SPECIAL REPAIR TO BLDG NO P-172 CGC AT GRC KAMPTEE.

Amount

Demolition of plain cement concrete in ground floor & paving not exc 15 cm thick above or below ground level complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub-base, under floors and pavings complete all as specified and directed.

Material & labour PCC (1:3:6) Type C1 (using 20 mm graded stone aggregate), 75 mm thick as in plinth protection and finishing surfaces even & smooth without using extra cement including mist filling in the joint complete all as specified and directed.

M&L for 100 mm thick PCC 1:2:4 type B2 (20 mm aggregate) as in Hard standing and similar works finished even and smooth without extra complete all as specified and directed.

S&F Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A' complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for mild steel angle iron as in framed chowkats for door shutters cut to length including necessary welding and making holes for fixing butt hinges and fixing 10 mm dia as tie bar complete confirming to Fe-410 -W (Gde E-250) quality A etc all complete all as specified and directed.

S&F framed guard bars with mild steel Square bars with ends of bars shouldered and/ or riveted and similar work confirming to FE 410-O or FE 310-0 complete all as specified and directed

S &F m/s hold fast and other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolt complete all as specified and directed.

Taking down existing water proofing treatment including PCC padding, mortar etc and disposal rubbish out side within MD land and hacking for key scrubbing down with water complete all as specified and directed.

M & L for 25mm thick PCC 1:2:4 type B0 (Using 12.50 mm graded stone aggregate) as in padding over RCC roof complete all as specified and directed.

Material & labour for provision of water proofing treatment by using APP torch on mineral/slate finished membranes over roof and vertical surfaces including preparation of surfaces and applying oil based bituminous primer coat @ 0.30 ltr per sqm on clean and dry surface and then providing APP membrane having non woven. polyester film reinforcement with 3 mm thick and weight not less than 3 .00 kg/sq m and finished on top with mineral/slate finished torch on system laid with 100 mm & 150 mm over lap on side & end laps respectively complete all as per manufacturers instructions complete all as specified and directed.

M&L for rendering 10 mm thick in cm 1:4 on brick or concrete surfaces using water proofing liquid compound and finishing surfaces even & fair without using extra cement. complete all as specified and directed. Note: water proofing liquid will be measured and paid separately.

Taking down shutters only exc 1 sqm & n exc 2 sqm each complete all as specified and directed.

Taking down door/window frames incl. shutters (without taking of shutter from the frames)n. exc 1.50 Sqm each complete all as specified and directed.

Taking down door/ window frames incl. shutters (without taking of shutter from the frames) exc 1.50 Sqm and not exc 4 sqm complete all as specified and directed.

S&F steel window with side hung shutters ( glaze & gauze shutter) including projecting or box type hinges with steel handle peg stay and divided into square with glazing bars dovetailed or welded, to receive glazing, or gauzing including one coat of primer including fixing of hold fast of size 25 x 5 mm flat iron etc complete all as specified and directed.

All as per item No 16 above but with glazing/sash bars for fly proofing complete all as specified and directed.

S&F 35 mm thick plain framed panelled factory made shutter made out of IInd class hard wood rail and styles and panel of 12 mm thick veneered particle board or 9 mm thick plywood with commercial veneering on both faces the size of rail and style as per IS 1083 (part-I) kiln seasoned an chemically pressure treated of any number of panel as complete all as specified and directed.

S & F Second class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S&F 35 mm thick 2nd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats or frame etc any numbers of panels or complete all as specified and directed.

S&F Solid PVC Door Frame of size 50 mm x 47 mm made out of 5mm colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specified and as directed.

S/F Factory made solid PVC moulded panelled door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails ,MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having PVC sheet strip of 20 mm width struck inside with solvent cement for styles and colour PVC sheet for Top rail : panelling of colour PVC sheet to be fitted in the MS frame welded/sealed to the style and rail with suitable PVC sheet beading and jointed together with solvent cement etc fixed with frame at site complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including ashlar facing dressed stone and pre-cast concrete articles complete all as specified and directed.

M & L for brick work with fly ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6(Using old size brick) complete all as specified and directed.

M & L for brick work with fly ash brick, straight or curved on plan to any radius built in half brick thick wall built in cm 1:4 (Using old size brick) complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls/chajja/pillars etc including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L for rendering 15 mm thick in two coats (10 and 5mm thick) in cm 1:4 on brick or concrete surfaces even & fair smooth, using water proofing liquid compound and without using extra cement complete all as specified and directed. Note: water proofing liquid will be measured and paid separately.

Supply only liquid integral water proofing admixture of make pidilite or its equivalent complete all as specified and directed.

M & L for rendering 10 mm thick CM 1:6 on brick or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

M & L for rendering 5mm thick CM 1:3 on brick or concrete surfaces of ceiling /chajja's finished even & smooth without using extra cement complete all as specified and directed for taking down plaster portion complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding, but not backing removing serviceable tiles to store and rubbish off the premises up to 1 KM complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in CM 1:4 finished fair and even for laying floor finishes/tiles etc complete all as specified and directed.

M&L for 10mm thick vitrified ceramic tiles (Square/rectangular ) polished, area of each tiles not exc 0.36 sqm, in floors/skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding/rendering layer 10-15mm thick mortar in CM 1:4 finished even and smooth for laying floor finishes complete all as specified and directed.

All as per item No 34 above but in skirting/dado including rendering 10mm thick in CM 1:3 as backing coat to receive tiles complete all as specified and directed.

M&L coloured glazed ceramic wall tiles 300 x 450 x 7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles including rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 as backing coat to receive wall tiles/skirting/dados complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4), type B0 (using 12.5 mm graded stone aggregate) as in sunken floor using liquid integral WPC @ 200 ML/50Kg of cement (WPC shall be measured and paid separately.) complete all as specified and directed.

M&L for PCC (1:5:10) type E2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer of cement plaster 1:4 with water proofing compound for sunkan floor treatment finishing even and smooth without using extra cement complete all as specified and directed. (WPC will be paid separately).

M&L for two coats of brush bond liquid compound of make Sika/ fosroc or its equvalent water proofing coating over plastered surfaces of sunken portion (Sika/Fosroc chemical Ltd) as per manufacturer's instructions complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for pre- polished granite slab machine cut of any shade as approved by GE of 18 to 20 mm thick including necessary notching, chamfering the edges over cement screed bed including Cutting, Grinding and Mirror polishing(Granite finish) with suitable grinding stones complete all as 'specified and as directed.

Rounding to edges of stone slabs one edge , such as in steps ,cooking platforms, and other similar situations.

M&L for 18-25 mm thick kota stone (machine cut) slab flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing over and including screed bed 20mm thick in CM 1:3 complete all as specified and directed by Engr-in-Charge

Material & Labour for Kota stone slab 12-20mm thick in riser of steps, skirting, dado and pillar laid over backing coat of 10mm cement screed in CM 1:3 complete all as specified and directed.

M & L for PCC 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) 25 mm thick as in levelling course, fair finished to receive floor finishes complete all as specified and directed

Material & labour plain cement concrete Type 1:2:4 B1 using 20 mm graded stone aggregate as in coping, haunching rounded or chamfered on edges including necessary from work complete all as specified and directed.

S&Fin repair PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S & F stack clamp made out of 50x5 mm flat iron for 75 mm dia of pipe complete all as specified and directed.

S & F stack clamp made out of 50x5 mm flat iron for 100 mm dia of pipe complete all as specified and directed.

S&F in repair PVC (SWR) Bends any radius for 110 mm bore complete all as specified and directed

S&F in repair PVC (SWR) Bends any radius for 75 mm bore complete all as specified and directed

S&F in repair PVC (SWR) branch piece single Y equal or unequal for 110 mm bore complete all as specified and directed

S&F in repair PVC (SWR) branch piece single Y equal or unequal for 75 mm bore complete all as specified and directed

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth complete all as specified and directed

S&F PVC (SWR) / rain water pipes 150 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.(including taking down existing pipe of any description)

S&F PVC (SWR) Bends any radius for 150 mm bore complete all as specified and directed

Taking up or down steel tubing 15mmdia bore and connections including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 20mmdia bore and connections including cleaning for refixing or removal to store complete all as specified and directed.

Supply & fix GI tubing 15 mm bore medium grade with all fittings and fixed to wall/ceiling or laid in floors complete all as specified and directed

Supply & fix GI tubing 20 mm bore medium grade with all fittings and fixed to wall/ceiling or laid in floors complete all as specified and directed

S & F PVC (SWR) Nahani trap 75 mm dia with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) complete all as specified and directed

S& F vitreous China squatting pan, ‘Orissa’pattern size 580x440 mm with integarals foot rests( excluding cistern and flush) type including all fixtures complete all as specified and directed

Supply and fixing PVC valve less symphonic action type flushing cistern 10ltr capacity low level, white/coloured with inlet ball valve float and handle including bracket(incl. taking down old cistern ) complete all as specified and directed.

Supply only flush pipe of polythene of low or high density 32 mm PVC for low level flushing cistern complete all as specified.

Supply only PVC connection 15 mm dia, 450-600 mm long including brass ferrules on both ends complete all as specified and directed

Supply only low density PVC pipe 32/40 mm dia as in waste pipe to sink/WHB complete all as specified and directed

S&F in repair towel rail make Prayag Cat No BA-30 complete all as specified and directed

S&F in repair Bib taps, chromium plated with crutch or butterfly handle, fancy type, screwed down screwed for iron pipe or for brass ferrule and fixed completed all as specified and directed

S&F in repair 15mm dia stop valves, fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed complete all as specified and directed

S&F in repair 15mm dia stop valves, fancy type and chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions and fixed complete all as specified and directed

S&F in repair pillar taps, cast copper alloy, with capstan heads, chromium plated, swan neck screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed

S&F Stainless steel sink with draining board,made out of 1.00mm thick sheet for kitchenor laboratory with plug, washers waste pipe, cast iron cantilever brackets,connecting union overall size915mmx460mm with bowl size 410mm x330mm x 160mm complete all as specified and directed

S&F in rep Vitreous china wash basin, white, flat back, size 630x450mm counter sunk oval type fixed in granite excluding taps, waste, chain and plug and porcelain stopper complete all as specified and directed.

Dismantling water tank of capacity 5000 ltrs and removing to store of any description complete all as specified and directed

S & F Rotational moulded polyethylene water storage tanks 6 layers (cylindrical vertical with closed top) 5000ltr hoisted and fixed in position including dismantling water tank complete all as specified and directed

M & L for preparation of new surfaces and applying two coats of exterior grade weather proof paint over a coat of primer, water based on wall surfaces all as specified and directed

M & L for preparation of old decorated surfaces and applying two coats of exterior grade weather proof paint over a coat of primer, water based on wall surfaces all as specified and directed

Material & labour for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of cement primer complete all as specified and directed

M & L Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of Birla white care putty complete all as specified and directed

M & L for complete removal of existing treatment of walls and applying two coats of oil bound distemper over a coat of Birla white care putty complete all as specified and directed

M & L for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed

M&L for Preparation of old wooden surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over coat of primer complete all as specified and directed

M & L for preparation of old steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint complete all as specified and directed

M & L for preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm dia complete all as specified and directed

S & F 100 mm long Mild steel medium weight cold rolled butt hinges and fixed with screw/welded to frames etc all as specified and as directed

S&F in repair 125 mm Extruded Aluminium handles fabricated type anodised etc complete all as specified and directed

S & F in repair 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and directed

S & F in repair 150 mm long aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed

S & F in repair 75 mm long aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed

M & L for Hacking out old broken glass any thickness size and quality from wooden/steel frames etc complete all as specified and directed

S & F sheet glass ordinary quality, 3 mm thick and glazing with oil putty in square n. exc. 0.50 Sqm in each pane complete all as specified and directed

S & F 3 mm figured glass, pin head type and glazed with oil putty in sqm n exc 0.50 sqm in each pane complete all as specified and directed

Supply and fixing anodised aluminium frame for doors, windows, ventilators (powder coated of any colour (thickness or powder coating not less than 50 micron)) with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F anodized aluminium door shutters aluminium (powder coated of any colour (thickness or powder coating not less than 50 micron)) section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed.

S&F anodized aluminium windows and ventilator shutters (powder coated of any colour (thickness or powder coating not less than 50 micron)), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

S & F sheet glass ordinary quality, 4.00 mm thick and glazing with oil putty in square n exc. 0.50 Sqm in each pane complete all as specified and directed

S&F for sheet glass 5.50 mm thick tinted quality and glazing complete all as specified and directed by Engineer-in-Charge exc 0.50 sqm in each panal complete all as specified and directed

S&F brass mortise lock (4 levers), vertical type, size 100mm long including all fitting arrangements complete all as specified and directed

S & F Heavy duty Al body floor door spring (ISI marked) suitable for Al swing doors, double action type including necessary cutting in floors and making good to match with the existing surface complete all specified and directed.

M&L for Ball brass valves.high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 20mm bore Complete all as specified and directed.

S&F for Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe) Complete all as specified and directed.

M&L 20mm thick marble machine cut in skirting/ dado/cill/lintels /floor/jams laid over cement screed and jointed with grey cement slurry including cutting and polishing of type as approved complete all as specified and directed

S & F 20 mm thick solid pvc boarding of make rajshree or equivalent as in partition of interior grade complete all as specified and directed

S&F for 25mm dia curtain rod of approved quality including cutting and fixing to curtain brackets complete all as specified and directed.

S&F for fancy type curtain brackets of approved quality fixed to wall with screws complete all as specified and directed

Demolition of reed lathing, single or double including battens and plaster or chicken wire lathing, RCC jali complete all as specified and directed

S&F in rep Providing precast cement concrete type B0 1:2:4 (12.5 mm graded aggregate) louvers and jallies 35 mm thick (measured solid) including all mouldings but excluding frame and fixed complete all as specified and directed

M&L for running welding in repairs including cleaning and preparing surfaces for welding, thickness of metal to be welded not exc 6mm such as MS butt hinges to MS frame, broken steel windows or ventilator, iron doors and similar work complete all as specified and directed.

M&L for cutting & taking out the existing surface / sunken box / switch plate with switches / sockets and replacing with the following items complete all as specified and directed for: Modular metal flush box with modular cover plate with frame 3 module. Note:- The disturbed surfaces of wall for concealing box wiring shall be made good by applying cement plaster, putty and colour wash etc matching with the existing surfaces. The rate shall be deemed to include the cost of making good. Switches, sockets, regulators etc to be measured and paid separately.

All as per item no 114 but Modular metal flush box with modular cover plate with frame 4 module complete all as specified and directed

All as per item no 114 but Modular metal flush box with modular cover plate with frame 6 module complete all as specified and directed

All as per item no 114 but Modular metal flush box with modular cover plate with frame 8 module complete all as specified and directed

All as per item no 114 but Modular metal flush box with modular cover plate with frame 12 module complete all as specified and directed

Supply and fixing for switch modular type single pole one way 6 amp 1 module 250 volts AC suitable for modular switch boxes, complete all as specified and directed.

Supply and fixing for socket modular type single pole one way 6 amp 2 module 2/3 pin 250 volts AC suitable for modular switchboxes, complete all as specified and directed.

Supply and fixing for switch modular type single pole one way 6/16 amp 3 pin 250 volts AC suitable for modular switch boxes, complete all as specified and directed.

Supply and fixing for socket modular type single pole one way 6/16 amp 2/3 pin 2 module, 250 volts AC suitable for modular switch boxes, complete all as specified and directed.

Supply and fixing 0-4 step -2 module modular type electronic regulators for ceiling fan 1200/1400 mm sweep, 240 volts, 120 watts single pole complete all as specified and directed.

Supplying and fixing 18-22 Watt LED Tube light fittings complete with aluminum body including tube rod, driver with not less than 2000 Lumen O/P and I/p rated voltage 240V connecting with 3 core 1 sqmm copper conductor cable complete all as specified and directed.

Supply and fix LED baton fitting 2' length including drivers having energy consumption, 10/11W ,230 V ,50Hz, 6500K, not less than 800 lumen prewired, complete all as specified and directed

Supply & fix fittings with recessed typet LED down lighters 12 W, round/square as specifiedby EIC including driver with rated voltage 240 V , 50 Hz, complete all as specified and directed

Supply and fix building security light LED 25 W with Lumen O/P 1800 with driver with rated voltage 240 V, 50Hz,including mounting GI (made out of 25 mm dia light grade pipe 0.8 m bent two shape including FI clamps nut bolts etc. complete all as specified and directed

Supply and Fix sheet metal enclosure for vertical Triple Pole and Neutral (VTPN) suitable for MCCB 100 A , 415 Volts, 50 Hz, with IP 54 protection made out of CRCA sheet complete with all connection complete all as specified and directed

Supply and fix sheet metal enclosure triple pole & neutral for 415 volts 4 way with 200 Amp rated bus bar flush /surface mounting, double door, complete all as specified and directed

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 8 way with 200 Amp rated bus bar flush /surface mounting, double door, complete all as specified and directed

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 4 way with 200 Amp rated bus bar flush /surface mounting, double door, complete all as specified and directed

Supply and fix MCB Triple pole & neutral 240 volt 40 to 63 amps 10 KA, complete all as specified and directed.

Supply and fix MCB single pole & neutral 240 volt 6 to 40 amps 10 KA, complete all as specified and directed.

Supply and fix MCB single pole 240 volt 6 to 40 amps 10 KA, complete all as specified and directed.

Earthing complete with galvanised steet earth plate electrode 600x600x6mm thick burried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr. below the normal ground level connected to galvanised earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washer of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified and testing on completion including the material and labour for :- (a) Excavation and earth work or drilling hole for electrode in any type of soil (b) PCC pit in cement concrete 1:2:4 TYPE B-1 (c) Pre cast RCC cover with suitable handle 40mm thick in PCC 1:2:4 reinforced with welded steel wire fabric (d) Funnel with watering pipe of GI 20mm nominal bore light grade and copper lugs etc all as specified. (e) 15mm nominal bore meduim grade GI protec-tion pipe 7.50 metre long for protection of earthing lead. (f) Requisite quantity of charcoal and common salt (g) Connection to earthing test point and testing on completion.

NOTE:- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs. 64,582.00]

SHIV SHANKAR MISHRA

M/s T.S.JOHAR

Alert Multipurpose Services

DEESHA CONSTRUCTIONS

M/s Jagdish Staioners and General Stores

NORTH INDIA PEST CONTROL

Bidder Name

SHIV SHANKAR MISHRA

DEESHA CONSTRUCTIONS

CREATIVE CONSTRUCTION

Alert Multipurpose Services

M/s Jagdish Staioners and General Stores

NORTH INDIA PEST CONTROL

M/s T.S.JOHAR