MMPPNA_23_24_225 (1)Construction of Road from Naharani Balijan via Dizmur Hindu Gaon from Ch. 0.00 m to 1200.00 m including Cross Darinage works, (2)Construction of Road from NH-515 at Dimow Santipur to Bukajan from Ch. 0.00 m to 1000.00 m,

Amount

(1) Construction of Road from Naharani Balijan via Dizmur Hindu Gaon from Ch. 0.00 m to 1200.00 m Clearing and Grubbing Road Land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201. (i) By Manual Means (a) In area of non thorny jungle

Embankment Construction with Material Obtained from Borrow Pits: Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirment of table 300-2 ( including compensation of earth.( Including cost of testing of materials at site and laboratory as directed by the deptt.) (I) From private land.

Construction of sub grade & earthen shoulders : Construction of Sub grade & Earthen Shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading grading to required slope and compacting to meet requirement of Table 300.2 (including compensation of earth) (Including cost of testing of materials at site and laboratory as directed by the deptt.) i) From private land.

Granular Sub-base with coarse graded materials (Table : 400-2) : Construction of Granular Sub-base by providing coarse Graded Materials, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotovator at OMC and compacted with vibratory roller to achieve the desired complete as per cl. 401 (with an initial lead of 5.0 Km) i) For Grading I Material

Water Bound Mecadam : Providing laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification incuding spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tones capacity in stages to proper grade and camber, applying and brooming, requisite type of screening/binding material to fill-up the interstics of coarse aggregate, watering and compacting to the required density (With an initial lead of 5.0 km) (A) By manual means I) Grading II b)Using Screening Type A (13.2 mm Agg)

Water Bound Mecadam : Providing laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification incuding spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tones capacity in stages to proper grade and camber, applying and brooming, requisite type of screening/binding material to fill-up the interstics of coarse aggregate, watering and compacting to the required density (With an initial lead of 5.0 km) (A) By manual means III) Grading III b)Using Screening Type B (11.2 mm Agg)

Prime Coat : (i) Low Porosity Providing and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90- 1.2 kg/sqm using mechanical means as per Technical Specification Clause 502.

Tack Coat : (III) Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion pressure distributor at the rate of 0.30 to 0.35 kg per sqm on the prepared non bituminous surfaces (cement concrete pavement) cleaned with Hydraulic broom as per Technical Specification Clause 503.

Semi - Dense Bituminous Concrete: Providing and laying semi dense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5% of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.508. complete in all respect. including carriage of mixed materials up to 10.0 Km initial lead from mixing plant ) (Including cost of testing of materials at site and laboratory as directed by the deptt.) I With hydrated lime/ cement as filler (refer table 500-9 of MoSRT&H specification) A With 60/70 or VG-30 grade bitumen (ii) for Grading II (10 mm nominal size)

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) ii) 60 cm equilateral triangle.

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) (iii) 60 cm circular

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) (iv) 80cm x 60 cm rectangular.

Direction and Place Identification sign upto 0.9 sqm size board : Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on dia GI Pipe firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Kilometer stone : Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 iii) 200th meter stone (precast)

Providing and Fixing 'Logo' of PMGSY Project: Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges.The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface: Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications

RCC Box cell culvert 1.00m x 1.00m x 1 cell at ch 600.00m Removing of all types of Hupe Pipes and stacking within a lead of 1000 m including earth work and dismantling of Masonary works as per technical specificaction Clause 202. ( B) Above 600 mm to 900 mm

Earth Work for structute ( Earth work in excavation of foundation) (i) Ordinary Soil up to 3m depth

Plain/Reinforced Cement Conctre in open foundation. With natural gravel (B) I. PCC M-10 ( Nominal Mix) 1:3:6

Plain/Reinforced Cement Conctre in open foundation . With natural gravel (B) IV. RCC M-20

Back filling behaind abutment , wing wall (II) With Sandy materials

Plain/Reinforced Cement Conctre in open foundation . With natural gravel (B) III. PCC M-20 ( Nominal Mix) 1:2:4

Supplying fitting and placing TMT bar reinforcement in foundation Complete as per drawing and technical specification Clause 1000 &1202

RCC Box cell culvert 2.00m x 2.00m x 1 cell at ch 900.00m Excavation for Structures Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material, Ordinary soil Upto 3 m depth

11.2/ Filling in Foundation Trenches as per Drawing & Technical Specification sand

11.4 Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 II P.C.C grade M 15 Nominal mix (1:2.5:5)

11.4 Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 III P.C.C Grade M20 Nominal mix (1:2:4)

11.4 Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 IV R.C.C Grade M20

11.7 Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL) in foundation complete as per drawings and technical specifications Clauses 1000 and 1202

12.5 Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 A With Crushed Stone I P.C.C grade M 15 i) Nominal mix (1:2.5:5)

12.6 Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202

12.5 Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 A With Crushed StoneIII RCC Grade M 20 i) For height upto 5 m

13.5 Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3 A With crushed stone

12.14/Providing Pressure relief pipes 100 mm dia. In bottom slab of box cell on a filter media base of 500x 500 mm as per drawing and technical specfication clause 1205.5.7

12.5 Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 A With Crushed Stone I P.C.C grade M 15 i) Nominal mix (1:2.5:5)

14.10/Flexible Apron :Construction of flexible apron 1 m thick comprising of loose stone boulders weighing not less than 25 kg beyond curtain wall.

13.6/Construction of RCC railing of M25 Grade in-situ with 20 mm nominal size aggregate, true to line and grade, tolurence of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequat space between vertical posts for expansion, complete as per approved drawings and technical specifications.

12.10/Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification , 'II -Sandy material

17.49 Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specification

Utility Shifting

(2)Construction of Road from NH-515 at Dimow Santipur to Bukajan from Ch. 0.00 m to 1000.00 m Clearing and Grubbing Road Land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201. (i) By Manual Means (a) In area of non thorny jungle

Embankment Construction with Material Obtained from Borrow Pits: Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirment of table 300-2 ( including compensation of earth.( Including cost of testing of materials at site and laboratory as directed by the deptt.) (I) From private land.

Construction of sub grade & earthen shoulders : Construction of Sub grade & Earthen Shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading grading to required slope and compacting to meet requirement of Table 300.2 (including compensation of earth) (Including cost of testing of materials at site and laboratory as directed by the deptt.) i) From private land.

Granular Sub-base with coarse graded materials (Table : 400-2) : Construction of Granular Sub-base by providing coarse Graded Materials, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotovator at OMC and compacted with vibratory roller to achieve the desired complete as per cl. 401 (with an initial lead of 5.0 Km) i) For Grading I Material

Water Bound Mecadam : Providing laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification incuding spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tones capacity in stages to proper grade and camber, applying and brooming, requisite type of screening/binding material to fill-up the interstics of coarse aggregate, watering and compacting to the required density (With an initial lead of 5.0 km) (A) By manual means I) Grading II b)Using Screening Type A (13.2 mm Agg)

Water Bound Mecadam : Providing laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification incuding spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tones capacity in stages to proper grade and camber, applying and brooming, requisite type of screening/binding material to fill-up the interstics of coarse aggregate, watering and compacting to the required density (With an initial lead of 5.0 km) (A) By manual means III) Grading III b)Using Screening Type B (11.2 mm Agg)

Prime Coat : (i) Low Porosity Providing and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90- 1.2 kg/sqm using mechanical means as per Technical Specification Clause 502.

Tack Coat : (III) Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion pressure distributor at the rate of 0.30 to 0.35 kg per sqm on the prepared non bituminous surfaces (cement concrete pavement) cleaned with Hydraulic broom as per Technical Specification Clause 503.

Semi - Dense Bituminous Concrete: Providing and laying semi dense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5% of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.508. complete in all respect. including carriage of mixed materials up to 10.0 Km initial lead from mixing plant ) (Including cost of testing of materials at site and laboratory as directed by the deptt.) I With hydrated lime/ cement as filler (refer table 500-9 of MoSRT&H specification) A With 60/70 or VG-30 grade bitumen (ii) for Grading II (10 mm nominal size)

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) ii) 60 cm equilateral triangle.

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) (iii) 60 cm circular

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) (iv) 80cm x 60 cm rectangular.

Direction and Place Identification sign upto 0.9 sqm size board : Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on dia GI Pipe firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Kilometer stone : Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 iii) 200th meter stone (precast)

Providing and Fixing 'Logo' of PMGSY Project: Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges.The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface: Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications

Utility Shifting

(3)Construction of Road from Lamajan Bajar to Dimoruguri from Ch. 0.00 m to 1700.00 m Clearing and Grubbing Road Land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201. (i) By Manual Means (a) In area of non thorny jungle

Embankment Construction with Material Obtained from Borrow Pits: Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirment of table 300-2 ( including compensation of earth.( Including cost of testing of materials at site and laboratory as directed by the deptt.) (I) From private land.

Construction of sub grade & earthen shoulders : Construction of Sub grade & Earthen Shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading grading to required slope and compacting to meet requirement of Table 300.2 (including compensation of earth) (Including cost of testing of materials at site and laboratory as directed by the deptt.) i) From private land.

Granular Sub-base with coarse graded materials (Table : 400-2) : Construction of Granular Sub-base by providing coarse Graded Materials, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotovator at OMC and compacted with vibratory roller to achieve the desired complete as per cl. 401 (with an initial lead of 5.0 Km) i) For Grading I Material

Water Bound Mecadam : Providing laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification incuding spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tones capacity in stages to proper grade and camber, applying and brooming, requisite type of screening/binding material to fill-up the interstics of coarse aggregate, watering and compacting to the required density (With an initial lead of 5.0 km) (A) By manual means I) Grading II b)Using Screening Type A (13.2 mm Agg)

Water Bound Mecadam : Providing laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification incuding spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tones capacity in stages to proper grade and camber, applying and brooming, requisite type of screening/binding material to fill-up the interstics of coarse aggregate, watering and compacting to the required density (With an initial lead of 5.0 km) (A) By manual means III) Grading III b)Using Screening Type B (11.2 mm Agg)

Prime Coat : (i) Low Porosity Providing and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90- 1.2 kg/sqm using mechanical means as per Technical Specification Clause 502.

Tack Coat : (III) Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion pressure distributor at the rate of 0.30 to 0.35 kg per sqm on the prepared non bituminous surfaces (cement concrete pavement) cleaned with Hydraulic broom as per Technical Specification Clause 503.

Semi - Dense Bituminous Concrete: Providing and laying semi dense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5% of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.508. complete in all respect. including carriage of mixed materials up to 10.0 Km initial lead from mixing plant ) (Including cost of testing of materials at site and laboratory as directed by the deptt.) I With hydrated lime/ cement as filler (refer table 500-9 of MoSRT&H specification) A With 60/70 or VG-30 grade bitumen (ii) for Grading II (10 mm nominal size)

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) ii) 60 cm equilateral triangle.

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) (iii) 60 cm circular

Retro reflectorised Traffic Sign : Providing and erecting of Retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminum sheeting, 2mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cmx45cmx60cm, 60 cm below ground level as per approved drawing and sign. (All steel work must be Tata/SAIL or nay other approved brand) (iv) 80cm x 60 cm rectangular.

Direction and Place Identification sign upto 0.9 sqm size board : Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on dia GI Pipe firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Kilometer stone : Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 iii) 200th meter stone (precast)

Providing and Fixing 'Logo' of PMGSY Project: Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges.The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface: Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications

RCC Box cell culvert 2.00m x 2.00m x 1 cell Excavation for Structures Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material, Ordinary soil Upto 3 m depth

11.2/ Filling in Foundation Trenches as per Drawing & Technical Specification sand

11.4 Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 II P.C.C grade M 15 Nominal mix (1:2.5:5)

11.4 Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 III P.C.C Grade M20 Nominal mix (1:2:4)

11.4 Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 IV R.C.C Grade M20

11.7 Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL) in foundation complete as per drawings and technical specifications Clauses 1000 and 1202

12.5 Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 A With Crushed Stone I P.C.C grade M 15 i) Nominal mix (1:2.5:5)

12.6 Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202

12.5 Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 A With Crushed StoneIII RCC Grade M 20 i) For height upto 5 m

13.5 Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3 A With crushed stone

12.14/Providing Pressure relief pipes 100 mm dia. In bottom slab of box cell on a filter media base of 500x 500 mm as per drawing and technical specfication clause 1205.5.7

12.5 Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 A With Crushed Stone I P.C.C grade M 15 i) Nominal mix (1:2.5:5)

14.10/Flexible Apron :Construction of flexible apron 1 m thick comprising of loose stone boulders weighing not less than 25 kg beyond curtain wall.

13.6/Construction of RCC railing of M25 Grade in-situ with 20 mm nominal size aggregate, true to line and grade, tolurence of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequat space between vertical posts for expansion, complete as per approved drawings and technical specifications.

12.10/Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification , 'II -Sandy material

17.49 Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specification

Utility Shifting

(4) Construction of Road from NH-515 at Akajan Vaterinary Tiniali to Jun Nepali Gaon Clearing and Grubbing Road Land .(Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable materials to beused or auctioned up to lead of 1000metres including removal and disposal of top organic soil not exceeding 150mm thickness as per technical specification clause 201. (I) By manuals means. B. In the area of Non-thorny jungle.

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 (including compensation of earth) (Including cost of testing of materials at site and laboratory as directed by the deptt.). (a) From private land.

Granular sub-base with well graded material (table 400.1) (A). By mix in place method Construction of granular sub-base by providing well graded material in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC and compacting with smooth wheel roller to achieve the desired density complete as per technical Specification Clause 401. (ii) For Grading I Material and GSB in Hard Shoulder

Water Bound Macadam Sub-base/ base Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80 -100 KN in stages to proper grade and camber, applying and brooming stone screening/binding materials to fill up the interstices of coarse aggregate, watering and compacting to the reqd. density Grading 3 as per Technical Specification Clause 405. (A) By Manual Means

Inter locking concrete Block pavement (i) Providing and laying interlocking concrete block pavement with M40 grade grade of concrete blocks having thickness 80mm as per technical specification clause 1504 complete including carriage. a) Including Edge block/ Edge restraints

Planting of Trees and their Maintenance for three Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trenches, watering , fixing the tree guatrd and maintaining the plants for one year .

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 ii 600mm equilateral triangle

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 (iv)80 cmx 60 cm rectangular

HPC Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.

PCC M10(1:3:6 nominal mix) in levelling course below open foundation of Head walls as per drawing and technical specification clause 1109

Laying 1st class bedding on well compacted sand, moorum as per clause 115(ii)Granular bedding

Brik masonry work in cement mortar in foundation of wall complete excl. pointing and plastering as per drawing and technical specification clause 1100(in prop. 1:4)

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. B)1000mm dia.

Plastering with cement mortar(1:6) 15mm thick on brick work for substructure as per technical specification

(5) Construction of Road from Jariguri Tiniali to Jariguri Assamese Tiniali Clearing and Grubbing Road Land .(Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable materials to beused or auctioned up to lead of 1000metres including removal and disposal of top organic soil not exceeding 150mm thickness as per technical specification clause 201. (I) By manuals means. B. In the area of Non-thorny jungle.

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 (including compensation of earth) (Including cost of testing of materials at site and laboratory as directed by the deptt.). (a) From private land.

Granular sub-base with well graded material (table 400.1) (A). By mix in place method Construction of granular sub-base by providing well graded material in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC and compacting with smooth wheel roller to achieve the desired density complete as per technical Specification Clause 401. (ii) For Grading I Material

Water Bound Macadam Sub-base/ base Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80 -100 KN in stages to proper grade and camber, applying and brooming stone screening/binding materials to fill up the interstices of coarse aggregate, watering and compacting to the reqd. density Grading 2 as per Technical Specification Clause 405. (A) By Manual Means

Water Bound Macadam Sub-base/ base Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80 -100 KN in stages to proper grade and camber, applying and brooming stone screening/binding materials to fill up the interstices of coarse aggregate, watering and compacting to the reqd. density Grading 3 as per Technical Specification Clause 405. (A) By Manual Means

Prime-Coat ( I) Low porosity Providing and applying primmer coat with bitumin emultion (CSS-1) on prepared surface of granular base /WBM/WMM including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per technical Clause 502.

Tack-coat (III) Providing and applying tack coat with bitumin emultion (CRS-1) using emultion distributor at the rate of 0.25-0.30 Kg/sqm on the prepared granular surface treated with primer & cleaned with hydraulic broom as per technical specification clause 503.

Semi - Dense Bituminous Concrete (Providing and laying semi dense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5% of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.508. complete in all respect. (i)

Planting of Trees and their Maintenance for three Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trenches, watering , fixing the tree guatrd and maintaining the plants for one year .

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications. (80% length of the Road is considered)

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 i 800mm x600mm rectangular

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801 ii 600mm equilateral triangle

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. i)Ordinary KM Stone

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. i)200M Stone

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 (iv)80 cmx 60 cm rectangular HPC

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.

PCC M10(1:3:6 nominal mix) in levelling course below open foundation of Head walls as per drawing and technical specification clause 1109

Laying 1st class bedding on well compacted sand, moorum as per clause 115(ii)Granular bedding

Brik masonry work in cement mortar in foundation of wall complete excl. pointing and plastering as per drawing and technical specification clause 1100(in prop. 1:4)

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. B)1000mm dia.

Plastering with cement mortar(1:6) 15mm thick on brick work for substructure as per technical specification