Development of Unauthorised Colonies in NCT of Delhi.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Excavation of silt including malba, earth debries, rubbish ploythene bed all floating material etc. from the bed of drain and disposal of excavated material at own source of contractor by mechanical transport upto lead of 5.00 Km and lift upto 1.5 m complete as per directions of engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/ Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of M10 grade with minimum cement content of 220 kg /cum

Centering and shuttering including strutting, propping etc. and removal of form for Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like

Providing and laying RMC of M-30 grade by using minimum 400 Kg. of cement (43 grade OPC) per cum of concrete in roads/ streets manufactured in automatic RMC plant using coarse sand and graded stone aggregate of 20mm nominal size in appropriate proportion as per approved design criteria including transportation to site in transit mixer, including cost of admixture in recommended proportion as per IS 9103 to accelerate/ regard setting of concrete to improve workability wit out impairing strength and durability as per specification including spreading and compacting mechanically by using needle and surface vibrators , leveling to required slope and camber, finishing by floating and brooming with wire brushes etc. and curing including making provision for contraction/expansion, construction of cross/ longitudinal joints of size 10mm wide 50mm deep by groove cutting machine, providing and filling joints with approved joints filler and sealants, etc. complete as per direction of Engineer-in-charge( Cost of joint filler & sealants shall be paid for separately under relevant item). Note: Cement content considered in M-30 is @ 400 Kg/cum. Excess/Less cement used as per design mix is payale/recoverable separately M-30 RMC using minimum cement @ 400 Kg/cum. Cement concrete manufactured in automatic batching plant(RMC plant) including transportation to site in transit mixer.

Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge.

Raising of existing Manhole up to 60 cm (Av) height by dismantling of CC/RCC Cover and frame including brick masonry with bricks of class designastion 75 in cement mortar 1:4 (1cement: 4 coarse sand) with a floating coat of neat cement punning 12mm thick including cost of quantities to be executed in or under foul position complete as per direction of Engineer-in-charge.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality EHD - 35 Circular shape 560 mm internal dia

Supply of building Rubbish/Malba/similar unserviceable material dismantled or waste material by mechanical transport including royalty loading un-loading banking the same in layers not exceeding 20cm in depth, braking clods watering rolling each layer with 1/2 tonne roller or wooden or steel rammers and up to embankments for roads, flood banks, marginal banks and fluid or filling up ground depression, with all leads & all lifts.

Supply of earth including excavation, banking excavated earth in layers not exceeding 20 cm in depth, breaking clods watering, rolling each layer with 1/2 tonne roller, or wooden or steel rammers and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions by mechanical transport within 10 km. lead and lift upto 1.5m including royalty.

Providing and fixing 30 mm thick (undressed) red sand stone slab over drains.

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to plinth level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Supply of screen soil C&D waste product by mechanical transport including loading, unloading, royalty and banking the same in layers not exceeding 20 cm in depth, watering, rolling each layer with 1/2 tonne roller, or wooden or steel rammers and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions with mechanical lead upto 15 Km and lift up to 1.5m in all kinds of soil.

Providing and placing in position 150 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 150 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Hire charges for 10 HP Pump including fuel for running/maintenance, suction pipe up to 12m, delivery pipe upto 30m, Mobil oil, labouir for pump operation including pump operator for a period to 8 Hour as per directoin of Engineer-in-charge.

Please Enable Macros to View BoQ information