CERTAIN REPAIRS TO FLOORS, WALLS, INTERNAL WATER SUPPLY, ROOF TREATMENT IN ORs AND JCOs MD ACCN AT LGJ MIL STN

Amount

Demolition of cement concrete reinforced of any discription and in any position not otherwise specifically provided complete all as specified and as directed by Engineer-in-charge.

Form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick including edges rough finished complete all as specified & directed by Engineer-in- charge.

Material and labour for mild steel TMT bars 10mm dia and over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for mild steel TMT bars 6 mm to 8mm dia cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for granite slab 20mm thick machine cut, over 15mm screed bed cm (1:4) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and and directed by Engineer-in-Charge.

Material and labour for rounding to edge of granite slab in cooking platform and other similar situation including grinding and polishing complete all as specified and and directed by Engineer-in-Charge.

Supply and fixing in repair stainless steel kitchen sink without drain board, made out of 1.00mm thick sheet for kitchen with washers, waste coupling and waste pipe overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engineer-in-Charge. Make : Prayag

Supply and fixing in repair stainless steel kitchen sink with drain board, made out of 1.00mm thick sheet for kitchen with washers, waste coupling and waste pipe overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engineer-in-Charge. Make : Prayag

Supply & fixing in replacement stainless steel kitchen plate rack made out with 1mm thick sheet of size 24" x24" x 10" including taking down existing wooden plate rack complete all as specified and directed by Engineer-in-Charge. Make-Prayag, Cat Part No-310

Material and labour for rendering/plastering 10mm thick in cement mortar (1:4) on concrete surfaces of ceiling, finished fair and even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparing newly plastered undecorated surface of ceiling by sand papering or by any other mean and after preparing the surfaces applying three coats of white wash complete all as specified & directed by Engineer-in- charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each and removing from site complete all as specified and as directed by Engineer-in- charge.

Taking down any type of shutters only of any description area exceeding 1 sqm and not exceeding 2 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs etc complete all as specified and as directed by Engineer-in- charge.

S&F factory made steel ventilator with half portion fixed type and half top portion top hung shutter including box type hinges, steel peg stay with glazing bar, fixing lugs in PCC(1:2:4) type B-1 complete all as specified and directed by Engineer-in- charge.

Supply & fixing, 4mm thick figured glass ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in- charge.

Supply & fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tack or stainless steel wire staples complete all as specified & directed by Engineer-in- charge

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint complete all as specified & directed by Engineer-in- charge.

S&F in repairs 25mm dia mild steel pipe coated with PVC sheet as in drapery curtain rod with decorative end knobs complete with brackets and fixed on wall complete all as specified and directed by Engineer-in- charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new plain glass one complete all as specified and as direc by Engr-in-Charge.

Supply & fixing in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tack or stainless steel wire staples or wooden beeding complete all as specified & directed by Engineer-in-Charge

Dismantling of brick tiles laid flat or on edge in floor and pointing in cement mortar of any discription including removing rubbish material from the site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 40mm thick brick tiles laid on lime concrete & joints grouted flush pointed in cement mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed by Engineer-in-Charge.

,---Ditto-- All as per Srl item no. 22 above, but except brick tiles complete all as specified and directed by Engineer-in-Charge.

M&L for raking out joints / pointing to brick work in roofs, including cleaning the roof surface complete all as specified and directed by Engineer-in-charge.

M&L for flush pointing in cement mortar (1:3) mixed with 5% of crude oil by weight of cementto brick tiles on roof complete all as specified and directed by Engineer-in-Charge.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-neck etc complete all as specified and directed by Engineer-in-Charge.

Supply & fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints and fixed to wall complete all as specified & directed by Engineer-in- Charge.

Supply & fixing PVC (SWR) bend any radius 110mm bore complete all as specified & directed by Engineer-in- charge.

S&F in repair stack clamps for 110mm bore PVC pipes made out of 50mm x 5mm FI Clamp and fixed with 150mm long screws with fastener and securing ends to wall complete all as specified & directed by Engineer-in-Charge.

Taking up or down existing galvanised steel water tubing (GI pipe) 15mm bore including fitting/connection from wall/ceiling/floor etc. including cleaning for reuse or removing complete all as specified and as directed by Engineer-in-charge.

Supply and fixing galvanized steel tubing medium grade 15mm bore with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor complete all as specified and as directed by Engineer-in-charge.

Taking up or down existing galvanised steel water tubing (GI pipe) 20mm bore including fitting/connection from wall/ceiling/floor etc. including cleaning for reuse or removing complete all as specified and as directed by Engineer-in-charge.

Supply and fixing galvanized steel tubing medium grade 20mm bore with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor complete all as specified and as directed by Engineer-in-charge.

Supply & fixing in repair rotational moulded polyethylene water storage tank (cylindrical vertical tripple layered with closed top), ISI marked, hoisted and fixed in position of capacity 500 litres including out let connection including dismantling/taking down of existing unserviceable PVC water storage tanks of any description, any capacity complete all as specified & directed by Engineer-in-charge.

Supply and fixing 20mm ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density polythene float and fly-nut complete, screwed for iron pipe or brass ferrule, suitable for 20mm bore pipe complete all specified and as directed. Note :- The minimum weight of ball valve shall be as given in SSR or in relevant IS.

Supply and fixing in repair 20mm ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density polythene float and fly-nut complete, screwed for iron pipe or brass ferrule, suitable for 20mm bore pipe complete all specified and as directed. Note :- The minimum weight of ball valve shall be as given in SSR or in relevant IS.

Supply and fixing in repair 15mm gun metal, globe or gate valve (ISI marked), brass cast copper allow, with iron wheel head, screwed both ends suitable for 15mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS.

Supply and fixing in repair 20mm gun metal, globe or gate valve (ISI marked), brass cast copper allow, with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS.

Supply and fixing in repair 32mm PVC waste pipe for wash basin complete all as specified and as directed by the Engineer-in-Charge.

Supply & fixing in replacement pillar tap swan neck fancy type, cast copper alloy with capstan head, chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long screwed shank and fly nuts, screwed for iron pipe 15mm bore complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant.

Supply and fixing in replacement 450mm long PVC connection 15mm size with PTMT nuts complete all as specified and as directed by Engineer-in-charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided including removing rubbish material from the site complete all as specified and as directed by Engineer-in-charge.

Taking down cement plaster of any description from brick walls or concrete surfaces of walls and ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L for Water proofing treatment to RCC sunken slab as specified below and as directed by Engineer-in-Charge. :- (a) applying 15 mm plaster in CM 1:3 with WPC on verticle and horizontal surface (b) Cleaning the surface with wire brush/coir brush, removing lose material like dust particles, dirt etc. (c) Creating fillet coving of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and verticle surface (e) Provision of glass fiber mesh of 2 x 2 mm of GSM 145 immediately on above coating (f) Apply second coat of two component modified polymer coating after 72 hrs (h) Joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5 mm (j) Filling the gap between the wall opening and saintary pipe with non shrink cementatious grout complete as specified Make:- Dr. Fixit/Fosroc/STP Note: (i) The treatment shall be carried out by approved authorised applicator as per the manufacturers instructions and as directed by the Engineer in charge. (ii) The Plan area of floor shall be considered for payment and provn of cement work PCC is included in quoted rate for this item.

Supply and fixing in repair Indian type water closet 'orrisa pattern' Size 445 x 585 x 260mm with ' P ' trap 220mm complete all as specified and directed by Engineer-in-Charge. Note : Colour shall be decided by Engineer-in-Charge.

Supply and fixing in repair 10 litres capacity PVC valveless syphonic action type, low level flushing cistern, white with inlet, ball valve, float, handle including brackets and 32mm dia PVC flush pipe, PVC Connection 600 mm long with PTMT nuts suitable for 15mm bore pipe including taking down old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 100mm dia cast iron soil waste pipe in any length with or without ears with cement joints laid in trenches or floors or walls including taking down old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 100mm dia cast iron ' P " trap including taking out old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 100mm dia cast iron ' Bend " including taking out old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 100mm dia cast iron ' Heel rest bend or ducks foot" including taking out old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 100mm dia cast iron ' Branch piece Y shape or T shape " including taking out old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 100mm dia cast iron 'Cowl " including taking out old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 100mm dia ' Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays " including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 75mm dia cast iron soil waste pipe in any length with or without ears with cement joints laid in trenches or floors or walls including taking down old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 75mm dia cast iron ' floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) taking out old one complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 75mm dia cast iron ' Bend " including taking out old one complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 75mm dia cast iron ' Heel rest bend or ducks foot" including taking out old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 75mm dia cast iron ' Branch piece Y shape or T shape " including taking out old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 75mm dia cast iron 'Cowl " including taking out old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair 75mm dia ' Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays " including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Material and labour for Non Skid ceramic coloured tiles (jointless) 7 to 8 mm thick square or rectangular area of each tile (300 x300 mm) exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles 300mm x 450mm x 7mm thick as in vertical surface such as skirting, dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair fancy type chromium plated bib tap, cast copper alloy, with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferrule & fixed suitable for 15mm bore iron pipe complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS

Supply & fixing in repair Angle cock cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe suitable for size 15mm bore complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve shall be as given in SSR or in relevant IS.

Supply & fixing in replacement stop valve fancy type, cast copper alloy, chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union, size 15mm bore complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve shall be as given in SSR or in relevant IS. Make : Prayag, Model for concealed stop cock No:TRANQUIL-Code no-7318

S & F in Replacement of brass spindle for 15mm concield stop cock in bath room complete, all as specified & directed by Engineer-in-charge.

S & F in Replacement of brass spindle for 15mm bib cock in bath room, toilet, kitchen complete, all as specified & directed by Engineer-in-charge.

S & F in Replacement of chromium plated waste coupling for kitchen sink complete, all as specified & directed by Engineer-in-charge.

Material and labour for rendering/plastering 15mm thick in cement mortar (1:6) on any fair face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of wall surfaces/putty surfaces by sand paper with mechinical method i.e. Hand electric grinder and applying two coats of oil bound distemper over one coat of cement primer inclusive all as specified with mechinical method i.e. spray gun etc, complete all as specified & directed by Engineer-in-charge.

M&L removal of old treatment of wall and preparation of surface, application of two coatsof interior grade wall care putty and preparation for preparation of wall surfaces/putty surfaces by sand paper with mechinical method i.e. Hand electric grinder and applying two coats of oil bound distemper over one coat of cement primer inclusive all as specified with mechinical method i.e. spray gun etc, complete all as specified & directed by Engineer-in-charge.

Material and labour for rendering/plastering 15mm thick in cement mortar (1:4) on any fair face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered / old plastered or pointed surface of walls/pillars/cornices by sand papering or by any other mean and after preparing the surfaces applying two coats of cement base paint over a coat of alkali resistant primer as approved tint/colour over a one coat of priming paint complete all as specified and as directed by Engineer-in-Charge.

M & L for broken bricks bats hardcore of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer-in-charge.

M & L for 50 mm thick sub base of cement concrete type B-1, 1:2:4 ( 20mm graded aggregate) complete all as specified and directed by Engr-in-charge.

Dismantling asbestos cement (corrugated / semi corrugated) sheets including ridges as in roof covering all as specified & directed by Engineer-in-Charge.

Material and labour for 6mm thick asbestos cement (corrugated / semi corrugated) sheets in roof, walls are fixed with L-type or J-type cranked hook bolts complete all as specified & directed by Engineer-in-Charge.

Fixing only for 6mm thick asbestos cement (corrugated / semi corrugated) sheets in roof, walls are fixed with L-type or J type cranked hook bolts complete all as specified & directed by Engineer-in-Charge.

Material and labour for 6mm thick asbestos cement serrated ridge are fixed with L-type or J type cranked hook bolts as in repair complete all as specified & directed by Engineer-in-Charge.

M&L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specifiedcomplete all as specified & directed by Engineer-in-Charge.

M&LPre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified & directed by Engineer-in-Charge.

Dismantling of mild steel wind tie complete all as specified & directed by Engineer-in-Charge.

Fixing only for mild steel wind tie are fixed with L-type or J type cranked hook bolts complete all as specified & directed by Engineer-in-Charge.

Supply and Fixing for mild steel wind tie are fixed with L-type or J type cranked hook bolts complete all as specified & directed by Engineer-in-Charge.

Dismantling of brickwork or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge.

Material and labour for brick work in full brick thick wall using Fly Ash bricks (old size bricks) straight or curved on plan to any radius built in cement mortar (1:6) complete all as specified & directed by Engineer-in- charge.

Supply & fixing in repair rotational moulded polyethylene water storage tank (cylindrical vertical tripple layered with closed top), ISI marked, hoisted and fixed in position of capacity 1000 litres including out let connection including dismantling/taking down of existing unserviceable PVC water storage tanks of any description, any capacity complete all as specified & directed by Engineer-in-charge.

Supply & fixing in replacement brass chromium plated 4" Multi flow overhead shower with 225mm arm & flange including fixing to 15mm bore pipe complete all as specified and as directed by Engineer-in-charge.

M&L for applying two coats of oil bound distemper over a coat of chalk whiting primer on a prepared surface complete all as specified & directed by Engineer-in-Charge.

Supply and fixing in replacement bib tap 2 way double handle with flange, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferrule & fixed suitable for 15mm bore iron pipe complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS. Make-Prayag, Model No:TRANQUIL-Code no-7312

Supply and fixing in repair chromium plated fancy type toilet paper holder complete all as specified and directed by Engineer-in-Charge. Make-Prayag, Model no-CANTABILE-SAGA -Cat no-BA-38

Supply and fixing in repair chromium plated fancy type soap dish complete all as specified and directed by Engineer-in-Charge.(Make-Prayag) Model no-CANTABILE-PICASSO -Cat no-BA-05

Supply and fixing in replacement PVC grating round or square 150mm size (minimum weight 100gms) complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing in repair 75mm dia cast iron ' door Bend " including taking out old complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair pedestal type water closet with seat cover complete all as specified and directed by Engineer-in-Charge. Note : Colour shall be decided by Engr-in-Charge.

Supply and fixing in repair vitreous china half stall urinal type including waste pipe with chromium plated coupling complete all as specified and directed by Engineer-in-Charge. Note : Colour shall be decided by Engr-in-Charge.

Supply and fixing in repair vitreous china wash hand basin (flat back or angle back type) size 550 x400 mm including cutting for and pinning in ends of brackets or erecting stand and also including waste pipe with chromium plated coupling complete all as specified and directed by Engineer-in-Charge. Note : Colour shall be decided by Engr-in-Charge.

Material and labour for 40mm thick PCC (1:2:4), type B-1 using 20 mm graded stone aggregate as in floor finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

Material and labour for machine cut 20-25 mm thick, Kota stone slab as in floors, stair steps, skirting, dado and on pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, including 15 mm thick screed bedding layer in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed by Engineer-in-Charge.

S&F Dark shade virified ceramic tiles 10mm thick dark shade (square/rectangular) polished area of each tile is 0.36 sqm, in floors,walls etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layers in CM 1:4.complete all as specified & directed by Engineer-in-Charge.

S&F light shade virified ceramic tiles 10mm thick dark shade (square/rectangular) polished area of each tile is 0.36 sqm, in floors,walls etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layers in CM 1:4.complete all as specified & directed by Engineer-in-Charge.

Demolition of AC plain ceiling board in any thickness including complete all as directed by Engineer-in-Charge.

Material and labour for 4mm thick asbestos cement plain building boards fixed to timber frame work or MS frame work as in false ceiling fixed with screws incl white wash complete all as specified & directed by Engineer-in- charge.

S&F armstrong mineral fiber accoustical suspended ceiling system with ANF(Micro look) EGE tiles with arm strong silhouette exposed grid. The tiles should have humidity resistance (RH) of 90%. NRC 0.5%. Light reflectance shall be more than 85% thermal conductivity K=0.052-0.057 w/mk. colour shall be white, fire perfomance class 0/class 1 (BS 4760 in module size of 600mmx600mmx15mm with bioblock coating on the face of tiles, suitable for green building application with recycle content of 63% the tiles shall be laid on arm strong silhouette profile grid system with 15mm with flanges incorporating 6mm central revel in white/black colour and with a web height of 45mm and and load carrying capacity of minimum 15.68kg/sqm.silhouette , main runner and cross runner shall have mitred end and birdsmouth notches to provides mitred juction. the Tee section hace a galvanised of 125gms/sqm complete all as specified and directed by Engineer-in-charge.

Repair the existing wooden shutters area exceeding 1 sqm and not exceeding 2 sqm each including taking down, refixing, after the necessary easing, adjustments, minor repairs etc with proper working condition all as specified and as directed by Engineer-in- charge.

Repair the existing aluminium single shutters or double shutters including taking down, refixing, after the necessary adjustments, minor repairs and greesing the floor spring etc with proper working condition all as specified and as directed by Engineer-in- charge.

Repair the existing PVC door and FRP shutters area exceeding 1 sqm and not exceeding 2 sqm each including taking down, refixing, after the necessary easing, adjustments, minor repairs etc with proper working condition all as specified and as directed by Engineer-in- charge.

Supply and fixing in repair 375mm mild steel ordinary rat tail rod pattern spring including roller and roller plate and welding to frame as required complete all as specified and as directed by Engineer-in- charge.

Supply only 100mm long butt hinges mild steel medium weight cold rolled including necessary welding etc. to steeel frame complete all as specified & directed by Engineer-in-charge.

Supply & fixing 100mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised type B-21 and fixed complete all as specified and as directed by Engineer-in-charge. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

ISHAAN CONSTRUCTIONS

M/s Karan Builders

NATIONAL ENTERPRISES

ram rattan dass aggarwal

Aggarwal brothers and company

KHANNA CONSTRUCTIONS