WELCOME MAINT AND CERTAIN REPAIR OF OFFICERS MD ACCN AT SAPPER ENCLAVE GOLF VIEW AND FOD UNDER AGE BR I GE SOUTH UDHAMPUR

Amount

Demolition of cement concrete (unreinforced) in ground floors and in pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar beddig not backing and removing rubbish off the premises complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar as in kitchen platform, floors, aprons etc complete all as specified and as directed.

Providing 50 mm thick cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed.

Providing cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in height, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 (12.5 mm graded aggregate) complete all as specified and as directed.

Use & waste of form work to soffit of suspended slabs such as roof slab floor slab landing and similar work n.exc 200mm thick surface horizantal or sloping rough finished flat surface of concrete complete all as specified and as directed.

Reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in precast cement concrete louvers & jallies 50 mm thick including all moulding but excluding frame set & jointed in cement mortar 1:4 complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed.

Random rubble masonry built in cement mortar 1:6, uncoursed, well bonded, bedded and solidly hearted complete all as specified and as directed.

All as per Srl item No 16 above but except stones complete all as specified and as directed.

Rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete all as specified and as directed. Note : Liquid WPC will be measured and paid separately.

10mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces including finishing even and smooth without using extra cement complete all as specified and as directed.

Rendering 5 mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

Supply only water proofing compound (liquid),ISI marked complete all as specified and as directed.

Joint free non skid ceramic colour tiles 10 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Glazed ceramic coloured tiles 600 x 300 x 10mm thick, digital pattern with dark, light and highlighter combination as in vertical portion such as skirting / dados set and jointed in neat cement slurry and pinted in white or coloured cement to match over 10 mm back coat in CM 1:3 complete all as specified and as directed.

Vitrified Ceramic double charged coloured tiles light shade 10 mm thick double charged (square/rectengular) polished, area of each tile exc 0.36 sqm but n exc 0.42 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Vitrified Ceramic double charged coloured tiles light shade 10 mm thick double charged (square/rectengular) polished, area of each tile n. exc 0.36 sqm as skirting/dado, lining, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over 10mm thick screed bed in CM 1:3 complete all as specified and as directed.

Granite slab 20 mm thick as in steps, jambs, pillars, window cill, cooking platform and the like in cement motar 1:4 including pointing in white cement 1:2 using marble dust with a mixture of pigment to match the shade of granite including cutting polishing and moulding on edges complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps , cooking platform, and other similar situations complete all as specified and as directed.

Providing 75mm thick cement concrete 1:2:4 type B-2 using 40mm graded crushed stone aggregates as in sub-base complete all as specified and as directed.

Providing 25 mm thick cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregates as in sub-base complete all as specified and as directed.

Durastone heavy duty vitrified tiles 10 mm thick Sq/rectangular tiles area of each tile not exceeding 0.36 Sqm as in floors set and jointed in neat cement slurry and pointed in clooured cement to match the surface over 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Pre glazed coloured chequered glossy finished cement concrete tiles 300mm x 300 mm x 20 mm thick, machine pressed; set, jointed and pointed in neat cement slurry, with grey cement and pigment in floors over 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Dismantling asbestos cement (corrugated, semi corrugated) etc sheets in roof covering including ridges complete all as specified and as directed.

Dismantling wall and ceiling boards, fibre pulp insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided all as specified and as directed.

Rolled mild steel section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors ; fixed with angle cleats or other connecting plates conforming to grade Fe 410-W (Gde-E-250) quality-A complete all as specified and as directed.

Pre painted galvalume aluminium zinc coating GI based corrugated sheets 0.5 mm thick of any colour having tensile strenght of 550/MPA as in roof covering, cladding to wall fixed with self taping screws complete all as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Providing and fixing flase ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2% humidity resistance of 99%, NRCO 0.50 to 0.75 as per IS 8225 : 1987, non combustible as per BS 475 (Part 4)-1970 and light reflectance of 85%(minimum) to be laid in true horizontal level suspended on interlocking metal T Grid of hot dipped galvanized iron section of 0.33mm thick (galvanised @ 120 grams per sqm both sides) comprising of main T runners of size 15 x 32 mm of length 3000 mm, cross T of size 15 x 32mm of length 600 mm x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e 50 mm long, 8 mm outer diameter M-6 dast fasteners, 6mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x 0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450mm centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specificatins, drawing and as per directions of Engr-in-Charge or Garrison Engineer.

5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame all as specified and as directed.

S & F in repairs solid PVC wall lining consisting of 5mm thick Plain Colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame all complete all as specified and as directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frames) n.exc 1.5 Sqm each including cutting holes for taking out hold fasts, dismantaling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified and as directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n.exc 4 Sqm each including cutting holes for taking out hold fasts, dismantaling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified and as directed.

Taking down shutters of any description exceeding 1 square metre not exceeding 2 square metre each complete all as specified and as directed.

Taking down and refixing of shutters of any description exceeding 1 square metre not exceeding 2 square metre each complete all as specified and as directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube and fixed in opening as per specification and drawing complete all as specified and as directed.

Factory made solid panel PVC Moulded door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. Clause No. 8.B.1 to 8.B.10 and drawing on page No. 156 & 157 of MES SSR-2010 Part-II complete all as specified and as directed.

Pressed steel frames for doors made out of 1.25mm thick MS sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate ,12mm bar thresh hold etc. complete , of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and as directed.

All as per item No 48 above but frame size 105 x 60 mm complete all as specified and directed

35 mm thick factory made, 2nd class hard wood , plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

Factory made 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

30mm thick flush shutters, solid core construction, with block board core and plywood face panels, with decorative face veneer on both faces with lipping/ frame to match complete all as specified and as directed.

Mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Mild steel cold rolled butt hinges medium weight 100 mm long complete all as specified and as directed.

Aluminium anodised barrel tower bolts of extruded section with 200 mm long bolt complete all as specified and as directed.

Aluminium alloy, sliding door bolt 300 mm long with hasp, staple ( bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

Aluminum handles cast type, anodised, 150 mm size complete all as specified and as directed.

Mild steel, 300 mm, ordinary rat tail rod pattern door spring including roller and roller plate, fixed to frame complete all as specified and as directed.

S & F in repairs aluminium anodised barrel tower bolts of extruded section with 200 mm long bolt complete all as specified and as directed.

S & F in repairs aluminium alloy, sliding door bolt 300 mm long with hasp, staple ( bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S & F in repairs aluminum handles cast type, anodised, 150 mm size complete all as specified and as directed.

Mild steel, 300 mm, ordinary rat tail rod pattern door spring including roller and roller plate, fixed to frame complete all as specified and as directed.

Powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates (minimum thickness of powder coating 50 micron) including joining cleat for fixing etc complete all as specified and as directed.

Powder coated anodised sliding/hung type aluminium door, window and ventilator shutters (minimum thickness of powder coating 50 micron), without sash, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 No), hinges type B-21 100 mm long (2Nos) suitable handle (1 No), aluminium tower bolt 100 mm (1No) etc complete all as specified and as directed.

Powder coated Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and as directed.

S & F in repairs Door closer aluminium (extruded section body) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

Hacking out old broken glass panes (any thickness, size quality or description) from wooden frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed.

4mm thick Figured glass pin headed type and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

Decorative solar control film 25 micron reflective type sticked to glass panes as per instruction of manufacturer including removal of existing complete all as specified and as directed.

S&F in repairs Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F in repairs drapery rod of 25mm dia stainless steel decorative along with brackets and end caps of quality as approved by GE.

S & F in repairs 18/19 mm thick prelaminated particle board, exterior grade , prelaminated one side with decorative choice lamination and other side balancing white lamination , fixed with screws to timber frame work as in kitchen cabinets and cupboard shutters complete all as specified and as directed.

S & F in repairs18/19mm thick block boards grade 1 quality exterior grade commercial type fixed with screws to timber frame work including decorative laminate type 1 of surface finish colour and pattern as approved with adhesive 0.90 mm thick complete all as specified and as directed.

Continuous (piano) hinges, mild steel,bright finishor electrogalvanised width of flaps (when open) 30 mm complete all as specified and as directed.

Hetich softcloser hinges of stainless steel premium quality complete all as specified and as directed..

100mm hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

Magnetic catches brass body and striking plate including letting in and fixed suitable for cupboard shutters complete all as specified and as directed.

75 mm decorative Brass handles, cast type, polished bright complete all as specified and as directed.

S & F in repairs stainless steel cutlery organiser set of size 0.45 x 0.60 fixed in drawer of kitchen cabinets including stainless steel telescopic channels complete all as specified and as directed.

S & F in repairs stainless steel two shelves bottle pull outs set of size 0.60 x 0.60 fixed in drawers of kitchen cabinets including stainless steel telescopic channels complete all as specified and as directed.

S & F in repairs stainless steel plate basket set of size 0.45 x 0.60 fixed in drawers of kitchen cabinets including stainless steel telescopic channels complete all as specified and as directed.

S & F in repairs stainless steel three shelves oil pull out basket of size 0.45 x 0.60 fixed in drawers of kitchen cabinets including stainless steel telescopic channels complete all as specified and as directed.

S & F in repairs telescopic channels 60cm long and 25mm wide with necessary screws complete all as specified and as directed.

Supply and fix in repairs PVC valveless, syphonic action, flushing cistern low level 10 ltrs capacity, white with inlet ball valve float and handle including brackets and flush pipe of polyethylene of low or high quailty PVC 32mm dia complete all as specified and as directed by Engr-in-charge or Garrison Engineer.

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and as directed.

S & F in repairs CP Towel ring square with round flange complete all as specified and as directed.

S & F in repairs CP Toilet paper holder with flap complete all as specified and as directed.

Supply and fix in repairs Brass wall mixer, Chromium plated 3 in 1 system with provision of both telephone shower and overhead shower complete with 115 mm long bend pipe and wall flange all as per Cat No.8275 of Cat. No.CON-281KN or T1723Cor G1417A1 of equivalent of complete all as specified and as directed.

S & F in repairs shower diverter single lever exposed part kit of hi flow diverter consisting of operating lever wall flage screwed for iron pipe of 15mm complete all as specified and as directed.

Supply and fix in repairs sink mixer with regular swinging spout (wall mounted model) with connecting legs and wall flanes, 15 mm bore, brass, chromium plated, fancy type with crutch or butterfly handle conforming to IS screwed down, screwed for iron pipes or for brass ferrule complete all as specified and as directed. Make : Cat No ARI-39309.

Supply and fixing "as in repair" stop valves/angle valve of 15 mm bore, but fancy type, chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions including necessary fitting as required at site complete all as specified and directed by Engr-in-Charge or Garrison Engineer. Make : Cat No LYR-38053

Supply and fix in repairs Bib tap 15 mm bore, brass, chromium plated, fancy type with crutch or butterfly handle conforming to IS screwed down, screwed for iron pipes or for brass ferrule complete all as specified and as directed. Make : Cat No ARI-39037

Supply and fix in repairs two way Bib tap 15 mm bore, brass, chromium plated, fancy type with crutch or butterfly handle conforming to IS screwed down, screwed for iron pipes or for brass ferrule complete all as specified and as directed. Make : Cat No ARI-39041

S&F as in repairs fancy type single lever basin mixer Pillar tap, cast copper alloy, with capstan heads, chromiuk plated, screwed down high pressure with or without lettered "HOT" or "COLD" with long screwed shanks and fly nuts, screwed for iron pipe of bore 15mm complete all as specified and directed Make : Cat No ARI-39001B

Supply and fix in repairs long body Bib tap 15 mm bore, brass, chromium plated, fancy type with crutch or butterfly handle conforming to IS screwed down, screwed for iron pipes or for brass ferrule complete all as specified and as directed. Make : Cat No CON-107KN.

Supply and fix in repairs hand shower fixed complete all as specified and as directed. Make : Jaquar cat No HSH-1737.

S & F in repairs Over head Shower rose 200X200mm Square shape single flow CP With gray face plate with rubit cleaning system screwed for iron pipe of 15mm complete all as specified and as directed.

S&F in repairs Brass chromium plated shower rose 125mm size including shower arm all as specified and as directed.

S & F in repairs health faucet with 8mm dia 1.00m long flexible tube and wall hook with all accessories all as aproved complete all as specified and as directed.

S & F in repairs CP Towel rack 600mm long with lower hanger complete all as specified and as directed.

S&F in repairs vitreous China wash down water closet pan (pedestal pattern) couple closet VGS-WHT-0922BS size-810x405x730 trap distance S-250,including cistern VGS-WHT-1307, Soft close seat cover ZPS-WHT-1024UF with nuts and bolts as fixed and repair complete all as specified and as directed.

Supply and fix in repairs plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and as directed by Engr-in-charge or Garrison Engineer.

S&F in repairs Corner glass self with brackets complete all as specified and as directed.

S & F in repairs soap dish fancy type chromium plated fixed with brass screws and wooden/plastic cleats complete all as specified and as directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing to storeyard complete of bore 15mm complete all as specified and as directed..

All as per item No 109 but 20mm bore pipe complete all as specified and as directed.

Steel water tubing of nominal bore 15 mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and as directed.

All as per item No 111 above but 20mm dia complete all as specified and as directed.

S&F in repairs PVC (SWR) pipe single socketed in any length with rubber rings joints fixed to walls for 110 mm bore pipe complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

Supply and fix in repairs vitreous china wash hand basin white flat back size 550x400mm excluding taps waste chain and plug and porcelain stopper but including brackets waste fitting brass chromium plated 32mm dia with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed etc complete all as specified and as directed by Engr-in-charge or Garrison Engineer.

Sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Supply and fix in repairs Matt finish stainless steel sink, double bowl , made out of 1mm thick sheet for kitchen or laboratory with plug, washers, waste pipe, cast iron cantilever brackets connecting union overall size 810 x 510 x 203 mm with bowl size 405x354x203mm fixed complete all as specified and as directed by Engr-in-charge. Make : Cat No 1232DM.

S&F repair vitreous China wash down water closet pan ( pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with P or S trap but including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device including connection to drain and flush pipe complete all as specified and as directed.

S&F in repair water closet white vitreous china ware Orissa pattern of size 580x440mm with integral foot rest ‘P’ or ‘S’ trap 100mm dia front or back inlet incl provision of PCC bedding type B1, 1:2:4 ( 20 mm graded aggregate) and connection pipes ( excluding flushing cistern but including flushing pipe 32 mm dia MS chromium plated) (rate also include for taking off unhygienic of WC) complete all as specified and as directed.

Rotational molded (three layered as per IS 12701) polyethylene water storage tank (cylindrical vertical with closed threaded top) hoisted and fixed in position including connecting inlet/outlet pipe connecting with necessary fittings all as required at site and specified in SSR part -I of capacity 1000 litres including all accessories {i.e GI nipples and Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of bore 20mm (Minimum weight 210 gram) etc}, and dismantling of old UNSV water tank of same capacity all as specified and directed.

All as per item No 121 above but 500 ltr capacity water storage tanks complete all as specified and as directed.

Supply and fixing "as in repair" ball valves of size 20mm bore dia high pressure of PTMT (Make-Prayag) with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 210 gms) screwed for iron pipe and fixed including necessary fitting as reqd at site complete all as specified and as directed.

Supply and fixing "as in repair" ball valves of size 15mm bore dia high pressure of PTMT (Make-Prayag) with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 210 gms) screwed for iron pipe and fixed including necessary fitting as reqd at site complete all as specified and as directed.

S & F in repairs 50mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S &F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plate bracket guard and railing 60 cm long complete all as specified and as directed.

Supply and fix Stainless steel Plate rack of size 780mm x 910 x 250mm (31"x36"x10") with separators and 3 tier shelves, provisioning of hook 9 Nos made out of stainless steel sheet of grade AI SI-304 and fixed in repairs complete all as per Cat No P-348 of Prayag or equivalent all as specified and as directed.

Supply and fix in repairs 32mm bore waste fittings, brass, chromium plated for glazed ware sinks, basins, etc, with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by Engr-in-charge or Garrison Engineer.

Supply and fix in repairs flexible PVC waste pipe suitable for wash hand basin and Kitchen Sink all as specified and as directed.

Supply and fix in repairs PVC connection 15mm size PTMT nuts length 450mm complete all as specified and as directed by Engr-in-charge or Garrison Engineer.

Supply and fixing in repairs PVC tank lid for water tanks of any capacity including all locking arrangements, nuts, bolts etc for fixing complete all as specified and directed by Engr-in-Charge or Garrison Engineer.

S&F in repair GI Nipple 20 mm suitable for HDPE water tank complete all as specified and as directed.

Supply and fixing in repair ball valves of size 15mm bore dia high pressure of PTMT (Make-Prayag) with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 142 gms) screwed for iron pipe and fixed including necessary fitting as reqd at site complete all as specified and directed by Engr-in-Charge or Garrison Engineer.

Supply and fixing in repair ball valves of size 20mm bore dia high pressure of PTMT (Make-Prayag) with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 210 gms) screwed for iron pipe and fixed including necessary fitting as reqd at site complete all as specified and directed by Engr-in-Charge or Garrison Engineer.

Supply and fixing in repair brass ball valves of size 20mm bore dia high pressure of with polyetylene float and flynut screwed for iron pipe and fixed including necessary fitting as reqd at site complete all as specified and directed by Engr-in-Charge or Garrison Engineer.

Supply and fixing in repair stop valves/angle valve cast copper alloy 15 mm, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions including necessary fitting as required at site complete all as specified and directed by Engr-in-Charge or Garrison Engineer.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and as directed.

Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and as directed.

Providing, cement concrete type B0 1:2:4 (12.5 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

Rendering 5 mm thick on fair faces of concrete surface in CM 1:3 finished even and smooth without using extra cement with WPC at the rate of 3% by weight of cement complete all as specified and as directed.

Cleaning the entire roof surface thoroughly to remove all loose particles, dust/dirt particles and applying with One coat of industrial bitumen 85/25 grade at the rate of 1.20 Kg/Sqm over the plastered surfaces of roof all as specified and as directed by the Engineer-in-Charge or Garrison Engineer.

3mm thick APP based polymeric membrane minimum weighing 3 kg/sqm non-woven polyester reinforcement polymeric water proofing membrane (wt not less than 150 gms/sqm) laid on primed surfaces by gas flame torch application and apply one coat of industrial bitumen 85/25 grade at the rate of 1.20 Kg/Sqm over APP Memberence complete all as specified and as directed by the Engineer-in-Charge. Note :- Water proofing treatment will be done by IWL or through a specialized agency which will further have to give a five years warranty for rectification of any defect if incurred at a later stage, otherwise no payment shall be made to the contractor if water proofing treatment is executed by engaging local labour complete all as specified and as directed.

Applying a coat of bituminous aluminium paint @0.10kg/Sqm as weather proof coat all as specified and as directed by the Engineer-in-Charge or Garrison Engineer.

Preparation of new steel and iron surfaces of any discription exceeding 10 cm width or girth, not otherwise described and applying two coat of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and as directed.

Preparation of new wood or wood based surfaces of any discription not otherwise described exceeding 10 cms width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Cleaning and removing all scale and dirt, etc with chlorine or bleeching, from PVC water storage tank of any capacity exc 250 and n.exc 1000 ltrs without dismantling the tank and from mouths of circulating pipes, etc incl writting "Tank Cleaned on ____" indicating the date, month & year of cleaning on external wall of tanks with synthetic enamel paint and stainsils complete all as specified and as directed.

One coat of synthetic enamel painting on old painted steel surfaces of any description, not otherwise described over 10cm width or girth including preparation complete all as specified and as directed.

One coat of synthetic enamel painting on old painted wooden surfaces of any description, not otherwise described over 10cm width or girth including preparation complete all as specified and as directed.

Preparation of new plastered wall surfaces by washing rubbing down and stopping of distempered surfaces and filling the nail holes by white cement and applying two coats of oil bound distemper white or tinted with roller application over a coat of chalk whitening primer over 3mm thick wall care putty complete all as specified and as directed.

Preparation of new plastered surfaces of walls and applying two coats of cement based paint white or tinted complete over a coat of chalk whitening primer complete all as specified and as directed.

Preparation new surfaces plastered or unplastered and applying three coats of white wash on ceiling complete all as specified and as directed.

Preparation of old decorated wall surfaces by washing rubbing down and stopping of distempered surfaces and filling the nail holes by white cement and applying one coat of oil emulsion distemper white or tinted with roller application complete all as specified and as directed.

Preparation of old decorated wall surfaces by washing rubbing down and stopping of distempered surfaces and filling the nail holes by white cement and applying two coats of oil bound distemper white or tinted with roller application over a coat of chalk whitening primer over 3mm thick wall care putty complete all as specified and as directed.

Preparation of old decorated surfaces of walls by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent walls and trading oil and greasy spots and applying for one coat of white wash complete all as specified and as directed.

Preparation of old plastered surfaces of walls and applying two coats of cement based paint white or tinted complete all as specified and as directed.

Complete removal of existing treatment from wall/facia surfaces by rubbing, washing down and stopping of distempered and painted surfaces and applying two coats of apex ultima paint over a coat of primer and thin layer of wall care putty (Birla/JK) including preparation of surfaces (colour of apex ultima approved complete all as specified and as directed.

Preparation of old decorated surfaces of walls by by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent walls and trading oil and greasy spots and applying one coat of cement based paint white or tinted complete all as specified and as directed.

Applying one coat of Royale luxury Emulsion on old decorated plastered surfaces of walls after preparation of surfaces complete all as specified and as directed.

One coat of white wash on ceiling on old plaster surfaces incl prep of surfaces complete all as specified and as directed.

S&F in repairs stainless steel peg set of six as per sample complete all as specified and as directed.

Providing of treating the soil along with external perimeter of building at the rate of 2.25 litre of Antitermite treatment chemical emulsion per metereof the perimeter wall, complete all as specified and as directed by Engr-in-Charge. Note : The treatment work shall be carried through authorized agency only, and certificate for the same ofr warranty shall have to be furnished before submitting payment)

Providing treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5ltr/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed.

RAJ MOHD