REPAIR/MAINT TO ROOF SHEET, ROOF TREATMENT, JOINERY, FLOORING, FALSE CEILING, INTERLOCKING TILES, BOUNDARY WALL AND MISC B/R WORKS AT VARIOUS E/M INSTALLATIONS BLDGS AT CH (CC) AND OFFICE COMPLEX OF GE E/M OFFICE UNDER GE E/M LUCKNOW

Amount

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stone work and pre cast concrete articles complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level), complete all as specified and directed.

M&L for brick work with fly ash bricks as per IS 12894 -2002 straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and directed.

M&L TMT 10mm dia and over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming Fe- 500, complete all as specified and directed.

PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in coping, chajja, facia and the like including weathering, slightly rounded or chamfered angles with & incl necessary use and waste of form work for fair faces of concrete, complete all as specified and directed.

Supply only integral water proofing compound powder conforming to IS specification, complete all as specified and directed.

Mild steel work Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 as in small articles like angle iron framing work for manhole, rungs/steps in man hole, complete all as specified and directed.

Treating small articles of steel like MS rungs etc with coal tar black paint including preparation of surface, area tarred not exc 0.1 sqm, complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and directed.

M & L for Super heavy series PVC Wall panelling/Lining consisting of 5mm thick Plain/wood colour PVC sheet as approved inclusive of solvent cement and fixing at site on PVC frame including complete fixing arrangments on wall complete all as per manufactures specifications, complete all as specified and directed.

Providing and fixing of E-board 'Everest' make 600x600x4mm thick white prelaminated seif embosed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24 mm wide T-section/Angle section, complete all as specified and directed.

M&L Suspended ceiling, comprising 12.5 mm thick reinforced gypsum plaster boards Conforming to IS-2095 , including compele fixing arragements as per manufactures instructions including finishing the exposed surfaces with Oil bound distemper two coats over 2mm thick wall care putty complete all as specified and directed.

Taking down chowkhats or frame (wooden/aluminium/iron) n. exc. 1.5 Sqm each with shutters (with out taking off shutters from the frame) and taken as credit complete all as specified and directed.

Taking down chowkhats or frames (wooden/aluminium/iron) with shutters without taking off shutter from the frames exc. 1.5 but n. exc 4 sqm each complete all as specified and directed.

Taking down shutters of any description n exc 1 sq.m each complete all as specified and directed.

Taking down shutters of any description exc 1 sq.m and n exc 2 sq.m each complete all as specified and directed.

PVC door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with MS square tube, suppling & fixing in opening complete all as specified and directed.

S &F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm with stuck inside with, complete all as specified and directed.

S&F 250 mm aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 100 mm length of bolt complete all as specified and directed.

S&F 75mm size butt hinges medium weight (ISI Marked), rolled mild steel complete all as specified and directed.

S&F 125mm size Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery complete all as specified and directed.

S & F in repair for 150 mm floor door stopper of aluminium alloy body and tonge,anodised with hard drawn steel spring, complete all as specified and directed.

Hacking out old broken glass, any thickness, size, quality, or description, from frame nexc 1.5 Sqm each pane, complete all as specified and directed.

S&F for 3.0 mm thick sheet glass ordinary quality and glazing with oil putty/wooden beading/aluminium beading nexc 0.5 Sqm each pane, complete all as specified and directed.

S&F for 3.0 mm thick figured glass ordinary quality and glazing with oil putty/wooden beading/aluminium beading nexc 0.5 Sqm each pane, complete all as specified and directed.

S&f for 4.8 mm thick sheet glass odinary qulity and glazing with oil putty/wooden beading/aluminium beading exc 0.5 Sqm each pane, complete all as specified and directed.

S&F in repairs Chromium plated fancy long body Bib taps with cup, cast copper alloy with crutch handle, screwed for 15 mm bore dia. iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs Brass chromium plated shower rose without swivel joints , any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs Chromium plated ,Concealed stop cock Reduced body ISI Marked, , cast copper alloy, screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed.

S&F in repair CP Angle stop cock ( one way) long thread with wall flange , fancy type screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed.

S&F in repairs Pillar taps, fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe, complete all as specified and directed.

S&F in repairs CP Angle stop cock( two way) long thread with wall flange , screwed down for 15 mm bore dia. pipe, high pressure, with crutch handle , screwed externally both ends for unions etc. and fixed complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S&F in repairs for 15mm bore pipe Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed, complete all as specified and directed.

S&F in repairs CP mild steel gratings suitable for 75/100 mm dia NT/ FT complete all as specified and directed.

S&F in repairs Chromium plated Brass Tubular towel rod, of 24" (60 cm long) complete all as specified and directed.

S&F in repair vitreous China wash down water closet pan ( padestal pattern Water Closet ) , including fixing bolts, flush pipe , including connection to drain ( or outgoing pipe) and to flushing pipe, etc, complete including make good the floor as existing, complete all as specified and directed.

S&F in repairs VC WHITE Squatting pan ,'Orissa' pattern size 580x440mm with integral footrests water closet) with 'P' or 'S' trap front or back inlet complete including lime concrete for bedding, connection to drain pipe and to flushing pipe , anti syphon complete including make good the floor as existing, complete all as specified and directed.

S&F in repairs Low level flushing cistern, moulded from virgin poly propylene complete all as specified and directed.

Supply and fixing in repairs Plastic water closet seat, white, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs PTMT connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S & F in repair for Large standard urinal of make- Hindware/cera/Jaquar with complete fixing arragment, waster pipe, coupling, urinal spreader etc complete all as specified and directed.

S&F in repair vitreous china wash basin (WHB) , white , flat back , size 550mmx400mm including brackets, waste fittings , brass Chromium plated for glazed basins etc. with long screw shanks and fly nuts , flange end embedded in red lead cement , including cutting, complete all as specified and directed.

S&F 32mm bore flexible pipe of PVC fixed to WHB/ urinals as waste pipe ( not less than 600mm) including PVC coupling complete all as specified and directed.

S&F in repair Gun metal , globe or gate valves, with iron wheel head, screwed both ends for 20 mm bore dia. iron pipe and fixed complete all as specified and directed.

S&F Gun metal, in repair globe or gate valves, with iron wheel head, screwed both ends for 15 mm bore dia. iron pipe and fixed complete all as specified and directed.

S&F in repairs Aluminium body ( extruded section ) body Door closer hydraulically regulated, designation No. 2 , universal type , suitable for door shutters 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed, complete all as specified and directed.

S&F in repair for 100 mm mild steel 4 lever mortice lock vertical type of size of brass body, complete all as specified and directed.

S&F Anodised aluminium frame for doors, windows, ventilators, partition section with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S &F aluminium anodised partition with 3mm thick aluminium composite panel at bottom panel and 4 mm thick glass on top panel incl glazing clip and neosprene rubber beading with section weight minimum 0.55 Kg/m complete all as as specified and directed including dismantling of old unserviceable aluminium partition, complete all as specified and directed.

S &F in repair 3mm thick aluminium composite panel with glazing clip and neosprene rubber beading complete all as specified and directed.

S&F in repair Aluminium grill not less than 3.13 Kg per sqm fixed with frame in windows/ventilator at site complete all as specified and directed.

S&F Anodised Aluminium alloy sections sliding windows shutters with frames comprising Series -C (20mm), 3 track sliding shutters duly fitted with neoprene beading, glazing clips,locking device, heat absorbing glass 4.8 mm nominal thicknes in 2 shutters and 0.46mm dia SS wiremesh in one shutter complete all as specified and directed.

S&F aluminium sections ( conforming to IS) door with frame of size 100mmx 44.45mm wide fabricated with 2mm thick section , double/single leaf shutter with 44.45mm wide fabricated with 2mm thick section having vertical and top rail 83.50mm, bottom rail and middle rail 115mm and including necessary jointing cleats, screws, neosprene rubber beading, PVC packing, tinted glass panes 4.8 mm nominal thickness, 100mm butt hinges (3 Nos in each panel), 150mm tower bolt (1 in each panel), locking arrangements with 100 mortice lock complete all as specified and directed.

S & F in repair stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.23(b) complete all as specified and directed.

S&F 100mm size butt hinges medium weight (ISI Marked), rolled mild steel complete all as specified and directed.

S&F in repair 100mm size butt hinges medium weight (ISI Marked), rolled mild steel complete all as specified and directed.

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 20mm thick in cement mortor 1:4, complete all as specified and directed.

Dismantling floor, stone flooring, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises, complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surfaces 350 x 250 x 7 mm / 450 x 350 x 7 mm [thick] set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over and including 10mm thick screed in CM 1:3, complete all as specified and directed.

M&L for non skid ceramic tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over and including 15mm thick screed in CM 1:6 complete all as specified and directed.

M&L Vitrified ceramic tiles 10mm thick (square/ractangular) Coloured polished tiles, area of each tile n.exc 0.38 sq m in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement and pigment to match over and including 15 mm thick screeding in CM 1:6 complete all as specified and directed.

S & F in repair 20 mm dia fancy type drapery curtain rod made of mild steel duly PVC sleeved complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 as in sub base, foundation and mass concrete using 40 mm graded stone, complete all as specified and directed.

Dismantling of roof sheet (any descriptions) including ridges in roof covering complete all as specified and directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated/plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for providing cement concrete type B-1, 1:2:4 (20 mm graded aggregate ) as in roof kerbs /padding or similar work or mud stops rounded or chamferred on edges, complete all as specified and directed.

M&L 6-10mm thick exterior wall tiles (digital pattern) of area of each tiles not exceeding 0.18 sqm as in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 10mm thick rendering in CM 1:3, complete all as specified and directed.

Taking down cement plaster on brick wall, racking out joints hacking for key scrubbing down with water complete all as specified and directed.

15mm thick rendering on brick work or concrete surfaces in CM 1:4 finished fair & even without extra cement, cement mortar mixed with WPC @ 3% of weight of cement, complete all as specified and directed. (Note: WPC measured & paid for separately)

M&L for rendering 10 mm thick on brick work/ concrete surfaces in cement mortar 1:6 on fair faces finished fair & even, complete all as specified and directed.

M&L rendering 5 mm thick on concrete surfaces in ceiling , in cement and sand mortar 1:3 complete all as specified and directed.

M&L for preparing surfaces, plastered or unplastered new surfaces of ceiling and applying three coats white wash complete all as specified and directed.

Preparation of newly plastered surfaces and applying two coat of oil bound disemper over one coat of oil base primer all as specified on walls surface.Incl a coat of 3mm wall care putty, complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint of any tint/shade over a coat of primer complete all as specified and directed.

M&L applying two coats of Apex ( Asian Paint) / Weather coat (Berger) over newly plastered surface including preparation of wall surface over and including 1mm thick wall care putty complete all as specified and directed.

Preparation of new wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new steel and iron based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including knotting and stopping and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, and applying one coat of cement base paint of any tint/shade complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

M & L for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates (Grade Fe- 290 (Gde E- 165) complete all as specified and directed.

M & L for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as plinth protection/path and the like complete all as specified and directed.

M&L 18-20mm thick machine cut Kota stone slab flooring with marble stone strips/ slab/ tiles as per design approved, over and including cement screed bed 20mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing complete all as specified and directed.

M&L 18-20mm thick machine cut Kota stone slab as in skirting /riser over and including cement screed bed 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing complete all as specified and directed.

Grinding of old kota stone flooring upto mirror finish level including polisihig etc complete all as specified and directed.

S & F Powder coated brackets for fixing curtain rod of any dia and fixed complete all as specified and directed.

S & F in repair for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and directed. (Note:- Each line wire to be measured including dismantling of old wire)

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including dismantling and removal of existing paver blocks, complete all as specified and directed.

M&L for exterior grade outdoor coloured floor tiles (heavy duty) of tactileseries of size 300x300x10mm of Make Johnson endura or equivalent make bedded over and including 20mm thick screed bed in CM 1:6 and jointed in cement mortar to match the colour of floor complete all as specified and directed including dismantling of existing tiles, complete all as specified and directed.

Demolition of existing roof treatment of any type, complete all as specified and directed.

M & L 15mm thick screed plaster on RCC slab CM 1:4 with using water proofing compound @ 3% by weight of cement, complete all as specified and directed. (Note:- WPC to be measured and paid separately)

M & L for water proofing treatment on roof surfaces in the following manner:- (a) The surfaces shall be painted with hot bitumen grade 30/40 confirming to IS-73 @ 1.20 kg/sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 ltr/sqm. (b) supply & lay 3 mm thick APP water proofing membrane reinforced with non woven polyster matt laid using butane torch by torch on application with a side lap of 10 cm & 15 cm end lap weinghing not less than 3.5 kg/sqm. (c) Applying one coat of aluminium paint including preparation of surfaces and primer

Taking up or down steel tubing and connections , including cleaning for re-fixing or removal of store, 15 mm bore complete all as specified and directed.

Taking up or down steel tubing and connections , including cleaning for re-fixing or removal of store, 20 mm bore complete all as specified and directed.

M&L 15 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L 20 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Taking down existing PVC water tank capacity exc 250 & n.exc 500 ltr and S&F Rotational moulded polyethylene water storage tanks three layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt I. capacity of tank 500 litres complete all as specified and directed.

S &F in repair 110mm bore (SWR) pipe single socketed in any length with rubber ring joints, laid in floor or fixed to walls, complete all as specified and directed.

All as per item No 107 above but dia of 75mm

S&F 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend of any radius, complete all as specified and directed.

All as per item No 110 above but dia of 75mm

M/S Reliance Construction

M K Engineers and Contractors

M/s Bipin Construction

M/S SWATI CONSTRUCTION

NEW BHARAT ENGINEERING AND CONSTRUCTION CO

M/S AMARJIT SINGH

JITENDRA SINGH

MAA BHAWANI CONSTRUCTION

Total Construction & Management Services