REPAIR MAINT OF WOODEN STEEL FURNITURE INCLUDING POLISHING AND OTHER CONNECTED WORKS AT AIR FORCE STATION UDHAMPUR

Amount

WOODEN FURNITURE : Taking down worned out components of the following furniture items and S&F new component without having any defect as per shape and size as specified and shown on respective drawings and as directed by Engineer-in-charge

BED plywood TOP WOODEN (FD 246)

Head rest complete

Foot Rest complete

Long rail

Short rail

Stiffener

Right angled MS bracket 200mm long x 25mm wide x 3mm thick duly fixed with screw

12mm thick BWR plywood top in one piece

CHAIR DINING (FD-279)

Rear Leg

Front Leg

Side rail with holes for weaving (spacing of holes shall be as per old one)

Front/back rail with holes for weaving (spacing of holes shall be as per old one)

Bottom stiffener

Back stiffener

Provn of wooden Triangular bracket of size 75mm x 75mm x25mm at joint of leg and rail each chair made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

CHAIR WRITING (FD-280)

Rear legs

Front Legs

Side rail with holes for weaving (spacing of holes shall be as per old one)

Front/back rail with holes for weaving (spacing of holes shall be as per old one)

Bottom stiffener

Back stiffener

Arm rest

Provn of wooden Triangular bracket of size 75x75x25mm at joint of leg and rail of chair made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

CHAIR DINING OFFICERS (FD/MAP-II/04)

Rear Leg

Front Legs

Side rail of seat frame

Front/back rails of seat frame

Seat made out of 75mm foam cushioned of 40 density covered with fabric as approved by Engr-in-Charge fixed on12mm thick plywood.

Bottom stiffener

Vertical back stiffener

Provn of wooden Triangular bracket of size 75x75x25mm at joint of leg and rail of chair made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

CHAIR EASY(FD-229)

Rear Leg

Front Leg

Side Rail

Front/Back Rail

Back Stiffener

Bottom Stiffner

Arms rest

PVC/Rubber Shoe as per sample approved

TEAPOY (FD-278/382)

Long rail

Short rail

Side stiffener

Centre stiffener

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

PVC/Rubber Shoe as per sample approved

Provn of wooden Triangular bracket of size 75x75x30mm at joint of leg and rail of teapoy made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PEG TABLE (FD-/277/384)

Long rail

Short rail

Side stiffener

Provn of wooden Triangular bracket of size 75x75x20mm at joint of leg and rail of peg table made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

PVC/Rubber Shoe as per sample approved

PEG TABLE MAP, (FD/E6/MAP/11)

Long rail

Short rail

Side stiffener

Provn of wooden Triangular bracket of size 75x75x20mm at joint of leg and rail of peg table made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

PVC/Rubber Shoe as per sample approved

Table writing (FD-275)

Long rail

Short rail

Bottom centre stiffener

Bottom side stiffener.

Side of the box out of 18mm thick MDF board

Back of the box out of 6mm thick one side teak face commercial plywood

Provn of wooden Triangular bracket of size 75x75x25mm at joint of leg and rail of table made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

PVC/Rubber Shoe as per sample approved

TABLE 900mm x 600mm WITH DRAWER (FD-283)

Long Rail

Short Rail

Bottom Side stiffener

Bottom Centre stiffener

Drawer as specified in drawing

Provn of wooden Triangular bracket of size 75x75x25mm at joint of leg and rail of table made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

PVC/Rubber Shoe as per sample approved

TABLE DINING 06 PERSON( FD-273)

Long rail

Short rail

Stiffener

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

Provn of wooden Triangular bracket of size 75x75x40mm at joint of leg and rail of table made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

TABLE DINING 08 PERSON( FD-273)

Long rail

Short rail

Stiffener

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

Provn of wooden Triangular bracket of size 75mm x 75mm made out of 40mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

TABLE DRESSING LADIES (FD-251/378/395)

5mm thick Mirror of size 365mmx1220mm, Make- Saint Gobin/Gold plus with Back plywood of 6mm thick commercial plywood

Sliding glass shutter of 3mm thick as per existing size.

Drawer made out 18/19mm thick prelaminated MDF board at sides and 6mm thick commercial plywood at bottom

Knob as per sample approved

SIDE BOARD (FD-241)

Top made of 18/19mm prelaminated MDF board with wooden beading to edges of the top

Bottom made of 18/19mm prelaminated MDF board with wooden beading to edges of the top

Side made of 18/19mm prelaminated MDF board with wooden beading to edges of the top

Drawer made out 18/19mm thick prelaminated MDF board at sides and 6mm thick commercial plywood at bottom

Shutter made of 18mm thick prelaminated MDF Board with hinges

Back made of 6mm thick commercial plywood.

Bottom frame with 4 Nos of legs shall be made of Ist class hard wood

Knob as per sample approved

TABLE BED SIDE (FD-276)

Top made of 18/19mm prelaminated MDF board with wooden beading to edges of the top

Side made of 18/19mm thick both side prelaminated MDF board with wooden beading to edges

Shelf made of 18/19mm thick both side prelaminated MDF board with wooden beading to edges

Bottom made of 18/19mm thick both side prelaminated MDF board with wooden beading to edges

Back shall be made of 6mm thick plywood commercial

Leg frame with 4 Nos leg and stiffener as per drawing of made Ist class hard wood (teak) duly french polished.

TABLE CENTRE (FD-274/375)

Long rail

Short rail

Side stiffener

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

Provn of wooden Triangular bracket of size 75mm x 75mm made out of 40mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

TABLE 900mm x 900mm (FD-291)

Long rail

Short rail

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

Provn of wooden Triangular bracket of size 75mm x 75mm to made out of 35mm thick hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

Hat Stand with Mirror (FD-FD-233)

5mm thick Mirror of size 300mmx440mm . Make- Saint Gobin/ Gold Plus

4mm thick commercial plywood for back

Chromium plated MS pegs with screw as per sample approved

Sofa Set 3/4/5 Seats FD 281/373/1113 /FD/MAP-II/02 Supply wood and fixing of the fwg new parts after removing broken/unserviceable parts of well seasoned teak wood including tighting other parts of well seasoned teak wood with screw/bamboo pins only of the sofa complete all as specified in drawing & directed by Engineer-in-charge.

Front legs for three/single seater sofa

Rear legs for three/single seater sofa

Long front & Back rail for three seater sofa

Long front & Back rail for single seater sofa

Stiffner for three/single seater sofa

Side short rail for three/single seater sofa

Arms rest for three /single seater sofa.

plywood 10mm for three seater sofa.

plywood 10mm for single seater sofa.

Removal of unserviceable seat and back tapestry cloth and unsv cushion of sofa set three seater and supplywood and fixing with new cushion 550mm x530mm x100mm thick of 32 Density duly covered with well finished best quality tapestry cloth (250 GSM) of approved make/shade including providing quality ZIP all as specified and shown on drawing and directed by Engr-in-charge

All as per Item ser no 20.10 above but for sofa set 4 seater

All as per Item ser no 20.10 above but for sofa set 5 seater

Removal of unserviseable seat and back for Sofa set Three seater of tapestry cloth of 250GSM of approved make/shade duly providing quality Zip all asper specified and directed by Engr-in-charge

All as per Item ser no 20.13 above but for sofa set 4 seater

All as per Item ser no 20.13 above but for sofa set 5 seater

Chair Dining for JCO/OR FD/MAP-II/05

Rear Leg

Front Leg

Side rail with arrangement for fixing of PVC Sheet

Front/back rail with arrangement for fixing of PVC Sheet

Bottom stiffener

Back stiffener

PVC Sheet seat of Make : Amko/Cello as approved by Enginner-in-Charge

Provn of wooden Triangular bracket of size 75mm x 75mm x25mm at joint of leg and rail each chair made out of hard wood and shall be fixed with adhesive and screws as directed by Engineer-in-Charge

PVC/Rubber Shoe as per sample approved

Table Bedside (FD/E-6/MAP/15 (R)) & FD/MAP/01

Back plywood of 6mm thick commercial plywood of existing shape & size

Drawers made out of 18 mm thick prelaminated particle board with teak wood edging

Chromium plated Handle 100mm long

Telescopic channel of good quality.

TABLE DRESSING LADIES INCL STOOL(MAP) (FD/MAP-II/07)

5mm thick Mirror of size 365mmx1220mm, Make- Saint Gobin/ Gold Plus with Back plywood of 6mm thick commercial plywood

Sliding glass shutter of 3mm thick as per existing size.

Drawer of 6 mm thick plywood commercial with 18mm pre-laminated MDF board as per existing shape and size with telescopic channel

Foam cushion 75mm, 40 density covered with fabric on seat to be fixed on 12mm thick plywood on stool as per existing shape and size

Wheel at the bottom of stool as per existing shape and size

RE-CANNING OF CHAIRS : Re-canning of wooden chairs, Bin soiled linen as per Godrej pattern with 2 mm wide half round superior quality cane plastic after taking out existing cane. Border of canning shall be woven with 4 mm half round plastic cane of superior quality as shown in drawing and directed by Engineer-in-charge.

Polishing of Wooden Furniture Items : All wooden surfaces of the following wooden furniture items wheather exposed to view or not when placed in position shall be polished with high gloss french polish to be finished as directed by Engineer-in-Charge duly preparation of surface with emery paper and applywooding putty as and where required.

Bed plywood top wooden - FD 246

Chair Dining FD-279

Chair Writing FD 280

Chair dining officer's FD/MAP-II/04

Chair Easy FD-229

Teapoy (FD-278/382)

Peg Table (FD-277/384)

Table Writing (FD-275)

Table 900x600mm with drawer (FD-283)

Table Dining 6 presons (FD-239/273)

Table Dining 8 presons (FD-273)

Side Board (FD-241)

Table Centre FD-274/375)

Table 900 x 900mm FD-291

Book Case (FD-147)

Hat Stand with Mirror FD-233/FD-362)

Sofa Set 4 Seater (FD-281/373/1113)

Sofa Set 5 Seater (FD-281/373/FD/MAP-II/02)

Chair dining for (JCO's/OR's) FD/MAP-II/05

STEEL FURNITURE : Taking down worned out components of the following steel furniture and S&F new component as per shape and size specified on respective drawings and as directed by Engineer-in-charge

ALMIRAH LARGE STEEL WITH SHELVES (FD-351/1031) Shutter (Single Leaf) made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side after preparation surfaces

Shelves made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side after preparation surfaces

Six Levers brass lock Make : Godrej/Harrison/Link with duplicate keys

Three way Locking Device of 10 mm dia MS rod as per trade pattern incl a coat of red oxide primer

Chromium plated Steel Handle 125mm

Chromium plated MS Key plate fixed with screw and nuts

Leg made of 1.6 mm thick MS sheet with Gas welding incl a coat of red oxide primer

Almirah Small/ Medium steel (FD-350 /1032/243)

Shutter (Single Leaf) made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side after preparation surfaces

Shelves made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side after preparation surfaces

Six Levers brass lock Make : Godrej/Harrison/Link with duplicate keys

Three way Locking Device of 10 mm dia MS rod as per trade pattern incl a coat of red oxide primer

Chromium plated Steel Handle 125mm

Chromium plated MS Key plate fixed with screw and nuts

Leg made of 1.0 mm thick MS sheet with Gas welding incl a coat of red oxide primer

Locker Bedside Steel ( FD-1029)

Shutter (Single Leaf) made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side after preparation surfaces

Shelves made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side after preparation surfaces

Chromium plated 125mm Steel Handle 'D' type for Locker Bedside steel

Leg made of 1.0 mm thick MS sheet with Gas welding incl a coat of red oxide primer

75mm Chromium plated hasp & stapple fixed with rivets of locker steel

Hanging Rod of 1.6mm thick chromium plated MS Rod

TABLE DINING OR's ( FD-165(M) )

Top of 18/19 mm thick MDF board of size 1900 mm x 685 mm covered with aluminium sheet 22 guage on top complete all as specified and fixed with frame with machine screws, as directed by Engineer-in-Charge

Rubber shoe to legs

CHAIR CB STEEL WITH ARMS/WITHOUT ARMS ( FD-75(M)

Seat frame of Chair CB Steel with Arms of 1st class hard wood duly polished with high class black polish incl weaving with 2 mm wide half round plastic cane with Godrej pattern & border with 3 mm wide plastic cane superior quality as shown in drawing

All as per item No 31.01 here-in-before but back frame

All as per item No 31.01 here-in-before but Seat frame for Chair CB Steel without Arms

All as per item No 31.03 here-in-before but back frame

Arms rest for Chair CB Steel with Arms of 1st class hard wood duly polished with high class black polish

PVC cap at top of the frame of the chair (02 Nos to each chair)

PVC Shoe at bottom of the frame of the Chairs (04 Nos to each chair)

TABLE OFFICE CLERK (FD-1004)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

Drawer made of 22 gauge MS sheet with a coat of red oxide primer

Six levers Lock of Godrej/Harrison with duplicate keys.

PVC Shoe at bottom of the leg of the Table

TABLE OFFICE OFFICER STEEL (FD-84(M)/1003)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

Drawer made of 22 gauge MS sheet with a coat of red oxide primer

Six levers Lock of Godrej/Harrison with duplicate keys.

PVC Shoe at bottom of the leg of the Table

TABLE 3' x 2' STEEL WITH DRAWER ( FD-283/1008) & OR Steel (FD-1007)

Top made of 18/19mm thick both side prelaminated MDF board having surface colour as approved with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge

Drawer made of 22 gauge MS sheet with a coat of red oxide primer

PVC Shoe at bottom of the leg of the Table

Charpoy GI Pipe with plywood top: (FD-220)

3 way Galvanized Iron Elbow 32 mm dia. Note weight of each elbow shall not be less than 450 grams

Galvanized iron check nut 32 mm dia. Note :- weight of each check nut shall not be less than 125 grams

Long rail of 32 mm dia galvanized iron pipe medium grade incl threading at both ends as directed

Short rail converted out of retrieved Long rail, Item No 35.03 above incl cutting, threading as required and directed

Leg converted out of retrieved Short rail, Item No 35.04 above incl cutting, threading as required and and directed

Provn of Two Nos MS cleat as shown on drg to hold the MNF set and one MS plate at the bottom to each Leg converted out of retrieved Short rail

12mm thick plywood top BWR Grade ISI Marked of size 1950mm x 900mm (Single piece).

FOAM WITH OUT BACK (FD-77(M)

Seat Plank size 1525mm x 255mm x 25mm made out of 1st class hard wood (teak wood) including apply wooding two coats of french polish complete and fixed to steel /iron frame with suitable GI nuts (09 Nos)

CHAIR WRITING MAP (FD/E6/MAP/12)

Replacement of exising tapestry of seat frame with new tapestry cloth of seat frame approved by Engr-in-charge with PVC liping all round complete all as specified and directed by Engr -in charge Note- Cost of tapestry cloth not less than Rs 450/- RM.

All as per item No 37.01 above but for back frame

Hand rest one piece made of black integral skin,reinforced with MS insert it.

Replacement of complete seat and back with new moulded foam cushioned 40mm density as shape and size, covered with tapestry cloth as approved along with PVC liping all round, complete all as specified

Rubber stopper at the bottom of leg.

BED HARD STEEL( FD/E6/MAP/08(R))

12mm thick plywood top of size 1950mm x 900mm (Single piece) BWR Grade ISI Mark with MS screws, complete all as specified

18mm thick prelaminated particle board at head side of the bed as specified

18mm thick prelaminated particle board at foot side of the bed as specified

PVC shoes at the bottom of leg.

CHAIR COMPUTER (FD/E6/MAP/01)

Replacement of complete seat with new moulded foam cushioned 40mm density as shape and size covered with tapestry cloth cost of tapestry cloth not less than Rs 450/- RM. of cost as approved along with PVC liping all round, complete all as specified

All as per item No 39.01 here-in-before but for back frame

Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

Pedestal assembly complete

Twin wheel coasters press fitted at the bottom of leg.

TABLE COMPUTER (FD/E6/MAP/03)

Top of 18mm thick pre-laminated MDF board incl PVC lipping all around the top

Drawer of 18 mm thick pre-laminated MDF board fixed with telescopic channel

Shelf for keyboard of 18 mm thick pre-laminated MDF board fixed with telescopic channel .

PVC shoes at the bottom of leg.

Chair Verandah (FD-256, 359)

Taking out old U/S cane and rubber shoes from chair verandah, removing of foreign materials from the iron frame by rubbing with sand paper, painting two coats with white synthetic enamel paint and recanning seat and back with 4 mm wide half round white plastic cane of superior quality as directed by Engineer-in-Charge

Provn of Gas welding to the broken joints/parts upto 4-6 joints including provision of MS conduit pipe 19mm dia (upto the length of approx 2 feet long) where required to complete the parts of frame of chair verandah including its smoothening for repainting/recanning all as per drg and as directed.

PVC/Rubber shoes as per sample approved

Chair Visitor of all models (TP) Repair to chair visitor with cushion of all models, including repair/replacement of seat, and back, welding of broken joints of frame of chair visitor to make the chair serviceable all as directed.

Chair Revolving Steel high back (TP)

Replacement of complete seat with new moulded foam cushioned 40mm density as shape and size and fixed over 12mm thick hot pressed plywood, covered with synthetic leatherate as approved and as directed by Engineer-in-charge

All as per item No 43.01here-in-before but for back frame

Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified

Pedestal assembly complete

Twin wheel coasters press fitted at the bottom of leg.

Hydraulic system

CHAIR VERANDAH (FD/MAP-II/06) Taking down unserviceable PVC seat from chair verandah and re-fixing with best quality new PVC Seat 4 mm thick and PVC edges 20mm folded towards back and weight not less than 1.85 Kg and grooves 90x10mm 10 Nos, on seat &back including applywooding one coat of white synthetic enamel paint of superior quality to chairs as per drawings all as specified and as directed by Engineer-in-Charge.

All as per item No 44.00 here-in-before but for PVC Back

Continuous welding 20mm dia MS tube at hand rest frame joint, seat frame joint, back frame joint and seat to back frame stiffener joint Including S& F 50mm X 50 mm x4mm thick MS flat to be fixed in seat frame of chair verandah all as per drawing duly painting the affected portion with two coats of synthetic enamel paint (White) over a coat of red oxide primer all as specified and as directed by Engineer-in-Charge

Painting of the following furniture items with two coat of synthetic enamel paint (colour as approved by Engineer-in-Charge) after preparation of surfaces :-

Almirah Steel Large with Shelves, FD-351/1031

Almirah Small/medium steel (FD-350 /1032/243)

Locker Bedside Steel ( FD-257/1029)

Table Dining OR (FD-165(M)

Chair CB steel with arms/ without arms ( FD-75(M) )

Table office ckerk steel (FD-1007)

Table Steel3'x3' (FD-223/1007)

Table (900x600x760)mm steel with drawer (FD-1007/1008

Table 3'x3' steel (FD-291/1009)

Table officer officer steel (FD-84(M)/FD-1003)

Book Shelf open steel large (FD-69(M)

Book Shelf open steel Small (FD-69(M)

Charpoy IP with plywood top (FD/MAP-II/01)

Rack side steel with tray, FD-97/1023

Chair writing MAP(FD/E6/MAP/12

Bed Hard Steel MAP FD/E6/MAP/08®

Table computer FD/E6/MAP/03

Chair With Hand Rest

TULSI RAINA AND SONS

PACHNANDA BUILDERS

KALSOTRA CONSTRUCTION CO