Development of BMT Bone Marrow Transmission Unit at 4th Floor Connecting Corridor between A and B block at AIIMS Patna

CONCRETE WORK Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : "1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

CONCRETE WORK Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size).

REINFORCED CEMENT CONCRETE Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for: Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

HALF BRICK MASONRY Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin- charge Extruded section profile size 48x40 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Approved Make - Godrej

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge.

Flooring Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110mm, diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110 mm

Single tee with door 110x110x110 mm

Bend 87.5° 110 mm bend

FINISHING Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

SANITARY INSTALLATIONS Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.(make- parryware/hindware)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar (make- hindware/perryware)

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32mm dia

WATER SUPPLY Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :(make- parryware/hindware) 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Cutting holes up to 30x30 cm in walls including making good the same With common burnt clay F.P.S. (non modular) bricks

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 40 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Aluminium Work Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed hanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron )

Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. 4mm thick aluminium composite panel material board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-incharge Powder coated minimum thickness 50 micron aluminium

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.Upto 5mm depth and 5 mm width

providing and fixing of PVC flooring of 4.5 mm thick, laid on semi conductive adhesive base and self levelling compound complete in all respect as per specification and as per direction of Engineer-in-charge.

Providing and fixing MW AL Tegular 8 micron Plain/Perforated Beveled Edge Global white color tiles of size 600x600 mm and 0.7mm thick module which includes providing and fixing 'C' wall angle of size20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with MW AL Tegular 8 micro Perforated/Plain Beveled Edge Globa white color tiles size of 600x600mm and.7mm thick with 25mm height,made of GI sheet having galvanizing of 100gms/sqm(both side inclusive) and elcto statically Polyster poder coated of thickness 60 microns(minimum) ,including factory painted after bending

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

The hermetically selead doors having size 2.1m x 1.8m with single sleading. The cantroler should be capable of being operted by elbow switch / foot switch as well as touch less sensor, the track should be of stainless steel/ aluminium & the running the surface for the top roller should be sutabile angled to reduce resistence to movement. the door leaf should be hung by means of hard plastice rollers of high quality with double bearing at the top. the roller should be provided under the stainless steel / aluminium track to enable smooth and noiseless movement. Opening and clossing of the door should be micro processor controlled electornically movement. Door material should be of HPL (High Pressure liminated board) , colour should match the interior and care should taken to make the leaf strong and light. the door should be able to open and close the door effortlessly in case of failure of automatic macanism. The door opening handle should be strong and material should be strong and well finiushed of material SS ( Glass funished) should be provided with high quality cylindrical lock. The door leaf should be high quality synthtic ruber gasket with long life to insure hermatic sealing (to maintain air puressure differential). the air tightness 99.99% at a pressure of 100 Pa the finushed door on either side of the door should be perfectlly level ( maxumam permissible differnce + 1mm). The overall thichness of the finushed door should be 55mm to 60 mm. The inner part of the door should be filled with CFC free polyurethane foam thickness of 48mm or nearby. ( sealed airtight to prevent further ingress of any microbial organism). The door and controll should be comply IEE regulations. All motors should be DC burshless motor with essential isolicaion from mains. The door should be with visble window pen of size 300mmx 300mm with double glassed panels and hermetically selead. Door movement should have minimum nosie. The starting time after receiving the signale should be adjustable between 0.5 to 20sec. Door controller should be CE marked, test certificate for hermetically selead door frame ( factory test certificate should be enclosed with the pre dispatch documents.

WOOD AND P.V.C. WORK Providing and fixing 19mm thick plywood (make - green ply, centuary, national) conforming to IS: 14587:1998 marked,with decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality (make - green lamp, centuary, decor) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately). 19 mm thick

Providing and fixing 19mm thick plywood (make - green ply, centuary, national) conforming to IS: 14587:1998 marked for door pannel and top cover,with decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality (make - green lamp, centuary, decor) in door pannel and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand including nickel plated bright finishing ss hinge (make - godrej, o degree) with necessary screw etc. all complete.

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 40 mm

Providing and fixing chromium plated brass handles with necessary screws etc. complete: 100mm

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. Triple strip vertical type

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 19mm thick plywood cabinet with necessary solution, mixed with matching pigment, epoxy touch ups, including rubbing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 sqm

misllenious civil work

ELECTRICAL Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface I recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable and 1.5 sq. mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. Group B

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3x4 sq. mm

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 180 mm X 100 mm X 60 mm

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 200 mm X 125 mm X 60 mm

Supplying and fixing following modular switch/ socket on the existing modular plate 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate 15/16 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate 10/6 A modular socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate 6 pin 15/16 A socket outlet

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, Gl box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm)

Supplying and fixing following size/ modules, Gl box alongwith modular base & cover plate for modular switches in recess etc. as required. 6 Module (125mmX125mm)

Supplying and fixing following size/ modules, Gl box alongwith modular base & cover plate for modular switches in recess etc. as required. 8 Module (200mmX75mm)

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connection etc. as required.

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFLILED lamps per fitting, complete with all accessories including connections etc. as required.

Dismantling of ceiling fan and painting the same with with one or more coats of spray painting with synthetic enamel paint of approved brand and manufacture to give an even shade, including cleaning of surface with detergent and replacing the damaged rubber reel, nuts and bolts with washers and safety pins reinstalling the same as required.

Supplying 15 Watt Led Light (Round 170 mm)

Supplying 18 Watt LED Light

Supplying 36 Watt Down Light (600x600 mm) (Make- Havells/Syska/Crompton/Philips)

25mm Casing &Caping

VRV works Supply, installation testing & commissioning of variable refrigerant volume or variable Refrigerant flow type Multi unit Air conditioning system complete with indoor & outdoor units with individual corded controller as per the following capacities of the AHU, Plenum & ODU. Modular type outdoor units equipped with highly efficient rotary compressor with all inverter type compressor(s) only, special acryl precoated heat exchanger. Low noise condenser fan, Condenser coil 4 face blue fin type exchangers. All refnet piping system shall be imported. Refrigerant should be 410A. All structural frame work platforms required shall be of HVAC vendor as per site condition. The ratio of indoor cooling capacity to outdoor cooling capacity in (KW) i.e. diversity should not exceed 120%. Outdoor and indoor units shall be integrated with special super wiring system with a central monitoring remote. VRF OUT DOOR UNIT VRF Full Inverter ODU 32 HP (16X2) Hp.

Supply, installation testing & commissioning of factory fabricated Double skinned Air handling unit fabricated out of extruded aluminium section with 0.6mm pre-plasticized/pre-coated Aluminium sheet outside (22G) & 0.6 mm polished ss sheet inside with backward curved fan in supply and forward curved in exhaust with fan section and fan motor TEFC type suitable for operation on 415 volts + 10% , 50Hz +5% AC supply, pre-filter section with Non-woven synthetic media of 10 micron particle size with an efficiency of 90% in both the supply & exhaust side of AHU, fine filter section with filter of non-woven synthetic media of 5 micron particle size in supply & exhaust after fan,(Hepa filters shall be at terminals along with laminar flow plenum, Heat recovery wheel with HRW section ,mixing chamber, polished stainless steel drain pan made out of 22G sheet duly insulated complete with motor, belt drive package guard etc. without face & bypass dampers. The AHU panels shall be insulated with 48mm thick & 36 kg/m3 density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on aluminium extruded section only. These AHUs shall have air inlet/outlet connection made of aluminium 20G & all fixing arrangement/ blank off shall be of SS. The complete AHU shall conform to standard speciation. The face velocity across cooling/heating coil shall be limited to 152 MPM maxim. The capacity of Air handler unit shall be as follow. For BMT Unit room 10000 CFM (25 TR) with odour control.

Laminar Air flow plenum for 2.1 Supply, installation testing & commissioning of factory fabricated Laminar air flow pattern perforated plenum made of 16 G aluminium sheet, Aluminium VAV box with controlling with separate thermostat , DOP tested Hepa filters of efficiency 99.97%down to 0.3 micron particle size & suitable for BMT unit with all accessories as required & to suite site condition of size 2.4x2.7m2 .

Supply, installation testing & commissioning of inline fan with connecting Aluminium duct toilet to outer side of the wall. The inline fan shall be dynamically balanced and designed for silent operation. The inline fan shall be suitable for operation on 220+6% Volts, 50HZ, and single phase Ac power supply capacities. The capacity of Inline fan unit shall be as follow. For BMT Toilet room 500 CFM Inline fan.

Simple central controller unit capable of controlling all the indoor & outdoor units.

Supply Air diffuser

Return Air diffuser

ANCILARY WORKS. Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : (Piping & accessories -Make-Maxflow/ Mandev /Rajco/diamond/star/Total lite /Met tube /Campiro) (Insulation; - Make (Keflex/vedo flex/Arma flex /Supreme /Aflex /Paramount) 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

25.4 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

Supply, installation testing & commissioning of 22G Aluminium duct from AHU to Laminar air flow & connecting corridor. Supply & return air flow from 22G Aluminium duct system complete with fitting, support from celling & 15mm thick Aluminium foil insulation as per site condition. 22G Aluminium sheet-Make-Hidalgo, Jindal. Insulation; - Make (Keflex/vedo flex/Arma flex /Supreme /Aflex /Paramount

SITC of electrical panel (panel to be designed by successful bidder with minimum rating of switchgears) Main incomer MCCB 100A

Outdoor VRV & AHU MCCB 32 A with enclosure

Supply ,installation, termination of cable as per specification ( for Communication IDU & ODU) (make – Polycab , finolex , havelles , Anchor, Gloster /CCI /National ) 4CX70 Sqmm copper Armoud cable

Supply ,installation, termination of cable as per specification ( for Communication IDU & ODU) (make – Polycab , finolex , havelles , Anchor, Gloster /CCI /National ) 4cX16 Sqmm copper Armoud cable

Supply ,installation, termination of cable as per specification ( for Communication IDU & ODU) (make – Polycab , finolex , havelles , Anchor, Gloster /CCI /National ) 4cX 6 sqmm copper Armoud cable

Earthling with copper earth plate 600 mm X3 mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.6 meter long etc. as required connection to equipment as per site condition.

Supply, Installation of perforated GI tray made out of 2mm thick sheet, suspended from celling &fixing on wall/Colum etc. Including GI hanger & supports fastener etc. as required cable tray layouts with supporting arrangements. 150 mm (W) x 40 mm (D)

Comprehensive Annual maintenance contract of 32 HP The system will be checked for its proper functioning any defects if found to be rectified within the stipulated period/time. All defective spares shall be repaired/replaced as and when required during the contract. Any consumable like oil, refrigerant also to be supplied whenever necessary indoor units filter to be supplied whenever necessary indoor units to be inspected and cleaned as per the schedule. All number of breakdown call pertains to the refrigeration equipment irrespective of the nature of call to be attended under this contract. 1st year after warranty period

Comprehensive Annual maintenance contract of 32 HP The system will be checked for its proper functioning any defects if found to be rectified within the stipulated period/time. All defective spares shall be repaired/replaced as and when required during the contract. Any consumable like oil, refrigerant also to be supplied whenever necessary indoor units filter to be supplied whenever necessary indoor units to be inspected and cleaned as per the schedule. All number of breakdown call pertains to the refrigeration equipment irrespective of the nature of call to be attended under this contract. 2nd year after warranty period

Comprehensive Annual maintenance contract of 32 HP The system will be checked for its proper functioning any defects if found to be rectified within the stipulated period/time. All defective spares shall be repaired/replaced as and when required during the contract. Any consumable like oil, refrigerant also to be supplied whenever necessary indoor units filter to be supplied whenever necessary indoor units to be inspected and cleaned as per the schedule. All number of breakdown call pertains to the refrigeration equipment irrespective of the nature of call to be attended under this contract. 3rd year after warranty period

Comprehensive Annual maintenance contract of 32 HP The system will be checked for its proper functioning any defects if found to be rectified within the stipulated period/time. All defective spares shall be repaired/replaced as and when required during the contract. Any consumable like oil, refrigerant also to be supplied whenever necessary indoor units filter to be supplied whenever necessary indoor units to be inspected and cleaned as per the schedule. All number of breakdown call pertains to the refrigeration equipment irrespective of the nature of call to be attended under this contract. 4th year after warranty period

Comprehensive Annual maintenance contract of 32 HP The system will be checked for its proper functioning any defects if found to be rectified within the stipulated period/time. All defective spares shall be repaired/replaced as and when required during the contract. Any consumable like oil, refrigerant also to be supplied whenever necessary indoor units filter to be supplied whenever necessary indoor units to be inspected and cleaned as per the schedule. All number of breakdown call pertains to the refrigeration equipment irrespective of the nature of call to be attended under this contract. 5th year after warranty period

SMPL INFRA (INDIA) PVT LTD