Special repairs to married Accn and provision of perimeter wall at Old Cantt Allahabad.

Amount

Demolition of Concrete work (un-reinforced) in ground floors and pavings including floor tiles not exeeding 15 cm thickness (below or above ground level) and removal of debris from the site, complete all as specified and directed.

Demolition of Cement Concrete (reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) including cutting of reinforcement to facilitate demolition, complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc, laid bedded pointed in any mortar, complete all as specified and directed.

Taking down cement plaster on brick or stone walls or wall tiles etc including raking out joints, hacking for key, scrubbing down with water etc, including removal of rubbish off the premises, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store, removing rubbish off the premises, complete all as specified and directed.

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Glazed ceramic coloured tiles as in vertical surface of walls such as skirting / dado and risers to steps, size of tile shall be 450mm x 300mm x 7mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles, laid over and including provison of 10 mm thick rendering as in backing of tiles in cement mortar 1:4, complete all as specified and directed.

Non - skid ceramic, jointless, coloured tiles 7 to 8 mm thick, size of tiles shall be 400mm x 400mm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 15mm thick screed bed in CM 1:6, complete all as specified and directed.

Non - skid ceramic, jointless, coloured tiles 7 to 8 mm thick, size of tiles shall be 400mm x 400mm, as in vertical surfaces of walls such as skirting / dado and risers to steps etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 10mm thick backing coat in CM 1:4, complete all as specified and directed.

Machine cut Kota stone slab 20 to 22 mm thick, as in flooring, laid over and including provision of 20 mm thick screed bed in cement mortar 1:4, laid and jointed with grey cement slurry mixed with colouring pigment to match with the colour of tile, including rubbing and mirror polishing, complete all as specified and as directed.

Kota stone slab 18 to 20mm thick, as in riser of steps, skirting, dado and pillar, laid over and including provision of backing coat of 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with colouring pigment to match with the colour of tile, including rubbing and polishing, complete all as specified and directed.

Chequered cement concrete tiles 20cm x 20cm x 25mm thick, with grey cement and pigment; set, jointed and pointed in neat cement slurry as in floors, laid over and including provision of 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Cement concrete 1:5:10, type E-2 (using 40mm graded stone aggregate) as in foundation, filling, sub bases, sunken floor etc., complete all as specified and directed.

Machine cut baroda Green marble stone slab 18 to 20 mm thick, as in Kitchen cooking platform, laid over and including provision of 15mm thick screed bed in CM 1:4, laid and jointed in grey cement slurrry mixed with pigment to match the shade of the slab, including cutting, rubbing and polishing complete and including nosing of the edges half round, complete all as specified and directed. NOTE:- Stone slab shall be fixed in two piece.

Brick work with fly ash old size bricks, straight or curved on plan exceeding 6 metre mean radius, built in cement mortar 1:6, complete all as specified and directed.

Cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at a length not exceeding 3 metres and at every change of direction and filling the same with and including provision of bitumen and sand 1:3 by weight, complete all as specified and directed.

Rendering 15mm thick, on fair faces of brick work or concrete surfaces in CM 1:4 mixed with water proofing compound, finishing the surface even and smooth without using extra cement, complete all as specified and directed. NOTE:- Water proofing compound shall be measured and paid separately as 'Supply only' under respective item of this Schedule.

Rendering 15mm thick, on fair faces of brick work or concrete surfaces in CM 1:6, finishing the surface even and fair, complete all as specified and directed.

Rendering 5mm thick in CM 1:3 on concrete surfaces in ceiling, finished fair and even, complete all as specified and directed.

Supply only integral water proofing compound, complete all as specified and directed. NOTE:- The water proofing compound shall be incorporated in the work all as per manufacturers instructions only.

Cleaning the sunken floor surfaces, including taking down existing roof treatment of any type from roof slabs and cleaning of surfaces, by wire brushes, brooming, removing dust, including dismantling of floor, lime terracing as required and applying following:- (a) Bitumen primer confirming to IS-3384-1965 @ 0.50 kg per sq.m. (b) Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sq.m confirming to IS – 702-1998 for water proofing membrane. (c) Applying of APP water proofing membrane weight not less than 3 kg / sq.m over entire area with overlaps and sealed all as specified and directed. (d) Again applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg / sq.m over water proofing membrance. (e) Dusting dry sand @ 0.75 kg per sq.m over water proofing membrane.

Taking up or down galvanised steel tubing, 15 mm bore, including connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down galvanised steel tubing, 20 mm bore, including connections, including cleaning for refixing or removal to store, complete all as specified and directed.

GI tubing medium grade, galvanised with all fittings including short lengths, laid in floors or fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 15mm bore of pipe, complete all as specified and directed.

GI tubing medium grade, galvanised with all fittings including short lengths, laid in floors or fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 20mm bore of pipe, complete all as specified and directed.

GI tubing medium grade, galvanised with all fittings including short lengths, laid in floors or fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 15mm bore of pipe, except tubing, complete all as specified and directed. NOTE:- The GI tubing retrieved from Sl. No. 22.00 here-in-before shall be used in this item.

GI tubing medium grade, galvanised with all fittings including short lengths, laid in floors or fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 20mm bore of pipe, except tubing, complete all as specified and directed. NOTE:- The GI tubing retrieved from Sl. No. 23.00 here-in-before shall be used in this item.

Dismantling of PVC water tanks of capacity exceeding 250 litres but not exceeding 500 litres, complete all as specified and directed.

Rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes, complete all as specified and directed.

Gun-metal, globe or gate valves, 20 mm bore, with iron wheel head, screwed both ends for iron pipe, fixed in repair, complete all as specified and directed.

Ball valve high pressure PTMT with epoxy coated aluminium rod and high density plastic ball secured for iron pipe of dia 20mm (minimum weight 210 grams), fixed in repair, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store, complete all as specified and directed. NOTE:- Measurement shall be overall as fixed along the centre line over fittings and accessories.

UPVC (SWR) 110 mm bore pipes single socketed ends, in any length with rubber ring joints, laid in floors or trenches, complete all as specified and directed.

UPVC (SWR) 110 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

UPVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber ring joints, laid in floors or trenches, complete all as specified and directed.

UPVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

UPVC (SWR) bends of any radius and 110mm bore fixed to pipes in walls making good with fixed to PVC pipe joint with rubber gasket solvent, complete all as specified and directed..

UPVC (SWR) bends of any radius and 75 mm bore fixed to pipes in walls making good with fixed to PVC pipe joint with rubber gasket solvent, complete all as specified and directed..

UPVC (SWR) junction single, (Single T) equal or unequal, 75mm bore, with access door, complete all as specified and directed..

UPVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, with access door, complete all as specified and directed..

Stack clamps made out of 50 mm by 5 mm mild steel flat iron, fixed to wall or roof, for any dia of pipe (110mm / 75mm) with and including provision of all fixing arrangements, complete all as specified and directed.

Stainless steel plate rack / utensils rack of size 600mm x 750mm x 250mm depth made out ot 0.63mm thick stainlesss steel sheet, fixed to wall with brass screws including provision of necessary fittings / fixtures viz., nuts, bolts and washers of suitable size, including taking down old and unserviceable plate rack, complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, fixed in repair, complete all as specified and directed.

Soap dish, stainless steel, of size 160mm x 160mm x 90mm, any type, fixed to plugs with chromium plated brass screws, fixed in repair, complete all as specified and directed.

UPVC (SWR) floor trap, 75 mm bore, plain with grating including jointing with solvent cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate), fixed in repair, complete all as specified and as directed.

UPVC (SWR) multi floor trap, 75 mm bore, plain with grating including jointing with solvent cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate), fixed in repair, complete all as specified and as directed.

Kitchen sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35mm x 35mm x 5 mm, 32mm dia brass waste coupling, 32 mm dia PVC waste pipe (rigid quality) and connecting union to pipe overall size 915mm x 460xmm, bowl size 410mm x 330mm x 160mm, fixed in repair, complete all as specified and directed.

Corner Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass with chromium plated bracket guard and railing, fixed in repair, complete all as specified and directed.

Tubular towel rail of brass chromium plated, 20mm dia, D type, 600mm long between flanges, fixed in repair, complete all as specified and directed.

Angle valve, cast copper alloy chromium plated with long shank and cup (angle type), screwed down, high pressure, with crutch or butterfly handle, 15mm bore, screwed for iron pipe or for unions, fixed in repair, complete all as specified and directed. MAKE:- L&K Cat No. 0047 or techno-commercially equivalent model in any one make mentioned here-in-after

Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type, chromium plated with long shank and cup (concealed type), 15 mm bore, fixed in repair, complete all as specified and directed.

Bib taps, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule for 15mm bore, fixed in repair, complete all as specified and directed.

Grating round 125 mm size of PTMT (minimum weight 100 gms), fixed in repair, complete all as specified and directed.

Pillar tap cast copper alloy with capstan head, chromium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe 15 mm bore, fixed in repair, complete all as specified and directed.

Brass chromium plated shower rose 65 to 90 mm size with swivel joints, fixed in repair, complete all as specified and directed.

UPVC (SWR) WC connector bent type, 110mm bore, fixed in repair, complete all as specified and directed.

PVC low level cistern, 10 litre capacity, ‘ white’ with inlet, float valve including bracket with 32mm dia PVC pipe 600 mm long, fixed in repair, complete all as specified and directed.

Supply only PVC connection 600mm long and 15 mm dia with brass fly nut at both ends, complete all as specified and directed.

Vitreous china squatting pan, ‘Orissa’ pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe,CI trap 100 mm Bore of pipe etc, fixed in repair, complete all as specified and directed.

Vitreous China wash hand basin white flat back of size 550 mm X 400mm fixed on cantilever brackets of mild steel, a 32mm dia brass waste coupling and 32 mm dia PVC waste pipe (rigid quality), fixed in repair, completed all as specified and directed.

Low density polyethylene pipes (LDPE), 40 mm bore, of pressure rating 6 kgf/cm2 fixed complete to walls,ceilings or in floors etc for WHB and sink, fixed in repair, complete all as specified and directed.

Taking down chowkhats or frames, with shutters (without taking off shutters from the frames), area not exceeding 1.5sq.m each, complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutters from the frame) area exceeding 1.5 sq.m but not exceeding 4.0 sq.m each and removing from site, complete all as specified and directed.

Taking down shutter of any description exceeding 1 sq.m but not exceeding 2 sq.m each and removing from the site, complete all as specified and directed.

PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in hold fasts, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete as directed including provision of necessary use and waste of form work, complete all as specified and directed.

Mild steel work as in holdfast made out of flat iron conforming to Fe-290 Gde-E-165, including necessary welding or fixing nuts and bolts, complete all as specified and directed.

Rolled mild steel conforming to Fe 410-W (Gde-E- 250) quality-B, sections as in framing for cladding, glazing and the like including door frames/ chowkhats or cooler stands, fixed with angle cleats and connecting plates etc., including necessary cutting, bending and welding as required, complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet & edges will be printed to match with the prelam sheet reinforced with M.S. Square tube, complete all as specified and directed. MAKE:- Syntex / Rajshree Plastic Wood Forex, Indore

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete as shown in SSR Part- II, complete all as specified and directed. MAKE:- Syntex / Rajshree Plastic Wood Forex, Indore

Glazed and skeleton shutters, 35mm thick, second class hardwood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), divided into squares with plain, chamfered or rounded mitered beads for securing glass/gauge complete all as specified in SSR Pt- I, section 8, clause 8.20(a), complete all as specified and directed.

Flush shutters 32 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Block board, 18 to 19 mm thick, grade-2 quality, interior grade, commercial types in cup board shutter / shelf and fixed with screw and teak wood beading all around / exposed surfaces fixed in repair, complete all as specified and directed.

Mild steel conforming to Fe 290.Gde-E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and / or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed.

Factory made steel window with side hung shutter including box type hinges with steel handle, steel peg stay, complete with glazing bar, dovetailed or welded complete all as specified and directed.

Factory made steel window with side hung shutter including box type hinges with steel handle, steel peg stay, complete without glazing bar, dovetailed or welded complete all as specified and directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

Mild Steel handle (left or right) for steel window of existing size including necessary welding / riveting etc. fixed in repair, complete all as specified and directed.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, fixed in repair, complete all as specified and directed.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal/wooden frame complete all as specified and directed.

Sheet glass, 3 mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 sq. m in each pane including hacking out of glass panes, complete all as specified and directed.

Sheet glass frosted on one side, 4 mm thick, ordinary quality and glazing with oil putty or wooden beads in square area not exceeding 0.5 sq.m in each pane, complete all as specified and directed.

Supply only second class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including butt hinge etc & all necessary labours; articles not exceeding 200 cu. cm each, complete all as specified and directed.

Mild steel sliding door bolts, 300 mm long, stove enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, complete all as specified and directed.

Aluminium anodised barrel tower bolts, 200 mm long, of extruded section and fixed, complete all as specified and directed.

Aluminium anodised barrel tower bolts, 150 mm long, of extruded section and fixed, complete all as specified and directed.

Butt hinges 100 mm size, medium weight cold rolled mild steel, complete all as specified and directed.

Butt hinges, 100 mm long, extrucded aluminium alloy with brass/ bronze hinge pin, anodised type B-21, bright polished, complete all as specified and directed.

Aluminium handles 150 mm size cast type, anodised, complete all as specified and directed.

Aluminium anodised hasp and staple, safety type, 150 mm size fixed in repair, complete all as specified and directed.

Mild steel tubing of 25 mm dia with PVC coating for curtain rod fancy type including fancy type PVC brackets (wall to wall or flush to wall) for securing to curtain rod, fixed in repair, complete all as specified and directed.

Taking down shutter from frame, exceeding 1 sq.m but not exceeding 2 sq.m, cutting of bottom rail / shuttter and finish properly, re-fixing in same opening after easing / adjusting of the same, complete all as specified and directed.

Continuous (piano) hinges, mild steel bright finish or electro galvanized, 30 mm width of flaps (when open) complete all as specified and directed.

Reinforced cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in cover slabs (for manholes, kitchen slab etc), shelves and similar articles with plain faces complete all as specified and directed. NOTE:- Reinforcement shall be measured and paid separately under respective item of BoQ.

Mild steel TMT bars of size 6 to 8mm dia, cut to length, bent to shape as required including cranking, hooking ends & binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed.

Form work for rough finished flat surfaces concrete such as sides and soffits of floor or roof beams, beam haunchings girder, lintels, cantilevers, shelves including supports overhangs etc., complete all as specified and directed.

Formwork to rough finished edges of concrete flats, treads, breaks in floors, window cills, concrete railings,openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide, complete all as specified and directed.

Preparation of old plastered surfaces of ceilings and applying two coats of white wash, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed. .

Preparation of newly plastered surfaces of walls and applying two coats of acrylic emulsion paint, complete all as specified and directed.

Complete removal of existing treatment of wall and applying two coats of acrylic emulsion paint over a coat of primer including prepartion of surfaces, complete all as specified and directed.

Preparation of newly plastered surfaces and applying two coats of cement base paint, complete all as specified and directed.

Complete removal of existing treatment on old plastered surfaces of walls and applying two coats of cement base paint including preparation of surfaces, complete all as specified and directed.

Application of 1mm thick wall care putty (in two layer) on new and old plastered surfaces of walls, including filling all depression, spots, nail holes etc., to give smooth finish on internal / external surfaces, complete all as specified and directed.

Preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Preparation of old wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Preparation of new steel and iron surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Preparation of old steel and iron surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Rendering 15 mm thick in cement mortar 1:3 on concrete surfaces (such as chajjas, facia, roof projection and parapet) and finishing the surface fair and even, with and including provision of all necessary scaffolding, complete all as specified and directed.

Demolition of mud / lime concrete from roof not exceeding 200 mm thick, including plastering, leaping, vegetation and removing the debris to a exceeding 250 metre but not exceeding 500 metre, complete all as specified and directed.

Brushing neat cement slurry @ 3 Kg/sq.m after cleaning of concrete surface, complete all as specified and directed.

Cutting out cracks to 'V' section of existing roof or terracing, cleaning out, wetting, grouting with cement slurry in CM 1:3, complete all as specified and directed.

Screed bed or bedding layer of 10 mm thick in cement mortar 1:4 over roof slab mixed with water proofing compound all as per manufacturer’s instructions, finishing the surface even and fair, complete all as specified and directed. NOTE:- Water proofing compound shall be measured and paid separately as 'Supply only' under respective items of this Schedule.

Plain cement concrete 1:3:6, type C-1( using 20 mm graded crushed stone aggregate) as in roof padding and leveling course, benching etc, finished even and rough to receive cement mortar screed bed, complete all as specified and directed.

Cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed, with grey cement and no pigment; set, jointed and pointed in neat cement slurry as in floors, laid over and including provision of 15mm thick screed bed in cement mortar 1:4, complete all as specified and directed.

Ordinary rat tail rod, 300 mm mild steel, pattern spring including roller and roller plate, complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 metre in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc., not exceeding 10 sq.m on plan and not exceeding 1.5 metre in depth and getting out in soft / loose soil, complete all as specified and directed.

Plain cement concrete 1:4:8 type D2 (40mm graded stone aggregate) in foundations, filling and mass concrete, complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) of any section, embedded in concrete, brickwork or masonry etc., including taking out embedded portion and making good disturbed ground, complete all as specified and directed.

Dismantling fencing wire mesh, any type, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Exterior grade digital series elevation tiles as in vertical surface of walls such as skirting / dado etc., size of tile shall be 450mm x 300mm x 7mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles, laid over and including provison of 10 mm thick rendering as in backing of tiles in cement mortar 1:4, complete all as specified and directed.

Returning, filling in (in soils), including spreading, levelling, watering and well ramming in layers not exceeding 25 cm, complete all as specified and directed.

Removing surplus excavated material (soils) to a distance not exceeding 50metre and depositing where directed at a level not exceeding 1.5 metre above the starting point, complete all as specified and directed.

Taking down copper/ aluminium point wiring of any type, size and description (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. to match with the existing, complete all as specified and directed.

Taking down main switches, DBs, cut-outs of any type alongwith existing boards and removing the same from site and making good disturbed surfaces of walls to match with the existing, complete all as specified and directed.

Taking down carefully submain wiring of any type and size including earth wire on wooden batten / surface conduits / casing and caping etc., and removing the same from site and making good disturbed surfaces of walls to match with the existing, complete all as specified and directed.

Point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 1.5 sq.mm (nominal area) FR type multi stranded copper conductor, single core drawn in and including not less than 20mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories controlled by one, one way switch, including concelad pressed steel terminal box of required size and not less than 1.6mm thick factory made duly painted inside and outside with two coats of black bituminous paint over and including a coat of red oxide primer, with 3.0 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc, including 1.5 sq.mm FR type PVC insulated unsheathed cable multi stranded copper conductor as continuous earth wire and connected to earth dolly as required at site and including chases cutting and making good the disturbed surface and applying finishes to match the existing surface, complete all as specified and directed for following:-

One light / fan /exhaust fan point controlled by one one-way 5 Amp switch

One 3/5 pin, 5 Amp socket outlet point on an independent board.

One 5 pin, 5 Amp socket outlet on the same board with other switches

One bell / buzzer point controlled by one bell push single pole one way switch

One light point controlled by one 5Amp two-way switch

Point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 2.5 sq.mm (nominal area) FR type multi stranded copper conductor, single core drawn in and including not less than 20mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for one 6 pin 15/16 Amps socket outlet point on an independent board, including concelad pressed steel terminal box of required size not less than 1.6mm thick factory made duly painted inside and outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 3.0 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc, including 2.5 sq.mm FR type PVC insulated unsheathed cable multi stranded copper conductor as continuous earth wire and connected to earth dolly as required at site and including chases cutting and making good the disturbed surface and applying finishes to match the existing surface, complete all as specified and directed.

Switch piano, flush type single pole, one way 5/6 Amp 230 volts, complete all as specified and directed.

Switch piano, flush type single pole, two way 5/6 Amp 230 volts, complete all as specified and directed.

Socket outlet, 2 in 1, 3/5 pin, 5/6 Amps 230 Volts, flush type, complete all as specified and directed.

Switch piano, flush type single pole, one way 15/16 Amp 230 volts, complete all as specified and directed.

Socket outlet, 2 in 1, 6 pin, 15/16 Amps 230 Volts, flush type, complete all as specified and directed.

Lamp holder, PVC / polycarbonate body with back plate/ cord grip cap suitable for batten / angle/ pendent fittings, complete all as specified and directed.

Ceiling rose, single phase, PVC / polycarbonate, insulated body, three terminals, surface bakelite sheet 63.5mm dia, complete all as specified and directed.

Bell push piano, flush type, single pole, one way 5/6 Amp 230 V, complete all as specified and directed.

Electric bell ding dong type AC 230 Volt 50 Hz single pole, complete all as specified and directed.

Ceiling fan regulator flush type, electronic, rotary stepped type, AC 230 V, suitable for 1200/1400 mm sweep ceiling fan, complete all as specified and directed.

Sheet metal enclosure for MCB DBs SPN, 8 way, double door, vertical type, 240 V with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way, fixed in repair, complete all as specified and directed.

MCB SPN, 6 to 32 Amp, 240 Volt, conforming to 'C' curve, 10kA breaking capacity, complete all as specified and directed.

MCB SP 6 to 32 Amp, 240 Volt, conforming to 'B' curve, 10kA breaking capacity, complete all as specified and directed.

LED mirror light fitting, 1x9W, LED 6000 K, decorative indirect up-down light for mirror and as wall light application with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. MAKE:- Havells IVORY Model No. LHESABP7IN1W009 or techno-commercially equivalent model in Philips / Crompton / Bajaj

LED bulk head light fitting, 1x10W, LED 600 lumen, enclosed in polycarbonate body, weather proof, LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. MAKE:- Phillips ENDURA Model No. WT202W LED6S CW PSU S1 PC or techno-commercially equivalent model in Havells / Crompton / Bajaj

LED wall mounted tube light fitting, 1x18W, LED 6000K, decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. MAKE:- Havells Model No. LHEXBHP7IN1W018 or techno-commercially equivalent model of Phillips / Crompton / Bajaj

Decorative wall light fixture made up of Polycarbonate, suitable for 15W TU retrofit CFL (B-22 base), enclosed in polycarbonate body, weather proof, LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. MAKE:- Havells Cat No. CITY 4, LHFODFE1TC1W015 or techno-commercially equivalent model in Philips / Crompton / Bajaj

Building security light lighting luminarie 36 Watt, with unique peanut optics to ensure uniform distribution, higher spacing between poles and maintenance free system for city roads and streets, 50% energy savings, IP66 Protection PC and FG cover, high impact resistance complete including LED lamps and all accessories including bracket made out of 25mm bore GI pipe (light grade), 1.20m long made to shape and fixed to existing pole or building by means of 2 Nos MS flat iron 40x6 mm clamps with suitable size bolt, nuts & washers and connecting with 3 core flexible copper wire of size 23/0.0076 from ceiling rose to existing junction box, complete all as specified and directed. MAKE:- Bajaj Cat No. BRLEP36WLEDWH or Havells Cat series CITYLITE Platinum Plus or techno-commercially equivalent model in Crompton / Philips

Earthing complete with GI earth plate electrode 600mm x 600mm x 6.3mm thick buried directly in ground vertically to a depth of not less than 2.25m deep below ground level with the top edge of earth plate at a depth of not less than 1.5m below ground level connected to GI earth lead of 4mm dia by means of bolts, nuts, washers of galvanised iron or steel, GI earth wire shall be protected by 20mm dia GI pipe 'medium grade', watering pipe 20mm dia GI pipe 'light grade', GI wire meshed funnel, alternate layer of charcoal and salt on all side to earth plate upto a thickness of 150mm, filling of black cotton soil in earth pit upto GL and connected to earth plate including necessary excavation and earthwork, PCC 1:3:6 type C-1 earth chamber, 40mm thick RCC cover 1:2:4 mix with 6mm dia nominal reinforcement @ 150mm c/c both ways etc complete all as shown in electrical plate No.3 connected to earthing test point, including testing on completion, complete all as speciifed and as directed. NOTE:- (a) Rate quoted shall deemed to include cost of excavation in any type of strata, RFR and removal upto 50metre, PCC pit, funnel and RCC cover plate. (b) If earth resistance is not found satisfactory, till satisfactory test result comes, the same shall be redone by the contractor without any extra cost to department.

Sub main wiring complete with 2 runs of 4 sq.mm PVC insulated and unsheathed 1100V grade multistranded FRLS grade copper conductor cable drawn through and including provision of PVC rigid conduit 20mm dia and accessories connecting terminal ends to DB's including providing 1 run of 4 sq.mm PVC insulated unsheathed multistranded FRLS grade copper cable as earth continuity conductor and connecting to common earth dolly, complete all as specified and directed. NOTE:- (i) Two runs of 4 sq.mm copper conductor, one run of 4 sq.mm copper earth continuity conductor and one run of PVC rigid conduit and with accessories shall be measured as one unit length. (ii) Extra length of cable / wire required for connection to MCBs shall not be measured and the rate quoted per unit shall deemed to be inclusive of the same accordingly.

Taking down carefully ceiling fan / exhaust fan keeping in safe custody, cleaning and servicing the fan including painting with one coat of synthetic enamel paint and marking MES No. refixing in original position including replacement of three core 23/0.0076 copper conductor, complete all as specified and directed.

Taking down carefully geyser keeping in safe custody, cleaning and servicing the same including painting with one coat of synthetic enamel paint and marking MES No. refixing in position including replacement of three core 23/0.0076 copper conductor, complete all as specified and directed.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 20 to 32 Amps, 'C' series, 10kA capacity, complete all as specified and directed.

Mohit Enterprises

Ram Babu Bros

R K GUPTA AND SONS

K L KALSI

vs construction

KRISHNA BAHADUR