as required. d) No of stages : single e) RPM : 1800 Maximum f) Mover : Diesel Engine Driven g) Impeller: Bronze h) Shaft: Carbon Steel EN-8 i) Casing : CI j) Bearing : Grease lubricated Make: Kirloskar, Mather & Platt, Grundfos, Wilo

Providing and fixing dust and vermin proof cubical type motor control center for the above panels & cabling with GI Cable Tray as per drawing and as per consultants specification.

Providing and fixing black steel pipes to I.S. 1239 (Heavy class) including all fittings like, couplings, bends, elbows unions, tees, flanges, as per table 'E' reducers, offsets etc., making connections, all type of welded or screwed joints as per specifications and making connections required, including cutting holes and chases in brick or RCC walls and making good complete. After completion of the piping work the entire pipe line will be hydraurically tested for a pressure of 10kg/cm2 for a period of 48 hours. The final pipe line will be painted with two or more coats of synthetic enamel paint of first grade as per IS specifications over one coat of red oxide zinc chromate primer including necessary surface preparation complete. The work will be carried out as per specicfation and drawings and as directed by the consultant. (Make: Tata / Jindal / Nezone) b) 200 mm dia NB

d) 100 mm dia NB

e) 80 mm dia NB

Providing and fixing standard MS Y strainer with flanged ends with SS Perforated filter as per followling sizes complete in all respect. (Sample to be got approved by the engineer-in-charge.) a) 200 mm dia

b) 100 mm Dia

Providing and fixing C.I. horizontal dual plate wafer type non return valves PN 1.6 including washer, nuts, bolts, 1.5 mm thick compressed asbestos gasket companion flanges as per table "E" complete. (Make: Advance / Intervalve / Audco) a) 150 mm dia

c) 80 mm dia.

Providing and fixing double flanged vertical air vessel fabricated from 12 mm MS plate with dished ends 250 mm dia. and 1.25 m high common for fire and jockey and main pumps at drop of pressure as given in the specifications including air release valves complete in all respect.

Providing and fixing MS structural work fabricated from standard sections, eg., MS rounds, angles, channels, inlcuding cutting to size, drilling, welding, fixing and welding to insert plates in RCC structural memebers as directed by the engineer-in-charge including cutting and making good the walls and floors (for Pipe Support Structures & Cable tray.)

Providing and fixing cast iron butterfly valves of PN 1.6 rating complete with bolts, nuts, 3 mm thick compressed asbestos gasket, companion flanges as per table "E" complete in all respects. (Make: Advance / Intervalve / Audco) a) 80 mm dia with lever

b) 100 mm dia with lever

c) 200mm dia with lever

Supplying, Installation, Testing and Commissioning of pressure switches suitable for operating with fire hydrant systems for working pressure of 14.0 Kg/cm² including electrical control wiring with suitable copper conductor PVC insulated and sheathed control cable upto control panel, connections etc. complete as required. (Make: Indfoss)

SITC of Pressure gauge Supply, installation, testing & commissioning of 100 mm dia Bourden type, Stainless Steel dial type glycerine filled pressure gauge including brass isolation valve and pipe having caliberation of 0-16 Kg/cm2. (Make: H Guru / Feibig)

Supply, installation, testing & commissioning of 5(five) Passenger capacity Elevator with all accessories ( including GST & Contractor's profit )Make: Kone or Equivalent

Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Providing SUNROCK HIGH CTS / DEVI paver block / tiles of concrete grade M-30 or above of approved quality, size, shape of specified thickness over a levelling bedding layer of 30 mm compacted sand over a base course of WBM or PCC (Base course to be paid separately) including cutting where necessary finished with spreading, sweeping, jointing sand and compacting the pavers using vibrating compactor as specified and directed. SUN ROCK HIGH CTS / DEVI Tiles (Pavers) (b) 60 mm Thick

Tribeni Constructions Limited