Construction of 6 Nos Toilet and Leach pit with water Supply arrangement surrounding watch tower at B.M.C. Jail Hotwar Ranchi, Under D.W. and S. Division, Ranchi East, Ranchi.Construction of 6 Nos Toilet and Leach pit with water Supply arrangement su

Carriage of materials from different sources to work site including loading, transporting, unloading and stacking the materials at work site etc. all complete job. as per direction of E/I. (a) Cement +Steel(Lead up to 10 Km)

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials ,labour ,royalty and taxes all complete as per building specification and direction of E/I

Providing designation 75Aone brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I

Centering and shuttering including strutting, propping etc and removal of form for Foundation footings bases of columns etc for mass concrete

Providing PCC M-200 in nominal mix of (1:1.5:3) in foundation with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M.2.5to 3 including screening shuttering mixing cement concrete in mixer and placing in position vibrating striking curing and royalty all complete as per building specification and direction of E/I.

Meter

Providing R.C.C. M-200 with nominal mix of (1:1.5:3)in foundation and plinth with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including curing, carriage the slab manually to site and laying in position all complete (but excluding the cost of reinforcement taxes and royalty all complete) as per building specification and direction of E/I. (SOR-5.3.2.1) 24nos Colx0.90mx0.90mx0.75m = 14.58m3 24nos Colx0.25mx0.25mx0.60m = 0.90m3

Providing R.C.C. M-200 with nominal mix of (1:1.5:3)in lintel with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including curing, carriage the slab manually to site and laying in position all complete (but excluding the cost of reinforcement taxes and royalty all complete) as per building specification and direction of E/I. (SOR-5.3.10) Lintel

Providing R.C.C. M-200 with nominal mix of (1:1.5:3)in columns with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including curing, carriage the slab manually to site and laying in position all complete (but excluding the cost of reinforcement taxes and royalty all complete) as per building specification and direction of E/I.

Providing designation 100A brick work with fly ash lime bricks in C.M.(1:6) in foundation with approved quality of clean coarse sand of F.M.2to2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing ,taxes and royalty all complete as per building specification . and direction of E/I.

Providing designation 100A brick work with fly ash lime bricks in C.M.(1:6) in super structure with approved quality of clean coarse sand of F.M.2to2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing ,taxes and royalty all complete as per building specification . and direction of E/I.

Providing and fixing precoated galvanised iron profile sheets size shape and pitch of corrugation as per spification of direction of E/I.(DSR-12.50) Roof- 6x3.50mx2.30m =48.30m2

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a coat of steel (DSR-10.16) As per item no-9 =48.30m2 @10.76kg/m2 =519.71kg

Providing R.C.C. M-200 with nominal mix of (1:1.5:3)in beam of all types with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including curing, carriage the slab manually to site and laying in position all complete (but excluding the cost of reinforcement taxes and royalty all c

Providing 12mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening curing with all leads and lifts of water scaffolding taxes and royalty all complete as per specification and direction of E/I. .

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M S tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top & bottom rails M S frame shall have a coat of steel primers of approved make and manufacture m s frame covered with 5mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on both side forming styles and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom top and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides of the lock rail top bottom and lock rails shall be provided both side of the panel 10mm (5mm x 2) thick 20 mm wide cross PVC sheet provided as gap insert for top rail & bottom rail paneling of 5mm thick both side PVC sheet to be fitted in the M S frame welded / - sealed to the styles & rails with 7mm(5mm+2mm)thick x 15mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive an additional 5mm thick PVC strip of 20mm width is to be stuck on the intsrior side of the ‘C’ channel using PVC solvent adhesive etc. as per direction of Engineer-in-charge manufacture’s specification & drawing.30mm thick plain PVC door shutters. (DSR-9.118.3) 6Nos. x 0.80m x 2.10m = 10.08m2

Providing and fixing factory made PVC door frame of size 50x47mm with a wall thickness of 5mm ,made out of extructexed 5mm rigid PVC foam sheet ,mitered at corners and jointed with 2nos of 150mm long brackets of 15mmx15mm M.S. square tube ,the vertical door frame profiles to be reinforced with 19mmx19mm M.S. squre tube of 19gauge ,EPDM rubber gasket weather seal to be provided through out the frame .The door frame to be fixed to the wall using M.S. screws of 65/100mm size ,complete as per manufacture’s specification and direction of E/I.

Supplying, fitting and fixing M.S. Grill gate made of 20 x 6 mm M.S. flat fitted on 25mm x 25mm x 6mm M.S. angle frame as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, of required size, taxes, carriage of grill to work site, as per the building specification and direction of E/I 6Nosx0.30mx0.60m =1.08m2 @35kg/m2 =37.80kg

Providing two coats of synthetic enamel paint over steel surface including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification & direction of E/I. Qty=2.25x1.08m2 =2.43m2

Providing and laying 6mm precast commercial grade digial tiles of approved colour in wall with over 12mm cement mortar (1:3) jointed with grey cement slurry flush pointed with white cement including rubbing polishing and cost of curing taxes and royalty all complete as per building specification and direction of E/I. (a)Wall tiles (Fancy tiles 12”x18”)

(b)Floor Tiles (12”x12”) (Anti Skid) 6 Nosx2.40mx1.80m = 25.92m2

Supplying fitting & fixing vitrous white glazed earthen ware I.W.C. of Parry or Hindustan or any other ISS approved make with 100mm dia HCI "P" trap 12.5 Litres capacity P.V.C. low flush bend 15mm dia P.V.C. connection pipe 450mm long with coupling etc. all complete job as per specification and direction of E/I. (With 15mm brass spindle stop cock wt. not less than 450 Gms.) (a)400mm high E.W.C. with 10.00 Liters PVC low down cistern

Supplying fittings and fixing vitreous white glazed earthen ware squting type urinal of Hindustan “parry” or any other approved I.S.S make with 5 liters capacity C.I automatic fulsing cistern of reliance for any other I.S.S approved make with all fittings with C.I or R.S. brackets standard size G.I flush pipe with fittings clamps 15mm C.I body brass spindle stop cock approved quality weight not less than 400grms. 15mm P.V.C / Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a primeing coat of red oxide cutting wall and floor making good the same etc. all complete as per specification and direction of E/I. Squating type urinal (600mmx350mm).

Supplying, fitting and fixing vitreous white glazed earthen ware wash hand basin 550 X 400mm size of Parry or Hindustan or any other I.S.S. approved supported on painted C.I. or R.S. Bracket; 32mm CP brass waste, 32mmdia PVC waste pipe 750mm long with coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Providing and applying 2mm thick J.K. Putty punning on thewall&ceiling including a coat of cement primer all complete as per direction of E/I. (DSR-13.26 Page No-919)

iding two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper ,applying putty wherever required , scaffolding, washing of floors and taxes all complete as per building specification and direction of E/I. As per item no-24

Earth work in excavation (as per I.S. 3114/1965) for laying different type and size of pipe so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of E/I. 32mm dia UPVC pipe in Trench 1590.00mx0.60x1.00m =954.00m3

Supplying all materials labours tools and equipment’s for laying-U-PVC pipe in wall of supreme life /Waterflow pipes with solvent cement on wall floor including supplying and fitting of wall hooks or pipe dam cutting pipe to size where necessary etc. all complete as per specification and direction of the E/I. (U-P.V.C. pipes) 20mm dia U-PVC pipe –(In Wall)

32mm dia U-PVC pipe –(In wall)

32mm dia U-PVC pipe –(in Trench)

Earth work in back filling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification and direction of E/I. For classification of soil item A&B

Supplying all materials, tools and equipment for fitting and fixing special type chrome plated and U-P.V.C. fittings of approved make all complete as per direction of the E/I. Elbow 20mm U-PVC

32mm U-PVC

Supplying all materials, tools and equipment for fitting and fixing special type chrome plated and U-P.V.C. fittings of approved make all complete as per direction of the E/I. Elbow 20mm U-PVC

Tee 20mm U-PVC

Tee (Metal) 20mm x15mmU-PVC

32mm x15mmU-PVC

FTA(Metal) 20mm U-PVC

MTA(Metal) 20mm U-PVC

Supplying all materials, tools and equipment for fitting and fixing special type chrome plated and U-P.V.C. fittings of approved make all complete as per direction of the E/I. Elbow 20mm U-PVC

Socket Plain 20mm U-PVC

Bush 32mmx20mm

Union 32mm U-PVC

Plug 15mmdia G.I

Tank Connector 32mm U-PVC

Brass Elbow 20mmxa15mm

Supplying and fixing UPVC life long valve of approved quality all complete as per specification and direction of E/I. 32mm dia

Supplying all materials, tools and equipment for fitting & fixing C.P. bath room fitting including all accessories etc. all complete as per direction of E/I. (JAL make and any other equivalent approved make) 15mm dia A/S/Cock long thread

15mm dia C.P./Bib Cock long thread eggo head

15mm dia C.P. extension short pieces with thread and couple

15mm dia and thread with C.P. wall flange

100mm dia steel C.P. Jali –

Swan Neck Tap with left hand operating Knob

Soap Dish

Towel Ring –

Providing & fixing 15mm dia 450mm long PVC connection pipe with heavy quality brass coupling at both ends etc. all complete as per specification and direction of E/I.

Supplying fitting and fixing the following item complete with all materials as per specification and direction of E/I. a) Mirror of 6mm thick plate glass beveled edge mirror including C.P. brass hinges 3mm ply wood board fixed with mirror. (600 X 450mm size fancy type)

b) C.P. brass Towel rail with bracket (20mm dia X 600mm long)

Supplying all materials, labours, tools and making bricks masonry platform 0.30M ht. and dia of PVC tank 25mm thick PCC (1:2:4) cement plaster with building etc. all complete including necessary lifting of materials as per direction of E/I. 2000 Ltrs. PVC W/S/tank Platform –

Providing all materials, labours, tools and equipment’s for fixing polythene water storage tank double layer Himgiori/Rotostore ISI marked of equivalent make confirming to IS -12701-1996 fixing on the platform including cutting 4 Nos. hole in tank for rising overflow delivery and wash out including supplying full thread nipple with jam nut and fixing connection etc and supplying fitting and fixing brass ball cock of required size as per specification and direction of E/I. 2000 Ltr HDPE water storage tank

Wring for light point/exhaust fan point/call bell point with 1.5sqmm FR PVC insulated copper conductor single core in surface /recessed PVC conduit, piano type switch, phenolic laminated sheet with suitable size PVC/MS box etc as required.(SOR Energy Department-1.1-1.1.1-Group A) Light point-10Nos

Circuit/submain wiring in PVC conduit:- Wiring for circuit/submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor single core cable in surface /recessed PVC conduit as required (Electrical SOR-1.7-1.7.2) 2x1.5sqmm+1x1.5sqmmearth wire

Provision of 2.00m diax3.00m deep Size Leage pit.(Sub.Estimate )

Supplying, fitting and fixing of P.V.C. pipe of approved make including supplying nails, clips and PVC washer, cement and yarn for making plumber joints properly cutting pipes to sizes including earth work or scaffolding etc. where if necessary etc. all complete as per direction of E/I. PVC Pipe (a)110mm dia PVC pipe ISI marked

(b)75mm dia PVC pipe ISI marked

PVC fittings :- (a)110mm dia PVC B/W/Door

(b)110mm dia PVC plain bend

©110mm dia Door Tee

(d) 110mm dia N. Trap

(e)110mm dia PVC Cowel

(f)75mm dia PVC plain bend

(g)75mm dia Door Tee

(d)Bricks(Lead up to 2+6=8.00Km)

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750mm deep 600x450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster 14) with punning on inside and cement plaster (1:6) with RCC slab cover along with earthwork and 80mm thick PCC (1;3:6) in foundation and refilling all complete as per specification and direction of E/I.

(b)Coarse Sand(Lead up to 1+19=20.00Km)

(c)Stone Chips(Lead up to 1+19=20.00Km)

ADD GST 18% (9 % CGST & 9 % SGST)

Add Labour Cess 1 %