ADDN/ ALTN TO BUILDING NO O7/11, O7/02, O7/8, BUILDING NO O5(L) AND PROVN OF PARTITION WITH DOOR FOR TOs ROOM INSIDE VIJAY DURG UNDER GE (FW) KOLKATA

Amount

(B/R PORTION) Taking down cement plaster in any description on brick or stone wall etc incl racking out joints. hacking for key scrubbing down with water etc complete all as specified and directed.

M&L rendering 15 mm thick cement plaster in two layer each of 10+5 mm thick on fair face of brick work or concrete surface on external surfaces in CM (1:4) & water proofing compound mixed with second layer @ 250 ml/Bag or as per manufacturer instruction finished fair and even. complete all as specified and directed. (Note -W.P.C. shall be measured and paid separately.)

Supply only integral water proofing compound all as specified and as directed.

M&L for 15 mm thick rendering in CM (1:6) on other than fair face of brick or concrete surfaces on internal surfaces finishing even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10 mm thick in CM 1:3 on ceilings finished even and smooth without using extra cement (up to ceiling height of 6 to 7m )incl necessary arrangements for execution of the work) all as specified and directed.

Dismantling Structural steel wok incl grills ,gates, stair case etc but excluding framed truss in any position complete all as specified and directed.

S & F mild steel in framed work such as grills, gratings, etc. with ends of bars shouldered and /or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and directed .

M&L mild steel rolled sections as in main and cross beams, angle, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors etc conforming to grade Fe-410- W (Gde- E- 250) quality- A made to required shape and size, welded at joints complete all as specified and directed

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 including necessary form work complete all as specified and directed.

S&F mild steel Framed work as in doors or sliding gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe-410-W(Gde-E-250) quality-A all as specified and directed

S&F rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe-410-W (Gde-E-250) quality-A complete all as specified and directed.

S & F pre-painted Galvalume aluminium zinc coating GI based corrugated steel 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges , valley gutter, Sun shed etc fixed with self tapping screws as specified.

M & L applying two coats of synthetic enamel paint on steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of surfaces complete.

Cutting holes in brick walls in cement mortar for inserting holdfast or pipes and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required exc half brick but not exc one brick, etc complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins arches pillars etc complete all as specified and directed.

M&L for brick work with fly ash bricks (with Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L brick work with fly ash bricks, (with Old Size Bricks),straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Demolition of reinforced cement concrete of any description for Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended slabs complete all as specified and directed.

Formwork Use and waste to sides and soffits and suspended slabs n. exc. 200 mm thick and similar works fair finished surfaces of concrete complete all as specified and directed.

M&L For RCC 1:2:4 type B1 20 mm graded as in chajja, slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

S & F mild steel TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S & F mild steel TMT bar 6 to 8 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

M&L for complete removal of existing treatment of old wall surface and applying two coats of oil bound distemper over a coat of alkali resistant primer applied over 1 to 2mm thick water proof wall care putty complete all as directed by Engr-in-charge.

M&L for preparation of new wall surface and applying two coats of oil bound distemper over a coat of alkali resistant primer applied over 1 to 2mm thick water proof wall care putty complete all as directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for all as specified and directed.

M & L 25 mm thick PCC 1:2:4 type B-1 using 12.5 mm graded stone aggregate as in flooring, laid in alternate bays, surface finished even and smooth using without extra cement complete all as specified and directed.

M & L 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring, laid in alternate bays, surface finished even and smooth using without extra cement complete all as specified and directed.

M & L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of floor complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M & L for 20 mm thick screed bed or bedding layer of mortar as in backing coat of stone on fair face of brick wall or concrete surface in cement mortar 1:4 complete all as specified and directed.

M & L 18 to 20 mm thick machine cut one side polished natural hard stone (Granite)any type in step, jambs, pillars, window cills, cooking plate from and similar places etc like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Supply and fix non skid ceramic light coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but n exc 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles over and incl 15 mm screed bed in 1:6 complete all as directed.

Supply and fix non skid ceramic light coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but n exc 0.38 sqm in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles over and incl 10 mm rendering in CM 1:3 complete all as directed.

M & L glazed ceramic colour tiles size 450 mm x 300 mm x 6 to 7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match including 10 mm thick backing layer in cement mortar 1:3 complete all as specified and directed. complete all as specified and directed.

M&L Vitrified ceramic joint free colour tiles area of each tile exc 0.42 Sqm but n exc exc 1.0 Sqm and 9 to 10 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement complete including 15 mm thick screed bed cement mortar 1:6 complete all as specified and directed. all as specified and directed .

M&L Vitrified ceramic joint free colour tiles for Vertical surface of area of each tile exc 0.42 Sqm but n exc exc 1.0 Sqm and 9 to 10 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement complete including 10 mm thick screed bed cement mortar 1:3 complete all as specified and directed. all as specified and directed.

M & L for heavy duty coloured ceramic floor tiles of size 300 x 300x 10 mm thick, suitable for high traffic external tiles, anti skid, scratch resistance and neutral to UV rays and acid alkali resistance as in floor including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Supply and Fixing PVC solid wall lining consisting of 5 mm thick plain colour PVC sheet used inclusive of solvent cement and fixing at site on PVC frame as per manufacturer’s specification and instruction) directed.

Supply and Fixing PVC fillets of width 35 mm, made of 5 mm thick PVC sheet, for wall panelling inclusive of fixing as in grid / frame on wall at a distance .6m horizontal & vertical for wall lining/panelling as per specification of manufacturer and as directed .

Fixing only old Joist, channel angle of beams etc cutting with suitable size complete all as specified and directed.

M&L welded steel wire fabric, weight n exc 4 kg per square meter complete , fixed to steel members, all as specified and directed.

S&F 0.8-0.9 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required all as specified and directed.

M & L 18 to 20 mm thick machine cut Pre Polished Kota stone slab flooring ,stair case step etc over screed bed base ,laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M & L 18 to 20 mm thick machine cut Pre Polished Kota stone in riser of steps, skirting, dado and pillar laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing with & including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for 8 mm thick moisture resistant high density fibre board (HDF) interlocking floor planks AC 5 Grade with highly wear resistant protective layer of aluminium oxide of approved design/pattern, fixed over 2000 Micron EPE foam layer over 200 micron polyethylene sheet with corner edge bidding complete all as per manufacturer's instruction all as specified and directed.

Taking down chowkats or frames with shutters (w/o taking off shutters from the frames) area exceeding 1.5 sqm and not exceeding 4 sqm each and removing from the site complete all as directed .

S &F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F stainless steel butt hinges 100mm medium weight all as directed.

S&F 300mm Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section all as directed complete all as directed.

S&F 150 mm Extruded brass handles, fabricated type polished all as specified

S&F 300 mm Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed all as specified.

S&F 300 mm Stainless steel handles, fabricated type polished required as per site all as specified

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets all as specified.

M&L False ceiling with 'E' board "Classic" , reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium powder coated snap grid to support the boards/files with aluminium anodised main 'T' section 36mm x 25mm x 1.40mm cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides including hanging arrangements with 1.6mm dia GI wire and anodised adjuster and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete as in repair, all as specified and as directed

M & L 75 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in flooring, laid in alternate bays, surface finished even and smooth using without extra cement complete all as specified and directed.

M&L Vitrified ceramic joint free colour tiles area of each tile exc 0.18 Sqm but n exc exc 0 .36 Sqm and 7 to 8 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement complete including 15 mm thick screed bed cement mortar 1:6 complete all as specified and directed. all as specified and directed.

M&L Vitrified ceramic joint free colour tiles for Vertical surface of area of each tile exc 0.18 Sqm but n exc exc 0 .36 Sqm and 7 to 8 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement complete including 10 mm thick screed bed cement mortar 1:3 complete all as specified and directed. all as specified and directed.

M& L roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

Material and labour for brushing neat cement slurry with 3.0 kg of cement per sq metre complete all as specified and directed.

M&L non skid endura joint free colour stepping tiles area of each tile exc 0.18 Sqm but n exc exc 0 .36 Sqm and 15 mm thick, Stair tread steps tiles etc, set and jointed in neat cement slurry and pointed in coloured cement complete including 15 mm thick screed bed cement mortar 1:6 complete all as specified and directed. all as specified and directed.

M&L non skid endura joint free colour stepping tiles for Vertical surface of area of each tile exc 0.18 Sqm but n exc exc 0 .36 Sqm and 15 mm thick, in Stair riser etc, set and jointed in neat cement slurry and pointed in coloured cement complete including 10 mm thick rendering cement mortar 1:3 complete all as specified and directed. all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement all as specified and directed.

S&F 10 mm thick Toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes all as specified and directed.

M&L for applying two coats of oil bound distemper to old decorated (distempered) surfaces of ceiling including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed .

M&L for applying two coats of oil bound distemper to new plastered surfaces of ceiling including preparation of surface complete all as specified and directed .

M&L non skid ceramic colour tiles of area of each tile exc .06 Sqm but n exc exc .11 Sqm and 6 to 7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement complete including 15 mm thick screed bed cement mortar 1:6 complete all as specified and directed. all as specified and directed.

M & L glazed ceramic colour tiles size 600 mm x 300 mm x 6 to 7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement including 10 mm thick plastering in cement mortar 1:4 complete all as specified and directed. to match complete all as specified and directed.

S&F in repair chromium plated Hand shower (health faucet), brass body with 1.2 metre long flexible tube in chrome finish with wall hook complete all as specified and directed. (MAKE : JAQUAR, Cat No : ALD-573/ PARRYWARE, Cat No : T9941A1 / ESS ESS, Cat No: C-232D / CERA, Cat No: F8030401AB / HINDWARE, Cat No: F160002) or equivalent make specified in tender.

Supply and fix vitreous china wash basin, white, counter top, size 450 x 400 mm oval shape excluding taps, waste, chain and plug and porcelain stopper complete all as specified and directed.

S&F in repair Chromium plated brass Angular stop cock, fancy type, concealed type with wall flange fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No: CON-59KN / PARRYWARE, Cat No: G1453A1 / ESS ESS, Cat No: C-206 / CERA, Model: OCEAN / PRAYAG, Cat No: 9210 / HINDWARE, Cat No: F330043) or equivalent model in JAQUAR / CERA / PARRYWARE HINDWARE/PARRYWARE)

S&F in repair Chromium plated brass Wall mixer, concealed type, with concealed body, with overhead shower arrangement fixed with 15 mm bore Iron pipe including taking down existing mixer complete all as specified and directed. (Make : Jaquar, Cat No : CON-273KNUPR / PRAYAG, Cat No: 9275 / CERA, Model: OCEAN / PARRYWARE, Cat No: G1417A1 / HINDWARE, Cat No: F200020 / ESS ESS, Cat No: C-216) or equivalent model in JAQUAR / CERA / HINDWARE/PARRYWARE)

S&F in repair fancy type chromium plated telephonic hand shower with flexible tube and hook screwed for iron pipe including frame complete all as specified and directed. (Make : PARRYWARE, Cat No: T9983A1/ Ess Ess, Cat No: HS 105) / PRAYAG, cat No: BHS-91S / CERA, Cat No: F7030502 / HINDWARE, Cat No: F160053 ) or equivalent make specified in tender.

S&F in repair 15mm dia fancy type chromium plated basin mixer foam flow screwed for iron pipe incl taking down old all as directed by Engr-in-Charge. (MAKE : ESS ESS, Cat No : C-211A / JAQUAR, Cat No : CON-167KNB / PARRYWARE, Cat No: G1414A1 / CERA, Model: OCEAN / PRAYAG, Cat No: 9250 / HINDWARE, Model: CONTESSA PLUS) ) or equivalent make specified in tender.

S&F in repair 15mm bore chromium plated two way bib cock with flange, fancy type complete all as specified and as directed. (Make : Ess Ess, Cat No: C-203 / JAQUAR, Cat No: CON-041KN/ PARRYWARE, Cat No: G1434A1 / CERA, Model : OCEAN / PRAYAG, Cat No: 9212/HINDWARE, CAT No: F330004CP) ) or equivalent make specified in tender.

S&F Chromium plated brass Towel ring (premium quality) complete all as specified and directed. (Make : Ess-Ess, Cat No: AC-502 / JAQUAR, Cat No: ACN-1121BN / PARRRYWARE, Cat No: T6002A1 / PRAYAG, Cat No: BA-11 or equivalent model in JAQUAR / PARRAYWARE)

S&F toilet paper holder, surface type with flap incl taking down existing holder complete all as specified and directed. (Make : JAQUAR, Cat No : CAN-1153N / CERA, Cat No: F5007110 / PRAYAG, Cat No: BA-38 / ESS ESS, Cat No: AC-506 / HINDWARE, Cat No: F880003) or equivalent model in JAQUAR / CERA / HINDWARE/PARRYWARE)or Equivalent

Supply & fix, in repair brass chromium plated over head shower roses (200x200mm) with shower arm or without swivel joint, including fixing to steel pipe or union all as specified and directed(Make : CERA, Cat No: F7040103 (for arm) & F7020305 (for shower) / PARRYWARE, Cat No: T9802A1 (for arm) & T9986A1 (for shower)/ESS ESS, Cat No: OH-104A / HINDWARE, cat No: F160051) ) or equivalent make specified in tender.

S&F towel rack (premium quality) with lower hangar with hook incl taking down existing rack complete all as specified and directed. (Make : JAQUAR, Cat No: AHS-1581H / ESS ESS, Cat No: AC-308 / PARRYWARE, Cat No: T6008A1 / CERA, Cat No: F5003101 / PRAYAG, Cat No: BA-12) or equivalent make specified in tender.

S&F vitreous china floor mounted coupled closet (Pedestal pattern) white including low level vitreous china valve less symphonic action type flushing cistern with inlet ball valve float, push button, flush pipe incl bracket, P/S trap, PVC coloured seat cover and connecting fittings including taking down existing water closet complete all as specified and directed.

S&F corner glass shelf 200 mm with brass brackets, as in repair complete all as specified and directed. (Make: PRAYAG, Cat No: BEA-44 / JAQUAR, Cat No: ACN-1173 / PARRYWARE, Cat No: T6010A1 / CERA, Cat No: F5005102) or equivalent make specified in tender.

M&L preparation of surfaces and pasting of wall paper of any design/ pattern/ shade, complete all as specified.

S & F 10 to 12 mm thick gypsum board false ceiling including 0.55 mm thick GI perimeter channel, GI channel tray frame work having one flange of 20mm and another flange of 30mm with web of 27mm, fixed to surrounding wall using nylon sleeves and screws @ 450mm centre to centre / GI intermediate channel of size 45mm x 0.90mm thick with two flange of 15mm each suspended from the soffit of roof slab/ truss @1220mm c/c with MS angle of suitable size fixed to soffit of ceiling with GI cleat and expansion fasteners with and including ceiling section ( not exc 1.2 metre length ) of 0.55 mm thickness having kurled web of 50 mm and flange of 25 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel @ 457 mm centre to centre with necessary nuts and bolts and gypsum board screwed to ceiling section with stainless steel screws @ 230mm c/c including applying two coats of plastic emulsion paint over a coat of primer to exposed surfaces complete all as specified and directed.

Dismantling of old aluminium snap grid, framework in partition, door or in any position with all connection items all as specified and directed.

Refixing dismantled aluminium Partition obtain from item No 85 complete as specified and directed.

M&L for Vitrified Ceramic tiles 8 to10 mm thick light shade (of square shape) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer or mortar 15 mm thick for laying floor finishes in CM 1:4 all as specified and directed.

All as per item no 87 but using as skirting/dado including screed bed10 mm thick for wall tiling etc. in CM 1:3

S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified.

S&F factory made single extruded WPC (Wood polymer composite) solid door/ window / ceosetory windows & other frames/chowkats of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade) calcium carbonate and natural fibbers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (Face) & 1100N (Edge), minimum compressive strength of 58N/mm², modulus of elasticity 900 N/mm² and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge, (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note : For WPC solid door/ window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibbers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately).

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F 4.8 mm thick ordinary quality sheet glass/frosted glass and glazing with oil putty in square n.exc. 0.5 Sqm in each pane complete all as directed.

M&L solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, all as specified and directed

S&F Aluminium anodised sliding door bolts of 300mm long with hasp and staple(bolt type) and fixing clips of sheets cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F aluminum anodised barrel tower bolts of extruded section 150mm long complete all as specified and as directed.

S&F Butt Hinges medium weight cold rolled stainless steel 100mm long complete all as specified and directed.

Supply and fixed aluminium (die cast) body door closer hydraulically regulated designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces or un plastered surfaces of ceilings and applying one coat of white wash complete all as specified and directed.

(E/M PORTION) Taking down copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants , regulators, sockets etc excluding light fitting for taking credit removing from site and making good disturbed surface of walls, floors etc complete all as specified and directed.

Materials and Labour for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLS PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories, fixed to walls/ceiling, including mild steel terminal boxes 1.25 mm thick conforming to IS-5133 (Part-I) with 3.0 mm thick plastic laminated sheet top cover (ISI Marked) for mounting modular type switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLS PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly, for one light point /bell point/ ceiling fan/exhaust fan point controlled by one way switch complete all as specified and directed. (NOTES: - (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage) (a) One light point or one fan point controlled by one switch

All as per item No 101 but one 3/5 pin socket outlet, 5 Amp independent

All as per item No 101 but one 3/5 pin socket outlet, 5 Amp on the same board with other switches

All as per item 101 above but using 2.50 Sq. mm (nominal area) FRLS PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core for line conductor and 1.50 Sq. mm (nominal area) FRLS PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core for earth continuity wire for one 15/16 amp multi socket out let independent. (concealed wiring) (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches

All as per item No 101 above but using 4.0 sqmm single core multi stranded copper conductor PVC insulated and unsheathed, flame retardant Low Smoke (FRLSH ) cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and including 4.0 sqmm green solid copper conductor as continuous earth wire with lugs complete all as specified and directed.

S & F Modular Switch 1 way 6 A, 1 module complete all as specified and directed.

S & F Modular Switch 1 way 16 A, 1 module complete all as specified and directed.

S & F Modular Socket 6 A, 2/3 pin combined 2 module complete all as specified and directed.

S & F Modular Socket 6 A/ 16 A, 2/3 pin combined 2 module complete all as specified and directed.

S & F Modular Bell push 6A, 1 module complete all as specified and directed.

S & F Modular type White cover plate with frame 3 module complete all as specified and directed.

S & F Modular type White cover plate with frame 4 module complete all as specified and directed.

S & F Modular type White cover plate with frame 6 module complete all as specified and directed.

S & F Modular type White cover plate with frame 8 module complete all as specified and directed.

S & F Modular type White cover plate with frame 12 module complete all as specified and directed.

S & F Modular type Metal Flush box 3 module complete all as specified and directed.

S & F Modular type Metal Flush box 4 module complete all as specified and directed.

S & F Modular type Metal Flush box 6 module complete all as specified and directed.

S & F Modular type Metal Flush box 8 module complete all as specified and directed.

S & F Modular type Metal Flush box 12 module complete all as specified and directed.

S & F Ceiling rose, 3 terminal PVC insulated body complete all as specified and directed.

Cutting Chases pinning in, for concealed conduit wiring and making goods of disturbed surface not exc 15 cm girth complete all as specified and directed.

S & F Modular Fan regulator 120 W 2 module complete all as specified and directed.

Supply & fixing Bell AC 230 Volt single pole complete all as specified and directed .

Supply and fixing LED lights fitting 1 x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in repairs recess mounting LED 12 Watt slim round down lighter made of green Perform sleek is a high performance low-height LED modern professional workspace robust PDC housing ensures long system complete all as specified and directed . Make: Philips Cat-DN295B LED10S-6500 PSU WH or equivalent make specified in tender.

Taking down of old Submain wiring upto 10 sqmm any type including batten/ conduit/ casing at any indicated situation.

M & L for sub main wiring with 4 run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 10.0 sqmm alongwith one run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 10.0 sqmm as earth continuity conductor drawn through and including PVC casing-capping of suitable size, surface type all as directed.

All as per Srl. Item No. 128 above but with 2 run of 6.0 Sqmm cable and 6.0 Sqmm as earth continuity conductor.

All as per Srl. Item No. 128 above but with 2 run of 4.0 Sqmm cable and 4.0 Sqmm as earth continuity conductor.

S & F TP&N Vertical Loadline Dbs are fitted with Bus Bars, Neutral Links, Blanking Plates 4 way double door DB LL 4W DD VERT W/O MCCB complete all as specified and as directed

S&F in repairs of MCCB 4 Pole, 415 V, 100 Amps with adjustable type, breaking capacity 16 KA, Ics=100% of Icu with all accessories incl taking down existing MCCB complete all as specified and directed

S & F Double door sheet metal enclosure for DBs(Premium range) for mounting of MCB for 240 Volts 4 Way with 200 Amps rated copper bus bar, single pole and Neutral complete all as specified and directed.

Supply and fixing MCB, 'C' series, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed.

S & F Double door sheet metal enclosure for DBs(Premium range) for mounting of MCB for 240 Volts 8 Way with 200 Amps rated copper bus bar, single pole and Neutral complete all as specified and directed.

Supply and fixing MCB, 'C' series, single pole, 40 to 63 Amps, breaking capacity 10KA complete all as specified and directed.

S & F exhaust fan 300 mm sweep, AC single Phase 230 / 240 volts, metal body with louver shutters and connecting up with and including twin core twisted flexible copper conductor cable of suitable dia ,nut bolt and accessories, and winding, pending etc connecting up including taking down with re -fixing provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 sqmm , 3 core, 1100 Volts grade, from ceiling rose / connector to fan complete all as specified and directed.

S & F BLDC ceiling fans of 1200mm sweep with class F copper insulation for winding ,canopy, fan blades and accessories, BEE 5 Star Rated and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 sqmm , 3 core, 1100 Volts grade, from ceiling rose / connector to fan complete all as specified and directed.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

GHOSH ENTERPRISE (BID ID -3405168)

DEYS ENTERPRISE (BID ID -3410015)

ARJUN DAS VALECHA (BID ID -3411287)

UNIVERSAL TRADING CENTRE (BID ID -3406241)

JOY RAM ENTERPRISE (BID ID -3407535)

PRABIR TRADERS (BID ID -3406293)

GOODWILL AND CO. (BID ID -3408735)