SPL REPAIR TO OFFICER MD ACCN BUILDING NO P 2 P 5 AND P 8 AT USMAN VIHAR AND P 2 AND P 7 AT CNS VIHAR UNDER GE SOUTH AKHNOOR

Amount

Demolition of cement concrete (unreinforced) concrete in ground floors and paving n.exc 15cm thickness (below or above ground floors), complete all as specified and directed.

M&L cement concrete type B0 1:2:4 using 12.50mm graded stone aggregate 25mm thick as in flooring levelling course etc., complete all as specified and directed.

M&L screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement 1:6, complete all as specified and directed.

S&F Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed.

All as per Srl Item No. 4 but in skirting alongwith 10mm thick in CM 1:4 as backing plaster, complete all as specified and directed.

S&F Vetrified Ceramic tiles 10 mm thick Light Shade (square/ rectangular) polished, area of each tile not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match , complete all as specified and directed.

S&F Vetrified Ceramic tiles 10 mm thick Light Shade (square/ rectangular) polished, area of each tile not exceeding 0.36 Sqm, on vertical surface such as skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match , complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection 750 mm wide joint filled with bitumen sand mixer finished even and smooth without using extra cement, complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Rendering 10mm thick on fair faces of brick work or concrete surface in cm 1:4 as for tiles screed bed, complete all as specified and directed.

M&L glazed ceramic coloured designer pattern tiles350X250X7MM / 450mm x 350mm x 7mm thick on vertical surface such as skirting, Dado etc. set and jointed in white colour cement, complete all as specified and directed.

RCC 1:2:4 type B1 slabs for kitchen shelves etc using 20mm graded stone aggregate, complete and including formwork all as specified and directed.

M&L for granite 20mm thick (table rubbed and polished) in cooking platform and like in cement mortar 1:4 including pointing in white cement(1:2) using marble dust making holes in RCC shelves suitable for gas pipe with round edges where required, complete all as specified and as directed .

Demolition for cement conc exc 15cm thickness but above ground floor as sunken floor, complete all as specified and as directed.

M&L for 15mm thick rendering in 1:3 CM with using 3% WPC as in sunken portion complete all as directed. (WPC measured and paid separately).

M&L for applying evenly a tack coat of industrial bituminous 85/25 @ 1.20 Kg per square mtr including cleaning surfaces, complete all as specified and as directed.

M&L cement concrete type B0 1:2:4 using 12.50mm graded stone aggregate 25mm thick as in flooring for sunken portion with using 3% WPC etc. ,complete all as specified and as directed.

M&L PCC 1:5:10 type E-2 using 40mm graded stone aggregates as filling under (sunken slab) floors, complete all as specified and as directed.

M&L for 40mm thick Plain Cement concrete type B0 1:2:4 using 12.50mm graded stone aggregate as in floor etc complete mixed with WPC @ 3% by weight of cement (WPC measured and paid separately) laid finished even and rough to receive plaster without using extra cement complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregates as sides of rounded or chamfered on edges of sunken floor complete all as specified and directed.

Cutting holes into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required area not exc. 150cm, complete all as specified and as directed.

S&F 32mm dia GI pipe beveled cut at both ends by making hole in walls sunken portion approx above the RCC slab and ceiling, finished the hole with cement plaster 1:2 to match with existing surfaces complete etc., complete all as specified and as directed.

M&L grubbing up bushes, tree truck of trunk portion nexc 30cm girth including cutting of trees/bushes grown in over wall and roofs digging out roofs and making good distance area of wall/roofs with PCC 1:3:6 type and using 20mm graded stone aggregate, complete all as specified and as directed.

M&L for repairing RCC projection chajjas, roof, facia etc. by necessary preparation, scraping, cutting, chiseling derusting and cleaning exposed reinforcement surfaces of damaged, loose RCC surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregates and reinforcement with welded mesh of weight exc 2Kg per Sqm but n.exc 3Kg/Sqm (if required) with or without facia and finished with cement mortar 1:3 using coarse sand and work in patches area n.exc 5 Sqm and thickness RCC member n.exc 70mm incl necessary formwork and applying two coats of finishes to match with the existing surfaces at any height, complete all as specified and as directed. (Note: welded mesh to be paid separately)

S&F Expanded metal,weight not exceeding 4.0 Kg per Sqm,cut to length,bent to shape required and tying with and including annealed mild steel wire not less than 0.90mm dia or fixing with galvanised steel staples/screws supplied and fixed complete to concrete to concrete or steel member,complete all as specified and as directed by Engineer-In-Charge.

Dismantling brick tiles or terracing tiles on roofs, complete all as directed by the Engr-in -charge.

Removal of APP membrane of any description including roughing of old concrete surface with wire brushes and cleaning ,washing with water to remove all loose dust etc including removal of material i.e. debris exc 50m but not exc 100mtr from the site complete all as directed by the Engr-in -charge.

Applying cement slurry @ 3-00 Kg/Sqm cleaned roof surface, complete all as specified and directed.

M&L for 10mm thick screed bed in CM 1:4 mixed with water proofing compound @ 3% by weight of cement in order to maintain proper slope over existing roof surface for laying of APP based polymeric membrane finished even and smooth without using extra cement, complete all as specified and directed. (Note: Water proofing compound shall be measured and paid separately).

M&L Water proof treatment on roof top with APP (Ataxic Poly Propylene) modified polymeric five layered membrane with central core of 100 micron high molecular high density polyethylene film, minimum weight not less than 3.0 Kg/ Per Square Metre, 2.0mm thick, centre core is sandwiched on both sides by high quality polymeric mix with properties of high softening point, high heat resistance and cold resistivity to make it ideal for all water proofing treatment, with polymeric mix protection on both sides with 20 micron HMHDPE film, laid over one coat of bituminous primer conforming to IS: 3384, applied @ 0.40 Kg/ Per Square Metre and one coat of hot blown bitumen of 85/25 grade, conforming to IS:702, applied @ 1.20Kg/ Per Square Metre on prepared surfaces of roof, overlap should be not less than 150mm at ends and 75mm at sides, joints and overlaps uniformly bounded with LPG torch flame including applying of one coat of semi hot blown bitumen of 85/25 grade, @ 1.20 Kg Per Square Metre and fine screened sand in dry condition @ 0.50 Kg/ Per Square Metre after laying the membrane, complete all as specified and as directed by Engineer-In-Charge.

M&L for Providing 20cm x 20 cm x 20mm thick precast PCC tiles jointed & pointed flush in CM 1:6 over 15mm thick bedding layer of CM (1:6) using white cement & pigment , complete all as specified and as directed.

Taking down or up steel tubing and connections including cleaning for re-fixing or removal to store 15mm bore, complete all as specified and directed.

Taking down or up steel tubing and connection s including cleaning for re-fixing or removal to store 20mm bore, complete all as specified and directed.

S&F for Tube 'medium grade' galvanized, with all fitting and fixed complete to walls and ceiling etc 15mm bore, complete all as specified and directed.

All as per item No 34 but 20mm bore, complete all as specified and directed.

Cutting chases in bk wall for concealed water tubing exc 10 cm but not exc 20 cm girth and making good.

S&F Bib taps chromium plated fancy type, ( minimum weight not less than 0.575 Kg) cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repair 15mm bore, complete all as specified and directed.

S&F for wall mixer with provision of shower for mixing hot and cold water 3 in 1 fancy type brass chromium plated (minimum weight not less than 1.75 Kg) with long shank and cup screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed 15mm bore fixed, complete all as specified and directed.

S&F for stop cock fancy type chromium plated ( minimum weight not less than 0.575 Kg) with cast copper alloy screwed down high pressure with or without lathered hot and cold with long screwed shanks and fly nuts fixed in repair 15mm bore, complete all as specified and directed.

S&F for wall mixer as in sink mixer 2 in 1 , cast copper alloy, with chromium plated ( minimum weight not less than 1.75 Kg) screwed down high pressure with or without lathered hot or cold with long screwed shanks and fly nuts screwed for iron pipe 15mm bore, complete all as specified and directed.

Supply and fixing as in repairs vitreous China squatting pattern Orissa pattern WC size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but excluding lime concrete bedding complete all as specified and as directed.

S&F for PVC connection 15mm bore size with PTMT nuts of length 60cm, complete all as specified and directed.

S&F Full pedestal vitreous china wash basin wall hung Basin with fixing accessories set, white flat back size 560 x 430 x 195mm excluding taps, all as specified and directed. Make :Jaquar / Marc/ Cera.

S&F 15mm angular stop cock with wall flange stainless steel/Brass chromium plated (minimum weight not less than 0.575 Kg),screwed down high pressure with or without lathered hot and cold with long screwed shanks and fly nuts complete all as specified and directed.

S&F as in repairs PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle including brackets. 10 ltr capacity, complete all as specified and directed.

S&F for fancy brass chromium plated shower rose 125mm fixed in repair, complete all as specified and directed.

Ball valve high pressure of PTMT with epoxy coated Aluminum rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed in repair 20mm bore, complete all as specified and directed.

S&F for stainless steel with draining board made of 1.00mm thick sheet for kitchen with plug , washer waste pipe cast iron cantilever bracket connecting union overall size 915mmx 460mm with bowl size 330mm x160mm., complete all as specified and directed.

S&F CP grating 150mm dia with centre hole, complete all as specified and directed.

(a) Supply and fixing Modular Kitchen System suitable for Captain's accomodation having upper cabinets and lower cabinets which includes all utility accessories such as cutlery organisers, cutlery organiseser trolys, pull out baskets, bottles pull outs, tall units, corner units, under sink assessories etc complete. (b) Upper cabinet system shall have minuimum 4.00 sqm area with Aluminum Composite Panel (ACP) with Aluminium sections 40mm x 40mm,window sections 60mm x 32mm, Aluminum tube 25mm x 40mm , 5mm thick designer glass, 8mm thick glass shelves, aluminum angles 25mm x 25 mm, rubber 4mm, aluminum beading clips, stainless steel handles and hinges, catches steel magnetic type etc complete (c) Lower cabinet system shall have minimum 5.60sqm area with aluminum composite panel (ACP) sheet 4mm thick with aluminum section 40mm x 40mm, window sections 60mm x 32mm, hydraulic channel 500mm by 25 mm. 5mm thick designer glass , 8mm thick glass shelves, aluminum angels 25mm x 25mm , rubber 04mm , aluminum bidding clips, catches hinges etc complete (d) Colour of ACP sheet , make and design and layout of modular kitchen will be approved by GE. (e) ACP sheet make : Viva, Euroboard, Alstone, Alucobond, Alstrong

(a) Supply and fixing Modular Kitchen System suitable for Major's accomodation having upper cabinets and lower cabinets which includes all utility accessories such as cutlery organisers, cutlery organiseser trolys, pull out baskets, bottles pull outs, tall units, corner units, under sink assessories etc complete. (b) Upper cabinet system shall have minuimum 5.60 sqm area with Aluminum Composite Panel (ACP) with Aluminium sections 40mm x 40mm,window sections 60mm x 32mm, Aluminum tube 25mm x 40mm , 5mm thick designer glass, 8mm thick glass shelves, aluminum angles 25mm x 25 mm, rubber 4mm, aluminum beading clips, stainless steel handles and hinges, catches steel magnetic type etc complete (c) Lower cabinet system shall have minimum 8.60sqm area with aluminum composite panel (ACP) sheet 4mm thick with aluminum section 40mm x 40mm, window sections 60mm x 32mm, hydraulic channel 500mm by 25 mm. 5mm thick designer glass , 8mm thick glass shelves, aluminum angels 25mm x 25mm , rubber 04mm , aluminum bidding clips, catches hinges etc complete (d) Colour of ACP sheet , make and design and layout of modular kitchen will be approved by GE. (e) ACP sheet make : Viva, Euroboard, Alstone, Alucobond, Alstrong

S&F in repair Rotational moulded polythene water storage tanks(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 1000 ltr capacity , complete all as specified and directed.

S&F Rotational moulded polythene water storage tanks(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 500 ltr capacity incl dismantling water tanks and removing to store, complete all as specified and directed.

S&F for Gun-metal, globe or gate valves, for bore dia of pipe in 15 mm with iron wheel head, screwed both ends for iron pipe and fixed in repairs, complete all as specified and as directed.

Vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts, flush pipe but excluding flushing cistern) and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and making good to dismantled/ damaged floor in cement concrete M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregates), fixing in repair, all as specified.

S&F brass chromium plated tubular towel rail 20mm dia(D) type 60cm long between flanges complete.

S&F 32mm dia waste pipe for WHB, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, complete all as specified and directed.

Taking down chokats or frames with shutters (without taking off shutters from frames) exceeding 1.5 Sqm but n.exc 4 Sqm each , complete all as specified and directed.

Pressed steel frames for doors with one or more rebates 1.25 mm thick profile including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 125x60mm, complete all as specified and as directed .

Pressed steel frames for doors with one or more rebates 1.25 mm thick profile including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 105x60mm, complete all as specified and as directed.

Plain cement concrete M-10(1:3:6), type C-0, (using 12.50mm graded crushed stone aggregate), nominal mix, as in cills, steps; plinth courses, string courses, lacing courses, copings, kneelers, apex stones, bed plates and in hold fasts or filling in hollow of steel frame, including necessary form work, complete all as specified and as directed.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rein forced with M.S. square tube supplying and fixing in opening as per specification and drawing.

S&F Powder coating of any colour (Thickness or powder coating not less than 50 micron). Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long suitable handle (2 no.) complete all as specified. Note :- (Contractor shall submit certificate for anodised coating and powder coating before claiming any payment )

S&F Aluminium anodised window grill with 8mm dia ornamental type bars of design and pattern all as approved by the GE,complete all as specified and as directed. Note :- (Contractor shall submit certificate for anodised coating and powder coating before claiming any payment )

S&F Supply only aluminium alloy wire cloth of nominal dia of 0.45mm and average width of aperature 1.40mm and fixed with aluminium wire staples complete all as specified and directed . Note :- (Contractor shall submit certificate for anodised coating and powder coating before claiming any payment )

S&F Powder Coating (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors/ windows/ ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified. Note :- (Contractor shall submit certificate for anodised coating and powder coating before claiming any payment )

S&F sheet glass ordinary quality and glazing with oil putty in square nexc 0.5 Sqm Each pane 5.5 mm thick, complete all as specified and directed.

Figured glass pin head type glazed with oil putty in square n-exc 0.5 Sqm in Each pane 5mm thick, complete all as specified and directed. .

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded etc. with suitable PVC sheet beading including hinges etc., complete all as specified and directed.

Factory made, 40 mm thick flush shutters, solid core construction,with block board core and plywood face panels,commercial type both face is covered with decorative face veneer with lipping/frame to match. all as specified and directed.

Glazed and Skelton shutters using 2nd class hard wood 35mm thick open rebated and prepare to receive glass or gauge etc edges of framing plain and chamfered or fitted cut or mitered beads for securing glass size of member of shutter as specified in SSR Part-I section 8, clause 8.23(a) and divided in square, complete all as specified and directed.

S&F for glavanised Mild steel wire cloth. 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvnaised wire staples, complete all as specified and directed.

Supply and fixing of cupboard shutter 20mm thick (style) factory made pannel PVC incl chowkat frame made out of m.s tubes 19 gauge for top and bottom rails m.s frame shall be covered with heated moulded plain colour PVC channel having a PVC sheet strip of 10mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side 10mm (5mmx2) thick of 20mm and 20mm cross PVC sheet and as gap insert for top and bottom rail. Pannelling for plain colour PVC sheet to be fitted in the m.s frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying fixing in the frame at site as per specification and drawing as in repairs, complete all as specified and directed.

Preparation of new or previously untreated wood or wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying two coats of synthetic enamel paint over one coat of zinc chrome primer, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section and fixed, length of bolt 150mm, complete all as specified and directed.

S & F Aluminum alloy, anodized sliding door bolt with hasp staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolt of extruded section or cast aluminium alloy 250 mm long, complete all as specified and directed.

S&F extruded aluminum alloy handles 150mm size fabricated type anodized, complete all as specified and directed.

S&F Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg Aluminium(Die cast ) body and fixed

Floor doors stoppers of aluminium alloy body and tenque anodisede with hard drawn steel spring fixed in floor 150mm long, complete all as specified and directed.

S & F Butt hinges, medium weight cold rolled mild steel 100mm long Doors etc, complete all as specified and directed.

S&F epoxy powder coated pelmet rods of mild steel 25 mm with and including pair of fancy type finnals complete fixed as in repair, complete all as specified and directed.

Demolition of brick built in CM including all quoins arches pillars etc., complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved in plane exc 6cm mean radius built in cm 1:6, complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc., complete all as specified and directed.

M&L 10mm thick plastering on fair faces of bricks or concrete surfaces finished even and smooth w/o using extra cement in cm 1:6, complete all as specified and directed.

M&L 5mm thick plastering on fair faces for concrete surfaces finished even and smooth w/o using extra cement in cm 1:3 on ceiling , complete all as specified and directed.

M&L 15mm thick plastering on fair faces of bricks or cone surfaces finished even and smooth w/o using extra cement in cm1:4, mixed with water proofing compound @ 3% by weight of cement, complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid separately).

M&L Preparing of new plastered surface walls and applying three coats of white wash, complete all as specified and directed.

Preparation of new surface of wall with 3mm thick Birla putty on plastering surface and applying two coat of oil emulsion white or coloured over a coat of primer of chalkwihiting or priming of OBD on walls, complete all as specified and as directed.

Complete removal of existing treatment and applying two coats of Acrylic exterior paint of required shade as approved by GE over a coat of exterior primer Make: Berger,Asian,Nerolac Note : - Coverage area of paint and primer shall be strictly followed as per Manufacturer's instructions.

Preparation of new plastered surface of wall and applying two coats of Acrylic exterior paint of required shade as approved by GE over a coat of exterior primer Make: Berger,Asian,Nerolac Note : - Coverage area of paint and primer shall be strictly followed as per Manufacturer's instructions.

M&L for preparation of old surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including cornices, pilasters etc (plastered or unplastered surfaces) and applying one coat of white (lime) wash, complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new surfaces of ceiling and applying three coat of white wash on ceiling, complete all as specified and as directed by Engineer-in-Charge.

Dismantling of 100mm dia cast iron or reinforced concrete drain pipes, jointed in cement motar and taking out from floors or walls, complete all as specified and directed.

Dismantling of 75mm dia cast iron or reinforced concrete drain pipes, jointed in cement motar and taking out of trenches, if required, complete all as specified and directed.

S&F 100mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls, complete all as specified and directed.

S&F 100mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, in floors, complete all as specified and directed.

S&F 75mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors, complete all as specified and directed.

S&F 75mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls, complete all as specified and directed.

S&F bend (any radius) with ducks foot or heel rest of 100mm bore, complete all as specified and directed.

S&F bend (any radius) with ducks foot or heel rest of 75mm bore, complete all as specified and directed.

S&F branch pieces single (equal or unequal, ordinary or inverted with parallel branch of bore 100mm, complete all as specified and directed.

S&F branch pieces single (equal or unequal, ordinary or inverted with parallel branch of bore 75mm, complete all as specified and directed.

S&F Bends of 100mm diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F Bends of 75mm diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F branch pieces double (equal or unequal, ordinary or inverted with parallel branch of bore 100mm, complete all as specified and directed.

S&F 100mm dia CI P or S trap, complete all as specified and directed.

S&F 100mm CI floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

S&F 150 x 100 mm dia SW Gully trap setting and jointing with cement mortar 1:1, complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed stone ware, AC/PVC pipe n.exc 150 mm dia including all fittings, complete all as specified and directed.

PCC(1:3:6) type C-2(using 40 mm graded stone aggregate) as in bed to 150 mm dia internal pipe including packing under & haunching against the sides of pipes after they are laid tested complete all as specified & as directed.

Salt glazed stone ware drain pippes 150 mm internal dia grade 'A' laid in trenches , jointed & tested complete all as specified & as directed.

S&F for 110 mm PVC (SWR) Rain water pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

S & F PVC (SWR) bends 110 mm dia, complete all as specified and directed.

Demolition of Concrete (reinforced) of any description and in any position not otherwise specifically provided, complete all as specified and directed.

Pre-cast cement concrete 1:2:4 cover slab for manholes etc using 20mm graded stone aggregate set in cement 1:4, complete all as specified and directed.

TMT steel bars 10mm dia and over cut to length bent to shape reqd including cranking ,bending spirally for hooping for columns hooking bends and binding with including mild steel wire (annealed) not-less than 0.9mm dia or securing with clips quality, complete all as specified and directed.

Clearing of blocked SGSW/Cast Iron pipes/sewer lines of any dia and any types in horizontal or vertical position by rodding from WC to manholes, manholes to manholes, manholes to septic tank/soakage wells flushing with pressure jet of water after taking out existing manholes covers and putting back in original position after cleaning of lines including removal of sludge and other waste materials/blockage in drain pipe to outside unit area and spreading bleaching powder on top of septic tank/ soakage well/ manholes etc. to make hygienically fit, complete all as specified and directed.

Removing the existing cover slab from manhole of internal dimenions 1.20m(L) X 1.20M(B) and depth n.exc. 2.50m, taking out entire sludge/sludge water incl foreign materials from manhole and flushing with water till clear flow of water is observed, refixing the manhole cover, removing the sludge to a distance n.exc 50m and burring the entire sludge in excavated pit of suitable size and covering the pit with earth and bleaching powder @ 0.15kg per sqm of pit, spreading levelling the surplus earth along sides of the pit, complete all as specified and directed by Engr-in-Charge.

Supply only Integral water proofing compound, complete all as specified and directed.

Provn of MS work as in stand for desert cooler, AC, Ladder ornamental sections, rails fastining and heavy bracket framing ( beam, tee, angle, chennel or flat section etc confirming Fe 410 Gde 250.

M&L for 75mm thick PCC 1:4:8 type D-2( using 40mm graded stone aggregate ) as in sub base flooring including form work

M&L screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement 1:6, complete all as specified and directed.

Chequered cement concrete tiles glossy finish coloured 300mm x300mm x25 mm thick pattern as approved by GE as in patches in floor set & jointed in neat cement slurry and pointed in coloured cement to match the tiles laid over.

Taking down carefully aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pedants, regulators, sockets, light fitting etc., and making good the disturbed surfaces of walls/ floor etc matching with the existing surface, complete all as specified and directed.

Taking down U/s submain wiring aluminium etc. and making good the disturbed surfaces of walls/ floor etc matching with the existing surface, complete all as specified and directed.

Taking down U/S sheet metal enclosure concealed type with MCBs including making good the disturbed suface complete all as specified.

Taking down Exhaust fan, dismantling blades,deposite Exhaust Fan to MES store yard complete all as specified and directed.

Taking down C/Fan, Seailing cable end, dismantling blades and removing fan and blades and deposite to MES store complete all as specified.

Taking up/down old Under Ground cable of any size/type including complete all as specified and directed.

Disconnecting, removing carefully old Electric water heater of capacity 25/50 Ltrs including PVC Connection and handing over to AGE E/M store yard including making good the surface complete all as specified and directed.

Disconnecting, removing carefully the Temper proof electronic Energy meter and handing over in AGE E/M store yard all as specified and directed.

Taking down of old U/S GI bracket set fixed on wall including making good the suface complete all as specified and directed.

Material and labour for point wiring complete with 1.5 sqmm PVC insulated, FRLSH type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade (MMS) and including cutting, chasing work at any height and all accessories are in concealed in walls /roofs/floors / ceiling etc. flush mounting MS box with top,bottom,side/back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloures and including 1.5 Sqmm PVC insulated multistranded FRLSH type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for the following:- (Note:- All necessary accessories such as modular box,top cover, plate, blank plate,MS box,screws,washers and all modular electrical fixtures are to be used same make/brand only and shall be deemed in to included in quoted rate only.) (a) One light point/fan point/ exhaust fan point/ bell point controlled by one switch.

(b) One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board .

(c) One 5 pin 6 amps socket point controlled by one 6 amps switch on same board .

(d) One light point controlled by two 2 way switches.

Description all as per item No.137 above, but point wiring with 2.5 sqmm and earth conductor of size 2.5 sqmm complete all as specified and directed but for One 6 pin 20/10 amps socket outlet point controlled by one 16/20 amps switch on independent board complete all as specified and directed.

Supply & fixing modular type switch 10 Amps, single pole,1way,1 or 2 module, 240V, ISI Marked complete all as specified and directed.

Supply & fixing modular type switch 10 Amps, 2way, single pole,1 or 2 module, 240V, ISI Marked complete all as specified and directed.

Supply & fixing Modular Bell push 6 Amp 1 module complete all as specified and directed.

Supply & fixing modular type socket shuttered type 6 Amps, 2/3 Pin combined 2 module, 240V, AC ISI Marked Complete all as specified and directed.

Supply & fixing modular type socket 10A/20 Amps, 6 Pin combined shuttered socket 2/3 module with light indication ,240V,AC ISI Marked Complete all as specified and directed .

Supply & fixing modular type switch 16/20 Amps, single pole,1way,1 or 2 module, 240V, ISI Marked Complete all as specified and directed.

Supply & fix fan regulator modular type electronic, stepped type(01 to 4/5), 100 to 120 Watts, 240Volts, AC, ISI marked complete all as specified and directed.

Supply & fixing Bell, AC, 230 volts, single pole multi music type complete all as specified and directed.

Supply & fix ceiling rose, 3 terminal ,PVC/polycarbonate body ISI marked, complete all as specified and directed

Supply & fix angle lamp holder, polycarbonate insulated body with back plate for bulb complete all as specified and directed.

Supply and fix LED bulb 9 watts, 240Volts,50Hz pin type and including removing old unserviceable item complete all as specified and directed.

Supply and fixing Modular LED Indicator Lamp fixing on modular switch board 240V, AC, 50Hz suitable for 1/2 module ISI marked, including connecting with suitable length of 1.5sqmm PVC insulated copper conductor complete all as specified and directed. Make : Anchor Roma Cat No 21180R or equivallent Make in LEGRAND, PHILIPS, BAJAJ.

S&F Inverter based LED tube light fitting, 20 watt, 4 feet long indoor decorative high lumen batten 230 volts, AC 50 Hz, 6500K, polycarbonate channel with lithium battery with back up time up to 4 hours and connecting up with twin core twisted flexible copper cable complete Make : Havells cat No LHEXACP7FN1W020 or equivallent Make in LEGRAND, PHILIPS, BAJAJ.

S&F LED tube light fitting, 20 watt, 4 feet long indoor decorative high lumen batten, including connecting up with twin core twisted flexible copper conductor cable of suitable size, complete all as specified and directed. Make:- Havells Cat No LHEXACP7IN1J020 or equivallent Make in LEGRAND, PHILIPS, BAJAJ.

S&F LED tube light fitting, 10 watt, 2 feet long indoor decorative high lumen batten, polycarbonate housing, environmental friendly including connecting up with twin core twisted flexible copper conductor cable of suitable size, complete all as specified and directed. Make:- Havells Cat No LHEXACP7IN1W010 or equivallent Make in LEGRAND, PHILIPS, BAJAJ.

S&F Decorative wall light fixture Globe type including 9 W LED Lamp made up of polycarbonate complete all as specified and directed. Make- Havells Cat No-LHFOFUE1TZ1W012 or equivallent.

S & F LED Bulk Head fitting 1x13.5 watt and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed. Make: Havells Cat No LHEXCGP7IN5W013 or equivallent Make in LEGRAND, PHILIPS, BAJAJ.

Supply and fix LED secruity light fitting of capacity 45 Watt in aluminium PDC housing, toughened glass cover with IP66 protection with suitable inbuilt surge protector and cable connection from ceiling rose to light fitting and testing complete all as specified and directed. Make: Havells Cat No ENDURAPEARLNEOSL45WLED757PASYTOPC or equivallent Make in LEGRAND, PHILIPS, BAJAJ.

Supply and fix ceiling fan of size 1200 mm sweep with BLDC Motor,high speed, single phase, 240Volts,AC, 50Hz,as approved colour and including down rod of length of length 0.6M for hanging GI hook with necessary suitable MS clamps and connecting cable three core 0.75 sqmm round PVC sheathed from ceiling rose to fan connector and testing complete all as specified and directed.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete one single pole MCB 20/30 Amps, 240V complete concealed on wall and connecting with all connections all as directed by Engr- in -charge

Supply and fix heavy duty Exhaust fan 300 mm sweep metal body 900 RPM, 230 Volts, 50 Hz with louver shutter and connecting up including necessary alteration of the hole if necessary and making good the hole, provision of cable 3 core of 0 .5 sqmm from ceiling rose to fan complete all as specified and directed.

Supply and fixing Ventilating Fan Plastic body 250 mm sweep with louver shutter and connecting including provision of cable 3 core of 0 .5 sqmm from ceiling rose to fan all as directed.

Supply and fix wall mounted fan 400 mm sweep along with speed control complete with all accessories incl mounting on wall with necessary arrangemets complete all as specified and directed.

Supply and fixing or laying XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade cross-sectional area 70 sqmm 3.50 core from existing pole to bldg complete fixing arrangement all as directed by Engineer-in-Charge

Supply, fixing, connection, testing and commissioning of Storage Water Geyser of capacity 25 Ltrs, BEE 5 star rated, single phase, incuding suitable size of fatstener bolts, including connection complete all as specified and directed. MAKE: BAJAJ or equivallent Make in HAVELLS, RACOLD, SURYA.

Supply and fixing Vertical type sheet metal enclosure DB TPN 6 way double door made powder coated out of CRCA mild steel sheet 1.6 mm thick 415 volts 200 amps rated fitted bus bar dust and vermin proof suitable for incorporation of MCCB as incomer and MCBs as out going duly concealed on wall and making good the disturbed surface including MCCB, four pole, 125 Amps, 415 volts, 50 Hz,16KA complete all as specified and directed.

Supply and fixing Vertical load line sheet metal enclosure DB TPN 6 way double door made powder coated out of CRCA mild steel sheet 1.6 mm thick 415 volts 200 amps rated fitted bus bar dust and vermin proof suitable for incorporation of MCCB as incomer and MCBs as out going duly concealed on wall and making good to disturbed surface including MCCB, four pole, 160/163 Amps, 415 volts, 50 Hz,16KA complete all as specified and directed.

Supply and fixing sheet metal enclosure DB TPN 6 way double door made powder coated out of CRCA mild steel sheet 1.6 mm thick 415 volts 200 amps rated bus bar dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to disturbed surface complete all as specified and directed.

Supply and fixing in repair sheet metal enclosures DB's double door factory made power coated out ofr CRCA mild steel sheet 1.6 mm thick with metallic painting white series, 240 volts 200 amps rated enamelled bus bar 4 way dust and vermin proof proof suitable for incorporation of MCBs duly concealed in wass and making good to disturbed surface and colour matching complete all as specified

Supply & fix MCB TPN 40 Amps 10 KA,"C" series, AC, 415Volts, 50Hz, ISI marked complete all as specified and directed. Make :- Havells Cat No DHMGCTNF040 or equivallent Make in LEGRAND, PHILIPS, BAJAJ.

Supply & fix MCB TP 40 Amps 10 KA,"C" series, AC, 415Volts, 50Hz, ISI marked complete all as specified and directed. Make :- Havells Cat No DHMGCTPF040 or equivallent Make in LEGRAND, PHILIPS, BAJAJ.

Supply & fix MCB SPN 6- 32 Amps 10 KA,"C" series, AC, 240Volts, 50Hz, ISI marked complete all as specified and directed. Make :- Havells Cat No DHMGCSNF006-032 or equivallent Make in LEGRAND, PHILIPS, BAJAJ.

Supply & fix MCB SP 6 to 32 Amps 10 KA,"C" series, AC, 240Volts, 50Hz , ISI marked complete all as specified and directed. Make: Havells Cat No DHMGCSPF006-032 or equivallent Make in LEGRAND, PHILIPS, BAJAJ.

M & L for sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked)cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed,flexible,multi stranded colour coded cables drawn through and including rigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc concealed in wall/roofs/floors and including one run of 6 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLSH type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat and applying putty including cutting and chasing and complete all as specified and directed. Note : - Two run of 6 sqmm single core copper conductor cable and one run of 6 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit only.

Description all as per item ser No 175 here-in-before but 2 run of 4.0 single core and one run of 4.0 sqmm single core as earth wire for geyser complete all specified and directed.

Description all as per item ser No 175 here-in-before but 4 run of 10.0 single core and one run of 10.0 sqmm single core complete all specified and directed.

Material and labour for Earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directely in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipe of 15 mm dia from earth electrode up to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including charcoal, salt packed all around the earth electrode plate in layers, PCC earth pit chamber 1:3:6 type C1, of size 45X 45X 45 CM, RCC cover 1:2:4 type B1 of size 45X45X6 CM, excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old U/S earthing items complete all as specified and directed.

Supply and fix GI bracket pipe of size 40 mm dia medium grade of 1.0 mtr long bent to shape hot or cold suitable for street light fitting and making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixed on wall surfaces and including suitable fabricate MS flat iron clamps of 25X6 mm thick -02 Nos suitable for fixing any places with nuts,bolts & washers including grouting on wall etc complete all as specified and directed.

M & L for Multi meter box for housing of Energy meters including provision of door with hinges and locking arrangement of oute size 1040x730x290mm concealed on wall including cutting on wall and making good the disturbed sufaces with cement plaster including taking down of old unserviceable mete box complete all as specified and directed.

Excavation in trenches, in any type of soil not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr in depth , laying of cable or pipes (where provided for protection of cable) etc and getting out trimming the sides, forming bottom surfaces to required level complete all as specified and all as directed.

M & L for sand cushioning with a layer of sand 80 mm thick before laying of cable and 150 mm thick after laying of cable in trenches complete all as specified and directed.

Supply and laying of well burnt bricks, sub class 'B' laid flat in trenches for protection of cable complete all as specified and directed.

Returning and filling including spreading, levelling, watering and well ramming in layers not exceeding 25 Cm thick all as specified and directed by Engr-in-Charge.

Removing of surplus soil to a distance not exceeding 50 Mtrs and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified.

SHARMA CONSTRUCTION COMPANY

M/s Sekinder Paul Sharma

ASIA ENTERPRISES

JR CONSTRSTRUCTION CO.