Construction Work

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Centering and shuttering including strutting, propping etc. and removal of form work for : Columns, piers, abutments, pillars, posts and struts

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: aggregate 20 mm nominal size) - 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete - Hot finished welded type tubes

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood etc.) shutter including chowkhats, architrave, holdfasts, glasses etc. complete and stacking within stacking yard in different lots one as a servicible and another as an unservicible as directed by Architect or Engineer-in-Charge.

Of area 3 sq. metres and below

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: G.S. Sheet

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: Asbestos Cement sheet

Dismantling the Water Supply & Sanitary lines, fittings like wash basin, EWC, IWC, urinals, Sink, SCI sanitary lines etc complete and stacking the same within 50m lead

Old block

Dismantling electrical panel boards, Genset and electrical items like fan, electrical fittings, cables, AC units, telephone cables, pipes etc complete including lawn lights and stacking the same within 50m lead

Old block

Dismantling and stacking of existing 6 passenger capacity, Ground + 1 floor landing lift machine including railing and cabin etc complete and stacking the same within 50m lead

6 Passenger G+1 floor landing Lift (30 Years Old)

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for the following leads for all lifts, complete as per directions

for lead upto 10 km

Extra for lead beyond 10 Km to 20 Km ( Rate per km)

Extra for lead beyond 20 km to 30 km lead ( Rate per km)

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

All kinds of soil - Lift upto 1.5m

All kinds of soil - Lift from 1.5m to 3.0m depth

All kinds of soil - Lift from 3.0m to 4.5 m depth

All kinds of soil - Lift from 4.5 m to 6.0m depth

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. Ordinary rock / Building basement rubbish material

Ordinary rock upto 1.5m depth

Ordinary rock between 1.5m to 3.00m (1 Lift extra)

Ordinary rock between 3.0 m to 4.5m (2 Lift extra)

Ordinary rock between 4.5 m to 6.0 m (3 Lift extra)

Ordinary rock between 6.0 m to 7.5 m (4 Lift extra)

Ordinary rock between 7.5 m to 9.0 m (5 Lift extra)

Ordinary rock between 9.0 m to 10.5 m (6 Lift extra)

Ordinary rock between 10.5 m to 12.0 m (7 Lift extra)

Ordinary rock between 12.0 m to 13.5 m (8 Lift extra)

Ordinary rock between 13.50 m to 15.0 m (9 Lift extra)

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge : Hard rock (blasting prohibited)

4th Lift - Depth below 6.0 m and upto 7.5m from existing ground level

5th Lift - Depth below 7.5 m and upto 9.0 m from existing ground level

6th Lift - Depth below 9.0 m and upto 10.5 m from existing ground level

7th Lift - Depth below 10.50 m and upto 12.0 m from existing ground level

8th Lift - Depth below 12.00 m and upto 13.5 m from existing ground level

9th Lift - Depth below 13.5 m and upto 15 m from existing ground level

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Removal and disposal of surplus earth by mechnical transport including loading, transporting, unloading to approved municipal dumping ground for the following leads for all lifts, complete as per directions

Lead upto 5km

Extra for lead beyond 5 km to 10 Km

Extra for lead beyond 10 Km to 20 Km

Extra for lead beyond 20 Km to 30 Km

Removal and disposal of excavated rock by mechnical transport including loading, transporting, unloading to approved municipal dumping ground for the following leads for all lifts, complete as per directions

Lead upto 5km

Extra for lead beyond 5 km to 10 Km

Extra for lead beyond 10 Km to 20 Km

Extra for lead beyond 20 Km to 30 Km

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level - Concrete of M40 grade with minimum cement content of 390 kg /cum .

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

All works above plinth level upto floor V level - Concrete of M30 grade with minimum cement content of 350 kg /cum

All the works above floor V level for each four floors or part thereof.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured). Height from 4.5m to 24.5m

Height upto 5.5m.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto and above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Supplying and fixing of EN8D Couplers and threading of rebars as per standard specification

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound.

(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer.

Using rough kota stone

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge :

Using rough kota stone.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and applying crystalline mortar by mixing in the ratio of 4.5 : 1 (4.5 parts crystalline mortar : 1 part water) for the treatment of faulty construction joints, cracks, tie rod holes and spalled & honeycombed surface of RCC underground structures like basement, water tanks, bridge deck etc. to ensure water tightness. The crystallie mortar shall conform to the EN 1504-3 having compressive strength Class R4 ?45 MPa and adhesive bond strength Class R3 ?1.5 MPa. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

For patching of tie rod holes, prepared tie rod hole surface and then primed the area with integral crystalline slurry @0.070kg/sqm and while the surface is tacky repair and then filled the tie rod holes with crystalline [email protected] per hole. The crystalline mortar should be tightly rodded into tie rod holes or packed tightly (For 25x25x25 mm tie rod hole, use 0.040kg to fill the hole).

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) AND Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:4 (1 cement : 4 coarse sand).

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above floor V level in : Cement mortar 1:4 (1 cement : 4 coarse sand). Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level. Cement mortar 1 : 4 (1 cement : 4 coarse sand). Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above floor V level. Cement mortar 1 : 4 (1 cement : 4 coarse sand). Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means. Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and fixing soil, waste and rainwater sound insulated Polyproplene piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 18- 22 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe not more than 1.25gms/m3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with including all necessary fittings, holder bat clamps, alround PP Pipe including bed concrete (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) , fitted with factory fitted lip ring.

40 mm dia

110 mm dia

160 mm dia

Providing and fixing floor drain with 50mm outlet and 100 mm inlet with SS grating having 50mm seal for indirect floor drain

Providing and fixing end cap (door piece) of pp for cleaning. -

with 110 OD

with 160 OD

Providing and fixing PP 110mm P Trap with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections.

Providing, fixing, testing and commissioning of pipe inlet fittings fabricated with Polyproplene Pipe with maximum 3 inlets 40, 50 & 75 mm OD size Polyproplene pipe, fixed to 'P' traps including Dripseal/Pipe seal/solvent /rubber ring joint complete.

Providing and installing Air Admittance valves with required air flow rate, including submission of design data. Airflow capacity upto 26-32 l/s ( Maxi Vent )

Airflow capacity upto 26-32 l/s ( Maxi Vent )

Airflow capacity upto 7.5 - 7.6 l/s ( Mini Vent )

Providing & fixing of F.R.P. Grating (Heavy Duty) for channel drains including all accessoreis complete capable to bear 5.0 T Load. 488/485 wide x 40mm thk. - Drain Cover

Providing & fixing of F.R.P. MH Cover with frame 600 mm dia dimensions for basement sump. ( capable to bear 5.0.0 T Load ).

Providing and fixing Circular type 125 mm nominal dia stainless steel cockroach trap.

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) For roof level

25 mm dia, nominal bore

40 mm dia, nominal bore

50 mm dia, nominal bore

80mm nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

25 mm dia, nominal bore

40 mm dia, nominal bore

50 mm dia, nominal bore

80mm nominal bore

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

100 mm dia, NB

150 mm dia, NB

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required

80 nominal bore

100 nominal bore

Providing and fixing brass stop cock of approved quality

15mm nominal bore

20mm nominal bore

Structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931.

15mm nominal bore

Constructing masonry chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement:4 fine sand) for sluice valve, with C.I. surface box 100mm, to diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

65 nominal bore

80 nominal bore

100 nominal bore

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on gyeser and solar water pipe suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

100mm dia

Providing and fixing of Polyethylene Raised Temperature (PE-RT) Piping system with D-2388 material as per PN-16 in accordance with ISO 10508,PERT Grade-2 for Hot and Cold water application with corresponding hot fusion welded PERT fittings in PN-16 like Tee's, Elbows, Sockets, Reducers, Unions, brass adaptors (both male female) etc. conforming to ISO 10508 standards. Further all termination points should be brass fittings only for connection with faucets. Installation guidelines should be strictly followed as per the company's technical literature. Further the system should bear a maximum pressure of 16 Bar at 20 Degree centigrade and a pressure of 5 Bar at 95 degree centigrade.

20 mm PERT

25 mm PERT

32 mm PERT

40 mm PERT

50 mm PERT

63 mm PERT

90 mm PERT

110 mm PERT

Providing and fixing brass ball valve with SS 304 Stem and ball, teflon seat complete (PN-16).

15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

Providing, fixing, testing and commissioning of motorised butterfly valve of following dia for filling of overhead water tank complete with high and low level control switches to control tanks. The level controllers shall be installed in iverhead tanks. The level switch will close the valve when water level is high in overhead tank and open the valve when overhead water tank level is low. The system should be complete in all respects with accessories 220 V AC / 2 V DC, IP67 electrical water level control unit, copper control wiring in whether proof casing etc.

50 mm dia NB Float Valve

Supply, erection, testing & commissioning of solar water heating system with following details :

Collector Stand : 35x35x3 mm MS angle Hot Water Tank : Cylindrical - vertical / horizontal, Stainless steel 304 grade with 100 mm thick Rock Wool insulation including 22 SWG aluminium cladding. The entire system should be complete with internal piping in SS(304) with 50 mm rock wool insulation of density 48 kg/m3 with 26 SWG Al cladding, necessary isolation valves, Y type CI strainer, hardwares, temperature gauge of range 0 - 120oC, water meter, MS angle iron structure of min thickness 3 mm duly painted etc as required to complete the system in all respects. The entire system should be approved by BIS as per IS : 12933 and as per local regulations. System Capacity : 1000 liters ( storage tank of 5,000 litres ) per day (LPD) having 10 collectors

System Capacity : 1000 liters ( storage tank of 5,000 litres ) per day (LPD) having 10 collectors.

Supply , installation , testing & commissioning of Micro Processor Controlled air cooled Heat pump delivering actual capacity as per the following parameters duly installed at site

Heat pumps shall be rated at 6.02 KW of input power and 19.8 KW of output power. Refrigerant used should be environment friendly R-410a. Heat pump should heat water upto 55⁰C on heat pump mode. It shall have silent operation and the sound level should not exceed 65 dB. Refrigerant R-410a/6.2 kg (Refrigerant) Heat Pump as described above Nominal Input Power - 6.03 KW Output Heating capacity - 19.8 kW All other mounting, fitting and controls Suitable for electric supply of 415 + 10 % volts & 50 hz All inter connecting wiring/cabling between heat pump and electric panel The heat pump shall have an in-built facility to start /stop depending on variation in demand at different periods

Supply, Installation, Testing and commissioning of wall hanging drinking water fountain with bottle filler facility, made by stainless steel top and heavy duty galvanized steel frame. With cooling capacity 8GPH,ADA Compliant, size 472 mm Depth X 447mm width, flexible bubbler guard , operated between 50 to 120 PSI, Chiller unit Suitable to R134a Refrigerant, Adjustable thermostat control, suitable for 220-230v/50-60 hz A/C Supply Complete with all ccessories.

Providing laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design.

150 mm diameter

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for stoMetre drainage)

250 mm dia RCC pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design.

250 mm dia RCC pipe

Constructing brick masonry manhole with F.P.S. bricks in cement mortar 1 : 4 (1 cement : 4 coarse sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1cement 3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finishd with a floating coat of neat cement complete as per standard design

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manhole with F.P.S. bricks

size 90 X 80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar confoMetreing to IS : 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's peMetreanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing square mouth SW gully trap grade ‘A’ complete CI grating brick masonry chamber with bricks of class designation 75 and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. (COVER MIN. 4.5 KG & FRAME MIN.2.7 KG )

180x150 mm size P type With FPS bricks

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement cincrete 1:2:4 mix (1cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete for pipes 100 to 250mm dia.

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for stoMetre drainage)

150 mm dia RCC pipe

250 mm dia RCC pipe

300 mm dia RCC pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design.

150 mm dia RCC pipe

250 mm dia RCC pipe

300 mm dia RCC pipe

Constructing brick masonry road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:5 (1 cement : 5 fine sand) including 500 x 450 mm (heavy duty) precast RCC horizontal grating with frame complete as per standard design:

with FPS bricks

Earth work In excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth. 1.5m in width as per as 10 Sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be levelled and neatly dressed.

All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating Each deposited layer by ramming and watering , lead up to 50 m and lift up to 1.5m.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - all work upto plinth level.

1:4:8 (1 cement :4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in:

Cement mortar 1:4 (1 cement: 4 coarse sand)

Centring and shuttering including strutting, proppintg etc. and removal of foMetre for:

Suspended floors,roofs, landings, balconies and access platfoMetre.

Edges of slabs and breaks in floors and walls, - Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

TheMetreo Mechanically Treated bars.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

L D- 2.5 Rectangular shape 600x450mm internal dimensions

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.

Providing & fixing on wall face unplasticised -Rigid PVC rain water pipes confoMetreing to IS:13592 Tyape A included jointing with seal ring conforning to IS:5382 leaving 10 mm gap for theMetreal expansion. (i)Single socketed pipes.

110 mm diameter

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS:2800(Part I ), including collecting sample from different strata , preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90m depth below ground level.

All types of Soil - 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing (CM) pipe of required dia, confoMetreing to IS: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of Engineer-in-charge.

150mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen(MetreS) pipes with ribs, confoMetreing to IS: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of Engineer-in-charge.

150 mm nominal size dia

Supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling coarse sand of size range 1.5mm to 2mm, in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tube well as per IS:2800 (part I).

100 mm dia

Providing and fixing G.I. pipes complete with G.I. fittings including ,trenching and refilling etc. external works

25mm nominal bore

50mm nominal bore

80mm nominal bore

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality

25 mm dia, nominal bore

50 mm dia, nominal bore

80mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25mm nominal bore

50mm nominal bore

80mm nominal bore

Providing and filling sand of grading zone V or coarser grade all-round the G.I. pipes in external work.

25mm nominal bore

50mm nominal bore

80mm nominal bore

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :

50 mm dia

80 mm dia

Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately)

100 mm dia.pipe

Constructing masonry chamber 30x30x50 cm,inside with 75 class designation brick work in cement mortar 1:4 (1 cement:4 coarce sand) for stop cock complete with C.I. surface box 100x100x75mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.

Constructing masonry Chamber 60X60X75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with channel lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design:

With F.P.S. bricks

Making connection of GI distribution branch with GI main of 50-80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :.

65 nominal bore

80 nominal bore

100 nominal bore

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

100 nominal bore

80 nominal bore

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required

100 mm dia, NB

150 mm dia, NB

Providing and fixing G.I. pipes complete with G.I. fittings including, trenching and refilling etc. external works

25mm nominal bore

80mm nominal bore

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality

25 mm dia, nominal bore

80mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : external works

25mm nominal bore

80mm nominal bore

Providing and filling sand of grading zone V or coarser grade all-round the G.I. pipes in external work.

25mm nominal bore

80mm nominal bore

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :

80 mm dia

Constructing masonry chamber 30x30x50 cm,inside with 75 class designation brick work in cement mortar 1:4 (1 cement:4 coarce sand) for stop cock complete with C.I. surface box 100x100x75mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.

Providing & fixing of Garden hydrant outlet consisting 1 No. 20mm dia. Ball valve, Bib cock (Brass) for connecting rubber hose, pipes & fittings including brick masonary chamber 300x300x500mm.

Providing and fixing brass bib cock of approved quality Bib Cock - 20mm

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : Ball Valve - 20mm

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :.

80 nominal bore

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

80 nominal bore

Raw Water Treatment Feed Pump set : - Providing, fixing, commissioing and testing package vertical raw water pumps, comprising of Electrical Driven inline pumping with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure guage bourden type, common suction and delivery header, bellows on sucton and delivery side complete in all repsects.

Pumps shall be suitable for 415 ± 10% volts 3 phase 50 Hz A.C supply & shall be having the following requirement complete with foundation and associated civil works.,, Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted)., Flow Prevention - Only Check Valve Suction & Delivery Header - SS 304 Suction & delivery header including all pipes, suction & delivery sides valves, NRV, Pressure gauges & accessories complete.

Flow Rate : 3.0 LPS (1 working + 1 stand by), Head : 35 M, Min. Motor HP : 3.0 H.P. (Each)

Water Booster Pumpset (Treated Water Supply) :- Supplying & supervision of testing & commissioning of Booster Pumpset (Hydropneumatic systems) as described below

Supplying & supervision of testing & commissioning of package vertical Hydropneumatic system, comprising of 2.0 nos. (1 duty + 1 stand by) Electrical Driven inline pumping sets each of 4.0 LPS to a head to 60 meter with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure switch, common suction and delivery header, bellows on sucton and delivery side complete in all repsects.

Pump mounted or wall mounted microprocessor based controller, Electronic control panel with frequency inverter, logic controller relays, pressure sensor, pressure sensor transmitter, electrical wiring, cabling from panel to pumps, level controller, two lined LCD display, diodes to indicate pump ready, pump running and fault capable to communicate with toher RS 485 interface. with Power box equipped with fuses or isolators or circuit breakers as required. complete with all accessories as per manufacturer specifications.

Suction & Delivery Header - SS 304, Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve, One Number Variable frequency Drive, Impeller : Stainless Steel, Shaft : Stainless Steel, RPM : 2900. Mover : Electric Motor, HP - As required., Necessary foundation with bolts, Ball valve on suction & delivery, NRV on delivery

Dust & veMetrein proof cubicle type motor control centre fabricated from powder coated 16 SWG MS sheet suitable to automatic working of above mentioned pumps.

Water Booster Pumpset (Roof Level ) Supplying & supervision of testing & commissioning of Booster Pumpset (Hydropneumatic systems) as described below

Supplying & supervision of testing & commissioning of package vertical Hydropneumatic system, comprising of 2.0 nos. (1 duty + 1 stand by) Electrical Driven inline pumping sets each of 2.0 LPS to a head to 25.0 meter with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure switch, common suction and delivery header, bellows on sucton and delivery side complete in all repsects.

Pump mounted or wall mounted microprocessor based controller, Electronic control panel with frequency inverter, logic controller relays, pressure sensor, pressure sensor transmitter, electrical wiring, cabling from panel to pumps, level controller, two lined LCD display, diodes to indicate pump ready, pump running and fault capable to communicate with toher RS 485 interface. with Power box equipped with fuses or isolators or circuit breakers as required. complete with all accessories as per manufacturer specifications.

Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve, One Number Variable frequency Drive, Impeller : Stainless Steel, Shaft : Stainless Steel, RPM : 2900. Mover : Electric Motor, HP - As required., Necessary foundation with bolts Ball valve on suction & delivery, NRV on delivery

Dust & veMetrein proof cubicle type motor control centre fabricated from powder coated 16 SWG MS sheet suitable to automatic working of above mentioned pumps.

Supply & Installation, testing and commissioning of centrifugal non clogging submersible sump pumps for plant room drainage. Pump capable capable of handling 25 mm dia soft solids. Motor suitable for 415 + 10% volts, 3 phase, 50 Hz AC Power supply. Pumps shall be suitable for automatic/manual operation (Overall depth of sump – 1.5 M). Submersible sump pump shall be provided with dry running protection. Inclusive of supporting arrangement for stationary type.

Two nos. of pump installed in one sump pit 1 working & 1 standby with automatic/manual opration as requireds.

Waste Water Drainage Sump Pump Flow rate : 4.0 LPS, Head : 22.5 Mtrs, Min. Motor HP : 2.2

Sewage Drainage Sump Pump, Flow rate : 4.0 LPS, Head : 22.5 Mtrs., Min. Motor HP : 2.2 (Each)

Supplying, storing, handling, installation, testing & commissioning of Vertical Dual Media Filter made out of MSEP/FRP composite Vessel complete suitable for test pressure of 7 Kg./cm2 with top and bottom dished ends, self supporting legs, manhole, hand hole, initial filling of Graded sand and gravels, pressure gauges, sampling cock, air vent, frontal MS/UPVC Piping, diaphragam valves for inlet, outlet, backwash inlet, backwash outlet drain etc.

Capacity : 3.0 LPS Working Pressure : (5 ± 2.5)MWC

Supplying, storing, handling, installation, testing & commissioning of Vertical Activated Carbon Filter made out of MSEP/FRP composite Vessel complete suitable for test pressure of 7 Kg./cm2 with top and bottom dished ends, self supporting legs, manhole, hand hole initial filling of Activated Carbon, pressure gauges, sampling cock, air vent, frontal MS/UPVC piping, diapharagam valves for intlet, outlet, backwash inlet, backwash outlet drain etc.

Capacity : 3.0 LPS Working Pressure : (5 ± 2.5)MWC

Supplying, storing, handling, installation, testing & commissioning of water softening system having MSEP/FRP pressure vessel suitable for test pressure of 7 Kg/cm2 including dished end, ion- exchange resin, Frontal piping, C.I. diaphragm type valve, brine injection assembly for regeneration of softener, brine measuring cum salt water tank, inter connected flexible polypropylene MS Rubber lined (MSRL) piping, valves including provision of bye-pass arrangement complete with inside and outside painting etc. as required.

Receiving, storing, handling and fixing of PVC/HDPE/FRP tank for Brine solution along with Hydraulic Injector with control valve and piping for brine injection. Capacity : 3.0 LPS Working Pressure : (5 ± 2.5)MWC

Capacity : 3.0 LPS , Working Pressure : (5 ± 2.5)MWC

Supplying and fixing of PVC/HDPE/FRP tank including electrical operated metering/dosing pump for dosing of alum/sodium hypo-chlorite solutions in pipeline (all contacting parts shall be of stainless steel). Capacity - 0-12 LPH

Supplying & fixing of float based visual flow meter (Rotameter) suitable for water flow rate of 10800 litres per hour in the input line of water softener including matching flanges, nuts, bolts and 3 mm thick rubber insertions/gaskets complete. to assess the water flow rate in water softener.

Providing & fixing stone slab table rubbed, edges rounded and polished of size 75 X 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size) as per Engineer-in-charge and finished smooth

White Agaria Marble Stone

Providing and fixing Salem Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required.

Kitchen sink with drain board 510X1040mm bowl depth 200mm.

Sink without drain board - 610X510 mm bowl depth 200mm.

Providing & fixing PVC waste pipe for sink oncluding PVC waste fitting Complete

Flexible Pipe - 32mm Dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm.

Providing and Fixing of vitreous china single trap syphonic pattern having back inlet, supporting chair wall hung water closet withflush valve and CP brass flush bend (European type) Wall Hung water closet with seat and lid, with C.P. brass hinges and rubber buffers, adapter, rubber joints fixed to W.C., C.P. brass screwed washers including cutting and making good the walls and floors wherever required and HDPE wc pan connector including jointing with white cement coomplete in all respects.

Providing and Fixing of low noise Concealed cistern 120 mm ; Dual Flush - 2 litre and 4 Litre (Concealed cistern without frame ) and 03 120 06 99 (Actualtion plate -Chrome finish)

Providing and fixing of ABS health spary which can tolerate water pressure up to 6 bar flow pressure with soecial durable rubber hose and holder in Polished Chrome , With Flow restrictor 6 lpm ; For green building requirement;

Providing and fixing of single-lever wash basin mixer ceramic having cartridge with hot water limiter including 2 flexible hoses Clean Fix S G 3/8 internal thread x 380 mm with flow volume 5 l/min independent of pressure flow pressure 0,5 - 8 bar.

Providing and fixing of design siphon(Bottle Trap), Housing and pipes out of polished brass, easy to install by means of plug-in connection of drainpipe Comprises: ABS rosette with slide ring, cleaning aperture with O-ring seal plastic plunger Use / Technical Data: design acc. to DIN 274 Material: brass chrome, PU 1 , W: 1.28 kg/pc.

Supplying & Fixing of CP soap dish Holder fixed to the wall with PVC rubber plug with CP brass screws.

Providing and fixing towel rail complete with brackets fixed with CP brass screws PVC sleeves etc. Complete

Providing and fixing of C.P. brass Showerhead with showerarm and escutcheon in polished chrome

Providing and fixing Towel ring with brackets fixed to wooden cleats with C.P. brass screws.

Providing and fixing C.P brass central hole Shower 3-in-1 Wall Mixer with Arrangement for Hand Shower & L Pipe for Overhead Shower complete in respects.

Providing and fixing of stainless steel braided flexible hoses with inliner EPDM Which can bear the maximum pressure of 10 bar and maximum temperature of 90 degree Celsius with bending radius of 25 r with length 500 mm with Union nut connection of 1/2"

Providing and fixing C.P. brass 15mm dia 2 in 1 Bib bib cock of approved quality confirming .

Providing and fixing C.P. brass Wall Mounted Sink Mixer J Pipe Spout

Providing and fixing of Regulating Angle valve with Comfort handle, with extended push rod, push rosette Ø 54 mm ; Material – Brass DIN EN / Noise Class I ; Connection: 1/2“/DN 15, Outlet: 1/2“/DN 15 ; Chrome / Weight 0.130 KG per piece .

Providing and fixing Toilet Paper Holder With Flap.

Providing and fixing soft white color vitreous China flat back, Rectangular wall mounted wash basin with R.S. or CI bracket and 32 mm dia outlet, with brass C.P. wall cap and extension pieces, 15 mm dia C.P. brass angle stop cock with 10mm dia C.P. brass connection pipe etc. CP brass chain, CP wall flange, rubber adopter for waste connection complete, CP brass chain CP waste and CP pipe to wall with CP wall flange and rubber adopter for waste connection complete, with pedestal of matching model below wash basin, including cutting and making good the walls wherever required.

Providing and fixing of Infrared sensor controlled tap With temperature controller ; battery operation with external battery compartment and 4x AA alkaline batteries including 2 flexible hoses G 3/8 int. thread x 450 mm with backflow preventer and prefilter and flow regulator ; flow volume: max. 3 l/min independent of pressure ; can be adjusted to 1.33 lpm (For LEED) with additional areator 28 931 00 99 ; flow pressure: 0,5 - 5 bar ,max. resting pressure 8 bar.

Providing and fixing soft white urinals with siphon and concealed C.I. brackets, brass C.P. supply and flushing connections with 1 N0. 15 mm Dia. Brass C.P. angle type stop cock with brass C.P. wall cap, with C.P. waste coupling with C.P. wall caps brass CP cones at inlet and outlets concealed lead pipes drains form bottle trap drain pipes in floor. Joining etc complete.

Providing and Fixing of low noise Urinal flush valve touch-free infrared flushing device Mains Operated 230 V / 50 Hz with internal isolating valve. Which includes roughing in set for electronic actuation and Urinal Control finishing set. Roughing in set should comprises - plastic construction casing with cleaning cover ; pre-assembled water path with isolating valve ; sealing plug ; cleaning cover ; with Flow pressure: 0,8 - 5 bar ; • flush volume: 0,3 l/s ; 230 V 50 Hz power supply unit with mains plug • fitting connection G 1/2" (DN 15) external thread; Connection: G 1/2" ext. thread/ DN 15, and Urinal Control finishing set should comprises mounting frame with electronic module ; front panel with sensor ; cartridge solenoid valve with pre-filer ; diagnostic lamps ; adjustment range; with technical data as flushing time: 2-15 s adjustable; vandal-proof design and Material: front cover out of ABS Plastic .

Providing and fixing Hand dryer with C.P brackets with C.P brass screws and PVC rawl plugs complete in all respects including cutting and making good the wall where required.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 1000x1000 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 1000x1000 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Glazed Vitrified tiles Matt/Antiskid finish of size of Tile 600 x 600 mm.

Providing and fixing Ist quality Vitrified wall tiles (For Guest & VIP Block) of approved make, in all colours, shades, of size 600x1200, as approved by the Architect, in dados and wall cladding, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and pointing in white cement mixed with pigment of matching shade complete (or jointing with grey cement slurry @ 3.3kg per sqm, including grouting of joints with epoxy grout of matching shade complete).

Stone work in Wave Pattern/ Geometric Design Pattern/ Abstract Pattern, Linear Pattern Straight Pattern as per Design/ Drawing. Machine cut, mirror/ diamond polish, Marble Combination stone work in Flooring, stones of different finished surface texture, laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/Sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified.

18 mm thick Italian Marble stone slab, Bottocino , Perlato,Rosso Verona, Fire Red or Dark Emperadore etc

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab, Bottocino , Perlato,Rosso Verona, Fire Red or Dark Emperadore etc

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye, Armani Green & Kandla grey Border or equivalent.

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.18 / 12 mm thick Grey arabico Marble stone slab or Equivalent

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick

Inlay work of floral motif or motif inspired by padi kollam by machine / manual for stone work in Wave Pattern/ Geometric Design Pattern/ Abstract Pattern, Linear Pattern Straight Pattern as per Design/ Drawing. Machine cut, mirror/ diamond polish, Marble Combination stone work in Flooring and steps etc., stones of different finished surface texture, laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Architect/ Engineer-in-Charge. (The cost of protecting stone work with polythin and a layer of POP or by any other mean as required to be included in the quoted price of this item)

18 mm thick Italian, Marble stone slab,of any kind. Stone to be approved by Architect/ Engineer/Owner

Providing and laying of 6mm thick PVC Vinyl flooring including foam backing, vinyl floor covering of size minimum1200 mm width x 6 meters length of weight 4400 g/m2 with wear layer thickness of 1 mm. Wear layer should be treated with Protocol (UV cured Polyurethane surface treatment) which facilitates ease of maintenance and eliminates the use of acrylic emulsions. Residual indentation should be less than 0.25mm & should conform to EN ISO 24343-1(EN 433). The product should have antibacterial properties. The product should also fulfill dimensional stability(EN ISO 23999(EN 434) & effect of furniture leg(EN 424). It should also be suitable for underfloor heating. The product should have excellent sound absorption of 24 db and excellent shock absorbent behavior. The laid flooring shall confirm the fire rating Cfl-S1 class as per EN 13501-1.

Providing and laying at site 10-13mm thick engineered wood flooring with specially developed core: having patented click system perfect fold joints to secure long lasting joint. The planks shall be placed on an under lay of 0.2mm thick alkali resistant polyethylene sheet. All as per manufacturer specification. (The cost of protecting Wooden Flooring work with polythin and a layer of POP or by any other mean as required to be included in the quoted price of this item).

Providing and fixing at site 10mm to 13mm thick 100mm high laminated wooden skirting/trim all complete as engineer in charge.

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Entry Mat System Providing & Fixing entrance matting (Heavy Duty) with enhanced absorption. Construction - Looped pile carpet design with solid vinyl backing. Material - Polypropylene & Nylon with vinyl backing. Size - Standard/ as per site in charge.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent Quartzite Flooring

Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately).

White sand stone - 30mm thick gang saw cut stone

Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately).

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias, skerting,dedo and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye, Armani Green & Kandla grey Border or equivalent.Quartzite Flooring

Area of slab upto 0.50 sqm.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Marble Work

Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra For Providing-V- Groove of Size 6 x 6 mm in Stone Wall Lining at all levels as per architect drawing.

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Second class teak wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) : - 35 mm thick shutters - Second class teak wood.

Second class teak wood - 35 mm thick shutters

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

2nd class teak wood 50 x 20 mm

Supply and fixing of pull Handle back to back with 305mm CTC, adjustable fixing for glass, wood and metal doors in brass finish. The pull handles should have supporting washer with raised beveling on the outer surface. Length = 350mm.

Providing and fixing antique finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing Antique bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing Antique bright finished brass tower bolts (barrel type) 300x12 with necessary screws etc. complete :

Providing and fixing of Antique brass door buffer with magnetic catcher.

Providing and fixing overhead cam action door closer with adjustable closing force EN2-4.all as per specifications.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 50 kg and door width upto 1000 mm), with necessary accessories and screws etc. complete.

Providing and fixing Teak Wood motif fixed over door paneling with approved detail and approved size as per drawing and as per direction of Engineer -in-charge.

Second Class Teakwood handrail approx 900mm high togeather with 75mm dia decorative curved teakwood post apoxy grouted to tread with 12mm dia S.S rod in sleeve embedded in RCC at approx third tread infilled with 12mm thick teakwood jalli of specified patteren fixed in between baluster, 40x6mm SS plate screwed to teak wood blauster to receive 85x65mm teak wood curved hand rail with and including polishing of teakwood hand rail.All work complete as shown in drawing.

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Casement window single panel with S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 0.75 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc.

Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately).

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.)

Providing & Applying weather proof sealant on outer joints of approved make confirming to IS & directed by Engineer-in-charge - Sealant 25mmx10mm at joints.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc.

Sal wood

Supply and installation toilet cubicles of width and depth as per specifications/ site drawings. Cubicle height to be 2105 mm. Made from solid grade compact high pressure laminate as per IS:2046 manufactured under high specific pressure > 5 MPa with bunch of Kraft papers impregnated with thermosetting phenolic resin and decorative papers impregnated with thermosetting melamine resin which provide superior scratch, abrasion, heat, chemical, impact, graffiti & moisture resistance along with anti-bacterial properties. Top Head frame fixed to the wall on both sides using MS- wall brackets. The pilaster is slotted & affixed to the top head frame and secured from the top leaving all clear gap of 150mm and without any support from the bottom. The intermediate panel shall be anchored to the wall and pilasters.

Panel thickness 12 mm. Design no. as specified by Arch. in suede finish. Size of panels to be as per drawing. (The cost of protecting Tile work with polythin and a layer of POP or by any other mean as required to be included in the quoted price of this item)

HARDWARE & ACCESSORIES AND OHER DETAILS: • H shaped (Top) head frame structure made of extruded Aluminium grade 6063 T5-50 micron epoxy powder coated for surface protection. Size to be 125x70x5T. Corner joinery section, Size to be 40x16.5x1.8T. U-Channel Wall joinery section, Size to be 22x16x1.6T. Door stopper section, Size to be 21x12.5x1.6T. • Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be matt type. Covers to be lacquer coated. Cubicles- Standard Sizes (W x D x H)- 900 mm x 1550 mm x 2105 mm, (Height is including 150 mm gap from bottom) with one Door Size- 600 mm • Conical shape Coat hook with rubber stopper made from Stainless steel grade 304. Surface finish to be matt type/ as per Architect • Round Door knob diameter 30 mm with grooves for better hand grip made from Stainless steel grade 304. Surface finish to be matt type. • Rotating Thumb-turn locking system with privacy indicator made from Stainless steel grade 304. Surface finish to be matt type/as per Architect. • Stainless steel grade 304 screws. • Anti-rotation Nylon polyamide grade-6 expandable wall plugs. • The cubicle to be fixed as per drawing layout and shall be completed as per drawing.

Supply, fixing and Installation of Slim Line Modular Aluminium Fixed partitioning frame of 100-105 mm x 25-30 mm which can accommodate 2 panels of glass of 10 mm thickness separated by 40-50 mm distance for better sound insulation and acoustic properties. The rate to include Design, Fabrication, Supply, Installation & Handover of slim line fixed partition system. the fixed partition system should accommodate openable door on Hinges, along with providing and fixing of 10mm thick toughened glass in frames as per approved drawings/ instruction of the Architect. Door to be paid seperately.The system of fixed partition with openable door to be custom designed to with stand the design confirming to IS -875 part III. The system shall have two barrier gasket system to hold glasses . Microwave cured EPDM gaskets to accommodate glass thickness as per structural requirement, weather sealants, SS 310 grade screws of approved make, all in complete required to perform as per specification and drawing in conjunction with BOQ. Complete system shall be warranted for minimum 10 yr. against design & workmanship defects.

The extruded aluminium sections of Alloy 6063 T5 / T6 & tolerances confirming to DIN / EN standard, of approved architectural sizes , from approved extruder. The structural profiles shall have minimum 1 to 1.6mm wall thickness. All the internal visible surfaces shall have high Durability) / Super durable (Jotun) Powder coating of 60 - 80 micron confirming to ASTM E 283, ASTM E 331, ASTM E 330AAMA 2604 or anodizing shade as approved by Architect with minimum 25 micron The non visible aluminium surfaces shall have minimum chromatizing treatment.

Material shall be as per make list in tender document.. All shade approval shall be as per Architect's Approval. The system shall demonstrate performance for air seal / water seal / structural requirement . The system performance test shall be mandatory. The performance test shall be carried out at an accredited laboratory having fully atomized data acquisition system with provision to capture all values in the test results sheet . The sequence of test and standard shall be ASTM E 283, ASTM E 331, ASTM E 330 , AAMA 501.1. Sequence of testing and criteria shall be as per tender Specification. The quote rate shall include all design, engineering & shop drawing approval from architect. Glass : 10 mm clear Heat strengthened/ TOUGHENED Glass Tolerance of 5 mm allowed in both dimension of the cross section of the slim line partition as per manufacturers specification.

Providing and fixing non load bearing fixed frame for fire resistant glazed Partition for 120 minutes Fire Rating, made out to a profile of dimension 60mm x 70 mm of 1.6 mm thick galvanised steel sheet as per test evidence suitable for fixing fire rated glass for 120 minutes of both integrity & radiation control (EW120) & minimum 20 minutes of insulation (EI20).The profile has to be fixed to the supporting construction by means of anchor fasteners of size M10 x 80, every 150 mm from the edges and every 500 mm (approx) c/c. Linear measurement of frame shall be measured for payment. The frame shall be filled with mineral wool insulation of density min 96kg/ m³. and finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per NBC 2016, IS 16231 (Part 3):2016 and directions of Engineer - in- charge.

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing 600 mm deep pantry cabinet below counter wooden cupboards shutters with teak wood shutter 20mm thick shutter fixed to cabinet by means of necessary brass fittings such as hinges tower bolt ball catcher handle etc. complete including 19 mm thick vertical/ horizontal partitions of commercial ply board with drawer unit with guide rail including locking arrangement and knobs heavy duty ss hanger rail etc. painting of wooden members with two or more coats of synthetic enamel paint of approved make in the inner side and shade over over a coat of primer complete and melamine polish on the outer surface as per architects design and drawings. All surfaces to be covered with laminate 1mm thick. All drawers to have necessary stainless steel, grills, jaalis, utensil holder and other stainless steel accessories of reputed brand.

Providing and fixing 450 mm deep pantry cabinet above counter wooden cupboards shutters with teak wood shutter 20mm thick shutter fixed to cabinet by means of necessary brass fittings such as hinges tower bolt ball catcher handle etc. complete including 19 mm thick vertical/ horizontal partitions of commercial ply board with drawer unit with guide rail including locking arrangement and knobs heavy duty SS hanger rail ext. painting of wooden members with two or more coats of synthetic enamel paint of approved make in the inner side and shade over over a coat of primer complete and melamine polish on the outer surface as per Architect's design and drawings.

Solid block wood work for architectural and design aesthetics on all floors of the building. Solid wood large sections to be used for making cornices and mouldings on all floors at the junction of ceiling and vertical wall as per design and drawing. Architectural solid wood section work for ceilings frames of size 150x100 on all floors ceiling. Solid wood work for wooden artifacts, murals and motifs as per design and drawing. All solid works may required lathe work on wood chiseling work on solid wood and machine/manual work on solid wood for al architectural work as per drawing design and directions.

Second class teak wood

Standard silver anodized operator profile electromechanical lock with 12 mm plain toughened frameless glass for complete elevation - 2 moving panels. UPS of 750 VA shall be provided by others, which will give power backup of 20 min. Only & if the duration of power cut to the operator is more than 30 min., then separate arrangement needs to be done for the same as automatic operator requires uninterrupted stabilized power supply. it should include Wall Corner Protection. (WCP) The above work complete in all respect as per approved drawings and to the satisfaction of Architect.

Providing and fixing 12 mm thick frameless toughened glass door shutter with glass of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Architect (Cost includes providing & fixing of Door handle, lock . top patch , bottom patch , Floor Spring Top and bottom pivot and stopper).(one set of hardware for one door. payment in Sqm of door size. minimum width of door 0.9 mtr).

Solid block wood work for architectural and design aesthetics on all floors of the building. Solid wood large sections to be used for erecting Pergola & Gazebo including all necessary items and as per design and drawing. Architectural solid wood should be coated with weather-proof paint. All solid works may required lathe work on wood chiseling work on solid wood and machine/manual work on solid wood for al architectural work as per drawing design and directions.

Durable Treated Wood

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

80x1.25 mm M.S. laths with 1.25 mm thick top cover.

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters.

Exceeding 10.00 sqm and upto 16.80 sqm in the area.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion - Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Designing the Semi Unitised Structural Glazing System as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the Particular specification (Methodology should be got approved by the dept officials). Design the framing system (ie.Male & Female frame) to support Vision panels, Spandral panels either with Glass or Aluminium composite panel, openable window panels on a continuous framing supported between floors. Also design the split framing unitised glazing system in case of Strip or Punched windows with vision panel proposed with either Insulated / Monolithic Glass. Groove width in the system both in horizontal and vertical shall not be more than 20mm.Glazing of panel shall be done only at factory at the controlled atmosphere. Vertical in-situ glazing shall not be carried out during construction / erection stage.

I. DESIGN:

a. Design: Design pre-assembled aluminium semi Unitised Structurally glazed Panel / strip / punched window system to any shape and profile to with stand a design wind pressure (Test pressure shall be 1.5 times of the design wind pressure) conforming to IS 875 - Part-3 and Lateral forces as per IS 1893 (Latest Revision) and fixed at horizontally / vertically / sloped / curved position etc as shown in the drawing by using Aluminium extrusion, Glass, Spacer tape, Gasket and Sealant as specified. System shall be designed with Air Pressure equalization chamber and concealed continuous gutter vertically and horizontally at all levels as self drainage barrier to achieve water tightness besides providing EPDM Gaskets as air & water barrier.

b.System: System shall be designed to withstand a design wind pressure specified above with self-bearing modular elements supported between floors, EPDM Gaskets to prevent the system from Air & water penetration , double adhesive spacer tape, backer rod, sealant, supporting brackets (Resistance to design wind pressure), Seperator Gaskets for Bi-Metallic Corrosion, Pressure equilization chamber in the system, built-in continuous internal drainage gutter for collection and facility at lowest floor level to drain out penetrated water, in built adjustability to accomodate thermal expansion,thermal movement and movement due to any other forces. System shall be designed with open groove joint system and the aluminium member and Sealant shall not be visible on the external surface except colour anodised aluminium holder to the required width and thickness as per design at bottom of panel as Dead load support to the Glass panel.

c. Movement : System shall be designed to accommodate movement due to any force including the movement resulting from the exterior skin temperature ranging from 15 to 85 deg.celsius, Interior skin temperature ranging from 15 to 30 deg.celsius, and also to accommodate the horizontal building movement of 10 mm per panel & vertical movement of 20 mm between floors on the aluminium framing system with support brackets, glass, gaskets and fastening devices. System shall be designed to accommodate the size and shape of the glass panels as per the approved drawings including approved modifications as may be required during execution as well as all other incidental forces and stresses likely to be experienced under service conditions, i.e. Lateral force, Dead weight and Thermal expansion due to building movement both vertical & horizontal etc.

II. MATERIALS:

a.Frames: Providing and fixing pre-assembled aluminium frame work (Main & child frame) designed to with stand design wind pressure and movements as specified as continuous framing system for Structurally glazed panel and split framing system for structurally glazed punched windows. Horizontals (Transom) shall be made out of specially designed extruded sections matching to the Mullion depth in such a way the Mullion and Transom flush on inside of the facade. Fabricated Mullion and Transom shall be fixed at all levels and heights as per approved shop drawing into masonry wall / RCC surface with supporting system consisting of Brackets / Clamps, fastening straps, nuts, bolts, rivets, washers and other fastening materials. Extruded section shall be designed to accomodate Insulated Glass (DGU) / Monolithic (Single) Glass and Aluminium composite panel as per the approved shop drawings. Extruded sections shall be 22843 & 22739 (H9) grade conforming to BS 4174 or IS 8147, finished with AC15 grade Architectural quality electrolytic colour anodic coating of approved colour - IS 1868.

b.Glass: Providing and fixing Insulated Glass (DGU) - 24 mm thick (6mm ST 767 or 750 Toughened glass - as approved by the Departmental officers +12mm air + 6mm clear toughened glass) / Monolithic (single) Glass - 6 mm as per specification below for both vision and spandrel panel conforming to the minimum spectral parameters as specified. Spacer for Insulated glazing unit shall be aluminium extruded profile and finished with AC 15 grade electrolytic colour anodic coating of black colour conforming to IS 1868 and filled with dry desiccant. Primary sealant shall be Poly-isobutylene (PIB) and Secondary seal shall be structural silicon sealant of DC 995 (one part) or DC 983 (two part) of Dow corning or approved equivalent. Make and thickness of Inner pane glass shall be the same as outer pane glass of DG unit.

c. Processing of Glass : Details of the processor and their facilities should be submitted to the Employer/PMC/Architect for approval. Insulated glazing unit shall be processed only by the approved Processor. All glass panes used in the glazing shall be heat strengthened conforming to ASTM C 1048. No tong marks shall be allowed in the processed glass. Necessary test certificate shall be produced by the processor to confirm the adherence of the parameters set out in the codes and standards. New substrate glass shall only be used for coating and to ensure the same, a certificate shall be produced by the contractor. Necessary clearance from the processor shall be arranged by the contractor for the inspection of Employer/PMC/Architect of the glass processing plant during the progress of glass processing.

d.Gaskets: Providing and Fixing Ethylene Propylene Divine Monomer (EPDM) Gaskets as weather strip and barrier at minimum 3 stages to ensure water and air tightness. Weather strip shall be EPDM Gaskets with shore 61/71 Grade of Sai rubber make or Osaka rubber make or approved equivalent. Necessary test certificate shall be produced by the Contractor.

e.Sealing: Providing and applying the structural sealent for the glazing at factory confirming to the thickness & bite of sealants as designed & determined by calculation, verified and tested by Manufacture's of sealant. Bite and thickness shall be designed to withstand 3 times of the stress caused by the design wind pressure and the Design calculation of sealant manufacturer shall be produced along with shop drawing for approval.Supplying and fixing the Double Adhesive spacer tapes for glazing the panel at factory shall be open cell polyethlene and it shall be approved tape equivalant. Jointing / Sealing shall be done with Non structural (weather) sealant / Non staining sealent of DC 789 HP of Dowcorning make or approved equivalant with Polyurethene baker rods of Supreme make or approved equivalant. Acetoxy sealent shall not be used for Structural Glazing application. In general, the type of sealant shall be as follows:

Shop / Factory Sealants : i) Structural sealant shall be DC 995 (one part) ii) Non-Structural (weather) sealant shall be DC 789 HP of Dow corning make(one part) or approved equivalent. Colour - Grey or Black colourii) Non-Structural (weather) sealant shall be DC 789 HP of Dow corning make(one part) or approved equivalent. Colour - Grey or Black colour

Field Sealants : i) Structural Sealant shall be DC 789 (one part) or DC 995 (one part) of Dow corning make or approved equivalent. ii) Non-Structural (weather) sealant shall be DC 789 HP of Dow corning make or approved equivalent. Colour - Grey or Black colour iii) Structural anad non structrual sealent (weather) sealant dow corning or approved equivalent Colour - Grey or Black colour

i.Top Hung windows: Providing and fixing the shutter with Multi point locking handle without key - Model no 610 KH at centre of the transom having a size of 110 x 27mm of Aluhalpha make or approved equivalant and shall made out of aluminium die cast with powder coat finish - 65 microns, matching to the transom profile colour. Rate shall include the shutter frame as designed, EPDM gaskets, all hardwares like hinge, stay and handle with key, fastening materials, all other necessary materials etc.

j.Off-Site proto type Test: Provide shop drawings and design calculation to carry out the full Scale off site proto type at an approved Laboratary in india based on the Design Criteria set out in the Technical specification and confirming to ASTM E 330. Methodology along with shop drawing shall be submitted for the approval of Employer/PMC/Architect.

Conduct full scale off-site proto type test as per design creteria set out in the Technical specification and confirming to the standards as per ASTM E 330. Necessary clearence from the Laboratary to inspct the test and the contaractor shall arrange for the inspection of Employer/PMC/Architect to witness the test during the test is in progress including the expenses incurred for the Inspection of the team. If off-site proto type test fails, correct the defects revealed to the satisfaction of the performance data as set out in the Technical Specification with prior approval of Employer/PMC/Architect on defects rectification Methodology. Upon approval of methodology retesting shall be done at laboratory to the satisfaction of the performance data as set out in the Technical Specification with prior approval of Employer/PMC/Architect. Any charges on account of rectification of test specimen and test rig due to failure of the test shall not be paid for.

Semi Unitized Structural glazing system and Associated works : Quote rate for complete system as mentioned above for the items covered below including glass fixing, INCLUDING cost of glass, etc.,

Note : The following perfomaance test are to be conducted on sstructural glazing system if areaa of structural glaazingg exceeds 2500 sqm from the certified llaborattories accrediated by NABL (National Accrediation Board for Testing and Calibration Laboratories), Department of Science & Technologies India.. Cost of testting is payable separately. The NIIT approving authority will decide the necessory of testing on the basis of cost of the work, cost of the test and importance of the work. Performance TTesting of Structural glazing system tests tto be conducted in the NBL Certifies laboratories. 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200mVhr. 2. Stataic Water Penetration Test. (50pa to 1500pa) as per AStTME-331-09 testing method for a range upto 2000ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAAMA 501.01- 05 testingg method for a range uptto 2000ml. 4. Structuraal Performaance Deflection and deformation by static air pressure test (1.5 times desing winf pressure without any failure) as per ASTME-330-10 testing method for the raange upto 50mm. 5. Selsmic Movement Test (upto 30mm) as pere AAMA 501.4-09 testing method for Qualitative test Tests to be condducctedd on ssite. 6. Onsite Test for Water leakagge for aa pressure range 50kpa to 240kpa (35psi) uptto 2000 ml.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses,frames etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses,frames etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval,

including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks).

12.5 mm thick tapered edge gypsum moisture resistant board.

Providing and fixing Gl Clip in Metal Ceiling System (wooden Finish) of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with :

GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

true ceiling officially approved anchor fasteners maximum at 1200mm Centres as per the requirements of DIN EN 13964 and the statics of the system. Ensure horizontal and flush alignment during installation. All ceiling shall be TAIM Certified: For LEED certification by Indian Green Building council (IGBC). The system will meet Fire retardant standard of BS 476: Part 6 & Part 7

Supply and installation of Wooden Veneer Ceiling made of MS Frame in size 40mm*40mm (18guage) on mount with MS plate & fastener with the true ceiling. 12mm ply place on frame in century brand 1mm Veneer Sheet paste with ply in Century brand Melamine matt finish polish perform on veneer surface with the spray gun.

Supply & installation of MP3 /approved equivalent , fiber board core,Melamine laminated finish, perforated wooden panels with 3mm perforations at 16mm pitch, backlined with black acoustical fleece, square edge, of size 600x2400x16mm,having density 800Kg /m3, weight 9.6Kgs/m2 which is suspended by using 0.3mm thick and 24mm wide pre coated metal T24 grid system.

The T24 Grid system shall include providing and fixing wall angle(WA24W30) with equal flanges of size 24mm wide, length 3000mm, 0.4mm thick fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the MainT24(MT24W36) having flange width 24mm, height 38mm, length 3600mm from the soffit with help of soffit cleat and wire rod with leveling spring clip at 600mm c/c . Spacer bar with pre notched slots (wall angle with equal flanges of size 24mm wide, length 3000mm, 0.4mm thick) at 600mm centers in staggered pattern are placed above main T24 to hold system in position. Spots MP conceil edge of size 600x2400x16mm shall be slided into the grid.

Technical Parameters • Core - fibreboard • Fire – 1 • Acoustics – NRC upto 0.55 • Climate (OC RH) – 40, 70 • Termite resistance – Yes • Light reflectance – Colour dependent • Green (RC %) – 25 • Hygiene (VoC, Clean room) – Low, Class 1

Supply and installation of Open cell ceiling Armstrong make 25mm GI Channel with butterfly hanging with 6mm hilti fastener and 100mm with powder coated in aluminum material.

TRADITIONAL DESIGN STAINED GLASS CEILING

Providing 10 mm thick Plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately):

Flat surfaces

Curved surfaces

Providing and fixing Teakwood false ceiling at in double height including providing and fixing of composite frame work made of 50x50 mm hardwood and 25x50 mm MS hollow tube, with primer coat, at 600 mm centre to centre, including fixing and finishing of solid teakwood to ceiling framework. The teakwood ceiling to have designer mouldings and motifs, created through CNC router and lathe machine and also including the cost of making openings for light fittings, grills, diffusers, cutouts , all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of treatment and polishing.

Flat surfaces

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

6mm cement plaster

1:3 (1cement: 3 fine sand)

20mm cement plaster

1:3 (1cement: 3 coarse sand)

15mm cement plaster

1:4 (1cement: 4 fine sand)

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Upto 13m Height

13m to 16m Height

16m to 19m Height

19m to 22m Height

22m to 25m Height

Providing & fixing Chicken wire mesh on joints of RCC & Brick work before plastering complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer. Quote for each layer over the plastered wall surface to prepare the surface even and smooth complete.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Finishing walls with interior texture paint of required shade :

New work (Two or more coats applied) over and including priming coat of interior grade primer.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.

New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Painting with oil type wood preservative of approved brand and manufacture :

New work (two or more coats)

Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant.

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Painting with aluminium paint of approved brand and manufacture to give an even shade . Two or more coats on new work

Supply & Installation of Fiberboard core plain, unperforated panels, veneer laminated finish, tongue-groove edge 1200x600x12mm thk - Wall Paneling- Supply and Installation of Fiberboard core plain, unperforated panels, veneer laminated finish, square edge, FR Grade of size 1200x600x12mm having density 750Kgs/ m3, weight 12 kg/m2 installed by using GI framework and Z-bars.

The GI strut work includes Cross channel having thickness 0.45mm, length 3600mm, knurled web 40, depth 10mm and equal flanges 15mm is fastened to wall positioned vertically at 600mm centers. GI Z bars having 40mm height, thickness 1.2mm is first fixed behind the panels by using suitable fasteners @ 500mm c/c.Another length of GI Z-Bars are then installed over Strut cross channel horizontally so as to match spacing with Z-bars installed behind panels Panels are then slided into the Z bars fixed on cross channel. Long edged of panels should be perpendicular to Z-bars.

Technical Parameters • Core - Fiberboard • Fire – Class 1 & P • Acoustics – NRC 0.25 • Climate (OC RH) – 50, 70 • Termite resistance – Yes • Light reflectance – Colour dependent • Green (RC %) – 25 • Hygiene (VoC, Clean room) – Low, Class 3 • Strength, Load capacity (Kg) - Antisag

Supply & Installation of Cushion wall paneling with premium quality of fabric with fibre cotton over BWP plywood. Fabric, design & pattren approved by Engineer-in-Incharge. Cost of frame and plywood paid in respective item.

Providing and fixing of 4 mm thick annealed SGG Planilaque Evolution (premium GRIHA rated lacquered glass from Saint-Gobain) of approved color by Architect/ Client, fixed with SGG Ultrafix or equivalent (compatible neutral core silicon / double sided tape) on a perfectly leveled 12mm thick water proof marine plywood with bevelling and polishing which is mounted on the RCC wall/any other structure ,base structure to be provided by client including ply. Lacquered glass must be made industrially (via curtain coating process); opaque (if viewed against a support wall), coated with PU lacquer (60 micron thick); color consistency (measured by Minolta spectrophotometer CM5081); highly durable (passes PERSOZ hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999); environmentally friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial / 6% post consumer); compressive strenght (1000 MPa) & tensile strenght (40 MPa),same as float glass;

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). 6 mm thick Cement bonded wood particle board as per IS:14276

Providing and fixing Pre -laminated medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately). Pre-laminated with decorative lamination on both side exterior Grade - I MDF Board 12 mm thick confirming to IS:14587.

Providing and fixing of Wooden Wall panelling made of 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 finished fixed over the MS frame with 40 x 25 x 2.0 hollow section at the spacing of 600mm c/c. The wall panelling shall be finished with one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with Decorative veneer facings of approved manufacture and shall be finished with melamine polish of approved shade etc complete.

Providing and fixing 6 mm thick mirror of superior glass (of approved quality) and of required shape and size with frame of 6mm thick acrylic over 12mm thick BWP Ply. 12mm thick acrylic and BWP ply to be paid separately in their respective items.

Providing and fixing in position 12mm thick bitumen impregnated fiber board conforming to IS: 1838, including cost of primer, sealing compound Grade-A in expansion joints.

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal

aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier

Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall confirm to ASTM 6063). Floor Joint of 100 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the

Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063). Wall Joint of 100 mm gap

Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints.

200 mm wide

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile

that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists

damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063). Roof Joint of 100 mm gap.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .

The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

Providing and fixing Scaffolding net of required width made of high density Polyethylene UV stabilized knitted on warp knitting machines having density 100grams/sqm and shading coefficient minimum 75% around the construction site/ for vertical extension as per requirement including fastening/tying with building/scaffolding pipes or with any other fixtures etc. complete as per direction of Engineer-in-Charge. (One time payment shall be made for providing Scaffolding net from start of work till completion of work including shifting if any. The Scaffolding net shall be the property of the contractor on completion of the work)

Providing and fixing stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc. White sand stone.

Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size underdeck on ceiling surface, complying with ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of > 350 kPa listed as per ASTM D 1621, density of 34-36 kg/cum as per ASTM D 1622, water absorptions ? 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1 listed as per ASTM D 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576. Fire retardent property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 class A, fixed with suitable water based adhesive and fastener, complete in all respect as per the direction of Engineer-in-Charge.

Supply and fixing of prefabricated GI trap doors of size 900 mm x 600 mm x 18mm of to be recessed in ceilings wherever required.

Providing and fixing of Fire Hose Cabinet made of angle iron (40 mm x 40 mm x 5 mm) MS door frame 900x2100 door capable of accommodating fire hose reel, landing valve, hose pipes, fittings & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) Cost of fire extinguishers not included in item rate. (Liasioing with civil contractor for making 900x600x2100 Recessed type mansoary box (by civil contractor).

Providing and fixing of TAC approved 1.6mm thick M.S. fire hose cabinet (750x600x250mm) made out of 16 gauge M.S. sheet capable of accommodating landing valve, hose pipes, fittings & accessories. The box shall have a front glass door with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) - for external and roof hydrant.

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Single headed Gunmetal

Supplying and fixing first-aid Hose Reel with MS Construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20mm nominal internal dia water hose thermoplastic (textile reinforced) type- 2 as per IS: 12585 20 mm nominal internal dia gun netal globe value & nozzie. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. - 30m length

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun Metal

Gun Metal

Providing and fixing of Fire Axe

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing and fixing C.I. double acting air valves of approved quality with bolts, nuts, rubber insertions etc. complete ( The tail pieces, tapers etc. if reqd. will be paid separately) - 50mm dia

50 mm dia.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150mm dia

150 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

80 mm dia

100 mm dia

150 mm dia

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing and fixing brass ball valve with SS 304 Stem and ball, teflon seat complete (PN-16).

25mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

150 mm nominal bore (class C)

100 mm nominal bore (class C)

80 mm nominal bore (class C)

65 mm nominal bore (class C)

50 mm nominal bore (class C)

40 mm nominal bore (class C)

32 mm nominal bore (class C)

25 mm nominal bore (class C)

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

150mm dia

100mm dia

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing, fixing, testing & commissioning of 15mm dia uartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Horizontal side wall sprinkler

Pendent /Upright type

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. - 1200mm

Providing and fixing carbon-di-oxide type fire extinguishers consisting of welded M.S. cylindrical body, internal discharge tube, discharge nozzle, suspension bracket, conforming to IS 15683, finished externally with red enamel paint and fixed to wall with brackets complete with internal charges. - 4.5 kg capacity

Providing and fixing (ABC Dry Chemical Powder ) type Fire Extinguisher of Capacity 6 kg Confirms to IS 15683, bearing ISI mark complete with brass forged squeeze grip type valve fitted with pressure gauge , pressurize with dry Nitrogen gas filled, with discharge nozzle with wall mounting bracket complete with internal charges - Capacity 6 Kg.

SITC of LIFT PANEL1 having the following specifications:- IP Rating : IP 42 Incomer 1 No. 125 A 25 KA, 4P MCCB Incomer Metering & Indication: 415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

1 No. Digital VAF + PF Meter (110V) (With RS 485 Port)

Bus bars

150A, TPN Aluminium Bus bars of electrolytic grade with heat shrinkable sleeve 25 KA.

Outgoings

1 Nos. 63A 10KA, 4P, MCB's, (LIFT PANEL 1)

1 Nos. 63A 10KA, 4P, MCB's, (LIFT PANEL 2)

1 Nos. 63A 10KA, 4P, MCB's, (MACHINE ROOM DB)

1 Nos. 63A 10KA, 4P, MCB's, (SPARE)

Lift Panel as described above.

SITC of LIFT PANEL2 having the following specifications:-

IP Rating : IP 42

Incomer

1 No. 125 A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

1 No. Digital VAF + PF Meter (110V) (With RS 485 Port)

Bus bars

150A, TPN Aluminium Bus bars of electrolytic grade with heat shrinkable sleeve 25 KA.

Outgoings

1 Nos. 63A 10KA, 4P, MCB's, (LIFT PANEL 1)

1 Nos. 63A 10KA, 4P, MCB's, (LIFT PANEL 2)

1 Nos. 63A 10KA, 4P, MCB's, (MACHINE ROOM DB)

1 Nos. 63A 10KA, 4P, MCB's, (SPARE)

Lift Panel as described above.

SITC of Electrical Panel for Ground Floor having the following specifications:-

IP Rating : IP 42

Incomer

1 No. 100A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

1 Nos. 63A, 4P MCCB's - (Kitchen VTPN DB)

1 Nos. 40A, 4P MCB's - (DB 1)

1 Nos.32A, DP MCB's - (DB 2)

1 Nos. 40A, 4P MCB's - (HVAC AHU PANEL MCC 01)

1 Nos. 32A, 4P MCB's - (HVAC AHU PANEL MCC 02)

2 Nos. 40A, 4P MCB's - (SPARE)

Panel as described above.

SITC of Electrical Panel for First Floor having the following specifications:-

IP Rating : IP 42

Incomer

1 No. 100A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

7 Nos. 32A, DP MCB's - (ROOMS DBs )

1 Nos. 32A, DP MCB's - (C.A. DB)

1 Nos. 40A, 4P MCB's - (HVAC AHU PANEL MCC 01)

2 Nos. 32A, DP MCB's - (SPARE)

Panel as described above.

SITC of Electrical Panel for 2nd Floor having the following specifications:-

IP Rating : IP 42

Incomer

1 No. 100A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

6 Nos. 32A, DP MCB's - (ROOMS DBs )

1 Nos. 40A, 4P MCB's - (HVAC AHU PANEL MCC 01)

2 Nos. 40A, DP MCB's - (SPARE)

1 Nos. 32A, 4P MCB's - (SPARE)

Panel as described above.

SITC of Electrical Panel for 3rd Floor having the following specifications:-

IP Rating : IP 42

Incomer

1 No. 100A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

10 Nos. 32A, DP MCB's - (ROOMS DBs )

1 Nos. 40A, 4P MCB's - (HVAC AHU PANEL MCC 01)

2 Nos. 40A, DP MCB's - (SPARE)

1 Nos. 32A, 4P MCB's - (SPARE)

Panel as described above.

SITC of Electrical Panel for 4th Floor having the following specifications:-

IP Rating : IP 42

Incomer

1 No. 160A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

200 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

7 Nos. 32A, DP MCB's - (ROOMS DBs )

1 Nos. 32A, DP MCB's - (C.A. DB)

1 Nos. 40A, 4P MCB's - (HVAC AHU PANEL MCC 01)

1 Nos. 63A, 4P MCB's - (ZYM DB )

2 Nos. 40A, DP MCB's - (SPARE)

1 Nos. 32A, 4P MCB's - (SPARE)

Panel as described above.

SITC of Electrical Panel for 5th Floor having the following specifications:-

IP Rating : IP 42

Incomer

1 No. 100A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

10 Nos. 32A, DP MCB's - (ROOMS DBs )

1 Nos. 40A, 4P MCB's - (HVAC AHU PANEL MCC 01)

2 Nos. 40A, DP MCB's - (SPARE)

1 Nos. 32A, 4P MCB's - (SPARE)

Panel as described above.

SITC of Electrical Panel for 6th Floor having the following specifications:-

IP Rating : IP 42

Incomer

1 No. 100A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

1 Nos. 63A, 4P MCB's - (DB 1)

1 Nos. 40A, DP MCB's - (DB 2)

1 Nos. 40A, DP MCB's - (DB 3)

1 Nos. 40A, 4P MCB's - (HVAC AHU PANEL MCC 01)

2 Nos. 40A, DP MCB's - (SPARE)

Panel as described above.

GROUND FLOOR PANEL 2 - GUEST HOUSE BLOCK

IP Rating : IP 42

Incomer

1 No. 63A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

100 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

1 Nos. 32A, 4P MCB's - (DB 1)

1 Nos. 32A, 4P MCB's - (HVAC AHU PANEL MCC 03)

1 Nos. 32A, 4P MCB's - (HVAC FAN PANEL MCC 14 GF)

2 Nos. 40A, 4P MCB's - (SPARE)

Panel as described above.

FIRST FLOOR PANEL 2 -GUEST HOUSE BLOCK

IP Rating : IP 42

Incomer

1 No. 100A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

2 Nos. 32A, DP MCB's - (Rooms DBs)

1 Nos. 32A, DP MCB's - (C.A. DB)

1 Nos. 32A, 4P MCB's - (HVAC AHU PANEL MCC 04)

2 Nos. 40A, 4P MCB's - (SPARE)

Panel as described above.

SECOND FLOOR PANEL 2 - GUEST HOUSE BLOCK

IP Rating : IP 42

Incomer

1 No. 100A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

160A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

5 Nos. 32A, DP MCB's - (Rooms DBs)

1 Nos. 40A, 4P MCB's - (HVAC AHU PANEL MCC 05)

1 Nos. 32A,4P MCB's - (C.A. DB)

2 Nos. 40A, DP MCB's - (SPARE)

Panel as described above.

THIRD FLOOR PANEL 2 - GUEST HOUSE BLOCK

IP Rating : IP 42

Incomer

1 No. 100A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

9 Nos. 32A, DP MCB's - (Rooms DBs)

1 Nos. 32A,4P MCB's - (C.A. DB)

1 Nos. 40A, 4P MCB's - (HVAC AHU PANEL MCC 06)

2 Nos. 40A, DP MCB's - (SPARE)

Panel as described above.

FOURTH FLOOR PANEL 2 - GUEST HOUSE BLOCK

IP Rating : IP 42

Incomer

1 No. 100A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

7 Nos. 32A, DP MCB's - (Rooms DBs)

1 Nos. 40A, 4P MCB's - (HVAC AHU PANEL MCC 07)

2 Nos. 40A, DP MCB's - (SPARE)

Panel as described above.

FIFTH FLOOR PANEL 2 - GUEST HOUSE BLOCK

IP Rating : IP 42

Incomer

1 No. 100A 25 KA, 4P MCCB

Incomer Metering & Indication:

415V / √3 / 110V/ √3 PT's, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy.

R,Y,B phase indication lamps (110V) LED Type

ON' & Trip indication lamps (110V) LED Type

Cast resin metering CT's for each phase of class-1 accuracy & of suitable burden & ratio

Incomer shall have suitable surge supressor/ TVSS

Bus bars

160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA.

Outgoings

9 Nos. 32A, DP MCB's - (Rooms DBs)

1 Nos. 32A,4P MCB's - (C.A. DB)

1 Nos. 40A, 4P MCB's - (HVAC AHU PANEL MCC 06)

Panel as described above.

Supplying of Following Sizes of 1.1 KV Grade Multicore Aluminium Conductor XLPE Insulated armoured cable conforming to IS:7098 (Part - I) complete with all Amendments etc. as Required

3.5 C X 300 Sq.mm Al. XLPE arm.

3.5 C X 240 Sq.mm Al. XLPE arm.

3.5 C X 185 Sq.mm Al. XLPE arm.

3.5 C X 150 Sq.mm Al. XLPE arm.

3.5 C X 120 Sq.mm Al. XLPE arm.

3.5 C X 95 Sq.mm Al. XLPE arm.

3.5 C X 70 Sq.mm Al. XLPE arm.

3.5 C X 50 Sq.mm Al. XLPE arm.

3.5 C X 35 Sq.mm Al. XLPE arm.

4 C X 25 Sq.mm PVC CU arm.

4 C X 16 Sq.mm Al. XLPE arm.

2 C X 6 Sq.mm Al. XLPE arm.

LT CABLE LAYING Laying of One Number PVC Insulated And PVC Sheathed / XLPE Power Cable of 1.1 kV Grade of Following Size Direct in Ground Including Excavation, Sand Cushioning, Protective Covering and Refilling the Trench etc. as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

LT CABLE JOINTING & END TERMINATION Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required.

2 X 6 sq. mm (19mm)

4 X 16 sq. mm (28mm)

4 X 25 sq. mm (28mm)

3½ X 35 sq. mm (32mm)

3½ X 50 sq. mm (35mm)

3½ X 70 sq. mm (38mm)

3½ X 95 sq. mm (45mm)

3½ X 150 sq. mm (50mm)

3½ X 300 sq. mm (70mm)

Supply & Testing of following 11 KV( UE) grade multicore Aluminium conductor XLPE insulated cable, insulation screening with extruded semi conducting compound in combination with copper tape armoured cores laid up, inner sheath of PVC tape, galvanised steel flat strip armoured and overall PVC sheathed cable conforming to IS: 7098 (Part - II) and complete with all latest amendments etc. complete as required.

3 C x 240 Sq. mm 11 KV (UE)

H.T. Cable Laying-DSR ITEM Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Above 120 sq. mm and upto 400 sq. mm

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single Red colour on front side as required.

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Above 6.5 metre and upto 8.0 metre

Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape , Hole Seeling to be done complete as required.

32 mm dia

SITC of First aid box as approved by Indian red cross conforming to IS : 2217.

SITC of CO2 Fire Extinguishers 4.5 kg capacity complete in all respect ISI : 15683 marked

SITC of of rubber gloves of 11 KV grade as per IS : 4770.

SITC of ANTI SKID RUBBER MAT 1 mtr x 2 mtr. 3mm thick ISI - 15652 marked

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching.

300 mm dia

250 mm dia

100 mm dia

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.. (BODY EARTHING)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.. (NEUTRAL EARTHING)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

RFID base boom barier with 6 metre wide Strong aluminium arm with rubber guard, Strong aluminium arm with rubber guard, Manual lock release by key in case of power failure, Green light and red light indicating the position of the beam, Connections for infrared photocell, loop detector & IC system for other functions, Stop and reverse operation safety devices, Provision for connecting an RFTD system.

Function

Open the door by scanning the tag.

After being stopped for a specific time, the system will automatically send a signal to close the barrier

The system can be configured with an ro card reader, allowing addition and deletion of users.

Technical Specification

Clear opening width 6 mtr

Power Supply- 230 V ~I 50 - 60 Hz

Control Panel- 24V

Torque- 250Nm

Opening Time- 1 - 2 s/90°

Protection Rating- IP 54

Operating Temprature- -20 degreeto +50 degree

Travel Control System- Encoder

RFID READER

RFlD UHF readers to enable the tagged vehicle identification from 10-12 meter distance so that it is convenient for drivers to access the boom barrier without stopping the vehicle.

Teachnical Feature:

Frequency- 865-867 MHz

Power Output- 865-867 MHz

Communication- 10/100 BaseT Ethernet (RJ45); USB Host & Client T e A & B) or Serial DB9)

Operating Temprature- -20 degreeto +50 degree

Humidity- 5-95% non-condensing

CIRCUIT CUM POINT WIRING Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit with modular switch modular plate suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc.as required. Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for the following light point with 2.5 sq.mm PVC insulated copper conductor 1100 volts grade stranded flexible FRLS wires of approved make in concealed or surface mounted 25mm dia 16 gauge MS conduit including provinding and controlled by SPMCB provided in the DB. (Cost of MCB not to be including here ) complete in all respect and as per direction of Engineer in charge.

Primary point controlled by one MCB.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

Wiring for power plug points with 2 x 4 sq.mm. FRLS PVC insulated, Cu. Conductor, single core cable in surface/ recessed steel conduit along with 1 No. 4 sq.mm. FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light plug points / power plug points with 4 x 4 sq.mm. FRLS PVC insulated, Cu. Conductor, single core cable in surface/ recessed steel conduit along with 2 Nos. 4 sq.mm. FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed Steel conduit as required

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4x 10 sqmm+ 2x 6 sqmm earth wire

4x 16 sqmm+ 2x 6 sqmm earth wire

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required

Supply & fixing of following sizes of medium class PVC conduit along with accessories in surface / recessed including cutting the wall & making good the same in case of recessed conduit as required.

32 mm dia.

Supplying and fixing of Stepped type 2 module electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 Amp modular socket outlet and 5/6 A modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 Amp modular socket outlet and 15/16 A modular switch, connection etc. as required.

Supplying & fixing of 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing extra conduit down rod of 20 cm lengthG.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

100 Amp, 30 KA,FP MCCB

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way, Double door

8 way, Double door

12 way, Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator).

6 way (4 + 18), Double door

8 way (4 + 24), Double door

12 way (4 + 36), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32 A, 415 V “C” curve TP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Installation, testing and commissioning of wall bracket / ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting complete with all accessories including connections etc. as required

Supply of Light fixture as given below Supply of 36 W recess mounted LED back-lit 2’x2’ with high efficient LED’s, CCT 5700 - 6500 K,CRI≥80, System lumen 100lm/W, Lumens ≥ 3600, white powder coated CRCA with PMMA opal diffuser for glare free & uniform lighting, minimum burning hour life >50000 hours. Driver shall be of constant current type, operating temperature from -10 to +45 degree celcius, power factor>0.95, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge.

Supply of recess mounting 18 W LED down light with 50000 burning hours. high efficient LED’s, CCT-5700k -500 K,CRI >80, Lumens ≥ 1800, single piece pressure die cast powder coated housing with opal diffuser for glare free & uniform lighting, Driver shall be of constant current type, operating temperature from -10 to +45degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge.

Supply of recess mounting 12 W LED down light with 50000 burning hours high efficient LED’s, CCT-5700-6500 K,CRI >80, Lumens ≥ 100lumen/watt, with aluminium die cast housing with opal diffuser for glare free & uniform lighting, Driver shall be of constant current type, operating temperature from -10 to +45degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge.

Supply of surface mounting 12 W LED down light with 50000 burning hours high efficient LED’s, CCT-5700-6500 K,CRI >80, Lumens ≥ 100lumen/watt, with aluminium die cast housing with opal diffuser for glare free & uniform lighting, Driver shall be of constant current type, operating temperature from -10 to +45degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge.

Supply of recess mounting 6 W LED down light with 40000 burning hours high efficient LED’s, CCT-5700-6500 K,CRI >80, Lumens ≥ 90lumen/watt, with aluminium die cast housing with opal diffuser for glare free & uniform lighting, Driver shall be of constant current type, operating temperature from -10 to +45degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge.

Supply of recess mounting 7 W LED COB down light with 40000 burning hours high efficient LED’s, CCT-5700-6500 K,CRI >80, Lumens ≥ 90lumen/watt, with aluminium die cast housing with opal diffuser for glare free & uniform lighting, Driver shall be of constant current type, operating temperature from -10 to +45degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge.

Supply of E27 base decorative type single headed wall mounted light fixture. Housing made of Metal, Synthetic, glass in Bronze finish. Operating voltage 220-240V, 50Hz. Make- Philips- Model No. Philips 31425 / Havells- Model No. LHJE01104499 / Bajaj- Model No.- 112775.

Supply & erection of 20 watt LED Betten Tube Light, 4' long suitable with 40000 burning hours for rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%, AC supply with aluminium alloy base,, frosted polycarbonate diffusers with power factor >0.90, Total Harmonic Distortion (THD) < 20%, system current - 0.085A, system efficiency > 85% , with operating temp. -10° C to 45° C, Lumen output for LED tube should be > 2000 lumen and overall lumen/watt of luminaire should be greater than 80%, C.R.I. of LED>80% with correlated colour temperature (CCT) of 6500K , minimum burning hour life >40000 hours,LED viewing angle 120 Degree complete in all respect with the entire satisfaction of the Engineer-in-incharge. Supply of Industrial General Purpose 4' long tube fitting suitable to house 1x20w LED tube rod 4' long, Polycarbonate housing , rated voltage 240 V and Ingress protection IP-20 complete in all respect with the entire satisfaction of the Engineer-in-incharge.

Supply of LED Bulkhead with a nominal system lumen output of 700 lumens and a minimum system efficacy of 105 lm/W. The luminaire shall have a rated system lifetime of 25,000 burning hours at L70. The luminaire should have a color temperature of 5700K and CRI > 80. The luminaire shall meet IP65 rating and IK 08 rating with THD < 20% and PF > 0.9. The luminaire housing should made of pressure die cast Aluminium with polycarbonate front diffuser. The total power consumption should not exceed 6.5W (including driver).

Supply of 11 W mirror light with high efficient LED’s, CCT-6500 K,CRI >70, Lumens ≥900, with Ingress protection IP-20, with 50000 burning hours Driver shall be of constant current type, operating temperature from -10 to +45 degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge.

Supply of LED exit signage of Box size in mm 325x425x365(Make- Prolite, Model No. PEL LED E/NM (RM) W, Code No. E 109) or Equivalent to Philips, Trilux, Havels .

Supply of LED aviation light luminaire (Make Havells, Philips or equivalent).

Supplying of Plastic Body Ornamental Exhaust Fan heavy duty 230V A.C 50 cycles, 300 mm sweep, 1300 rpm, energy efficient, complete erected in position with all accessories. Make- Havels- Venti Air DS, or Equivalent to Orient- Ventilator DS, Cromptong & Greaves- Ventilus 250 or equivalent as per specification.

Supplying of wall bracket fan 230V A.C 50 cycles, 400 mm sweep, energy efficient, complete erected in position with all accessories.

Supply of 240V, 50 Hz, 380 rpm ceiling fan having dia 600mm having minimum 225 CMM air delivery of approved makes as per relevant standard and tender specifications including all accessories like down rod, blades,canopy,etc complete in all respects as per IS: 374-1979 & approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying,Installation,Testing and Commissioning of Passive Infrared(PIR) technology based occupancy sensor having high preformance, non regulating programmable type, suitable for connected load upto 10 Amp, for mounting height up to 2.8 meter and for 5 meter diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.

Lighting Automation Supply, Installation,Testing & Commissioning of Lighting processor has built-in astronomical clock. Processor Link- 2 RJ-45 ports with built in switch for daisy chaining processors (max 16 processors). Shpuld support integration with third-party systems and communication between multiple processors. processors may be connected using either an Ethernet hub /switch or router, or by using Ethernet directly from a PC to the processor. Power : Processor (P): 24–36 V - 250 mA; Links (L1 / L2): 24–36 V - 2 A per link. Regulatory Approvals : cULus, NOM, CE, Cooling Method : Passive Cooling. Should be supplied with standard accessories as required. Approved Make:Lutron/Zumtobel/Leviton

Supply, Installation,Testing & Commissioning of power supply for above processor, Input Power: • Nominal input voltage: 100–277 V~, • Frequency: 50/60 Hz, • Current consumption, fully loaded (typical): 0.7 A (230 V~). Power Supply Output: • Nominal output voltage and tolerance:24 V- / ±1%, 75 Power Draw Units (PDUs), • 2.5 A SELV / PELV / NEC® Class 2, • Power Draw Units (PDUs): Supplies 75 PDUs maximum. Approved Make:Lutron/Zumtobel/Leviton

Supply, Installation,Testing & Commissioning of Wire Landing Board, wire landing board is a wiring aid consisting of a printed circuit board with one set of five terminal blocks. Approved Make:Lutron/Zumtobel/Leviton

Supply of Low Voltage Enclosure provides a compact housing for mounting one processor or one system interface and up to two wire landing boards. Approved Make:Lutron/Zumtobel/Leviton

Supply, Installation,Testing & Commissioning of DIN Rail mounted 4-zone Switching module, Each zone is rated at 5A for switching of inductive, capacitive, or resistive loads. Includes communication link to any device (max 100) and one contact closure input /output link, Should be Rated for lighting loads as defined by IEC/EN 60669 as well as INC, MLV, and ELV, 220-240 V~ 50/60 Hz, Single input feed, Lightning strike protection meets ANSI/IEEE standard C62.41 and IEC 61000-4-5. Can withstand voltage surges up to 6000 V~ and current surges up to 3000 A. Approved Make:Lutron/Zumtobel/Leviton

Supply, installation, testing and commissioning of Direct dimming module, with 4 feed suitable with 10 A maximum total input current for leading/ trailing edge dimming outputs. Should have a bypass contact closure input builtin without connecting any external devices . Each zone has no minimum load requirement. Should support One load type per zone. Should be RoHS Compliant, IEC/EN 60669-2-1, CE marked. Approved Make:Lutron/Zumtobel/Leviton

Supply, Installation,Testing & Commissioning of motor control power module,Input voltage: 230 V~ 50/60 Hz, 6 A maximum total input current, BTU/hour when fully loaded: 5, Ambient temperature operating range (inside mounting panel): 0 ºC to 40 ºC (32 ºF to 104 ºF), Each motor control power module counts as 4 zones (outputs) and 1 device . Approved Make:Lutron/Zumtobel/Leviton

Supply of Wireless Occupancy/Vacancy Sensor for rooms with a frequency of 865 MHz, Ceiling mount, infrared, 37.2 sq m (400 sq ft), battery-powered, 102 mm (4.0 in) diameter, white. Approved Make:Lutron/Zumtobel/Leviton

Supply of Sensor Module, to connect 10 numbers of sensors either of the Occupancy / Daylight / Personal sensors/Pico. No wired connections, ceiling mount Approved Make:Lutron/Zumtobel/Leviton

Supply, installation, testing and commissioning of wall-mounted 4-button Keypad, wired keypad allows the user to control lights, shades/ draperies, temperature, and 3rd-party equipment. Large buttons are easy to use and button engraving is easy to read. Buttons with white, backlit engraving make it easy to find and operate the keypad in low light conditions. Keypads are available in a variety of colors, finishes, and button marking options. Approved Make:Lutron/Zumtobel/Leviton

Supply, installation, testing and commissioning of wireless control keypad, flexible and easy to use device that allows the user to control wireless load-control devices from anywhere in the space. Can provide control of blinds, curtains, or lighting devices within a range of 30 ft (9 m) through walls and 60 ft (18 m) line-of-sight. Should be BAA-compliant. Approved Make:Lutron/Zumtobel/Leviton

Supply, installation, testing and commissioning of distribution boxes that serve as the load centre and distribution of power. Approved Make:Custom

Supply, Installation, Testing and Commissioning of 6 conductors Control Non-Plenum rated cable with 2x 12 AWG, 1 x 18 AWG, 2 x 22 AWG and 1x 24 AWG drain. Approved Make:Lutron/Zumtobel/Leviton

Supply, installation, testing and commissioning of Curtain Motor -35 KG controlled by automation. Nominal torque: 0.6 Nm, Maximum stall torque:0.7, No load speed: 105 rpm, Nominal speed: 105 rpm, Working temperature:0°C to +60°C 85%HR at 35°C, Voltage range: 90 to 264 Vac, Frequency range: 47 to 63HZ, Maximum Current(A): 0,6 at 120VAC ; 0,3 at 240VAC, Approved Make:Lutron/Somfy

Supply, installation, testing and commissioning of Curtain Track 2-3 metre. Approved Make:Lutron/Somfy

Supply, installation, testing & commissioning of Set of 2 Nos. 40 KVA/32 KW UPS. Each UPS of 40KVA should have following specifications in addition to tender requirements : True online double conversions, IGBT Rectifier & inverter based UPS. Three phases Input/ three phase output with SMF batteries complete with MS Fabricated battery rack to accommodate the all battery system, Suitable for 30 Min backup on Full load at 0.8 Load P.f., with 20 nos. 120AH Battery with Each UPS, Input voltage operations on mains without switch over to battery : 340-478V at 100% load, 220-478 V @ 50% load. Input power factor 0.99 @ 100% linear load, input THDi less than 5% @ 100% linear load. Output THD is less than 3% for full linear load & Less than 5 % for nonlinear load. Crest factor 3:1, over load 125% for 10 min, 150% for 1 min, UPS should be able to operate continuously at 115% load on bypass mode. Battery Flexible design shall be available from 36 to 40 or better. Battery type should be Valve regulated lead-acid (VRLA). Inbuilt Delta - Star Input Isolation Transformer with each UPS Shall be provided, parallel communication port, RS232, USB, EPO and SNMP interface, BMS interface, Dust Filter at Air Inlet point are required.

LCD Display indicating all important parameters. To improve the UPS Security over LAN/WAN the SNMP card provided with UPS shall be having Cybersecurity enhancements for IEC / UL 2900-2-2 certification, including stronger encryption, configurable password policy. The card shall work on GIGABIT Speed and should support all major protocols. UPS shall be provided with Temperature Humidity Sensors to monitor Temperature and Humidity over LAN through SNMP card Software. Battery open rack with top cover, battery interlinks, battery breaker(MCCB), Battery breaker enclosure, battery to UPS cable as required should be provided with UPS systems. UPS system shall be parallelable upto 4 units in case required in future. Each UPS shall be compatible for working in parallel redundant mode with other and should be able to be used with Lithium Ion Batteries if required in future. Offered UPS Model shall be type tested in line with IEC 62040-3 standard from third party NABL Approved lab. UPS Make: APC, Powerware, Gutor, Eaton, GE, ABB Battery Make: Panasonic, Exide, Quanta, Amara Raja

Supply, errection, testing & commissioning of 13 passanger with machine Electric Traction Elevator, to be errected in accordance with followingTechnical Specification & as per latest IS Specifications.

Nos. of Lifts 1 Nos.

Type & Capacity:Passanger Elevator App. 884 kg. 13 person.

Speed mps : 1.5 mtr per second

Travelling (max.) in mtrs : Approx. 36.3 mtrs

Serving : 11 stops, 11 opening (All opening on the same side).

Power Supply : 415V, 3 phase, 50 HZ AC supply.

Control : Simplex full collectivecontrol with or without attendant.

Operation : Automatic

Motor : A Synchronous motor

Car Size : as per manufacturer design.

Door Frame : Full Glass Door.

Well Size- 2.5 M deep x 2.0 M wide

Other Features :

Battery operated emergency alarm and emergency light with rechargeable battery.

Adjustable guide shoes.

Combine Luminous hall buton and digital hall indicator/touch screen.

Integral full height car opening panel with luminouscombined with direction arrows, overload warning indicacator & service cabinet.

Hand free press & speak intercom with EPABX for three way communication.

Automatic rescue device to automatic bring the elevator to a landing in case of power / phase failure/ low voltage.

Full height Infrared safety curtain & automatic floor announcer.

Diffused Lighting in car.

Blower (noiseless)

Looking mirror in front side of lift car.

Face Plate finish : Stainless stell in hairline.

Face Plate : Rectangular.

The Three feet high railing shall be provided on car top.

The motor shall be high starting torque and low starting current and shall be arranged for self lubrication.

Proper weight screen shall be provided at the hoist way.

Fire retardant compound coated traveling cable shall be used.

2Phase Device Fire Man Drive & Fireman switch at ground floor.

Load Weight device with overload bypass feature.

Steel itels such as Door Frames Sill angles, Fascia Plates, Spring Buffers.

Bralite Features, Lift announcement system, Pit ladder, Hand Rail & Additional Car Gate Lock.

Three side Hand Rail in Stainless Steel Finish.

System Capable of withstanding +10% to -10% Variation in Supply Voltage Fluctuations.

Car Plateform constructed out of Cold Rolled Grain Oriented Formed Sheets of Steel.

Fire Rated landing Doors for a period of two hours only.

The whole machinery shall be mounted on appropriate anti vibration supports to minimize voice & vibration.

Supply, Installation, Testing and Commissioning of 2.5 LB capacity Novec 1230 , DLP Assembly with automatic valve, push in connector for tube, 2.5 LB Novec 1230 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation.

Supply, Installation, Testing and Commissioning of 5 LB capacity Novec 1230 , DLP Assembly with automatic valve, push in connector for tube, 5 LB Novec 1230 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation.

Supply, Installation, Testing and Commissioning of 10 LB capacity Novec 1230 , DLP Assembly with automatic valve, push in connector for tube, 10 LB Novec 1230 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation.

Supply, Installation, Testing and Commissioning of Linear pneumatic heat Detection Tube with all necessary fittings & supports.

Supply, Installation, Testing and Commissioning of Master Control Unit with Audio Visual Alarm with wiring to make complete system operational . The control Panel should have provision for integration with fire Alarm /SCAD/BMS System.

LIGHTNING PROTECTION SYSTEM Supply of Earthing termination made of copper-bonded rod of 10 feet length,14 mm dia. (Minimum copper bonding shall be 0.25mm) along with Rod-to-Conductor connectors, Earth enhancement material (25 KG resistivity each less than 0.12 ohm meter), Pit Cover and other accessories as required and as per r and other applicable codes.

Providing and fixing of lightning conductor finial, made of 25 mm dia 1200 mm long, copper tube, having single prong at top , with 85 mm dia 3 mm thick copper base plate including holes with insulation etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run).

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

CABLE TRAY Supports, bends, access boxes, tap off boxes and cross over as per site requirement. (overhead / wall mounted recovery & junction boxes shall be 2.0 mm thick). The pregalvenised sheet shall be as per IS 277 or BS 2989 having tensile strength of minimum 500 N/sq.m. and minimum zinc coating of 275 GSM.

Supplying, installation, testing & commissioning of Race way made from minimum 2.0 mm thick GI raceway, factory fabricated, with internal partition of the following sizes including providing removable double folded cover of 2.0 mm thick , knock out holes and fixing accessories & coupling, earthing stud for terminating 8 SWG copper earth wire complete as required

100 mm wide x38 mm deep in ceiling/floor

150 mm wide x38 mm deep in ceiling/floor

225 mm wide x38 mm deep in ceiling/floor

300 mm wide x38 mm deep in ceiling/floor

Supplying, installation, testing & commissioning of floor/ceiling recessed 2 mm thick pregavanised sheet outlet junction box including providing cover with provision to adjust overall height, knock outs on four sides to accept raceways of specified sizes and cutouts to fix required outlets for following size of race ways with painted GI plate ( Colour as approved Architect/Consultant).

Supplying and installing following size of perforated Hot DippedGalvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 2 mm thickness

900 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 2 mm thickness

900 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

900 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Cross member” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

900 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

50 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

900 mm width X 62.5 mm depth X 2.0 mm thickness

VRV/VRF Outdoor Unit with Heat Pump Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume aircooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll/Rotary Compressor(s), minimum two compressors for above 14HP modules, microprocessor based Controller, topdischarge type condensing unit(s), with R410A Refrigerant, vibration isolators, with suitable foundationetc. completeas required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V+/-10%, 3Phase, 50HzAC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5

20 HP Outdoor unit VRV/VRF

24 HP Outdoor unit VRV/VRF

60 HP Outdoor unit VRV/VRF

Indoor Unit- Cassette Type Supply, installation, testing and commissioning of following minimum capacity4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable mediapre-filter, fansection with low noise fan/dynamically balanced blower, multispeed motor, coilsection with DXCoppercoil electronic expansion valve, outercabinet, drainpump, grill, necessary supports, vibration isolation, cordless remote control etc., suitable for operationon single phase 230V±10%, 50Hz ACsupply, complete as required. The unit shall have automatic force shut down provisionin case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at airinlet conditions of 27Degree CD Band 19 Degree CWB temperature.

Indoor Unit- Ductable Type Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/ dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiveing signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. Low static ductable units (minimum 25 pascal external static pressure)

Mid Static Ductable units (minimum 45 pascal external static pressure)

High Static Ductable units (minimum 110 pascal external static pressure)

COPEER REFRIGERANT PIPING Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19mm thick insulation

28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19mm thick insulation

31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19mm thick insulation

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19mm thick insulation

38.1mm dia (OD) (Harddrawn) with tube thickness 1.62mm with 19mm thick insulation

41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19mm thick insulation

Supply, Installation , Testing and Commissioning of following imported fittings to be provided in refrigerant pipe line. Material of construction for fittings shall be similar to refrigerant piping.

Y- joints for refrigerant piping .

Accessories SITC of Expansion Kit cum control kit Required for the above AHU to make the system complete (Incl, Standby AHU Coil)

Spcl. Note : If any AHU/TFA at terrace lvl. Than that will be with weather proof canopy so it should be cross check with dwgs. and at site accordingly pricing quoate .

Propeller fan

Supply,installation,testing and commissioning of Certified Propeller fan of the following capacity of approved make and specification. Fan shall be supplied with aluminum gravity louver & bird screen and Speed Regulator.

200 mm dia propeller fan, with single phase motor

300 mm dia propeller fan, with single phase motor

Inline fan Supply, installation, testing and commissioning of Certified Circular/Rectangular swing type Inline fan with fiire retardent Canvas connection Speed Regulator of the following capacity of approved make and specification.

50-450 CFM, 5-7 mm SP WG with Single phase motor

500-550 CFM, 7-10 mm SP WG with Single phase motor

600-800 CFM, 10-12 mm SP WG with Single phase motor

Tube Axial Flow fans SITC of Long case Tube axial flow fans, as per specifications and approved makes suitable for three phase operation at 1450 RPM respectively Normal/Smoke case.

SITC of AMCA Certified (For Air and Sound Performance) tube axial flow fan of different capacity as mentioned below in standard M.S.contruction. Entire fan model & AMCA Seal shall apear in techncial submittal of fan. All the fans are synthetic enamelled panited/hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at inlet. The electric motor coupler shall be squirrel cage induction motor (IE-3 type) confirming to IS - 325-IP - 55 with class `F' insulation. Fan efficiency should not be less than 70 %, noise level should not be more than 85 db @ 3 m distance when measured in hemisperical reverberant room conditions. Fans should be as per specification and drawings. (As per Vent. Fan Schedule ) (Pressurization Fans with St. Press. of 40 mmWG)

9000-10000 CFM (For Stairwell/Liftwell/lobby Pressurization)

17000 -18000CFM (For Lift well/lobby Pressurization)

21000 CFM (For Stairwell/Lift well/lobby Pressurization)

16500 CFM , 30 mmwg SP (For Normal & Make Up air Basements)

25500 CFM , 30 mmwg SP (For Normal & Make Up air Basements)

8500 CFM , 30 mmwg SP (For Make Up air )

17500 CFM , 30 mmwg SP (For Make Up air )

SITC of AMCA Certified (For Air and Sound Performance) tube axial flow fan of different capacity as mentioned below in standard M.S.contruction. Entire fan model & AMCA Seal shall apear in techncial submittal of fan. All the fans are synthetic enamelled panited/hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at inlet. The electric motor coupler shall be squirrel cage induction motor (IE-3 type) confirming to IS - 325-IP - 55 with class `H' insulation. Motor shall be of high temperature resistance "Class H Smoke Spill" 250° C for 2 hrs. Fan shall be EN 12101-3 Certified & CE/UL Listed for high temprature. Fan efficiency should not be less than 70 %, noise level should not be more than 80 db @ 3 m distance when measured in hemisperical reverberant room conditions for Normal mode Fans and noise level should not be more than 85 db @ 3 m distance when measured in hemisperical reverberant room conditions for Emergency mode Fans. Fans should be as per specification and drawings (As per Vent. Fan Schedule ). All Fans Should be VFD Compitable.

5500-6000 CFM, 25 mmwg SP For Upper Floor Smoke extract

1500-2500 CFM, 25 mmwg SP For Normal & Smoke extract

16500 CFM, 25 mmwg SP For Normal & Smoke extract

21000-21500 CFM, 25 mmwg SP For Normal & Smoke extract

23000-25500 CFM, 25 mmwg SP For Normal & Smoke extract

Evaporative air cooler(Air Washer) Supply , Install, test and commission double skin Evaporative air washer as per specifications , suitable for the following capacity given below at 75-90% efficiency of evaporative medium. The fan shall be of DIDW centrifugal construction. Packaged Type

Ventilation fan sections of double skin construction as described above and in the specifications DIDW type,motor within the casing.All fans shall have multi speed motors Cost to be inclusive of unit isolator and .25HP-0.5HP water pump. Fan Motor VFD Compitable. AS PER SPEC.

24000 CFM, 3PH, 40 mm WG static pressure,960 rpm, 1.0HP motor with Speed controller for floor mounted

Air Scrubber (DRY Type) DRY SCRUBBER : Kitchen Exhaust Supply, Installation, Testing and Commissioning of Dry Scrubber comprising of extract air intake section, electrostatic precipitation technology, dry type air cleaner to remove odour, smoke and fumes from exhaust air.

Electrostatic section shall be made of 16 gauge galvanised sheet,high bake epoxy powder coated, washable type aluminium mesh filters, stainless steel spiked ionizers to create high voltage DC field, Stainless Steel 316 collector plates which should be alternatively charged positive and negative with large collecting area with 14" deep cell, to work as magnet for charged smoke and oil particles. Average efficiency of 95% and more in single pass as per DOP test method. Electrostatic Precipitator should be able to charge particles from 0.01 micron to 10 microns through solid state power supply. The system should be fitted with interlock switch for safety. The system should allow connection to a fan section to achieve 500 FPM velocity across the air cleaner.

3500 CFM for Kitchen Exh.

3000 CFM for Kitchen Exh.

CO SENSOR Supply, installation, testing and commissioning of CO sensors . The car park ventilation systems shall be controlled by an individual CO-Monitoring system for entire car park located on each level to optimize efficiency. The contactors within the motor control panel shall be controlled by a Carbon Monoxide monitoring panel which shall contain DDCs (Direct Digital Controllers) where the pre-determined switching strategy and logic shall be loaded. The CO monitoring panel shall receive signals from CO sensors located throughout the levels at a spacing of no. more than 1 per 350 m2. The 24Vac power supply for the CO sensors shall be mounted in the same panel. The power supply shall be looped across the CO sensors. The proposed CO sensor shall provide a 0-10 VDC signal for measuring the CO level in the car park area. CO monitoring devices shall be mounted remotely throughout the car parks. The devices shall be mounted in accordance with the manufacturers guidelines but no greater than 1.5 m above FFL. CO Sensor shall be suitable for wall mount & capable of following features: (As per 350 sqm covered area) for Basement ventilation.

Digital display of the CO level : 0 to 200 ppm

Analog output : 4 to 20 mA / 0-10VDC

Low Voltage operation : 24 VAC / VDC

Test Switch : Provides mode for system self test.

Automatic Calibration (Field Calibration Kit)

Over-range indication.

Start-up mode : steps display and output through test ranges.

Solid – Stat sensor : Life expectancy of 7 to 10 years.

Multiple sensors with one power supply.

Variable speed drives.

Supply , Install, test and commission Variable Speed Drive package as described above and in specifications suitable for for 0.55 to 1.5 kW motor rating as per the specifications(3 Phase variable frequency output for Exh. Fan, . These variable speed drives shall get the input from the remote air differential pressure adjuster , as described above in item.

Supply , Install, test and commission Variable Speed Drive package as described above and in specifications suitable for for 7.5 -9.3kW motor rating as per the specifications(3 Phase variable frequency output for Normal Exh. Fans. These variable speed drives shall get the input from the remote air differential pressure adjuster , as described above in item.

Supply , Install, test and commission Variable Speed Drive package as described above and in specifications suitable for for 2.2-3.7 kW motor rating as per the specifications(3 Phase variable frequency output for Normal Exh. Fans , . These variable speed drives shall get the input from the remote air differential pressure adjuster , as described above in item.

Supply, Installation, Testing and commissioning of comprehensive Air Purification system in the specified areas where AHU/ Cassette /Hi-wall / Ductable units etc are installed , so as to improve Indoor air quality by using Needlepoint Bi-polar Ionization technology, which produces a natural Bio Climate rich in positive and negative ions. The Needle Point Bipolar Ionizers should not have any consumables and should have a life of 10 years. System should be fitted with Fine Filter Media with very less static drop acceptable upto 5 mmwg of Initial pressure drop wherever requires. Along with indoor Air quality monitor to measure Air quality parameters including PM2.5, TVOC, CO2, Humidity and Temperature. This monitor should be a 3 tier architecture including sensor Hardware, secure cloud infrastructure, monitoring apps including dashboard, android/IOS apps, where ever requires Project design should meet standard ASHRAE 62.1 IAQ Procedure for energy saving. System should kill microorganism and pathogens, remove Odour, VOC and reduce dust particle /particulate matter / PM2.5 /PM 10. The product should be UL / Intertek listed. Product should have minimal or negligible pressure drop & low power consumptions. Product should have UL 867 and UL 2998 certification (for zero ozone emission). The Product shall have been Tested on COVID-19 Surrogate for its efficacy. The System should be capable of providing periodic Prventive maintenance for automated after sales support service in form of notification/alerts and user interaction through dashboard application

7500 to 13500 CFM, 48 Watt

300 to 2800 CFM, For IDU Duct Mount

AIR CURTAIN Supply,installation testing and commissioning of AIR CURTAIN of following size as per approved make and with Door limit switch/sensor with multi speed regulator .(At ground entrance)

1500 mm long (High flow type)

1800 mm long (High flow type)

2100 mm long (High flow type)

CONDENSATE DRAIN PIPE Supplying, fixing,testing and commissioning of following PVC pipes for condensate drain duly insulated with kinny foam & vapour barrier duly secured with adhesive tape as per specification ,cut to required length and installed with all joints , including the necessary fittings. (For all the AHU/FCU units upto the main header in the shaft dor vertical risers)

50mm dia

40mm dia

30mm dia

25 mm dia

Refrigerant-410a Supply , charging & Leackage testing of refrigerant -410a in additional copper piping circuit.

AIR SIDE WORKS Site Fabricated Duct - GI duct Supply,Installation,balancing and commissioning of fabricated at site GSS sheet metal ducts (rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter,vanes, hangers, supports etc.) in accordance with the approved shop drawings and specifications , and shall also confirm to the BIS specifications.The duct shall be fabricated at site for to suit pieces.

Spcl. Note: All Duct Supprots incl. Supply, Fabrication, installation and testing of Steel Wire Ropes and Hangers, Supports and Modular system – Wire rope Supports (double channel wedge lock, unlocking device should not be integral part of grip for added safety) complete with end fixing. Wire Hangers shall be independently tested by reputed third party testing organization to sustain safe working load for 120min at elevated temperature of 175 deg. C or above. System shall be in accordance with the approved shop drawings and as required by the specifications

0.63mm (24 gauge) GSS

0.8 mm (22 gauge) GSS

1.0mm (20 gauge) GSS

1.25mm (18 gauge) GSS

Factory Fabricated Duct - GI duct Supply,Installation,balancing and commissioning of factory fabricated GSS sheet metal ducts (rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter,vanes, hangers, supportsetc.) in accordance with the approved shop drawings and specifications , and shall also confirm to the BIS specifications.The duct shall be fabricated at site for to suit pieces.

Spcl. Note: All Duct Supprots incl. Supply, Fabrication, installation and testing of Steel Wire Ropes and Hangers, Supports and Modular system – Wire rope Supports (double channel wedge lock, unlocking device should not be integral part of grip for added safety) complete with end fixing. Wire Hangers shall be independently tested by reputed third party testing organization to sustain safe working load for 120min at elevated temperature of 175 deg. C or above. System shall be in accordance with the approved shop drawings and as required by the specifications

0.63mm (24 gauge) GSS

0.8 mm (22 gauge) GSS

1.0mm (20 gauge) GSS

1.25mm (18 gauge) GSS

Supply, Fabrication, Installation and testing of Insulated Al. Flexible ducts in accordance with the approved shop floor drawings and specifications and shall also confirm to the BIS specifications.

150 mm Dia.

Grilles/Diffusers Supplying and fixing of Extruded aluminium supply and return air grilles/diffusers/louvres with dampers, supply air plenum etc. duly powder coated as per specifications and drawings.

Aluminium supply air grilles with damper.

Aluminium return air grilles without damper.

Aluminium supply air square diffuser with damper

Aluminium return/exhaust air square diffuser without damper.

Aluminium return/exhaust air Valve circular/squirell diffuser without damper.

Linear air grilles (150 MM wide)

Aluminium supply air collar damper

AI Volume control dampers for ducts

Fresh Air/Exhaust Air Louvers Supplying and fixing of extruded aluminium louvres with frame bird screeen , mounting arrangement etc. as per specifications and drawings.

Fresh Air/Exhaust Louvers

MOTORIZED FIRE AND SMOKE DAMPERS Supplying, fixing, Testing and commissioning of fire dampers in suppy air duct/main branch and return air path as and where required of required size i/c control wiring ,the damper shall be motorized combination fire and smoke damper (spring return type) of approved make of atleast 120 minute fire rating and as per the specifications as detailed earlier in the relevant sections.The fire damper shall be complete with electronic temperature sensor and electrically operated actuator .The fire dampers shall be located in the supply/return air ducts, at all fire rated crossovers (shafts/walls etc.) The control panel will be such located that the reset can be easily done These combination smoke and fire dampers shall be interlocked with the building management system for fire detection / HVAC and shall trip/close in the event of fire / smoke in the respective zone .

Bare Fire Dampers with 400 mm sleeve

Control panel actuator , including Electrical,spring type actuator,remote indication of the fire damper position.

Supply and Installation of Fire Resistant Fabric Flexible Connection to be installed between all the Fans,AHU/Indoor Units, AHU and the ducting to provide flexibility of movement in case of a seismic event and to prevent transmission of vibration from the unit to the duct. The fabric should be fire resistant, fiberglass weave with silicone rubber coating with Galvanized metal strip as per specifications. Flexible duct connector fabric shall be air tight, waterproof, virtually chemically inert and shall not emit toxic fumes when exposed to open flame.. The flexible canvas connectorshall be tested and certified in accordance with BS 476 Part 7 Class 1 and NFPA 701 from NABL accredited laboratory.

Supply and Application of fire retardant Coating CISBOND FR 802 having fire rating for 2 Hours at 250˚C Conforms BS 476 Part 6 & 7 Warrington Fire UK, pull of adhesion as per ASTM D4541, Impact resistance as per ASTM 2794 in accordance with Building Regulations on kitchen ventilation ducts & smoke extract ducts & all the joints must be filled with the acrylic water base fire retardant sealant for duct joints CISCRYL DS 50 as per the specifications. Spcl. Note: In Air Distribution Works Smoke extract Duct should be fire rated for 2 hrs. as per given boq item.

MECHANICAL INSULATION DUCT LINE ACOUSTIC TREATMENT Supply and installation of cross linked open cell Oxide Acetate ( Acco Isolate) Foam/Nitrile Rubber Acoustic insulation on ducts having density of 30 to 60 Kg/ M³ ,having K value 0.029 W/m ° K at 0°C Deg temp and temp range of -70°C to +100°C and fire rating Class O as per BS 476 Part 6 from CBRI,Roorkee and CFC/HCFC free as per US EPA 5021 A(2014 ). • Smoke & Toxicity index of material shall be passed as per IMO MSC 307 ( 88 ) 2010 Anexx 1 Pt 2 and as per the approved specifications.

15mm thick Acoustic open cell insulation on one side for Duct acoustic insulation

DUCT LINE THERMAL INSULATION Supply and installation of cross linked closed cell Oxide Acetate ( Thermo Isolate) Foam/Nitrile Rubber Thermal insulation on ducts having density 0f 30 ±3 Kg/ M³ ,having K value 0.029 W/m ° K at 0°C Deg temp and temp range of -70°C to +100°C and fire rating Class O as per BS 476 Part 6 from CBRI,Roorkee and CFC/HCFC free as per US EPA 5021 A(2014 ). • Smoke & Toxicity index of material shall be passed as per IMO MSC 307 ( 88 ) 2010 Anexx 1 Pt 2 and as per the approved specifications.

25 mm thick insulation with Two layer 7 mile cloths with adhesive on supply/Return/Exh. air duct on exposed area

13 mm thick insulation

9mm thick insulation

EXPOSED ROOF INSULATION Supply and installation of cross linked closed cell Oxide Acetate ( Thermo Isolate) Foam/Nitrile Rubber Thermal insulation on ducts having density 0f 30 ±3 Kg/ M³ ,having K value 0.029 W/m ° K at 0°C Deg temp and temp range of -70°C to +100°C and fire rating Class O as per BS 476 Part 6 from CBRI,Roorkee and CFC/HCFC free as per US EPA 5021 A(2014 ). • Smoke & Toxicity index of material shall be passed as per IMO MSC 307 ( 88 ) 2010 Anexx 1 Pt 2 and as per the approved specifications.

19mm thick oxide acetate insulation for underceck plain

ASSOCIATED ELECTRICAL WORKS The rates for the distribution boards from the Breakers and instruments shall also include the following :

Wiring for light / Fan points with 1.5 sq. mm PVC insulated copper conductor 1100 Volt grade stranded flexible FRLS wires of approved make in 1.6 mm thick 25 mm dia MS conduit including cost of providing & fixing saddles, hangers, supports, cutting chases and filling chases for recessed conduiting, and including the cost of providing and fixing a 6 amp 240 Volt Modular Plate type switches of approved quality, colour, make and design with moulded cover plate in zinc chromate passivated MS box and including the cost of running 1.5 sq. mm PVC insulated copper earth wire for loop earthing etc. complete

TPN ACB’s / MCCB’s shall mean 3 pole ACB’s / MCCB’s with adequate size of neutral link.

All MCB’s shall be of minimum 10 KA breaking capacity and MCCB 's shall be not lessthan 25KA

The breaking capacity of MCCB’s are mentioned panel wise. All MCCB’s shall be with thermal magnetic microprocessor releases as per BOQ and following :

i. MCCB rating upto 250 Amps with thermal magnetic releases.

ii. MCCB above 250 Amps with microprocessor releases.

All MCB’s used for protection of resistive and lightly inductive load shall be type “B” characteristic and inductive (motor) load shall be of type “C” characteristic.

Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993.

i. IP 42 for indoor panels.

ii. IP 55 for ODU panel.

All MCCB’s shall be provided with operating mechanism for door interlock.

All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire.

Providing cable clamps / supports within distribution boards cable alley.

Current density of aluminium shall be 1sq mm for 1.0 Amps for rated current of bus bars.

Model, current capacity location and frame size of switchgear shall be written inside of the panel doors with paint / permanent marker as approved shop drawings / site requirment.

All meter shall be digital type and all starter shall be as per Type-2 Coordination chart

Current Transfomer shall be resin cast.

All Panel Shall be BMS Compitable

Spcl. Note: All Panels, Cable tray,Power Cable etc. Supprots incl. Supply, Fabrication, installation and testing of Steel Wire Ropes and Hangers, Supports and Modular system – Wire rope Supports (double channel wedge lock, unlocking device should not be integral part of grip for added safety) complete with end fixing. Wire Hangers shall be independently tested by reputed third party testing organization to sustain safe working load for 120min at elevated temperature of 175 deg. C or above. System shall be in accordance with the approved shop drawings and as required by the specifications

Floor Mounted Panels with base frame (Min. 75 mm )

Plant/AHU/Fan Panel

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of following LT panels fabricated out of 14 guage CRCA sheet steel in cubical formationwith reinforecment of suitable size angle iron and channel T iron flats. All steel material used in the construction of panels shall be powder coated. A solid busbar shall be provided at the bottom of the panel with two connecting eyes for termination. The boards shall be suitable for 415 volts, 50 Hz, 3 phase , 4 wire supply system. All the hardware used in the fabrication of the panel shall be galvanized with zinc passivation. The panel shall be compartmentalized to accommodate one feeder in each compartment. A vertcal cable alley of suitable width shall be provided to serve on or two vertical feeder sections. Also the opening between the busbar chamber and the feeder section shall be shrouded with bakelite / hylam sheet with min.3 mm thickness.

The panel drawing shall be approved before taking up the fabrication and compitable BMS if in future required.

In All panel Each starter should have remote control and interlocking facilities including auto manual switch, NO/NC contacts for control and must have auto manual operation suitable to take signal from fire alarm panel for automatic operation of fan in case of fire. All smoke /vent. fan panel the starters shall have suitable facility to operate with fire sensing control modules.

Ventilation & Smoke Fan Panel

HVAC Fan Panel MCC-01 to 08,11,12 (Base-03,02,01)

Incoming

1 no. 63 amp MCCB

Phase indicating lights with control fuses.

Breaker ON/OFF/TRIP indicating lights.

Bus Bars

100 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves.

Outgoings

1 nos. 13-18 A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq) )

1 nos. 13-18 A,TP MPCB (with DOL starter )

Panel as described above and in drawings.

HVAC Fan Panel MCC-15,16,17 (GF,1st)

Incoming/Outgoing

1 nos. 2.5-4 A,TP MPCB (with DOL starter )

Phase indicating lights with control fuses.

Breaker ON/OFF/TRIP indicating lights.

Panel as described above and in drawings.

HVAC Fan Panel MCC-18 (GF)

Incoming/Outgoing

1 nos. 4-6.3 A,TP MPCB (with DOL starter )

Phase indicating lights with control fuses.

Breaker ON/OFF/TRIP indicating lights.

HVAC AHU Panel MCC-3 (Terrace)

Incoming

1 no. 80 amp MCCB

Phase indicating lights with control fuses.

Breaker ON/OFF/TRIP indicating lights.

Bus Bars

100 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves.

Outgoings

1 nos. 20-25 A,TP MPCB (To AHU Blower VSD, VSD With AHU or AHU with VFD Plug fan )

1 nos. 9-14 A,TP MPCB (To AHU Blower VSD, VSD With AHU or AHU with VFD Plug fan )

1 nos. 6 A, MCB

Panel as described above and in drawings.

ODUs Panel-01 (Left Side Terrace)

Same as above item but outdoor Panel with following accessories.

INCOMING:

1 No. 630 amps, 415V TPN MCCB with overcurrent and short circuit releases, all indication, push button etc.

Coloured (Red, Yellow, Blue) phase indicating lamp - 1 set

BUSBAR:

800 Amp. TPN, 35 kA Al. Bus Bar

OUTGOINGS:

40A, TPN ELCB with 300mA -11 Nos. (Incl. 1No. Spare)

63A, TPN ELCB with 300mA - 06 Nos. (Incl. 1No. Spare)

ODU Panel Described as above/As per Manufacturer ODU Configuration.

ODUs Panel-02 (Right Side Terrace)

Same as above item but outdoor Panel with following accessories.

INCOMING:

1 No. 400 amps, 415V TPN MCCB with overcurrent and short circuit releases, all indication, push button etc.

Coloured (Red, Yellow, Blue) phase indicating lamp - 1 set

BUSBAR:

500 Amp. TPN, 35 kA Al. Bus Bar

OUTGOINGS:

40A, TPN ELCB with 300mA -11 Nos. (Incl. 1No. Spare)

63A, TPN ELCB with 300mA - 03 Nos. (Incl. 1No. Spare)

ODU Panel Described as above/As per Manufacturer ODU Configuration.

ODUs Panel-03 ,04(VIP Block Terrace)

Same as above item but outdoor Panel with following accessories.

INCOMING:

1 No. 250 amps, 415V TPN MCCB with overcurrent and short circuit releases, all indication, push button etc.

Coloured (Red, Yellow, Blue) phase indicating lamp - 1 set

BUSBAR:

300 Amp. TPN, 35 kA Al. Bus Bar

OUTGOINGS:

40A, TPN ELCB with 300mA -06 Nos. (Incl. 1No. Spare)

63A, TPN ELCB with 300mA - 04 Nos. (Incl. 1No. Spare)

ODU Panel Described as above/As per Manufacturer ODU Configuration.

CABLING (POWER )

Power Cabling and Earthing:

Spcl. All Cables Should be fire survival Cables

Supply, installation, testing & commisioning of Aluminum conductor cables PVC sheathed, armoured cables of 1.1 KV grade with termination glands , identification tags, clamps and saddles etc.

3Cx10 Sqmm

4Cx 10 Sqmm Cu

3Cx 06 Sqmm

3Cx04 Sqmm

2Cx04 Sqmm (Cu Conductor)

4Cx 06 Sqmm Cu

Control Cabling Supply, installation, testing & commisioning of Copper conductor , PVC insulated, PVC sheathed armoured cable of 1.1 KV grade (Which is Interconnecting wiring for the fire alarm system with the AHU and the smoke dampers and AHU to Panel).

8C x 1.5 Sqmm

2C x 1.5 Sqmm Cu Cable (control cum transmission wiring in medium duty PVC Conduit between indoor and outdoor units.)

2C x .5 Sqmm

Supplying and making outdoor end termination of cable termination of above cables with Al./copper lugs & flameproof brass compression glands on both the ends with inhibting compound etc. complete as required.

3Cx10 Sqmm

4Cx 10 Sqmm Cu

3Cx 06 Sqmm

3Cx04 Sqmm

2Cx04 Sqmm (Cu Conductor)

4Cx 06 Sqmm

Supplying and installing following size of perforated Hot dipped G.I. cable trays, G.I. bends with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with suitable suspenders above in general points complete as required.

100 mm. Width x 50mm. Depth x 1.6mm. Thickness.

150 mm. Width x 50mm. Depth x 1.6mm. Thickness.

225 mm. Width x 50mm. Depth x 1.6mm. Thickness.

300 mm. Width x 50mm. Depth x 1.6mm. Thickness.

450 mm. Width x 50mm. Depth x 1.6mm. Thickness.

Supplying and Laying following size of G.I. wire on surface or in recess for loop earthing alongwith the existing surface/ recessed conduit/ submain wiring / on cable tray/ on surface including G.I. clamps etc. complete as required.

6 SWG G.I. wire

Supply , Installation , Testing and Commissioning of Microprocessor based Multi-loop, True Peer-to-Peer Networkable Addressable Fire Alarm Control Panel with minimum 600 characters LCD display, 4000 event plus 1000 alarm log history events, QWERTY keypad for programming. The panel should be equipped with sufficient numbers of loops considering 20% spare capacity in each loop. Each loop shall have a capacity of minimum 300 analog addressable devices. The panel shall work in degrade mode in case of CPU failure, Products not having this feature may offer Redundant CPU. Four access levels, flash EPROM, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and 30 mins in alarm condition. The panel shall be complete with 2 ways Communication Fire Fighters System capable of supervising all the speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU shall not result in failure of DVC operation. The Fire Fighters Telephone System shall be capable of having minimum 30 Telephones in conference in multiple FFT Risers. Designed to meet UL864, 10th Edition & FM Approved

6 Loop Panel Expandable to 10 Loops

Supply , Installation , Testing and Commissioning of Network Repeater Panel with minimum 10" Color Touch Screen display with QWERTY Keypad, mapping minimum 2,00,000 points on network. The NRP shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of NRP operation. UL & FM Approved

Supply , Installation , Testing and Commissioning of Graphics User Interface for Monitoring & Control of complete Fire, Voice Evacuation & Telephone Talkback System. The GUI based main network software shall network with other panels on True Peer-to-Peer network. It shall be capable of graphically representing each facility being monitored with floor plans and icons depicting the actual locations of the various systems, and / or sensors’ locations. It shall have the facility to change the sensitivity of any detector. The software shall be capable of monitoring 200 Nodes with 100 Mbps Transmission rate on Fibre Optics Network and 12 Mbps Transmission on cable and 2,50,000 network points. The software shall be capable to Monitor & Control all the Digital Voice Evactuation as well as 2 way communication from main control room using voice signals over Fire Network along with the Fire detection signal. The Graphic workstation shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of GUI. UL & FM Approved

Supply , Installation , Testing and Commissioning of MODbus/Bacnet Interface Gateway for communication with BMS / Other Utilities. MODbus shall support minimum 12000 data points. MODbus Gateway shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of MODbus Gateway. UL & FM Approved.

Supply , Installation , Testing and Commissioning of Addressable Multi-criteria Photo-Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The intelligent multi criteria detection device shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to distinguish between a fire condition and a false alarm condition by examining the characteristics of the thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive phenomena. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches. Designed to meet UL268, 7th Edition & FM Approved

Supply , Installation , Testing and Commissioning of Addressable Smoke dectector. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches. Designed to meet UL268, 7th Edition & FM Approved

Supply , Installation , Testing and Commissioning of Addressable Rate of Rise Heat Detector rated at 8.3 deg C/min. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches. Designed to meet UL268, 7th Edition & FM Approved

Supply , Installation , Testing and Commissioning of Addressable Beam Detector. The beam detector shall be used for High Ceiling application with a detection range upto 100 mtrs having 4 manual & 2 auto sensitivity settings. The beam detector shall be True addressable installed on the SLC circuite & communicate directly with the panel without any interface module. UL & FM Approved

Supply , Installation , Testing and Commissioning of Addressable Manual Call Point (Pull down / Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. UL & FM Approved

Supply , Installation , Testing and Commissioning of Addressable Control Module for Sounders / Strobes / Sounder cum Strobes. The control module shall provide supervised NAC output rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance. UL & FM Approved

Supply , Installation , Testing and Commissioning of Addressable Relay Module for AHU, Access Control, Lifts, Staircase Pressurization, Fire Suppression & other Third Party Outputs. The relay module shall provide contact rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance. UL & FM Approved

Supply , Installation , Testing and Commissioning of Addressable Monitor Module for Sprinklers, Panic Bars & other Third Party Inputs. The monitor module shall monitor potential free contacts. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance. UL & FM Approved

Supply , Installation , Testing and Commissioning of Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance. UL & FM Approved

Supply , Installation , Testing and Commissioning of Sounder cum Strobe rated at 80 dBA @ 3m for Audible annunciation and 115cd flashintg at 1 Hz for visual indication. UL Listed & FM Approved

Supply , Installation , Testing and Commissioning of Addressable Fire Fighter's Telephone Jack with suitable supervised module for two way communication between Remote Fire Fighter & Fire Command Center. UL Listed.

Supply , Installation , Testing and Commissioning of Fire Fighter's Telephone Handset for two way communication between Remote Fire Fighter & Fire Command Center. UL & FM approved

Supply,Installation,Testing & Commissioning of 2 C x 1.5 sq.mm Armoured FIRE SURVIVAL cable with XLPE insulation as per IEC‐60502:2004 Part‐1 (Armoured), Retain circuit integrity as per BS‐6387, CWZ, BSEN 50200, BS‐7846. (armoured), (Resistance to fire at 950o C for 3 hours), Outer sheath will be in Red colour.

SITC of integrated Audio source with the following features : • Two single CD\USB\SD and DAB\FM line outputs can play music applications in two areas. • The volumes of the two line outputs can be adjusted separately. • CD\USB\SD has three play modes: single play, all play and repeated play. • DAB\FM can preset 10 channels of programs. • RS485 remote control interface

SITC of 1X500W Class-D Amplifier with 2 independent channels and can provide automatic re-settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection

SITC of 6W Ceiling Speaker with max SPL1M/1W 96dB . Frequency response of 80Hz-20KHz with a dispersion angle of 160 deg. The speaker should have tappings at 6W/3W/1.5W

SITC of 6W Wall mount with max SPL1M/1W 96dB . Frequency response of 160Hz-20KHz. The speaker shoud have tappings at 6W/3W

Supply,Installation,Testing & Commissioning of 2 C x 1.5 sq.mm Armoured FIRE SURVIVAL cable with XLPE insulation as per IEC‐60502:2004 Part‐1 (Armoured), Retain circuit integrity as per BS‐6387, CWZ, BSEN 50200, BS‐7846. (armoured), (Resistance to fire at 950o C for 3 hours), Outer sheath will be in Black colour.

Supply,Installation,Testing & Commissioning of 2 C x 1.5 sq.mm power cable for Hooter Cum Strobe

Supply, Installation of Brackets for Mounting Speakers

Supply , Installation , Testing and Commissioning of workstation ( I7 PC, with 8 GB RAM and 1 TB HDD, 100/1000 Mbps Ethernet card, USB connection and internal modem, Microsoft(R) Windows(R) 10 OS Professional Enterprise, Web Server Software, DVD-ROM Drive (with RAM), 100/1000 Mbps NIC for Network connection and antivirus software with 22" colour graphics monitor as per Tender Specifications. Accessories included Optical Mouse, Key Pad.)

BMS Computer System: server grade Pentium i5/7 Core with 3GHz minimum CPU speed, minimum of 2 GB RAM, 512 KB cache, 52X32X52X DVD/CD-RW Drive & 260GB HDD, optical Mouse, 106 keys keyboard, 10/100 Mbps Ethernet card ,USB connection & internal modem - I-7 Processor (Latest Generation) - 8 GB RAM, 2 TB hard disc -3½” disc drive, DVD writer, compatible CDROM 42” flat screen, 1200 2 800, 256 colours (Full HD) Windows 7 and shall have MS-Office installed - 132 Column 240 CPS Printer

BMS System Software : Web Based Graphical Software meeting the requirements in the Given I/O Summary & technical specifications including configuration and facility to create / provide the graphic mapping for all I/O Summary points, animate the Graphics, Navigation between pages, display of logs, changing the time zones, popup alarms, configurable password protection for Building Mgmt System as per Specifications. Software shall be able to communicate with Lon works, Bacnet, Modbus devices simultaneously, with unlimited user license capacity.

Supply , Installation , Testing and Commissioning of UL listed, BTL certified, Hardware Interface/Soft integrators with inbuilt webbrowser for third party equipment, Open Protocol Software Integration. These integrators shall be of same make as DDCs and shall contain all necessary ports for software intgeration of systems as per IO Summary

Supply , Installation , Testing and Commissioning of DDC Controller with I/O module, expandable to meet the IO summary listed, The controllers shall be minimum 32 bit Double microprocessor based standalone working on TCP/IP on Bacnet IP with integral web browser, calender fundtion complete with day, month, week, year etc, real time clock & 1 second scan time. DDC working on 230V AC are preferred. The DDC's shall be capable of peer to peer communication without help of communication controller / router / system interface controller / PC and shall communicate with the building LAN directly. These shall come with lockable mounting cabinets duly powder coated connector strip, internal wiring and space to house controller & relays, connector strip step down transformer, MCB, internal wiring. (Contractor shall confirm his I/O provision w.r.t requirement on basis of data point) on AHRAE approved Bacnet/Modbus protocol. DDCs shall work on either 230V power supply or shall contain UL listed SMPS in the panel

DDC for chiller plant, primary pumps, secondary pumps

DDC for FCU's/ Indoor Units

DDC for AHUs/CSU (Not more than 2 AHUs in single DDC)

DDC for Ventilation fans

DDC for pressurization fans

DDC for HT/ LT Transformer panels

DDC for fire Damper

DDC for STP and other plumbing systems

DDC for fire fighting systems

DDC for Sump systems

DDC for DGs

L2/L3 network switches of suitable specifications to create the desired LAN for IP based DDCs. The specifications and number of the switches shall be calculated based on the design and DDC configuration. All the required accessories, racks etc, shall be included in this line item

Field Devices Supply, installation, testing, commissioning of necessary Input sensor transmitters/transducers comprising the following:

Immersion Temp Sensor for CHW line with brass thermowell. Measuring range: -30 to 110 Deg C, Accuracy: +/- 1.3 Deg C

Outside Temp & Humidity Sensor with radiation shield. Measuring Range: Temp:-30 to 50 Deg C & RH 0-100%, Accuracy: +/- 1 Degc +/- 3%

Water Differential pressure switch. Trigger Range:150-1000mbar with 1A (resistive) @ 240V AC contact rating

Water Pressure Sensor . Accuracy:+/-0.3% FSL

Duct type temperature sensor Measuring range: -30 to 110 Deg C, Accuracy: +/- 1.3 Deg C

Current Relay

Differential pressure switch for filters & Blowers

Level Switches (Hi/Low)

Thermostate

CO Sensor

DPT- Water

CO2 Sensor

Water Flow Switch

Ultrasonic Water Flow Meter (Clamp-On)

Conduiting , Wiring and cabling Supply, installation, testing and commissioning of following cables:

2 Core 1.0 Sqmm, unarmoured ATC conductor multistranded, twisted unshielded cable for signals

3 Core 1.5 Sqmm, unarmoured ATC conductor multistranded, cable for Powering DDC , Actuators.

Cat-6 networking cable

2 Core 1.5 Sqmm, unarmoured ATC conductor multistranded, twisted shielded cable for integration of 3rd Party Devices

Supplying and laying of following sizes of Heavy Duty PVC conduit on surface/recess including cutting/filling chases along with conduit accessories etc. complete as required.

25 mm dia

20mm dia

25mm PVC conduit.

Supply, Laying, testing & commissioning of 6 Core Multimode OM4 armoured Fiber Cable

Supply, installation, testing & commissioning of 48 Port 1U 19" Rack Mount LIU, Drawer type, Fully loaded with SC type Duplex Adapters, , Splice Tray to accommodate 48 fibers

Supply, installation, testing & commissioning of 12 Port 1U 19" Rack Mount LIU, Drawer type, Fully loaded with SC type Duplex Adapters, Splice Tray to accommodate 12 fibers

Supply, installation, testing & commissioning of LC Pigtail.

Supply, installation, testing & commissioning of LC-SC Patch Cord MM, Duplex, 2 mts.

Supply, Laying, testing & commissioning of 6 UTP Solid cable LSZH 4-pair unshielded twisted pair with 23 AWG solid copper conductor

Supply, installation, testing & commissioning of CAT 6 24 port non shuttered Patch Panel with rear cable tray, loaded For DATA /VOICE/CCTV

Supply, installation, testing & commissioning of CAT 6 RJ 45 Connector for CCTV & WIFI

Supply, installation, testing & commissioning of CAT 6 Key Stone Jack Blue Colour For DATA Point

Supply, installation, testing & commissioning of CAT 6 Key Stone Jack Yellow Colour For Voice Point

Supply, installation, testing & commissioning of CAT 6 Patch Cord 1mtr for Rack End Side (for CCTV)Red Colour

Supply, installation, testing & commissioning of CAT 6 Patch Cord 1mtr for Rack End Side (forVoice) Yellow Colour

Supply, installation, testing & commissioning of CAT 6 Patch Cord 1mtr for Rack End Side (for Data ) Blue Colour

Supply, installation, testing & commissioning of CAT 6 Patch Cord 1mtr for Rack End Side (for Wifi)Green Colour

Supply, installation, testing & commissioning of CAT 6 Patch Cord 2mtr for User End Side (for Data ) Blue Colour

Supply, installation, testing & commissioning of CAT 6 Patch Cord 5mtr for User End Side (for Data ) Blue Colour

Supply, installation, testing & commissioning of 1U Horizontal Cable Manager, panel with metal grooves , plastic snap on cover with 50 patch cord capacity

Supply, installation, testing & commissioning of 50 Pair Riser unarmoured Cable

Supply, installation, testing & commissioning of 400 Pair Mdf Box with Krone Module

Supply, installation, testing & commissioning of 2 Pair Jumper Cable (90 mtr Roll)

Supply Installation, Testing and Commissioning of RG11 Coaxial Cable

Supply Installation, Testing and Commissioning of RG6 Coaxial Cable

Supply, installation, testing & commissioning of 1X8 Coaxial Splitter

Supply, installation, testing & commissioning of TV Port with Face Plate

Supply, installation, testing & commissioning of 9U Rack (600x600mm) with all accessories and06 port PDU

Supply, installation, testing & commissioning of 15U Rack (600x600mm) with all accessories and06 port PDU

Supply, installation, testing & commissioning of 21 U Rack (600x600mm) with all Acessoseris and 12 port PDU

Supply, installation, testing & commissioning of 24U Rack (600x600mm) with all Acessoseris and 12 port PDU

Supply, installation, testing & commissioning of 42 U Rack (800x800mm) with all Acessoseris, 2x10/12-Port 5/15A Power Distribution Board

Supply, installation, testing & commissioning of 42 U Rack (800x1200mm) with all Acessoseris, 2x10/12-Port 5/15A Power Distribution Board

Supply, installation, testing & commissioning of Core Switch 1RU 10GE L3 fixed chassis with 48 10G SFP+ and 6 40G QSFP+ ports as per technical specs.

Supply, installation, testing & commissioning of Distribution Switch 10GigE fixed chassis 8 SFP+ 10GigE, 2 QSFP+ (20G) stacking ports. 1RU size. Includes Stack Cables, power cord, guides, and 19” rack mount hardware

Supply, installation, testing & commissioning of 1RU fixed chassis 24 RJ-45 10/100/1G BaseT, 2 fixed SFP (1G), 4 fixed SFP+ (1G/10G) uplink/stacking ports. 1RU size, internal AC power supply. Includes United States power cord, guides, and 19" rack mount hardware.

Supply, installation, testing & commissioning of 1RU fixed chassis 24 RJ-45 PoE 10/100/1G BaseT, 2 fixed SFP (1G), 4 fixed SFP+ (1G/10G) uplink/stacking ports. 1RU size, 600W AC power supply. Includes United States power cord, guides, and 19" rack mount hardware.

Supply, installation, testing & commissioning of 1RU fixed chassis 48 RJ-45 PoE 10/100/1G BaseT, 2 fixed SFP (1G), 4 fixed SFP+ (1G/10G) uplink/stacking ports. 1RU size, 920W AC power supply. Includescountry specific power cord, guides, and 19" rack mount hardware.

Supply, installation, testing & commissioning of 10G DAC (Stack) Cable 1m

Supply, installation, testing & commissioning of 10 Gigabit optical transceiver (SFP+). Supports multimode fiber over 850 nm wavelength (nominal) with an LC connector.

Supply, installation, testing & commissioning of Indoor AP Dual radio 4x4 802.11a/b/g/n/ac/ax MU-MIMO AP, integrated antenna, 1x GbE, 1x2.5GbE RJ-45 Port, 1xConsole Port

Supply, Installation, testing & commissioning of Indoor AP Dual radio 2.4/5 Ghz 2x2:2 802.11ax, integrated omni antenna. 2x 1GbE uplink, 1x RS-232 Console, USB, 48V DC.

Supply , Installation , Testing and comissioning of Wireless Controller with 150 AP licenses

Network Management System for managing both wired and wireless devices with upto 150 device license

1U RACK Server, INTEL XEON E3-1220v5, Processor, 3.0 Ghz Cache - 8MB FSB - 1600 MHz STD Memory - 8GB x 1 Max. Memory - 32GB (4 SLOTS) HDD - 3 x 1TB, HDD Bay's - 4 BAY, Optical DVD WRITER, 1PCIe x16 3.0 Raid Capability, Power Supply In-Built) + 1 RPS, Latest Windows Server OS.

Supply, installation, testing & commissioning of USG (Unified Security Gateway) - supporting upto 200 users, having Minimum of 4 WAN & 8 (Giga) LAN ports (which can be either way configured) - Rack mountable in HA mode.

Supplying Installation, Testing and Commissioning of Server Based Call server - Duplex ( Fully Redundant, Hot standby mode) Linux OS Platform, single server with redundant power supply. Should be able to populate all necessory hardwares and PMS interface enabled. Media Gateway Chasis for staff quarter block. PRI(30 Channel) 01 Nos. IP/ SIP Extension 20 Nos Analog Extension 170 Nos Conference Upto 29 party conference

Operator Console IP Deskphone with 40 addon keys

Type 1: IP Deskphone, 64x128 backlit black and white LCD, 6 soft keys, Handsfree, Wideband Comfort Handset, 2 Gig Ethernet Ports, USB, POE or power supply

Type 2: IP Deskphone , 3.5" 320x240 Color display, Wide Band Corded Comfort Handset, Alphabetic Keyboard, Jack 3.5 mm 4 poles, Integrated 4 lighted key Smart add-on module, USB, 10/100/1000 PC Connectivity POE

Type 3: Bathroom phone: Single line analog slim phone with flash, redial, message waiting light, membrane keypad and SOS key.

Supply Installation, Testing and Commissioning of Premium guest room telephone, speaker phone, message waiting lamp and retreival key, full length face plate, flash key and programmble flash timing, upto 10 guest service keys.

PMS, POS, ACCOUNTS, PURCHASE, MMS, PBX INTERFACE.

Web Prolific full & lite users- Hotel Access

WISH Front Office (minimum 50 room)

Touche POS desktop

SmartTEL - PABX interface

Channel Manager interface with WISH FO - Staah

Guest Internet Interface

Software installation & configuration

User training

Go-live support

Guest Internet System

Guest Internet Management Controller

One time PMS Interface

Gen9 E3-1240v6 1P 16GB-R H240 4SFF 900W PRS Performance Server Default Components: Processor(s) - (1) Intel® Xeon® E3-1240v6 (4 core, 3.7GHz, 8MB, 80W) Memory - 16GB (1x16GB) Registered DIMMs NOTE: Only Support Single CPU, 4 DIMM Slots available Network Controller - 1GB 332i Ehternet Adapter 2 ports Network Interface Storage Controller - HP H240 FIO Smart Host Bus Adapter (761873-xx1) Hard Drive - None ship standard Internal Storage - 4 SFF HDD Bays Optical Drive - (1) (Optional: DVD-ROM, DVD-RW) Power Supply - (1) HP 900W Standard AC 240VDC Power Input Module FIO Kit Fans - 3 hot swap fans, non-redundant Management - HPE Shared iLO Management Engine (standard) & HP Insight Control Standard Form Factor - 1U, HP 1U Short Friction Rail Kitincluded (775612-B21) Warranty - Server Warranty includes 3-Year Parts, 3-Year Labor, 3-Year Onsite support with next business day response, Windows 2019 R2 Standard Server license - English, SQL SvrStd 2017 SNGL OLP NL, SQL CAL 2017 SNGL OLP NL DVC CAL

POS - 15" Ubiquitous Bezel free POS Terminal, Bay Trail quad core J1900 (upto 2.42Ghz),4GB RAM, 64GB SSD,1. IP 65 sealed front panel with touch design,5 USB, 2 Serial, 1 LAN, with 7th gen. base OS versatility ( Windows & Android )

Serial Bill Printer - Fast thermal printer with 250mm/sec,Dimension-195(l)x147(w)x147(h)mm, Serial, RAM 16Mb, Flash 32Mb, power supply AC 100V~240V, 50~60hz

Kot Printer - Fast thermal printer with 250mm/sec,Dimension-195(l)x147(w)x147(h)mm, Standard: Ethernet, RAM 16Mb, Flash 32Mb, power supply AC 100V~240V, 50~60hz

OS posready preload POS ready 7 (latest)

PERSONAL PRINTER (NO NETWORK CONNECTION ALLOWED) Color laser multifunctional A3/A4 color printer 20/20 CL/BW pages per minute, printer, copy, scan, send, store and optional fax, network interface, two 550 sheet paper cassettees, 100 sheet multi-purpose tray, print/copy: 20ppm A4, 50ppm A3, 1200 dpi.

Color laserjet printer, 256DDR, 256Mb, 600x600 dpi upto 40,000 pages duty cycle, upto 21ppm.

Supply, installation, testing and commissioning of 100KVA high performance IGBT inverter and IGBT rectifier based fully microprocessor controlled (three phase Input & three phase Output) online Transformerless UPS system suitable for input and output parameters as per specifications. The UPS shall be provided with internal cu k-13 isolation transformer at the complete input of the UPS i.e. after the static switch (As per IEC1100 -2005). The UPS shall be provided in powder coated fan cooled enclosure painted in colour as per specifications. The UPS shall be suitable for normal, emergency, recharge, by-pass and maintenance mode. The system be expandable in such a manner that addition of another module of similar capacity can double the system output with common by-pass. The UPS shall have a microprocessor based display and control panel. UPS shall have own batteries with 30 minute battery back-up. Complete system must be provided as per specifications approved drawing and as per site requirement including inter connecting cables from battery to UPS, UPS to panel etc.& supports for complete system as approved by the Engineer in charge.

100 kVA on line 415 V AC UPS with 30 minutes balancing battery back up.

Supply installation, testing & Commissioning of Early warning smoke detection system control Panel with Display, Single Zone, Power supply (To be supplied by the Panel Manufacturer) & all required accessories. The panel should have the capability to be integrated to the Intelligent Fire Alarm System.

Supply, installation, testing & Commissioning of Aspiration sampling nozzles / Sampling tubes/Hooter complete with required stickers & necessories elbows & joints.

Supply, Installation, testing & Commissioning of Master Console Capable of connecting to 12 sattelites complete as required and as per specifications.

Supply Installation, testing & Commissioning of Satellite units complete as required and as per specifications.

Supply, installation, testing & Commissioning of Wire Bundles (2C x 1.5 sqmm armoured cable.

Supply, Installation,testing & Commissioning of Water leak Detection Panel/Hooter/Sensing cable

Supply, installation, testing & Commissioning of Wire Bundles (2C x 1.5 sqmm armoured cable.

Server Room PAC, Room temperature and humidity monitoring Unit, Fire Rated Doors 9.5 Tr (Supply , installation) (1Working + 1 Standby) with an auto changeover of 4/6 hours between both the units. Inclusive of below shared Low side work

Supply of Lowside material for I&C of Precision AC unit as per scope defined

Supply of Copper Refrigerant Piping Extra Charge of Refrigerant

Supply of Armoured 3c x 2.5 SQMM Copper Cable

Supply of Insulated GI Drain 32mm Dia

Supply of Humidifier GI Pipe 19 mm Dia

Supply air grills

Supply of Floor insulation with 13mm thick UV laminated cross linked polyethelene

Server Room - supply and fixing of 2 hour fire rated Metal door for server room only, including all fitting.

Temperature & humidity monitor sensor with 2 inch display size

Supply, installation, testing and commissioning of 55" 4K Hospitality Display Panel - 55", 4K - UHD, Android Display, HDMI, USB, LAN, 20W SPK, Wifi, Hotel Mode, HDMI CEC, Web with atleast one year standard warranty. Make : Sony

P AND C PROJECTS PRIVATE LIMITED

SRK ASSOCIATESS