ADDN ALTN AND MODERNIZATION OF 03 X RECRUIT AGNIVEERS COOK HOUSE AT TRG BN 2 DIGHI CAMP BEG AND CENTRE KHADKI UNDER GE CENTRAL KHADKI

Amount

Demolition of stone slabs/flooring of any description laid bedded and pointed any mortar all as specified and directed.

M&L for Kota stone slab flooring 20-25 mm thick laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing & including 15 mm thick screed bed in cement mortar (1:6) all as specified and directed.

All as per ser item No 2 above but on step riser, skirting laid over and including 10mm thick rendering in CM (1:4) all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles in store and rubbish of the premises outside of MD land all as specified and directed.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over & including 15 mm thick screed bed in cement mortar (1:6) all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surface 450 X350X7 or 600X300X7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles including 10 mm thick cement plaster in CM (1:4) as backing coat all as specified and directed.

Taking down chowkhats or frame with shutter (without taking off shutter from the frames) & removing from site area exc. 1.5 Sqm but n. exc. 4 Sqm each all as specified and directed.

All as per item No 07 above but area n.exc. 1.50 sqm each all as specified and directed.

Taking down shutters of any description area exc. 1.0 sqm but not exc. 2.0 sqm each all as specified and directed.

S&F pressed steel door frames of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plates all as specified and directed by Engr-in-charge

All as per item No 10 above but of size 125 x 60 mm all as specified and directed by Engr-in-charge

M&L PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) in door frame filling all as specified and directed.

S&F factory made 35 mm thick plain framed panelled shutter (single panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm veneered particle board with Commercial veneered on both faces, the size of rail and style as per IS-1003 ( Pt-I) kiln seasoned and Chemically pressed of 2nd class hard wood all as specified and directed by Engr-in-charge

S&F factory made 35 mm thick glazed & skeleton shutter of 2nd class hard wood open rebated and prepared to receive gauge (divided into squares with sash bars) edges of framing plain chamfered or rounded, fitted without & fitted beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I Sec-8 clause 8.23 (a) and fitted to chowkhats all as specified and directed by Engr-in-charge

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown on Page No. 160 of SSR 2010 part II.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as a gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitabe PVC sheet beading, and joined together with solvent cement, supplying & fixindg in the frame at site as per specifiction & drawing.

S&F Butt Hinges medium weight cold rolled mild steel 100 mm long all as specified and directed.

S&F 150mm long Aluminium anodized, barrel tower bolt of extruded section all as specified and directed.

S&F Aluminium anodised, barrel tower bolts of 100mm length,of extruded section all as specified and directed.

S&F Extruded aluminium alloy handles 150 mm, fabricated type, anodised all as specified and directed.

S&F 300 mm long mild steel sliding door bolts, plate type, with stainless steel bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate all as specified and directed.

S&F 200 mm long mild steel sliding door bolts, plate type, with stainless steel bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate all as specified and directed.

M&L for Granite slab machine cut for 20 mm thick bedded and jointed with colour cement to match the shades of the granite cut to shape required as in Kitchen platform, serving platform, Cuboards, etc all as specified and directed.

M&L for Machine cut cudappah stone slab 20-25mm thick laid over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including M&L for screed bed or bedding layer 15 mm thick in cement mortar (1:6) for laying floor finishes all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations all as specified and directed.

M&L for black Granite Work 18 to 20 mm thick, table moulded, rubbed and polished as in steps, jambs, pillars, window- cills and like laid over 15mm thick cement screed base in CM (1:4) including pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of slab rubbing, polishing and rounding to edges all as specified and as directed.

S&F Waste coupling Pop-Up Type, chrome Finish Full Thread Waste Coupling 32mm, with Push Down Stainer all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe including bedding in cement mortor to dwarf wall or cantilever brackets and connecting union to pipe overall size 915x460mm and bowl size 410x330x160mm all as specified and directed.

M&L 15mm dia medium grade Galvanised iron tubing with all fittings and fixed to wall, ceiling or laid in floors all as specified and directed.

M&L 20mm dia medium grade Galvanised iron tubing with all fittings and fixed to wall, ceiling or laid in floors all as specified and directed.

M&L for preparing plastered or unplastered old surfaces of wall including brooming down or scraping down with steel wire brushes, smoke soot, moulds, moss efflorescent salts and trading oil and greasy spot and applying two coats of oil bound distemper all as specified and directed

M&L for preparation of old plasterd or unplastered surfaces of wall and applying two coats of cement base paint all as specified and directed.

M&L for preparing of old plastered or unplastered surfaces of walls including brooming down or scrap down with steel wire brushes, smoke soot, moulds, moss efflorescent salts, trading oil, greasy spot and applying three coats of white wash on ceiling all as specified and directed.

M&L for wall care putty of 1 mm thick as in interior / exterior on wall / ceiling surfaces of any description and finished surfaces smooth and even all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description exceeding 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of old painted steel surfaces of any description exceeding 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified and directed.

S&F in repairs 15 mm bore Pillar taps, cast copper alloy fancy type, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as specified and directed.

S&F in repairs angle cock cast copper alloy chromium plated fancy type with crutch or butterfly handle screwed down, screwed both ends for iron pipe or for brass ferrule for 15 mm bore of pipe all as specified and directed.

S&F PVC connections 15 mm size with PTMT nut of length 600 mm all as specified and directed.

S&F in repairs Bib taps 15mm dia, cast copper alloy chromium plated, with CP flange all as per Prayag Cat No 7306 Tranquil series or techno commercially equivalent makes specified in PS all as specified and directed.

S&F in repairs Vitreous china wash basin white flat back size 550x400 mm excluding taps but including 32 mm dia CP waste fitting and PVC waste pipe 610 mm long and brackets all as per makes specified in PS all as specified and directed.

S&F in repairs Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC(SWR) 'P' or 'S' trap connecting to flush pipe and to anti syphonage pipe all as per makes specified in PS. including making good to floor all as specified and directed.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, 10 Litre capacity, low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, all as per makes specified in PS all as specified and directed.

S&F in repairs 75mm bore PVC(SWR) pipe, type 'B' single socketed in any length with rubber ring joints laid in trenches or floors all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints fixed to wall including PVC clamps and necessary fittings all as specified and as directed.

S&F PVC (SWR) bends type 'B' of any radius, 75 mm dia all as specified and directed.

S&F PVC (SWR) bends type 'B' of any radius, 110 mm dia all as specified and directed.

S&F 75 mm bore PVC (SWR) branch piece (single Y), type 'B' equal or unequal with access door all as specified and directed.

S&F 110 mm bore PVC (SWR) branch piece (single Y), type 'B' equal or unequal with access door all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) WC connector type 'B' of any type all as specified and directed.

S&F in repairs PVC (SWR) gully trap 125/110mm setting and jointing in solvent cement all as specified and directed.

S&F in repairs 100 mm bore Cast iron Nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed.)

S&F in repairs Stainless steel plate rack of size 900 x 700mm, including provision for storage of plates and boxes fixed to wall all as specified and directed.

Demolition of precast concrete block masonry walling built in cement mortar as in manhole including PCC coping all as specified and directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed (below or above GL)

M&L Precast cement concrete block masonry using 1:3:6, type C1 (using 20 mm graded crushed stone aggregate) with solid blocks, exc. 10 cm in width and setting in mortar1:6 all as specified and directed.

M&L rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces and finishing the surfaces even and smooth without using extra cement including 3% WPC all as specified and directed (WPT shall be measured separately).

Supply only integral water proofing compound.

M&L for rendering 10 mm thick on fair faces of brick work /PCC block masonary or concrete surface of wall using cement plaster 1:6 and finished surfaces even and smooth without using extra cement all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of cement base paint over one coat of alkali resistant primer all as specified and directed

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of primer all as specified and directed

M&L 75 mm thick PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) in sub base to floor or as in Plinth protection all as specified and directed

Removing of old water proofing treatment and cleaning the surface of slab and clearing with wire brushes, removing dust, foreign materials, rubbish off the site to a distance n exc 100 m all as specified and directed by Engr-in-Charge.

M&L for water proofing treatment over RCC slab by applying oil based bituminous primer surface @ 0.25 kg/sqm and laying 3 mm thick APP modified water proofing polymeric membrane with 100 mm side and end lap having weight not less than 3.5 kg/sqm reinforced with non woven polyster reinforced mat weighting not less than 160 gms/sqm polyster core having soften point not less than 1500C, longitudinal tensile strength not less than 650N/5cm, by torching method and applying a coat of solar reflective alumunium paint @ 0.15kg/sqm on membrance surface including 24hrs ponding test all as specified and directed by the Engr-in-Charge

M&L for 10mm thick rendering in CM (1:3) on RCC roof slab mixed with water proofing compound @ 3% mixed with by weight of cement, finishing surfaces even and smooth to receive water proofing treatment complete without using extra cement for water proofing treatment over RCC slab all as specified and directed by Engineer-in-Charge. Note :- WPC shall be measured and paid separately.

S&F in repairs rotational moulded polyethylene water storage tanks three layer having capacity 2000 litres (cylindrical vertical with closed top ) hoisted and fixed in position including dismantling and removing of old tank complete all as specified and as directed. Note:-ISI mark should be embossed on tank. MAKE SYNTEX/PLASTO or techno commercially equivalent

M&L for 25 mm thick PCC 1:2:4 using Type B1 (using 20 mm graded crushed stone aggregate) as a leveling course for receiving floor tiles all as specified & directed

S&F powder coated aluminium sliding windows having three Nos of tracks including one guazed shutter for mosquito proofing including stainless steel wire cloth of 0.63 mm nominal dia and average aperature 1.4 mm and two Nos of glazed shutters including 4mm thick coloured glass and aluminium section weight not less than 0.55 Kg/RM for shutter and not less than 2.3 Kg/RM for frame including necessary cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, suitable handles, locking arrangement and fixed to stone masonry wall all as specified and directed by Engr-in-charge

Supply and fixing powder coated aluminium door made out of hollow extruded aluminium section as mentioned below: Each door having 02 Nos disc or D type handels, 02 Nos aluminium tower bolts 200 mm size one aluminium sliding door bolt or 250mm size, one brass mortice lock of six levers with key in duplicate regulated by double action hydraulic floor door spring (Make Sandhu/TITZ) shutter to be partly glazed with 5 mm thick tinted glass and partly panelled with 12 mm thick pre laminated particle board fixed with glazing clips, rubber beading/gasket anodized aluminium beading screws complete all as specified and directed by Engr-in-charge Chowkhat Frame : 101.60x44.45x1.55 mm Shutter verticle/stile: 85.00x44.45x1.56 mm Shutter middle rail : 83.50x44.45x1.54 mm Shutter top and bottom rail : 110x44.45x1.54 mm Make (i) Anodized aluminium section : Jindal/Hindalco, Indalco (ii) Particle board : Novapan, Duratuff (iii) Glass : Saint, Gobain, Modi Guard, TATA

S&F powder coated anodised aluminium ventilator shutters, fixed type without sash bar including stainless steel wire cloth of 0.63 mm nominal dia and average aperature 1.4 mm, aluminium section weighing 0.55 kg/m for shutter and not less than 1.052 Kg/RM for frame including lovered glass, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc.and fixed to stone masonry wall including demolition of RCC jali ventilators complete all as specified and directed by Engr-in-charge

Demolition of cement concrete in ground floor and paving n. exc. 15cm thickness below or above G. level all as specified and directed.

M&L PCC (1:4:8), type D2, (using 40mm graded crushed stone aggregate) as in sub base to floor 100mm thick all as specified and directed.

M&L Chequered cement concrete tiles rubber moulded 30cm x 30cm x 25mm thick, set, jointed and pointed in near cement slurry in floors, with grey cement and pigments over and including 15 mm thick screed bedding in CM 1:6 all as specified and directed .MAKE:- ULTRA/vaishnavi and techno commercially equivalent.

M&L for PCC 1:2:4 Type B-1 (using 20 mm graded crushed stone aggregate) in coping including necessary formwork and benching in bottom of manholes drain all as specified and directed..

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m in depth; for foundation etc or for manholes, laying pipes etc and getting out in hard / dense soil all as specified and directed.

Demolition of reinforced cement concrete manhole covers n. exc. 15cm thickness below or above G. level all as specified and directed.

M&L for cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone coarse aggregate) as in concrete bed to drain pipes including packing under & haunching against sides of pipes after they are laid and tested for 200 mm bore pipe all as specified and directed.

M&L PCC (1:4:8) type D - 2 (using 40 mm graded crushed stone coarse aggregate) in foundations filling & mass concrete all as specified and directed.

M&L reinforced concrete pipes, 200 mm bore, Class NP-2, laid and jointed complete with collars all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends all as specified and directed.

All as per item No 80 above but add or deduct for each 25 mm girth or part thereof over or under 30cm .

Returning, filling in including spreading, levelling, watering and well ramming in layers n. exc. 25 cm in hard / dense soil all as specified and directed.

Removing excavated soil n. exc. 50m and depositing where directed at a level n. exc. 1.5 m above the starting point all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone coarse aggregate) in cover slab set in CM 1:6 all as specified and directed.

M&L mild steel TMT bars 8 mm dia, cut to length, bend to shape required, including cranking, bending and binding with mild steel wire (annealed) not less than 0.9 mm dia all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers n. exc. 25 cm in hard / dense soil all as specified and directed.

Removing excavated soil n. exc. 50m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for framed work such as grills etc with ends of bar shouldered and or revetted or forged into spikes framed guard bars including framed flat iron of any size and section to combined the grills all as directed by Engineer-in-Charge.

Taking down copper/aluminium point wiring ( light, fan, bell, socket, power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets etc. and removing materials to store for keeping in safe custody for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors all as specified and directed.

Taking down carefully submain wiring of any size all as specified and directed.

Taking down DB including MCCB/MCB of any type and size all as specified and directed.

M&L for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing caping of required size with all fittings and accessories alongwith one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one light point or one fan point controlled by one, one way switch including PVC switch board of required size or 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on existing MS concealled box for mounting of switch, regulators or bell push and casing caping terminal box for mounting ceiling rose/ holders all as specified and directed.

All as per item No 92 here-in-before but 5 amps socket point independent all as specified and directed.

All as per item No 92 here-in-before but 5 amps socket point on same board as specified and directed.

All as per item No 92 here-in-before but cable of size 2.5 sqmm for one 16 amps socket (Power) point independent all as specified and directed.

M & L for surface submain wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 4 sqmm (Nominal area) drawn through in and including PVC casing caping/PVC conduit size with all fittings and accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly incl dismentling taking down old unserviceable wiring and making good to disturbed surfaces all as specified and directed. NOTE: (a) Two run of cable with one run of earth wire and one run of casing capping/conduit will be measured as one length.

Supply and Fixing Submaiin wiring with 6 sqmm 4 runs of single core multi stranded PVC insulated unsheathed copper conductor cable fire retardent 1100 Volts drawn in and including 25mm dia ISI marked PVC conduit with all accessories such as tees, elbows bend, junction box, reducers etc as required alongwith one run of 1x 6 sqmm single core PVC insulated unsheathed copper conductor cable as continuous earth wire and connecting to Existing main switch board/Distribution Board and testing on completion complete all as directed by Engineer-in-Charge. Note:- 4 runs of 6 sqmm wire 1 run of 6 sqmm PVC insulated, unsheathed, single core multy standed copper conductor cable and 1 run of 4 sqmm and PVC conduit 25mm dia shall be measured as a single run.

S&F 5 Amp switch piano type single pole one way all as specified and as directed.

S&F socket outlet flush type 6 amps, 5 pin, 230v all as specified and as directed.

S&F switch socket combination multipurpose 2-in-1 flush type 6 amps, 230 v all as specified and as directed.

S&F switch socket combination multipurpose 2-in-1 flush type 3 pin 16 amps and 3 pin 6 amps, 230v all as specified and as directed.

S&F lamp Holder insulated body with back plate for batten fitting all as specified and as directed.

S&F LED tube light batten fitting, 20 watt, CDL, 230 Volts, 4 feet long, complete with all accssories internally pre wired and including connecting up to ceiling rose with 0.5 sqmm twin core copper flexible conductor cable including LED lamp and mounting casing box 2 nos fitting any type all as specified and directed. Make- shakti Cat Part No CCS-10CCS-100-20-65-HL2-DP-NWH or equivalemt in any Make.

S&F ceiling rose surface Bakelite three terminal all as specified and as directed.

S&F flush type electronic fan regulator with 5 step type,120 W, AC 240 Volts, 50 Hz all as specified and as directed.

S&F in repairs MCB, Single Pole, 6 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve all as specified and directed.

S&F in repairs MCB, Double Pole, 6 to 32 amps, 415 Volts, 10 KA breaking cap, ‘’C” all as specified and directed.

S&F in repairs MCB, TP , 6 to 32 amps, 415 Volts, 10 KA breaking cap, ‘’C” curve all as specified and directed.

S&F in repairs MCB, Four Pole, 40 to 63 amps, 415 Volts all as specified and directed.

S&F in repairs Vertical MCB distribution board, as MCB TPN incomer, IP 43 protection, Double door, metal enclosure, TPN, 415 Volts, 4 way all as specified and directed by Engr-in-Charge.

S&F in repairs MCB distribution board, Double door, metal enclosure, SPN, 230 Volts, 8 way all as specified and directed by Engr-in-Charge.

S&F in repairs ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1400 mm sweep. Min air delivery 245 CFM with service value 6.0 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by Engr-in-Charge. Note - Old UNSV ceiling fan deposit to MES store

S&F in repairs exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers incl making of suitable hole in brick / stone wall for fixing of Exhust Fan complete all as directed by Engineer-in-charge. Note - Old UNSV Exhaust fan deposit to MES store

S&F DOL motor starter 3 HP capacity 2.2 KW conforming to IS 13947-4 all as specified and directed.

S&F stainless steel wall mount type exhaust hood made out of 1mm thick stainless steel plate. Size of hood 08 feet x 03 feet x 02 feet hight all as spesified and directed by Engineer-in-Charge

Supply, fabrication and fixing of stainless steel ducting made out of 22 SWG stainless steel sheet, angle iron frame with stainless steel bolt, nut 25x3mm thickness to the Exhaust system all as directed by Engr-in-Charge.

S&F with fabrication 3HP centrifugal blower motor 1440 RPM, 03 phase to exhaust system made out of by stainless steel sheet with 22 SWG all as directed by Engr-in-Charge.

Cutting chases, pinning in and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth Brick wall or PCC hollow block all as specified and directed by Engr-in- charge.

Commissioning and testing of electric chimmey/ Extractor hood steel equipped and exhaust system including all accessories of system all as directed by Engr-in-Charge.

S&F Metal plug and socket board with MCB SP 20 amp, 16 KA. all as specified and directed.

M&L Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire all as shown in Plate No. 2 to the earthing test point all as specified and indicated including testing on completion

Sunbud Multiventures Private Limited (BID ID -3458272)

BSK Construction (BID ID -3458207)

L.K.R.TIWARI CONSTRUCTION (BID ID -3452950)

shrilaxminarayan constructions (BID ID -3457960)

S.R.M.K Enterprises (BID ID -3453324)

ShreHari Civil Enginneering and Contractors (BID ID -3453523)

H S TAKHI (BID ID -3453414)

Suchit constructions (BID ID -3457514)

MAHESH DADAJI BACHHAV (BID ID -3458004)

UNIQUE ENGINEERS (BID ID -3453534)

United Sales Corporation (BID ID -3457745)

Bidder Name

H S TAKHI

United Sales Corporation

V.R.PRAJAPATI AND CO.

BSK Construction

UNIQUE ENGINEERS

S.R.M.K Enterprises

L.K.R.TIWARI CONSTRUCTION

MAHESH DADAJI BACHHAV

shrilaxminarayan constructions

Suchit constructions

Sunbud Multiventures Private Limited

ShreHari Civil Enginneering and Contractors